Arcadyan Technology WG7005D Draft 11n Wireless 4-port Broadband Router User Manual 00

Arcadyan Technology Corporation Draft 11n Wireless 4-port Broadband Router 00

UserManual.wiki >

Arcadyan Technology >

WG7005D User Manual

User Manual

SMCWBR14S-N2Barricade™ NDraft 11n Wireless 4-port Broadband Router

20 MasonIrvine, CA 92618Phone: (949) 679-8000Wireless Broadband Router User’s GuideFrom SMC’s line of award-winning connectivity solutionsSeptember 2007R01 F/W 1.0

Information furnished is believed to be accurate and reliable. However, no responsibility is assumed by our company for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of our company. We reserve the right to change specifications at any time without notice.Copyright © 2007 by SMC Networks, Inc.20 MasonIrvine, CA 92618All rights reserved.Trademarks:Product and company names are trademarks or registered trademarks of their respective holders.

iLIMITED WARRANTYLimited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. All SMC products carry a standard 90-day limited warranty from the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion, repair or replace any product not operating as warranted with a similar or functionally equivalent product, during the applicable warranty term. SMC will endeavor to repair or replace any product returned under warranty within 30 days of receipt of the product.The standard limited warranty can be upgraded to a Limited Lifetime* warranty by registering new products within 30 days of purchase from SMC or its Authorized Reseller. Registration can be accomplished via the enclosed product registration card or online via the SMC web site. Failure to register will not affect the standard limited warranty. The Limited Lifetime warranty covers a product during the Life of that Product, which is defined as the period of time during which the product is an “Active” SMC product. A product is considered to be “Active” while it is listed on the current SMC price list. As new technologies emerge, older technologies become obsolete and SMC will, at its discretion, replace an older product in its product line with one that incorporates these newer technologies. At that point, the obsolete product is discontinued and is no longer an “Active” SMC product. A list of discontinued products with their respective dates of discontinuance can be found at:http://www.smc.com/index.cfm?action=customer_service_warranty.All products that are replaced become the property of SMC. Replacement products may be either new or reconditioned. Any replaced or repaired product carries either a 30-day limited warranty or the remainder of the initial warranty, whichever is longer. SMC is not responsible for any custom software or firmware, configuration information, or memory data of Customer contained in, stored on, or integrated with any products returned to SMC pursuant to any warranty. Products returned to SMC should have any customer-installed accessory or add-on components, such as expansion modules, removed prior to returning the product for replacement. SMC is not responsible for these items if they are returned with the product.Customers must contact SMC for a Return Material Authorization number prior to returning any product to SMC. Proof of purchase may be required. Any product returned to SMC without a valid Return Material Authorization (RMA) number clearly marked on the outside of the package will be returned to customer at customer’s expense. For warranty claims within North America, please call our toll-free customer support number at (800) 762-4968. Customers are responsible for all shipping charges from their facility to SMC. SMC is responsible for return shipping charges from SMC to customer.

LIMITED WARRANTYiiWARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. SMC SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN IF SMC OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS WARRANTY SHALL BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS.* SMC will provide warranty service for one year following discontinuance from the active SMC price list. Under the limited lifetime warranty, internal and external power supplies, fans, and cables are covered by a standard one-year warranty from date of purchase.SMC Networks, Inc.20 MasonIrvine, CA 92618

iiiCOMPLIANCESFederal Communication Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.IMPORTANT NOTE:FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.For product available in the USA market, only channel 1~11 can be operated. Selection of other channels is not possible.

COMPLIANCESivEC Declaration of Conformity SMC contact for these products in Europe is:SMC Networks Europe,Edificio Conata II,Calle Fructuos Gelabert 6-8, 2o, 4a,08970 - Sant Joan Despi,Barcelona, Spain.Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards:EN 300 328 EN 301 489EN 60950-1Countries of Operation & Conditions of Use in the European CommunityThis device is intended to be operated in all countries of the European Community. Requirements for indoor vs. outdoor operation, license requirements and allowed channels of operation apply in some countries as described below:Note: The user must use the configuration utility provided with this product to ensure the channels of operation are in conformance with the spectrum usage rules for European Community countries as described below.• This device will automatically limit the allowable channels determined by the current country of operation. Incorrectly entering the country of operation may result in illegal operation and may cause harmful interference to other system. The user is obligated to ensure the device is operating according to the channel limitations, indoor/outdoor restrictions and license requirements for each European Community country as described in this document.• This device may be operated indoors or outdoors in all countries of the European Community using the 2.4 GHz band: Channels 1 - 13.

COMPLIANCESvDeclaration of Conformity in Languages of the European CommunityEnglish Hereby, SMC Networks, declares that this Radio LAN device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.Finnish Valmistaja SMC Networks vakuuttaa täten että Radio LAN device tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.Dutch Hierbij verklaart SMC Networks dat het toestel Radio LAN device in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EGBij deze SMC Networks dat deze Radio LAN device voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC.French Par la présente SMC Networks déclare que l'appareil Radio LAN device est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CESwedish Härmed intygar SMC Networks att denna Radio LAN device står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.Danish Undertegnede SMC Networks erklærer herved, at følgende udstyr Radio LAN device overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EFGerman Hiermit erklärt SMC Networks, dass sich dieser/diese/dieses Radio LAN device in Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befindet". (BMWi)Hiermit erklärt SMC Networks die Übereinstimmung des Gerätes Radio LAN device mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien)Greek

COMPLIANCESviDGT Statement of TaiwanItalian Con la presente SMC Networks dichiara che questo Radio LAN device è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.Spanish Por medio de la presente SMC Networks declara que el Radio LAN device cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CEPortuguese SMC Networks declara que este Radio LAN device está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE.注意！依據低功率電波輻射性電機管理辦法第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

COMPLIANCESviiSafety ComplianceUnderwriters Laboratories Compliance StatementImportant! Before making connections, make sure you have the correct cord set. Check it (read the label on the cable) against the following: The unit automatically matches the connected input voltage. Therefore, no additional adjustments are necessary when connecting it to any input voltage within the range marked on the power adapter.Information for Power Source This unit is to be used with a class 2 or level 3 external power adapter, approved suitable for use in North American equipment installation, having an output voltage rating of 12 V DC, and output current rating of 1.0 A or equivalent.Operating Voltage Cord Set Specifications120 Volts UL Listed/CSA Certified Cord SetMinimum 18 AWGType SVT or SJT three conductor cordMaximum length of 15 feetParallel blade, grounding type attachment plug rated 15 A, 125 V240 Volts (Europe only) Cord Set with H05VV-F cord having three conductors with minimum diameter of 0.75 mm2IEC-320 receptacleMale plug rated 10 A, 250 VN11846

ixTABLE OF CONTENTS1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1About the Barricade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2Hardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2ISP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5Connect the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6Connect the Cable/xDSL Modem . . . . . . . . . . . . . . . . . . . . . . . . 2-6Connecting the Barricade to your LAN . . . . . . . . . . . . . . . . . . . 2-6Connect the Power Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-73 Configuring the Client PC . . . . . . . . . . . . . . . . . . . . . . 3-1TCP/IP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2Windows 2000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3Obtain IP Settings From Your Barricade . . . . . . . . . . . . . . . . . . 3-5Manual IP Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9Disable HTTP Proxy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14Configuring Your Macintosh Computer . . . . . . . . . . . . . . . . . . . . . . . . 3-15Disable HTTP Proxy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-174 Configuring the Barricade . . . . . . . . . . . . . . . . . . . . . . 4-1Navigating the Web Browser Interface . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2Making Configuration Changes . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3Time Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4Connection Type Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12Time Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12Password Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13

TABLE OF CONTENTSxRemote Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14WAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15Dynamic IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16PPPoE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17PPTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18L2TP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19Static IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20Clone MAC Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21DNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-22LAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25Channel and SSID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-26Access Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-28Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29Wi-Fi Protected Setup (WPS) . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-36NAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-40Address Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-41Virtual Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-42Special Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-43NAT Mapping Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-44Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-45Static Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-45Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-49Access Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-50MAC Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-52URL Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-53Schedule Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-54Intrusion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-56DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-61UPnP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-62DDNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-63Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-64Configuration Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-64Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-65Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-66Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-67Finding the MAC address of a Network Card . . . . . . . . . . . . . . . . . . . 4-69

TABLE OF CONTENTSxiWindows NT4/2000/XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-69Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-69Linux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-69A Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .A-1B Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-1Ethernet Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1Wiring Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1RJ-45 Port Ethernet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3C Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-1

1-1CHAPTER 1INTRODUCTIONCongratulations on your purchase of the Barricade™ N Draft 11n Wireless 4-port Broadband Router (SMCWBR14S-N2). We are proud to provide you with a powerful yet simple communication device for connecting your local area network (LAN) to the Internet. For those who want to surf the Internet in the most secure way, this router provides a convenient and powerful solution.About the BarricadeThe Barricade provides Internet access to multiple users by sharing a single-user account. This new technology provides many secure and cost-effective functions. It is simple to configure and can be up and running in minutes.The Barricade is compliant with the next generation IEEE 802.11n draft v2.0 specification while maintaining full backwards compatibility with the IEEE 802.11b/g standards. This next generation wireless networking standard utilizes advanced MIMO (multiple-in, multiple-out) technology to deliver incredible speed and range. With wireless speeds up to 300Mbps - five times faster than 802.11g, the SMCWBR14S-N2 provides sufficient bandwidth to stream HD video, listen to digital music, play online games, transfer large files, make VoIP calls and surf the Internet simultaneously.

