Arcade Typhoon Manual TYPHOON_MANUAL_1.2 User
Typhoon Manual Typhoon Manual
2013-09-30
User Manual: Arcade Typhoon Manual
Open the PDF directly: View PDF 
.
Page Count: 48
| Download | |
| Open PDF In Browser | View PDF |
TYPHOON USER MANUAL Preliminary – January 2009 Triotech Amusement Inc. 190 Des Industries Lavaltrie, Quebec (Canada) J5T 3R2 Tel.: 450.586.5009 Toll free: 1-888-IN-LINE-4 Fax: 450.586.0299 e-mail: service@trio-tech.com Dear valued customer, Congratulations and thank you for purchasing TRIOTECH AMUSEMENT’s Typhoon. You will not be disappointed with your purchase. Your 2-seat theater is coin-operated and does not require attendant. Featuring 4.1 Surround Sound and a 42” LCD screen this dual-actuator motion platform is the most realistic simulation available in coin-op. Sincerely, TRIOTECH Reception Typhoon reception ! 1 CAUTION Typhoon requires a dedicated 120V. 15 amp circuit or 220V. 7.5amp or the machine may experience sporadic technical difficulties. Your Typhoon should not share a breaker with other deluxe or motion based cabinets. Determine Optimum Location The game location must be free of: exposure to direct sunlight, high humidity, dust, salt mist, high heat, or extreme cold. If installed in an unusually hot location, allow additional clearance between ventilation slots in the game and any structure or object that would tend to restrict air circulation. TYPHOON Ships in one (1) crate Package approximate dimensions: 90” x 56” x 80” Reception LIST OF SUPPLIED ASSEMBLY PARTS 2 Package Content Item Description Photo/ Image Qty. 1 Main cabinet 1 2 Motion seat module 1 3 Header assy 1 4 Fan’s cover (right &left) 2 5 Hardware box (inside of the coin door; the access is from the front of the machine; a bag with the necessaries keys is attached to the coin door's door) 1 Reception HARDWARE BOX MANIFEST Bag or bin No. 1 IMAGE SD-100-0215 2 SD-100-0187 3 SD-100-0216 SD-100-0190 6 7 SD-100-0328 SD-100-0047 SD-100-0342 SIZE QTY. #10 26 #10-24 x 3/4" 26 #14 12 1/4-20 x 3/4" 12 LOCK WASHER 1/2" 6 FLAT WASHER 1/2 “ 6 1/2 “-13 x 4” 6 FLAT WASHER NEORENE PAN HEAD QUADREX DRIVE FLAT WASHER NEOPRENE PAN HEAD QUADREX DRIVE 4 5 DESCRIPTION 3 HEX.MACHINE SCREW SPARE Installation NECESSARY TOOLS 4 TO COMPLETE ASSEMBLY Tools Description /Image Application No. 1 Forklift Capacity over 1000 lb Appropriated long forks attached (~65”) 2 Socket 3/4" Put the carrying package in the place Install the seat module (pg.14) 3 Wrench 3/4” Adjust the height of the cabinet and seats (pg.9 and 14) 4 Screwdriver no.2 (square) (Screw #10) Or Phillips #2 Install the fan’s covers on to the header(pg.10 )and the header to the cabinet (pg. 11) 5 Screwdriver no.3 (square) (Screw 1/4) Or Phillips #3 Install the header on the cabinet (pg.11) Installation SPACE REQUIREMENTS 5 For installation, the required space is ~ 15’ X 10’ When fully assembled, the required space will be ~ 7.5’ X 8’ Installation 6 Uncrating 1 - Start by removing the header assembly from the seat. 4-Pull the seat out of the cabinet about 6’’ or 15cm. Then pull the 3 cables out of the hole one by one as shown in the picture below. 2- Remove the header support 5- Remove seat assembly from the crate. 3- Remove the back legs holder 6- Remove cabinet from the crate and move in the desired final location. - Locate the hardware box inside of the coin door - You will find a description of the hardware on the bag. Installation Header 7 STEP 2. Header assembly Install the two fan covers (right and left) to the cabinet Tools Screwdriver no.2 Fasteners Reference Flat neoprene washer #10”(14X), Screw #10-32 x 3/4”(14X) Installation 7 Header STEP 3. Header installation Place the header on the machine as shown Tools Screwdriver no.2 (Down side, upside ) Screwdriver no.2 (right and left side fan’s cover) Fasteners Reference Flat neoprene washer #10”(12X), Screw #10 -32 x 3/4”(12X) BAG/BIN NO: Flat neoprene washer #14”(12X), BAG/BIN NO : Screw 1/4"-20x 3/4”(12X) Installation Header 7 - Open the back service door. - Connect the header cables. There are three connectors; one MOLEX, 9 pin and one 15 pins + one NEMA /standard 110V. Once connected, close & lock top door. Installation 