FEATURES AND BENEFITS1-2Features and Benefits• IEEE802.11n draft v2.0 compliant• Wireless speeds up to 300 Mbps• Increased speed and coverage - up to 15 times the speed of IEEE 802.11g• Fully backwards compatible with 802.11b/g wireless networks• Allows you to stream HD video, listen to digital music, play online games, transfer large files, make VoIP calls and surf the Internet simultaneously• Wi-Fi Multimedia (WMM) for wireless quality-of-service• Local network connection via a 10/100 Mbps Ethernet port• DHCP for dynamic IP configuration, and DNS for domain name mapping• Firewall with Stateful Packet Inspection, client privileges, intrusion detection, and NAT• NAT also enables multi-user Internet access via a single user account, and virtual server functionality (providing protected access to Internet services such as web, FTP, email, and Telnet)• VPN transparent pass-through (IPSec-ESP Tunnel mode, L2TP, PPTP)• User-definable application sensing tunnel supports applications requiring multiple connections• Easy setup through a web browser on any operating system that supports TCP/IP• Compatible with all popular Internet applications

INTRODUCTION1-3ApplicationsMany advanced networking features are provided by this Barricade:• Wired and Wireless LANThe Barricade provides connectivity to 10/100 Mbps devices, and wireless connection speed up to 300 Mbps. This router is fully compliant with specifications defined in IEEE 802.11b, IEEE 802.11g and IEEE 802.11n draft v2.0 standards, making it easy to create a network in small offices or homes.• Internet AccessThis device allows you to share your Cable/xDSL Internet connection. Since many ADSL providers use PPPoE to establish communications with end users, the Barricade includes a built-in client for this protocol, eliminating the need to install these services on your computer.• Shared IP AddressThe Barricade provides Internet access for up to 253 users via a single shared IP address. Using only one ISP account, multiple users on your network can browse the web at the same time.•Virtual ServerIf you have a fixed IP address, you can set the Barricade to act as a virtual host for network address translation. Remote users access various services at your site using a constant IP address. Then, depending on the requested service (or port number), the Barricade can route the request to the appropriate server (at another internal IP address). This secures your network from direct attack by hackers, and provides more flexible management by allowing you to change internal IP addresses without affecting outside access to your network.

APPLICATIONS1-4• DMZ Host SupportAllows a networked computer to be fully exposed to the Internet. This function is used when NAT and firewall security prevent an Internet application from functioning correctly.• SecurityThe Barricade supports security features that deny Internet access to specified users, or filter all requests for specific services that the administrator does not want to serve. The Barricade’s firewall also blocks common hacker attacks, including IP Spoofing, Land Attack, Ping of Death, IP with zero length, Smurf Attack, UDP port loopback, Snork Attack, TCP null scan, and TCP SYN flooding. WPA/WPA2, IEEE802.1x, WEP, SSID, and MAC filtering provide security over the wireless network.• Virtual Private Network (VPN Pass-through)The Barricade supports three of the most commonly used VPN protocols – PPTP, L2TP, and IPSec. These VPN protocols are transparent pass-through. The protocols supported by the Barricade are briefly described below.• Point-to-Point Tunneling Protocol – Provides a secure tunnel for remote client access to a PPTP security gateway. PPTP includes provisions for call origination and flow control required by ISPs.• L2TP merges the best features of PPTP and L2F – Like PPTP, L2TP requires that the ISP’s routers support the protocol.• IP Security – Provides IP network-layer encryption. IPSec can support large encryption networks (such as the Internet) by using digital certificates for device authentication.

2-1CHAPTER 2INSTALLATIONBefore installing the Barricade, verify that you have all the items listed under “Package Contents.” If any of the items are missing or damaged, contact your local distributor. Also be sure that you have all the necessary cabling before installing the Barricade. After installing the Barricade, refer to “Configuring the Barricade” on page 4-1.Package ContentsAfter unpacking the Barricade, check the contents of the box to be sure you have received the following components:• Barricade™ N Draft 11n Wireless 4-port Broadband Router (SMCWBR14S-N2)• Power adapter• One CAT-5 Ethernet cable (RJ-45)• One documentation CD•Quick Install Guide• Warranty Information CardImmediately inform your dealer in the event of any incorrect, missing, or damaged parts. If possible, please retain the carton and original packing materials in case there is a need to return the product.

INSTALLATION2-2System RequirementsYou must meet the following minimum requirements:• Broadband (Cable/xDSL) Internet service and Modem with Ethernet connection• 2.4GHz 802.11n draft wireless adapter or 2.4GHz 802.11b/g wireless adapter installed on each PC. Alternatively an Ethernet adapter can be used.• An up to date web browser: Internet Explorer 5.5 or above, Netscape 4.7 or above, Mozilla Firefox 1.0 or above.Hardware Description The Barricade connects to a cable or xDSL modem with Ethernet connection using it’s RJ-45 WAN port. It can be connected directly to your PC or to a local area network using the Fast Ethernet LAN ports.Data passing between devices connected to your local area network can run at up to 100 Mbps over the Fast Ethernet port and up to 300 Mbps over the built-in wireless access point. The Barricade includes an LED display on the top panel for system power and port indications that simplifies installation and network troubleshooting.

HARDWARE DESCRIPTION2-3The following figures show the top and rear panels of the Barricade.Figure 2-1. Top Panel Figure 2-2. Rear Panel9V 1A

INSTALLATION2-4The power and port LED indicators on the top panel are illustrated by the following table. LED Status DescriptionPower On The Barricade is receiving power. Normal operation.Off Power off or failure.WAN On WAN link.Off No WAN link.Online On Internet connection is functioning correctly.Flashing The Barricade is establishing an Internet link.Off No Internet link.WLAN On WLAN link.Flashing The Barricade is sending or receiving data via WLAN.Off No WLAN link.LAN 1~4 On Ethernet link.Flashing The LAN port is sending or receiving data.Off No Ethernet link.WPS (Wi-Fi Protected Setup)On WPS link is successfully established.Off • This LED will be on for 300 seconds after WPS connection is successfully established, then go off.• The WPS is disabled.Slow FlashingWPS association is establishing between the Barricade and clients.Quick FlashingWPS access failed.

ISP SETTINGS2-5The Barricade contains the following ports and buttons:ISP SettingsIf you are not sure of your connection method, please contact your Internet Service Provider. There are several connection types to choose from: Static IP, DHCP, PPPoE, PPTP and L2TP. Note: If using the PPPoE option, you will need to remove or disable any PPPoE client software on your computers. Item DescriptionLAN Ports Fast Ethernet ports (RJ-45). Connect devices on your local area network to these ports (i.e., a PC, hub, switch or IP set top box).WAN Port WAN port (RJ-45). Connect your cable/xDSL modem line to this port.Reset Button Use this button to reset the power and restore the default factory settings. To reset without losing configuration settings, see “Reset” on page 4-66.Power Inlet Connect the included power adapter to this inlet.Warning: Using the wrong type of power adapter may cause damage.WPS Button (on top panel)Press this button for over 4 seconds to start using the WPS.

INSTALLATION2-6Connect the SystemThe Barricade can be positioned at any convenient location in your office or home. No special wiring or cooling requirements are needed. You should, however, comply with the following guidelines:• Keep the Barricade away from any heating devices.• Do not place the Barricade in a dusty or wet environment.You should also remember to turn off the power, remove the power cord from the outlet, and keep your hands dry when you install the Barricade.Connect the Cable/xDSL Modem Connect the cable/xDSL modem using a CAT-5 Ethernet cable (RJ-45) to the Barricade’s WAN port. When inserting the RJ-45 plug, be sure the tab on the plug clicks into position to ensure it is properly seated.Connecting the Barricade to your LANThe four LAN ports on the Barricade auto-negotiate the connection speed to 10 Mbps Ethernet or 100 Mbps Fast Ethernet, as well as the transmission mode to half duplex or full duplex.Use RJ-45 cables to connect any of the four LAN ports on the Barricade to an Ethernet adapter on your PC. Otherwise, cascade any of the LAN ports on the Barricade to an Ethernet hub or switch, and then connect your PC or other network equipment to the hub or switch. When inserting an RJ-45 connector, be sure the tab on the connector clicks into position to ensure that it is properly seated.Notes: 1. Use 100-ohm shielded or unshielded twisted-pair cable with RJ-45 connectors for all Ethernet ports. Use Category 3, 4, or 5 for connections that operate at 10 Mbps, and Category 5 for connections that operate at 100 Mbps.2. Make sure each twisted-pair cable length does not exceed 100 meters (328 feet).

CONNECT THE SYSTEM2-7Connect the Power AdapterPlug the power adapter into the power socket on the back panel of the Barricade, and the other end into a power outlet.Check the power indicator on the front panel is lit. If the power indicator is not lit, refer to “Troubleshooting” on page A-1.In case of a power input failure, the Barricade will automatically restart and begin to operate once the input power is restored.

INSTALLATION2-8

3-1CHAPTER 3CONFIGURING THECLIENT PCAfter completing hardware setup by connecting all your network devices, you need to configure your computer to connect to the Barricade. You can either configure your computer to automatically obtain IP settings (DHCP) or manually configure IP address settings (Static IP).Depending on your operating system see:“Windows 2000” on page 3-3,“Windows XP” on page 3-9,or“Configuring Your Macintosh Computer” on page 3-15.

TCP/IP CONFIGURATION3-2TCP/IP ConfigurationTo access the Internet through the Barricade, you must configure the network settings of the computers on your LAN to use the same IP subnet as the Barricade. The default network settings for the Barricade are:IP Address: 192.168.2.1 Subnet Mask: 255.255.255.0Note: These settings can be changed to fit your network requirements, but you must first configure at least one computer to access the Barricade’s web configuration interface in order to make the required changes. (See “Configuring the Barricade” on page 4-1 for instructions on configuring the Barricade.)

CONFIGURING THE CLIENT PC3-3Windows 2000DHCP IP Configuration1. On the Windows desktop, click Start/Settings/Network and Dial-Up Connections. 2. Click the icon that corresponds to the connection to your Barricade.3. The connection status screen will open. Click Properties.

TCP/IP CONFIGURATION3-44. Double-click Internet Protocol (TCP/IP).5. If Obtain an IP address automatically and Obtain DNS server address automatically are already selected, your computer is already configured for DHCP. If not, select these options now and click OK.

CONFIGURING THE CLIENT PC3-5Obtain IP Settings From Your BarricadeNow that you have configured your computer to connect to your Barricade, it needs to obtain new network settings. By releasing old DHCP IP settings and renewing them with settings from your Barricade, you can verify that you have configured your computer correctly.1. On the Windows desktop, click Start/Programs/Accessories/Command Prompt.2. In the Command Prompt window, type ipconfig /release and press the Enter key.

TCP/IP CONFIGURATION3-63. Type ipconfig /renew and press the Enter key. Verify that your IP Address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.2.1. These values confirm that your Barricade is functioning correctly.4. Type exit and press the Enter key to close the Command Prompt window.

CONFIGURING THE CLIENT PC3-7Manual IP Configuration1. Follow steps 1-4 in “DHCP IP Configuration” on page 3-3.2. Select Use the following IP address. Enter an IP address based on the default network 192.168.2.x (where x is between 2 and 254), and use 255.255.255.0 for the subnet mask. Use 192.168.2.1 for the Default gateway field.3. Select Use the following DNS server addresses.4.Enter the IP address for the Barricade in the Preferred DNS server field. This automatically relays DNS requests to the DNS server(s) provided by your ISP. Otherwise, add a specific DNS server into the Alternate DNS Server field and click OK to close the dialog boxes.5. Record the configured information in the following table.TCP/IP Configuration SettingIP Address ____.____.____.____Subnet Mask ____.____.____.____Preferred DNS Server ____.____.____.____Alternate DNS Server ____.____.____.____Default Gateway ____.____.____.____

TCP/IP CONFIGURATION3-8Disable HTTP ProxyYou need to verify that the “HTTP Proxy” feature of your web browser is disabled. This is so that your browser can view the Barricade’s HTML configuration pages.1. To disable the proxy in Internet Explorer, click Tools. Click Internet Options... and then the Connections tab, shown on the right. In the Local Area Network (LAN) settings section, click LAN Settings... to display the Local Area Network (LAN) Settings pop-up window below.2. In the Proxy server section, ensure the Use a proxy server for your LAN (These settings will not apply to dial-up or VPN connections) check box is not ticked.3. Click OK.

CONFIGURING THE CLIENT PC3-9Windows XPDHCP IP Configuration1. On the Windows desktop, click Start/Control Panel.2. In the Control Panel window, click Network and Internet Connections.3. The Network Connections window will open. Locate and double-click the Local Area Connection icon for the Ethernet adapter that is connected to the Barricade.4. In the connection status screen, click Properties.

TCP/IP CONFIGURATION3-105. Double-click Internet Protocol (TCP/IP).6. If Obtain an IP address automatically and Obtain DNS server address automatically are already selected, your computer is already configured for DHCP. If not, select these options now and click OK.

CONFIGURING THE CLIENT PC3-11Obtain IP Settings From Your BarricadeNow that you have configured your computer to connect to your Barricade, it needs to obtain new network settings. By releasing old DHCP IP settings and renewing them with settings from your Barricade, you can verify that you have configured your computer correctly.1. On the Windows desktop, click Start/Programs/Accessories/Command Prompt.2. In the Command Prompt window, type ipconfig /release and press the Enter key.

TCP/IP CONFIGURATION3-123. Type ipconfig /renew and press the Enter key. Verify that your IP Address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.2.1. These values confirm that your Barricade is functioning correctly.4. Type exit and press the Enter key to close the Command Prompt window.Your computer is now configured to connect to the Barricade.

CONFIGURING THE CLIENT PC3-13Manual IP Configuration1. Follow steps 1-5 in “DHCP IP Configuration” on page 3-9.2. Select Use the following IP Address.3. Enter an IP address based on the default network 192.168.2.x (where x is between 2 and 254), and use 255.255.255.0 for the subnet mask. Use 192.168.2.1 for the Default gateway field.4. Select Use the following DNS server addresses.5. Enter the IP address for the Barricade in the Preferred DNS server field. This automatically relays DNS requests to the DNS server(s) provided by your ISP. Otherwise, add a specific DNS server into the Alternate DNS Server field and click OK to close the dialog boxes.6. Record the configured information in the following table.TCP/IP Configuration SettingIP Address ____.____.____.____Subnet Mask ____.____.____.____Preferred DNS Server ____.____.____.____Alternate DNS Server ____.____.____.____Default Gateway ____.____.____.____

TCP/IP CONFIGURATION3-14Disable HTTP ProxyYou need to verify that the “HTTP Proxy” feature of your web browser is disabled. This is so that your browser can view the Barricade’s HTML configuration pages.1. To disable the proxy in Internet Explorer, click Tools. Click Internet Options... and then the Connections tab, shown on the right. In the Local Area Network (LAN) settings section, click LAN Settings... to display the Local Area Network (LAN) Settings pop-up window below.2. In the Proxy server section, ensure the Use a proxy server for your LAN (These settings will not apply to dial-up or VPN connections) check box is not ticked.3. Click OK.

CONFIGURING THE CLIENT PC3-15Configuring Your Macintosh ComputerYou may find that the instructions here do not exactly match your operating system. This is because these steps and screen shots were created using Mac OS 10.2. Mac OS 7.x and above are similar, but may not be identical to Mac OS 10.2.Follow these instructions:1. Pull down the Apple Menu . Click System Preferences.2. Double-click the Network icon in the Systems Preferences window.

CONFIGURING YOUR MACINTOSH COMPUTER3-163. If Using DHCP Server is already selected in the Configure field, your computer is already configured for DHCP. If not, select this option.4. Your new settings are shown in the TCP/IP tab. Verify that your IP Address is now 192.168.2.xxx, your Subnet Mask is 255.255.255.0 and your Default Gateway is 192.168.2.1. These values confirm that your Barricade is functioning.5. Close the Network window.Now your computer is configured to connect to the Barricade.