8 Seat Align seats for wires to easily run through hole on lower right part of cabinet. Installation Seat 8 Fasten seats to cabinet using 6 hexagonal head screw 1/2" -13 x 4”, flat and lock washer. Level seats using adjustable feet Tools Ratchet 3/4" Wrench 3/4" Fasteners Reference Flat washer 1/2”( 6X), lock washer 1/2 (6X), Hex. Screw 1/2”-13 x 4”( 6X) Levelling feet Installation 8 Seat Through lower right (back of cabinet) door, connect wires you ran. (Three connectors: NEMA /standard 110V to electric box, RJ45 to Opto board (only one with RJ45 connection) and the Molex 9 pin connector to its female connector Main electric box Opto-card Molex 9-pin Once plugged in, lock door. Installation Installation Before you connect, make sure main switch is in off position. Connect power cord to cabinet and wall outlet. Then turn the main switch ON 9 Configuration 10 Operator Setting Accessing operator settings interface is done by opening the coin mech door and pushing the micro switch attached to the coin mech (while in attract mode only). Configuration Operator Setting 10 To access the statistic mode screen, press the micro switch once (or toggle micro switch until you reach this screen). 1. 2. 3. 4. 5. 6. Amount of credits inserted into game in lifetime. Amount of money inserted into game in lifetime. Value of one credit Actuator usage time since game installed Actuator usage time since game installed Revenue from each movie installed Configuration 10 Operator Setting Use the large dash selection buttons 1 through 6 to change configurations. To change any of the options, press the appropriate button until the desired setting is reached. To return to a previous setting, keep toggling the button until it reaches the end of the settings; then it will restart the settings from the beginning. Amount of credits needed to start game. Set to 0 for free play (Press 1) Choose to display credits or money on screen. (Press 2) Value of one credit. (Press 3) Sound volume in attract mode. (Press 4) Hit the appropriate button on the header to change variables Configuration Dollar bill validator information 11 Typhoon does not ship equipped with a DBV, however it is pre-wired to accept one and we suggest the installation of one of the models below. This door accepts Mars upstacker bill validator with compact fitted Bezel (up to 10” deep) Accepts both bills and coins Fitted with full metal cash box enclosure Fitted with two $.25 U.S. Coin FACTORY SUGGESTED PRICING PER RIDE IS $3.00 Upstacker Bill validator fits these Models amongst others MARS MARS MARS Happ Control P/N 42-7312-00 42-7311-00 42-7310-00 Maintenance 12 Actuator replacement Actuator replacement procedure 1. Unscrew the 2 bolts holding the defective seat (under foot rest) 2. Flip seat back (protect head rest by covering floor with something soft) 3. Remove cover plate between the 2 seats 4. Open cover of control box, and detach the actuators’s 2 connectors from the control box board (see page 38) 5. Remove front cover plate from control box Maintenance Actuator replacement 12 Actuator replacement procedure 6. Unscrew the 4 hex socket screws from inside the actuator positioning hole 7. Unscrew the 5 hex socket screws attaching the actuator to the seat frame 8. Remove actuator 9. Reverse procedure to re-reinstall new actuator Maintenance 13 Replacing a drive assembly Remove drive assembly from motor. Shipping a drive assembly is the cheapest way to get the actuator repaired as you save on shipping (weight). Maintenance Replacing a drive assembly 13 Maintenance 14 Replacing control box A Remove control box cover. E B Unplug all connectors. C Unscrew cable plates. D Pull cables out of box. Remove and replace control box. Diagnostic screen and error codes Continued • • • SYNCRONIZED SYNCRONIZING NOT RESPONDING • • • • • • • Software (overweight)Command OverRunFail State Software (travel)Command OverRunFail State Software (fail hall)Command OverRunFail State Software (overpos)Command OverRunFail State Software (Timeout) Command OverRunFail State Software Command OverRunFail State No problem reported with this actuator Move to box below Goto page 43 Goto