CONFIGURING THE CLIENT PC3-17Disable HTTP ProxyYou need to verify that the “HTTP Proxy” feature of your web browser is disabled. This is so that your browser can view the Barricade’s HTML configuration pages. The following steps are for Internet Explorer.Internet Explorer1. Open Internet Explorer and click the Stop button. Click Explorer/Preferences.2. In the Internet Explorer Preferences window, under Network, select Proxies.3. Uncheck all check boxes and click OK.

CONFIGURING YOUR MACINTOSH COMPUTER3-18

4-1CHAPTER 4CONFIGURING THEBARRICADEAfter you have configured TCP/IP on a client computer, use a web browser to configure the Barricade. The Barricade can be configured by any Java-supported browser such as Internet Explorer 5.5 or above. Using the web management interface, you can configure the Barricade and view statistics to monitor network activity.To access the Barricade’s management interface, enter the IP address of the Barricade in your web browser: http://192.168.2.1. Enter the default password: smcadmin, and click LOGIN.Notes: 1 Passwords can contain from 3~12 alphanumeric characters and are case sensitive.2You might click the language selection at the top right corner of the screen for your regional location before accessing the management interface.

CONFIGURING THE BARRICADE4-2Navigating the Web Browser InterfaceThe Barricade’s management interface consists of a Setup Wizard and an Advanced Settings section.Setup Wizard: Use the Setup Wizard for quick and easy configuration of your Internet connection and basic LAN settings.Advanced Settings: Advanced Settings supports more advanced functions like NAT, system maintenance, firewall and UPnP. Making Configuration ChangesConfigurable parameters have a dialog box or a drop-down list. Once a configuration change has been made on a screen, click the APPLY or SAVE SETTINGS or NEXT button at the bottom of the screen to enable the new setting.Note: To ensure proper screen refresh after a command entry, be sure that Internet Explorer is configured as follows: Under the menu Tools/Internet Options/General/Temporary Internet Files/Settings, the setting for Check for newer versions of stored pages should be Every visit to the page.

SETUP WIZARD4-3Setup WizardTime ZoneClick on SETUP WIZARD and NEXT, then you will see the Time Zone screen. Select your local time zone from the drop-down menu. This information is used for log entries and client filtering.If you want to automatically synchronize the Barricade with a public time server, check the box to Enable Automatic Time Server Maintenance. Select the desired servers from the drop-down menus.Click NEXT to continue.

CONFIGURING THE BARRICADE4-4Wireless SettingsThis screen allows you to configure the SSID, wireless Mode and channel. Optionally you can disable broadcasting of SSID for added security. SSID is the name given to your wireless LAN. Wireless clients within the same network should be configured to use the same SSID.Parameter DescriptionWireless Channel The radio channel used by the wireless router and its clients to communicate with each other. This channel must be the same on the Barricade and all of its wireless clients.The Barricade will automatically assign itself a radio channel, or you may select one manually.Extension ChannelSetting the Bandwith Mode as 20/40MHz allows you to use this extension channel as the secondary channel for doubling the bandwith of your wireless network.SSID Service Set ID. The SSID must be the same on the Barricade and all of its wireless clients. (Default: SMC)Wireless Mode This device supports 11n, 11g and 11b wireless networks. Make your selection depending on the type of wireless network that you have. SMC recommend using “Mixed 802.11n, 802.11g and 802.11b” to provide compatibility with 11n, 11g and 11b wireless clients.

SETUP WIZARD4-5Click NEXT to continue. Bandwidth • 20MHz: Sets the operation bandwidth as 20 MHz.• 20/40MHz: Allows automatic detection of the operation bandwidth between 20 MHz and 40 MHz. Choosing the bandwidth mode as 20/40MHz allows you to use the extension channel.Broadcast SSID Enable or disable the broadcasting of the SSID. Disabling SSID broadcast will provide increased security by hiding the SSID of your wireless network.Protected Mode Enabling this function to ensure the best performance of your 11n throughput in case there is a lot of interference from the 11g and 11b devices in the wireless network.802.11e/WMM QoSEnable or disable the use of QoS. The QoS (Quality of Service) function allows you to differentiate WMM (Wi-Fi Multimedia) traffic and provide it with high-priority forwarding serviceParameter Description

CONFIGURING THE BARRICADE4-6Connection Type SettingSpecify the WAN connection type required by your Internet Service Provider. Specify Dynamic IP Address, PPPoE, PPTP, L2TP or Static IP Address.Select your connection type to proceed. Click BACK to go back and change your settings.

SETUP WIZARD4-7Dynamic IP AddressIf the ISP requires you to input a Host Name, type it in the Host Name field. Click on the Clone the MAC Address and the MAC Address of the current PC will be filled automatically.Click NEXT to proceed, or BACK to change your settings.

CONFIGURING THE BARRICADE4-8PPPoEEnter the User Name and Password required by your ISP in the appropriate fields. If your ISP has provided you with a Service Name enter it in the Service Name field, otherwise, leave it blank. Leave the Maximum Transmission Unit (MTU) at the default value (1454) unless you have a particular reason to change it. Enter the maximum idle time for the Internet connection. After this time has been exceeded the connection will be terminated. Check the Auto-reconnect check box to automatically re-establish the connection as soon as you attempt to access the Internet again.Click NEXT to proceed, or BACK to change your settings.Note: Clicking NEXT will not automatically connect the Barricade to the Internet. The Barricade will only connect when you explicitly request it to, for example, by launching your web browser.

SETUP WIZARD4-9PPTP (Point-to-Point Tunneling Protocol)The Barricade supports PPTP connection. The PPTP connection delivers user-level authentication VPN (virtual private network) for secure network path.Enter the user account ID and password required by your ISP in the appropriate fields. If your ISP has provided you with a Host Name enter it in the Host Name field, otherwise, leave it blank. If your ISP uses DHCP service, enable the Get IP by DHCP. Then enter the Service IP Address provided by your ISP.Click on the Disconnect after x minutes of no activity and then enter the idle time for the Internet connection. This is the period of time for which the connection to the Internet is maintained during inactivity. If your ISP charges you by the minute, you should change the idle time out to one minute. Most ISPs provide a DNS server for speed and convenience. Since your Service Provider may connect to the Internet with dynamic IP settings, it is likely that the DNS server IP’s are also provided dynamically. Clicking on the Click here to enter your DNS Settings for DNS configuration. See “DNS” on page 4-22.Click NEXT to proceed, or BACK to change your settings.

CONFIGURING THE BARRICADE4-10L2TP (Layer 2 Tunneling Protocol) The Barricade supports L2TP connection. The L2TP connection delivers computer-level authentication VPN (virtual private network) for secure network path.Enter the user account ID and password required by your ISP in the appropriate fields. If your ISP uses DHCP service, enable the Get IP by DHCP. Then enter the L2TP Server Address provided by your ISP.Click on the Disconnect after x minutes of no activity and then enter the idle time for the Internet connection. This is the period of time for which the connection to the Internet is maintained during inactivity. If your ISP charges you by the minute, you should change the idle time out to one minute. Most ISPs provide a DNS server for speed and convenience. Since your Service Provider may connect to the Internet with dynamic IP settings, it is likely that the DNS server IP’s are also provided dynamically. Clicking on the Click here to enter your DNS Settings for DNS configuration. See “DNS” on page 4-22.Click NEXT to proceed, or BACK to change your settings.

SETUP WIZARD4-11Static IP AddressEnter the IP address, Subnet Mask and Gateway Address provided to you by your ISP in the appropriate fields below.Click NEXT to proceed, or BACK to change your settings.

CONFIGURING THE BARRICADE4-12SystemTime ZoneSelect your local time zone from the drop-down list. This information is used for log entries and client filtering.For accurate timing of log entries and system events, you need to set the time zone. Select your time zone from the drop-down list.If daylight savings is used in your area, check the box to enable the function, and select the start/end dates.If you want to automatically synchronize the Barricade with a public time server, check the box to Enable Automatic Time Server Maintenance. Select the desired servers from the drop-down menu.Click SAVE SETTINGS.

SYSTEM4-13Password SettingsUse this screen to change the password for accessing the management interface. Passwords can contain from 3~12 alphanumeric characters and are case sensitive.Note: If you lost the password, or you cannot gain access to the user interface, press the blue reset button on the rear panel, holding it down for at least 10 seconds to restore the factory defaults. The default password is smcadmin.Enter a maximum Idle Time Out (in minutes) to define a maximum period of time for which the login session is maintained during inactivity. If the connection is inactive for longer than the maximum idle time, it will perform system logout, and you have to log in again to access the management interface. (Default: 10 minutes)

CONFIGURING THE BARRICADE4-14Remote ManagementBy default, management access is only available to users on your local network. However, you can also manage the Barricade from a remote host by entering the IP address of a remote computer on this screen. Check the Enabled check box, and enter the IP address of the Host Address and click SAVE SETTINGS. Note: If you check Enable and specify an IP address of 0.0.0.0, any remote host can manage the Barricade.For remote management via WAN IP address you need to connect using port 8080. Simply enter WAN IP address followed by :8080, for example, 211.20.16.1:8080.

WAN SETTINGS4-15WAN SettingsSpecify the WAN connection type required by your Internet Service Provider. Choose Dynamic IP Address, PPPoE, PPTP, L2TP or Static IP Address for your WAN link. Select the connection type and click More Configuration.

CONFIGURING THE BARRICADE4-16Dynamic IPThe Host Name is optional, but may be required by some service provider’s. The default MAC address is set to the WAN’s physical interface on the Barricade.If required by your service provider, you can use the Clone MAC Address button to copy the MAC address of the Network Interface Card (NIC) installed in your PC to replace the WAN MAC address.If necessary, you can use the Renew button on the Status page to renew the WAN IP address.Note: Make sure you record the MAC address that you clone, so that if you lose your settings you will be able to re-connect to the Internet.Click SAVE SETTINGS to proceed, or CANCEL to change your settings.

WAN SETTINGS4-17PPPoEEnter the PPPoE user name and password assigned by your Service Provider. The Service Name is normally optional, but may be required by some service providers. Enter a Maximum Idle Time (in minutes) to define a maximum period of time for which the Internet connection is maintained during inactivity. If the connection is inactive for longer than the Maximum Idle Time, then it will be dropped. You can enable the Auto-reconnect option to automatically re-establish the connection as soon as you attempt to access the Internet again.Click SAVE SETTINGS to proceed, or CANCEL to change your settings.

CONFIGURING THE BARRICADE4-18PPTPEnter the Account ID and Password, and Host Name assigned by your ISP in the appropriate fields. If your ISP uses DHCP service, enable the Get IP by DHCP. Then enter the Service IP Address provided by your ISP. Click on the Disconnect after x minutes of no activity and then enter the idle time for the Internet connection. This is the period of time for which the connection to the Internet is maintained during inactivity. If your ISP charges you by the minute, you should change the idle time out to one minute. Most ISPs provide a DNS server for speed and convenience. Since your Service Provider may connect to the Internet with dynamic IP settings, it is likely that the DNS server IP’s are also provided dynamically. Clicking on the Click here to enter your DNS Settings for DNS configuration. See “DNS” on page 4-22.Click SAVE SETTINGS to proceed, or Clear to change your settings.

WAN SETTINGS4-19L2TPEnter the L2TP Account ID and Password assigned by your ISP in the appropriate fields. If your ISP uses DHCP service, enable the Get IP by DHCP. Then enter the L2TP Server Address provided by your ISP. Click on the Disconnect after x minutes of no activity and then enter the idle time for the Internet connection. This is the period of time for which the connection to the Internet is maintained during inactivity. If your ISP charges you by the minute, you should change the idle time out to one minute. Most ISPs provide a DNS server for speed and convenience. Since your Service Provider may connect to the Internet with dynamic IP settings, it is likely that the DNS server IP’s are also provided dynamically. Clicking on the Click here to enter your DNS Settings for DNS configuration. See “DNS” on page 4-22.Click SAVE SETTINGS to proceed, or Clear to change your settings.

CONFIGURING THE BARRICADE4-20Static IPIf your Service Provider has assigned a fixed IP address, enter the assigned IP address, subnet mask and the gateway address on this screen.Click SAVE SETTINGS to proceed, or CANCEL to change your settings.

WAN SETTINGS4-21Clone MAC AddressSome ISPs require you to register your MAC address with them. If this is the case, and you have previously registered the MAC address of another device, the MAC address of the Barricade must be changed to the MAC address that you have registered with your ISP.

CONFIGURING THE BARRICADE4-22DNSA Domain Name Server (DNS) is an index of IP addresses and web addresses. If you type a web address into your browser, such as www.smc.com, a DNS server will find that name in its index and find the matching IP address: xxx.xxx.xxx.xxx. Most ISPs provide a DNS server for speed and convenience. Since your Service Provider may connect to the Internet with dynamic IP settings, it is likely that the DNS server IP’s are also provided dynamically. However, if there is a DNS server that you would rather use, you need to specify the IP address here.

LAN SETTINGS4-23LAN SettingsYou can enable DHCP to dynamically allocate IP addresses to your client PCs, or configure filtering functions based on specific clients or protocols. The Barricade must have an IP address for the local network.The LAN Settings parameters are listed below.Parameter DescriptionLAN IPIP Address The IP address of the Barricade.IP Subnet Mask The IP subnet mask.DHCP Server DHCP allows individual computers to obtain the TCP/IP configuration at startup from a centralized DHCP server. To dynamically assign an IP address to a client PC, enable the DHCP (Dynamic Host Configuration Protocol) function.

CONFIGURING THE BARRICADE4-24Lease Time The length of time the DHCP server will reserve the IP address for each computer. Setting lease times for shorter intervals such as one day or one hour frees IP addresses after the specified period of time. This also means that a particular computer’s IP address may change over time. If you have set any advanced features such as DMZ, this is dependent on the IP address. For this reason, you will not want the IP address to change.IP Address Pool The DHCP IP Address Pool is the range of IP addresses set aside for dynamic assignment to the computers on your network.Start IP This field indicates the first of the contiguous IP addresses in the IP address pool.End IP This field indicates the last of the contiguous IP addresses in the IP address pool.Domain Name The domain name is the name you assign to your network.Parameter Description

WIRELESS4-25WirelessThe Barricade also operates as a wireless access point, allowing wireless computers to communicate with each other. To configure this function, all you need to do is to enable the wireless function, define the radio channel, the SSID, and the security options. Check Enable and click SAVE SETTINGS.

CONFIGURING THE BARRICADE4-26Channel and SSIDYou must specify a common radio channel and SSID (Service Set ID) to be used by the Barricade and all of its wireless clients. Be sure you configure all of its clients to the same values. Parameter DescriptionWireless Channel The radio channel used by the wireless router and its clients to communicate with each other. This channel must be the same on the Barricade and all of its wireless clients.The Barricade will automatically assign itself a radio channel, or you may select one manually.Extension ChannelSetting the Bandwith Mode as 20/40MHz allows you to use this extension channel as the secondary channel for doubling the bandwith of your wireless network.SSID Service Set ID. The SSID must be the same on the Barricade and all of its wireless clients. (Default: SMC)Wireless Mode This device supports 11n, 11g and 11b wireless networks. Make your selection depending on the type of wireless network that you have. SMC recommend using “Mixed 802.11n, 802.11g and 802.11b” to provide compatibility with 11n, 11g and 11b wireless clients.

WIRELESS4-27Bandwidth • 20MHz: Sets the operation bandwidth as 20 MHz.• 20/40MHz: Allows automatic detection of the operation bandwidth between 20 MHz and 40 MHz. Choosing the bandwidth mode as 20/40MHz allows you to use the extension channel.Broadcast SSID Enable or disable the broadcasting of the SSID. Disabling SSID broadcast will provide increased security by hiding the SSID of your wireless network.Protected Mode Enabling this function to ensure the best performance of your 11n throughput in case there is a lot of interference from the 11g and 11b devices in the wireless network.802.11e/WMM QoSEnable or disable the use of QoS. The QoS (Quality of Service) function allows you to differentiate WMM (Wi-Fi Multimedia) traffic and provide it with high-priority forwarding serviceParameter Description

CONFIGURING THE BARRICADE4-28Access ControlUsing the Access Control functionality, you can restrict access based on MAC address. Each PC has a unique identifier known as a Medium Access Control (MAC) address. With MAC filtering enabled, the computers whose MAC address you have listed in the filtering table will be able to connect (or will be denied access) to the Barricade.