page 36 Goto page 36 Goto page 41 Goto page 41 Goto page 38 Goto page 42 Goto page 40 Troubleshooting 15 Troubleshooting 16 Diagnostic screen and error codes Continued Software (Travel) Software (overweight) Software (overweight) Command OverRun Fail State Software (OverPos) Software (Travel) Command OverRun Fail State Cause - Mechanical fault -Unplug the Typhoon. -Lift the back of each seat to see if they move freely. MOVES FREELY -Re-seat actuator on side the error appeared (diagnostic screen). Verify coupler & tighten (see section 20). If no change, replace whole actuator. DOES NOT MOVE FREELY -Replace DRIVE ASSEMBLY Diagnostic screen and error codes Continued Software (Fail Hall) Software (Fail encoder) Cause - Electrical fault -Replace whole ACTUATOR on side error appears. Section 3-3. Troubleshooting 17 Troubleshooting 18 Diagnostic screen and error codes Continued Software (Timeout) Cause - Actuators have not received data from computer for more than one minute -Unplug machine -Wait 1 minutes -Re-plug machine Diagnostic screen and error codes Continued Troubleshooting 19 Software Software Command OverRun Fail State • • Cause Machine is sharing breaker with other devices. Machine is not receiving at least 115volts. -Verify voltage I have more then 114volts. Go to Step B B I have less then 115volts. Plug machine into other outlet with at 115volts. If you do not have the minimum requirements, call an electrician. -Verify if machine is alone on breaker. It is alone It is not alone Use another breaker or unplug all other games -Get mouse and keyboard out. -Press ESC. -Go to WINDOWS EPLORER. -Copy C:\MotionTheater\Motion_Theater.log on floppy disk. -Email file at SERVICE@TRIO-TECH.COM -Wait 10 minutes and call Tech Support @ 1-888-465-4634 Troubleshooting 20 Diagnostic screen and error codes Continued Software (overPos) Command OverRun Fail State Software (fail hall) Command OverRun Fail State Cause - Mechanical, electrical and/or software fault B -Remove Actuator from the side error appears on. (Sec 3-3) -Verify condition of Coupler (small aluminum cylinder Linking Drive Assembly and Motor. Coupler is in perfect condition -Replace actuator Coupler is loose or broken -If coupler is loose, use HEX key to tighten. -If coupler is broken, call Tech Support @ 1-888-465-4634 to get replacement. Diagnostic screen and error codes Continued Troubleshooting 21 Command OverRun Fail State - When error appears as is, without the word software, no problem is detected on this actuator. Troubleshooting 21 Diagnostic screen and error codes Continued Not Responding Cause - No communication or no power going to actuators. Step 1 -Open service door on bottom left in the back of the game. -Look inside at Actuator control Board. Light is RED or GREEN (LED) -Go to next step There is power -Replace Actuator control board. There is power -Replace Power Cord between Power Supply and Actuator Control Board. There is power -Replace Power Supply. No light (LED) -Check power on board power cord. -Verify power output on Power Supply (top right of the back of the game). There is no power -Verify power Input on Power supply ( red LED), Light is YELLOW (LED) -Check power on board power cord. -Unplug power cord on board. Disconnect network and serial cables. Re-connect power cord. If light is yellow replace board, if green goto next step. -Reconnect network cable, if light turns yellow replace network cable. If light is green reconnect serial cable, if light turns yellow replace serial cable. There is no power -Replace Power Cord going Continued next page Diagnostic screen and error codes Continued Troubleshooting Not Responding Step 2 -Open service door on bottom left in back of the game. -Look inside and test Power on Power Outlet There is Power -Remove seat assembly -Connect another Power cord to Control Box (IF EQUIPPED WITH CONTROL BOX) -Restart computer There is Movement -Replace Power Cord(s) There is no power -Open Outlet and repair connections. 