WIRELESS4-29SecurityTo make your wireless network safe, you should turn on the security function. The Barricade supports the following security mechanism:•WEP•WPA

CONFIGURING THE BARRICADE4-30WEPIf you want to use WEP to protect your wireless network, you need to set the same parameters for the Barricade and all your wireless clients.To generate the key automatically with passphrase, enter a string of characters and click the GENERATE button. Select the default key from the drop-down menu. Click SAVE SETTINGS. Note: The passphrase can consist of up to 32 alphanumeric characters.To manually configure the encryption key, enter five hexadecimal pairs of digits for the 64-bit key, or enter 13 pairs for the 128-bit key. (A hexadecimal digit is a number or letter in the range 0-9 or A-F.)Note: WEP protects data transmitted between wireless nodes, but does not protect any transmissions over your wired network or over the Internet.Parameter DescriptionWEP Mode Select 64 bit or 128 bit key to use for encryption.Key Entry Method Select Hex or ASCII to use for encryption key.Static WEP Key SettingYou may automatically generate encryption keys or manually enter the keys.

WIRELESS4-31WPAWi-Fi Protected Access (WPA) combines temporal key integrity protocol (TKIP) and 802.1X mechanisms. It provides dynamic key encryption and 802.1X authentication service. Parameter DescriptionAuthentication Choose 802.1X or Pre-shared Key to use as the authentication method. • 802.1X: for the enterprise network with a RADIUS server. See “802.1X” on page 4-34.• Pre-shared key: for the SOHO network environment without an authentication server. Pre-shared key type Select the key type to be used in the Pre-shared Key. Pre-shared Key Type in the key here.

CONFIGURING THE BARRICADE4-32WPA2WPA2 is a product certification that is available through the Wi-Fi Alliance. WPA2 certifies that wireless equipment is compatible with the IEEE 802.11i standard. The WPA2 product certification formally replaces Wired Equivalent Privacy (WEP) and the other security features of the original IEEE 802.11 standard. The goal of WPA2 certification is to support the additional mandatory security features of the IEEE 802.11i standard that are not already included for products that support WPA. Parameter DescriptionAuthentication Choose 802.1X or Pre-shared Key to use as the authentication method. • 802.1X: for the enterprise network with a RADIUS server. See “802.1X” on page 4-34.• Pre-shared key: for the SOHO network environment without an authentication server. Pre-shared key type Select the key type to be used in the Pre-shared Key. Pre-shared Key Type in the key here.

WIRELESS4-33WPA+WPA2Wi-Fi Protected Access (WPA) combines temporal key integrity protocol (TKIP) and 802.1x mechanisms. It provides dynamic key encryption and 802.1x authentication service. Wi-Fi Protected Access 2 (WPA2) is a product certification that is available through the Wi-Fi Alliance. WPA2 certifies that wireless equipment is compatible with the IEEE 802.11i standard. The WPA2 product certification formally replaces Wired Equivalent Privacy (WEP) and the other security features of the original IEEE 802.11 standard. The goal of WPA2 certification is to support the additional mandatory security features of the IEEE 802.11i standard that are not already included for products that support WPA.

CONFIGURING THE BARRICADE4-34802.1XIf 802.1X is used in your network, then you should enable this function for the Barricade.Parameter DescriptionAuthentication Choose 802.1X or Pre-shared Key to use as the authentication method. • 802.1X: for the enterprise network with a RADIUS server. See “802.1X” on page 4-34.• Pre-shared key: for the SOHO network environment without an authentication server. Pre-shared key type Select the key type to be used in the Pre-shared Key. Pre-shared Key Type in the key here.

WIRELESS4-35Parameter DescriptionAuthentication Enable 802.1X authentication. Session Idle TimeoutDefines a maximum period of time for which the connection is maintained during inactivity.Re-Authentication PeriodDefines a maximum period of time for which the authentication server will dynamically re-assign a session key to a connected client.Quiet Period Defines a maximum period of time for which the ADSL Router will wait between failed authentications. Server Type The Server Type of your authentication server is RADIUS. RADIUS Server ParametersServer IP The IP address of your authentication server. Server Port The port used for the authentication service. Secret Key The secret key shared between the authentication server and its clients.NAS-ID Defines the request identifier of the Network Access Server.

CONFIGURING THE BARRICADE4-36Wi-Fi Protected Setup (WPS)The Barricade was implemented with the ease-of-use Wi-Fi Protected Setup (WPS). WPS makes a secure wireless network much easier to achieve by using an eight-digit PIN number and the Push Button Control (PBC).Check Enable and click Apply Changes.Pressing Generate New PIN creates a new Current PIN number.Pressing Restore Default PIN sets the PIN code to the factory default number. Take the following steps for easy network security settings.

WIRELESS4-37PIN Code Setup1. Power on your client device supporting WPS PIN code method.2. Start WPS PIN process on client device. For instructions on how to do this refer to the user manual of the client device.3. Enter the PIN code of client device. Note: The PIN code is generally printed on the bottom of the unit or displayed in the configuration utility.4. Click the Start PIN button on the screen.

CONFIGURING THE BARRICADE4-38Push Button Configuration (PBC) MethodTo achieve successful WPS connection, you can use one of the following ways: (1) push and hold the WPS button on your Barricade, or (2) click the Start PBC button on this screen.1. Power on your network devices such as an access point and client network devices.2. Press the WPS button for 4 seconds, or click the Start PBC button on the screen.3. Press the WPS button or click the PBC button on your client devices of your network.Note: This connection procedure must be done within 2 minutes after pressing the WPS button on the Barricade.

WIRELESS4-39ManualFor client devices without WPS, manually configure the device as displayed on the screen.

CONFIGURING THE BARRICADE4-40NATNetwork Address Translation allows multiple users to access the Internet sharing one public IP.

NAT4-41Address MappingAllows one or more public IP addresses to be shared by multiple internal users. This also hides the internal network for increased privacy and security. Enter the Public IP address you wish to share into the Global IP field. Enter a range of internal IPs that will share the global IP into the “from” field.

CONFIGURING THE BARRICADE4-42Virtual ServerIf you configure the Barricade as a virtual server, remote users accessing services such as web or FTP at your local site via public IP addresses can be automatically redirected to local servers configured with private IP addresses. In other words, depending on the requested service (TCP/UDP port number), the Barricade redirects the external service request to the appropriate server (located at another internal IP address). For example, if you set Type/Public Port to TCP/80 (HTTP or web) and the Private IP/Port to 192.168.2.2/80, then all HTTP requests from outside users will be transferred to 192.168.2.2 on port 80. Therefore, by just entering the IP address provided by the ISP, Internet users can access the service they need at the local address to which you redirect them. The more common TCP service ports include: HTTP: 80, FTP: 21, Telnet: 23, and POP3: 110. A list of ports is maintained at the following link: http://www.iana.org/assignments/port-numbers.

NAT4-43Special Application Some applications require multiple connections, such as Internet gaming, video-conferencing, and Internet telephony. These applications may not work when Network Address Translation (NAT) is enabled. If you need to run applications that require multiple connections, use these screens to specify the additional public ports to be opened for each application.

CONFIGURING THE BARRICADE4-44NAT Mapping Table This screen displays the current NAPT (Network Address Port Translation) address mappings. NAT Mapping Table displays the current NAPT address mappings. The NAT address mappings are listed 20 lines per page, click the control buttons to move forwards and backwards. As the NAT mapping is dynamic, a Refresh button is provided to refresh the NAT Mapping Table with the mots updated values.The content of the NAT Mapping Table is described as follows.• Protocol - protocol of the flow. • Local IP - local (LAN) host’s IP address for the flow. • Local Port - local (LAN) host’s port number for the flow. •Pseudo IP - translated IP address for the flow. • Pseudo Port - translated port number for the flow. • Peer IP - remote (WAN) host’s IP address for the flow. • Peer Port - remote (WAN) host’s port number for the flow.

ROUTING4-45RoutingThese screens define routing related parameters, including static routes and RIP (Routing Information Protocol) parameters.Static Route Click Add to add a new static route to the list, or check the box of an already entered route and click Modify. Clicking Delete will remove an entry from the list.Parameter DescriptionIndex Check the box of the route you wish to delete or modify.Network Address Enter the IP address of the remote computer for which to set a static route.Subnet Mask Enter the subnet mask of the remote network for which to set a static route.Gateway Enter the WAN IP address of the gateway to the remote network.

CONFIGURING THE BARRICADE4-46RIPRIP sends routing-update messages at regular intervals and when the network topology changes. When a router receives a routing update that includes changes to an entry, it updates its routing table to reflect the new route. RIP routers maintain only the best route to a destination. After updating its routing table, the router immediately begins transmitting routing updates to inform other network routers of the change.

ROUTING4-47Parameter DescriptionGeneral RIP ParametersRIP mode Globally enables or disables RIP.Auto summary If Auto summary is disabled, then RIP packets will include sub-network information from all sub-networks connected to the router. If enabled, this sub-network information will be summarized to one piece of information covering all sub-networks. Table of current Interface RIP parameterInterface The WAN interface to be configured.Operation Mode Disable: RIP disabled on this interface.Enable: RIP enabled on this interface.Silent: Listens for route broadcasts and updates its route table. It does not participate in sending route broadcasts.Version Sets the RIP (Routing Information Protocol) version to use on this interface. Poison Reverse A method for preventing loops that would cause endless retransmission of data traffic.Authentication Required • None: No authentication. • Password: A password authentication key is included in the packet. If this does not match what is expected, the packet will be discarded. This method provides very little security as it is possible to learn the authentication key by watching RIP packets.Authentication Code Password Authentication key.

CONFIGURING THE BARRICADE4-48Routing Table Parameter DescriptionFlags Indicates the route status: C = Direct connection on the same subnet.S = Static route.R = RIP (Routing Information Protocol) assigned route.I = ICMP (Internet Control Message Protocol) Redirect route.Network Address Destination IP address.Netmask The subnetwork associated with the destination.This is a template that identifies the address bits in the destination address used for routing to specific subnets. Each bit that corresponds to a “1” is part of the subnet mask number; each bit that corresponds to “0” is part of the host number.Gateway The IP address of the router at the next hop to which frames are forwarded.Interface The local interface through which the next hop of this route is reached. Metric When a router receives a routing update that contains a new or changed destination network entry, the router adds 1 to the metric value indicated in the update and enters the network in the routing table.

FIREWALL4-49FirewallThe Barricade Router’s firewall inspects packets at the application layer, maintains TCP and UDP session information including time-outs and the number of active sessions, and provides the ability to detect and prevent certain types of network attacks. Network attacks that deny access to a network device are called Denial-of-Service (DoS) attacks. DoS attacks are aimed at devices and networks with a connection to the Internet. Their goal is not to steal information, but to disable a device or network so users no longer have access to network resources. The Barricade protects against the following DoS attacks: IP Spoofing, Land Attack, Ping of Death, IP with zero length, Smurf Attack, UDP port loopback, Snork Attack, TCP null scan, and TCP SYN flooding. (For details see“Intrusion Detection,” page 4-56.)The firewall does not significantly affect system performance, so we advise enabling the function to protect your network. Select Enable and click the SAVE SETTINGS button.

CONFIGURING THE BARRICADE4-50Access ControlAccess Control allows users to define the outgoing traffic permitted or not-permitted through the WAN interface. The default is to permit all outgoing traffic.The following items are on the Access Control screen: Parameter DescriptionEnable Filtering FunctionEnable or Disable Access control function. Normal Filtering Table Displays descriptive list of Filtering rules defined.

FIREWALL4-51To create a new access control rule:1. Click Add PC on the Access Control screen. The Access Control Add PC screen will appear. 2. Define the appropriate settings for client PC services.3. Click OK and then click SAVE SETTINGS to save your settings.

CONFIGURING THE BARRICADE4-52MAC FilterThe MAC Filter allows you to define what client PC’s can access the Internet. When enabled only the MAC addresses defined in the MAC Filtering table will have access to the Internet. All other client devices will be denied access.You can enter up to 32 MAC addresses in this table. 1. MAC Address Control: select enable or disable.2. MAC Filtering Table: enter the MAC address in the space provided.

FIREWALL4-53URL BlockingThe Barricade allows the user to block access to web sites by entering either a full URL address or just a keyword. This feature can be used to protect children from accessing violent or pornographic web sites. You can define up to 30 sites here.

CONFIGURING THE BARRICADE4-54Schedule RuleYou may filter Internet access for local clients based on rules. Each access control rule may be activated at a scheduled time. Define the schedule on the Schedule Rule screen, and apply the rule on the Access Control screen.

FIREWALL4-55Follow these steps to add a schedule rule: 1. Click Add Schedule Rule on the Schedule Rule screen. The Edit Schedule Rule screen will appear.2. Define the appropriate settings for a schedule rule.3. Click OK and then click SAVE SETTINGS to save your settings.

CONFIGURING THE BARRICADE4-56Intrusion Detection• Intrusion Detection FeatureStateful Packet Inspection (SPI) and Anti-DoS firewall protection (Default: Enabled) — The Intrusion Detection Feature of the Barricade Router limits access for incoming traffic at the WAN port. When the SPI feature is turned on, all incoming packets will be blocked except for those types marked in the Stateful Packet Inspection section. RIP Defect (Default: Enabled) — If an RIP request packet is not acknowledged to by the router, it will stay in the input queue and not be released. Accumulated packets could cause the input queue to fill, causing severe problems for all protocols. Enabling this feature prevents the packets from accumulating.Discard Ping to WAN (Default: Disabled) — Prevent a ping on the Barricade’s WAN port from being routed to the network. Scroll down to view more information.

FIREWALL4-57•Stateful Packet Inspection This is called a “stateful” packet inspection because it examines the contents of the packet to determine the state of the communications; i.e., it ensures that the stated destination computer has previously requested the current communication. This is a way of ensuring that all communications are initiated by the recipient computer and are taking place only with

CONFIGURING THE BARRICADE4-58sources that are known and trusted from previous interactions. In addition to being more rigorous in their inspection of packets, stateful inspection firewalls also close off ports until connection to the specific port is requested. When particular types of traffic are checked, only the particular type of traffic initiated from the internal LAN will be allowed. For example, if the user only checks “FTP Service” in the Stateful Packet Inspection section, all incoming traffic will be blocked except for FTP connections initiated from the local LAN.Stateful Packet Inspection allows you to select different application types that are using dynamic port numbers. If you wish to use the Stateful Packet Inspection (SPI) to block packets, click on the Yes radio button in the “Enable SPI and Anti-DoS firewall protection” field and then check the inspection type that you need, such as Packet Fragmentation, TCP Connection, UDP Session, FTP Service, H.323 Service, or TFTP Service.•When hackers attempt to enter your network, we can alert you by e-mailEnter your email address. Specify your SMTP and POP3 servers, user name, and password.

FIREWALL4-59•Connection PolicyEnter the appropriate values for TCP/UDP sessions as described in the following table. Parameter Defaults DescriptionFragmentation half-open wait10 sec Configures the number of seconds that a packet state structure remains active. When the timeout value expires, the router drops the unassembled packet, freeing that structure for use by another packet. TCP SYN wait 30 sec Defines how long the software will wait for a TCP session to synchronize before dropping the session. TCP FIN wait 5 sec Specifies how long a TCP session will be maintained after the firewall detects a FIN packet. TCP connection idle timeout3600 seconds (1 hour)The length of time for which a TCP session will be managed if there is no activity. UDP session idle timeout30 sec The length of time for which a UDP session will be managed if there is no activity.H.323 data channel idle timeout180 sec The length of time for which an H.323 session will be managed if there is no activity.

CONFIGURING THE BARRICADE4-60•DoS Criteria and Port Scan CriteriaSet up DoS and port scan criteria in the spaces provided (as shown below). Note: The firewall does not significantly affect system performance, so we advise enabling the prevention features to protect your network.Parameter Defaults DescriptionTotal incomplete TCP/UDP sessions HIGH300 sessionsDefines the rate of new unestablished sessions that will cause the software to start deleting half-open sessions.Total incomplete TCP/UDP sessions LOW250 sessions Defines the rate of new unestablished sessions that will cause the software to stop deleting half-open sessions.Incomplete TCP/UDP sessions (per min) HIGH250 sessions Maximum number of allowed incomplete TCP/UDP sessions per minute.Incomplete TCP/UDP sessions (per min) LOW200 sessions Minimum number of allowed incomplete TCP/UDP sessions per minute. Maximum incomplete TCP/UDP sessions number from same host10 Maximum number of incomplete TCP/UDP sessions from the same host. Incomplete TCP/UDP sessions detect sensitive time period300 msec Length of time before an incomplete TCP/UDP session is detected as incomplete.Maximum half-open fragmentation packet number from same host30 Maximum number of half-open fragmentation packets from the same host.Half-open fragmentation detect sensitive time period10000 msec Length of time before a half-open fragmentation session is detected as half-open.Flooding cracker block time300 second Length of time from detecting a flood attack to blocking the attack.

FIREWALL4-61DMZIf you have a client PC that cannot run an Internet application properly from behind the firewall, you can open the client up to unrestricted two-way Internet access. Enter the IP address of a DMZ (Demilitarized Zone) host on this screen. Adding a client to the DMZ may expose your local network to a variety of security risks, so only use this option as a last resort.