22 Troubleshooting 23 Motion stops and restarts during ride Cause - One or more Actuator is faulty, but does not generate an error in the Diagnostic Screen. -Get mouse and keyboard out. -Press ESC. -Go to WINDOWS EXPLORER. -Copy D:\Typhoon.log on floppy disk. -Email file at SERVICE@TRIO-TECH.COM -Wait 10 minutes and call Tech Support @ 1-888-465-4634 Parts Parts 24 Parts 25 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Seat assembly PART NUMBER SD-450-0003 SD-450-0008 SD-450-0022 SD-250-0068 SD-400-0010 SD-900-0015 SD-450-0013 SD-350-0015 SD-500-0040 SD-500-0039 SD-700-0070 SD-250-0336 SD-150-0019 IMT- 0151 DESCRIPTION PIVOT ASSEMBLY ACTUATOR MOTOR AKM 24D DRIVE ASSY AC10 ACTUATOR PLATE SKIRT, RUBBER BASE CAP PIVOT PISTON CONTROL BOX "B" FIBER GLASS SEAT HEAD CUSHION BACK REST CUSHION 3" SPEAKER ASSEMBLY GRILL NETWORK CABLE SOUND WIRING HARNESS Parts Header parts ITEM 1 2 3 4 5 6 7 8 9 10 11 PART NUMBER SD-400-0071 SD-400-0075 SD-400-0074 SD-700-0065 SD-250-0336 SD-150-0091 SD-150-0090 SD-400-0072 SD-400-0077 IMT-0269 SD-650-0118 DESCRIPTION HEADER FAN CASING, RIGHT FAN CASING, LEFT SPEAKER 5.25_2 WAY CABINET SPEAKER GRILL RED BUTTON BLUE BUTTON HEADER TOP COVER FAN GRILL HEADER HARNESS HEADER BACKLITE SIGN 12 SD-650-0117 FRON HEADER DECAL 13 14 15 16 SD-550-0018 IMT-0226 SD-150-0420 SD-400-0073 NEON FIXTURE FAN PROTECTION FAN 10" X3.5" AC115V FUNNEL 26 Parts 27 Cabinet ITEM 1 2 3 4 5 5 5 6 7 8 9 10 PART NUMBER SD-150-0035 IMT-0270 SD-150-0098 SD-150-0297 SD-150-0370 IMT-0303 SD-700-0117 IMT-0040 SD-700-0075 IMT-0271 SD-700-0129 SD-150-0436 DESCRIPTION COIN DOOR COMPUTER ASSEMBLY 5-12v POWER SUPPLY I/O INTERFACE 10A TRANSFORMER BLOWER CONTROLLER 4.1 SOUND AMPLIFIER ACTUATOR CONTROL BOARD SUB-WOOFER 6-1/2 WIRING HARNESS (CABINET) MONITOR 42"LCD BLUE LED 110v CABINET ELECTRIC SCHEMATICS Electrical 28 230v CABINET ELECTRIC SCHEMATICS Electrical 29 110-230v HEADER ELECTRIC SCHEMATICS Electrical 30 110-230v SEAT ELECTRIC SCHEMATICS Electrical 31 Technical Support 190 Des Industries Lavaltrie, Quebec Canada J5T 3R2 1-888-IN-LINE-4 Fax: 450.586.0299 www.trio-tech.com info@trio-tech.com LIMITED WARRANTY Triotech warrants to the buyer, for a period of (1) one year starting on the day of product delivery, all parts against any manufacturer’s defect. During this warranty period, Triotech agrees to replace defective parts. Installation costs onsite are at the charge of the buyer. Ground Freight costs for replacement parts are at the charge of Triotech, For the return of the defective part. The buyer agrees to send back defective parts to Triotech within (30) thirty days and freight costs will be at his charge. The warranty is limited to manufacturer’s defects. As for parts or components not manufactured by Triotech, the only valid warranty is that of the manufacturer’s. Triotech assumes no liabilities for any loss of revenue, damage or inconvenience of any type resulting from a defect of any part of the system and will not assume the temporary replacement of the system during the period of repair. Triotech is not liable of any late delivery of the system. Any apparent defect or non-delivery of a part of the system shall be notified in writing within 5 days of delivery. Defective parts covered by the warranty will be replaced at Triotech’s discretion either by new or rebuilt parts with the same or with a replacement model of the same parts. Warranty on replacement parts ends on the same date as the original part warranty. No warranty is valid if the defect is the result of a misusage, or contrary to the norms of instruction or user manuals, or the result of improper maintenance. Using spare parts that do not fit specifications will void the warranty. Removing serial numbers and/or bar codes from product or component will void the warranty. Triotech is only liable to the replacement, in a reasonable delay, of the defective parts. No warranty is granted on the productivity of the system sold or on the result of its use.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2009:02:03 15:36:28-05:00 Create Date : 2009:02:03 15:36:28-05:00 Format : application/pdf Title : TYPHOON_MANUAL_1.2 Creator : s.lachance Document ID : uuid:70cea220-1f8b-437c-bfc9-a7f074f1a533 Instance ID : uuid:993104cd-0e08-4489-af48-c5ef71968d35 Page Count : 48 Author : s.lachanceEXIF Metadata provided by EXIF.tools