CONFIGURING THE BARRICADE4-62UPnPThe Universal Plug and Play architecture offers pervasive peer-to-peer network connectivity of PCs of all form factors, intelligent appliances, and wireless devices. UPnP enables seamless proximity network in addition to control and data transfer among networked devices in the office, home and everywhere within your network.UPnP allows the device to automatically:• join a network• obtain an IP address• convey its capabilities and learn about the presence and capabilities of other devices.Check the Enable radio button to activate this function.

DDNS4-63DDNSDynamic Domain Name Service (DDNS) provides users on the Internet with a method to tie their domain name to a computer or server. DDNS allows your domain name to follow your IP address automatically by having your DNS records changed when your IP address changes.This DNS feature is powered by DynDNS.org or TZO.com. With a DDNS connection you can host your own web site, email server, FTP site, and more at your own location even if you have a dynamic IP address.

CONFIGURING THE BARRICADE4-64ToolsUse the Tools menu to backup the current configuration, restore a previously saved configuration, update firmware, and reset the Barricade.Configuration ToolsChoose a function and click Next. • Backup Router Configuration: this allows you to save the Barricade’s configuration to a file.• Restore from saved Configuration file: this function is used to restore the previously saved backup configuration file.• Restore router to Factory Defaults: this resets the Barricade back to the original default settings.

TOOLS4-65Firmware UpgradeUse this screen to update the firmware or user interface to the latest versions.1. Download the upgrade file from the SMC web site first, and save it to your hard drive.2. Then click Browse... to look for the downloaded file. Click SAVE SETTINGS.Check the Status screen Information section to confirm that the upgrade process was successful.

CONFIGURING THE BARRICADE4-66ResetClick REBOOT ROUTER to reset the ADSL Router. The reset will be complete when the power LED stops blinking. If you perform a reset from this screen, the configurations will not be changed back to the factory default settings.Note: If you use the Reset button on the back panel, the Barricade performs a power reset. If the button is pressed for over 10 seconds, all the LEDs will illuminate and the factory default settings will be restored.

TOOLS4-67STATUSThe Status screen displays WAN/LAN connection status, firmware, and hardware version numbers, illegal attempts to access your network, as well as information on DHCP clients connected to your network. The security log may be saved to a file by clicking Save and choosing a location. Scroll down to view more information on the Status screen.

CONFIGURING THE BARRICADE4-68The following items are included on the Status screen: Parameter DescriptionINTERNET Displays WAN connection type and status.Renew Click on this button to establish a connection to the WAN.GATEWAY Displays system IP settings, as well as DHCP Server and Firewall status.INFORMATION Displays the number of attached clients, the firmware versions, the physical MAC address for each media interface and for the ADSL Router, as well as the hardware version and serial number.Security Log Displays attempts to access your network.Save Click on this button to save the security log file.Clear Click on this button to delete the access log.Refresh Click on this button to refresh the screen.DHCP Client Log Displays information on DHCP clients on your network.

FINDING THE MAC ADDRESS OF A NETWORK CARD4-69Finding the MAC address of a Network CardWINDOWS NT4/2000/XPClick Start/Programs/Command Prompt. Type ipconfig /all and press ENTER.The MAC address is listed as the Physical Address.MACINTOSHClick System Preferences/Network.The MAC address is listed as the Ethernet Address on the TCP/IP tab.LINUXRun the command /sbin/ifconfig. The MAC address is the value after the word HWaddr.

CONFIGURING THE BARRICADE4-70

A-1APPENDIX ATROUBLESHOOTINGThis section describes common problems you may encounter and possible solutions to them. The Barricade can be easily monitored through panel indicators to identify problems. Troubleshooting ChartSymptom ActionLED IndicatorsPower LED is off• Check connections between the Barricade, the external power supply, and the wall outlet.• If the power indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, power cord, or external power supply. However, if the unit powers off after running for a while, check for loose power connections, power losses, or surges at the power outlet. If you still cannot isolate the problem, then the external power supply may be defective. In this case, contact Technical Support for assistance.

TROUBLESHOOTINGA-2LED IndicatorsLAN LED is Off• Verify that the Barricade and attached device are powered on. • Be sure the cable is plugged into both the Barricade and the corresponding device. • Verify that the proper cable type is used and that its length does not exceed the specified limits. • Be sure that the network interface on the attached device is configured for the proper communication speed and duplex mode.• Check the adapter on the attached device and cable connections for possible defects. Replace any defective adapter or cable if necessary. Network Connection ProblemsCannot ping the Barricade from the attached LAN, or the Barricade cannot ping any device on the attached LAN• Verify that the IP addresses are properly configured. For most applications, you should use the Barricade’s DHCP function to dynamically assign IP addresses to hosts on the attached LAN. However, if you manually configure IP addresses on the LAN, verify that the same network address (network component of the IP address) and subnet mask are used for both the Barricade and any attached LAN devices.• Be sure the device you want to ping (or from which you are pinging) has been configured for TCP/IP.Troubleshooting ChartSymptom Action

TROUBLESHOOTINGA-3Management ProblemsCannot connect using the web browser• Be sure to have configured the Barricade with a valid IP address, subnet mask, and default gateway.• Check that you have a valid network connection to the Barricade and that the port you are using has not been disabled.• Check the network cabling between the management station and the Barricade.Forgot or lost the password•Press the Reset button on the rear panel (holding it down for at least six seconds) to restore the factory defaults.Troubleshooting ChartSymptom Action

TROUBLESHOOTINGA-4Wireless ProblemsA wireless PC cannot associate with the Barricade.• Make sure the wireless PC has the same SSID settings as the Barricade. See “Channel and SSID” on page 4-26.• You need to have the same security settings on the clients and the Barricade. See “Security” on page 4-29.The wireless network is often interrupted.• Move your wireless PC closer to the Barricade to find a better signal. If the signal is still weak, change the angle of the antenna.• There may be interference, possibly caused by microwave ovens or wireless phones. Change the location of the possible sources of interference or change the location of the Barricade.• Change the wireless channel on the Barricade. See “Channel and SSID” on page 4-26.• Check that the antenna, connectors, and cabling are firmly connected.The Barricade cannot be detected by a wireless client.• The distance between the Barricade and wireless PC is too great.• Make sure the wireless PC has the same SSID and security settings as the Barricade. See “Channel and SSID” on page 4-26 and “Security” on page 4-29.Troubleshooting ChartSymptom Action

B-1APPENDIX BCABLESEthernet CableCaution:Do not plug a phone jack connector into an RJ-45 port. For Ethernet connections, use only twisted-pair cables with RJ-45 connectors that conform to FCC standards.SpecificationsWiring ConventionsFor Ethernet connections, a twisted-pair cable must have two pairs of wires. Each wire pair is identified by two different colors. For example, one wire might be red and the other, red with white stripes. Also, an RJ-45 connector must be attached to both ends of the cable.Cable Types and SpecificationsCable Type Max. Length Connector10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45100BASE-TX Cat. 5 100-ohm UTP 100 m (328 ft) RJ-45

CABLESB-2Each wire pair must be attached to the RJ-45 connectors in a specific orientation. The following figure illustrates how the pins on an Ethernet RJ-45 connector are numbered. Be sure to hold the connectors in the same orientation when attaching the wires to the pins. Figure B-1. RJ-45 Ethernet Connector Pin NumbersRJ-45 Port Ethernet ConnectionUse the straight-through CAT -5 Ethernet cable provided in the package to connect the Barricade to your PC. When connecting to other network devices such as an Ethernet switch, use the cable type shown in the following table.Attached Device Port Type Connecting Cable TypeMDI-X Straight-throughMDI Crossover

RJ-45 PORT ETHERNET CONNECTIONB-3Pin AssignmentsWith 10BASE-T/100BASE-TX cable, pins 1 and 2 are used for transmitting data, and pins 3 and 6 for receiving data.Straight-Through WiringIf the port on the attached device has internal crossover wiring (MDI-X), then use straight-through cable.RJ-45 Pin AssignmentsPin Number Assignment*1Tx+2Tx-3Rx+6Rx-* The “+” and “-” signs represent the polarity of the wires that make up each wire pair.Straight-Through Cable Pin AssignmentsEnd 1 End 21 (Tx+) 1 (Tx+)2 (Tx-) 2 (Tx-)3 (Rx+) 3 (Rx+)6 (Rx-) 6 (Rx-)

CABLESB-4Crossover WiringIf the port on the attached device has straight-through wiring (MDI), use crossover cable. Crossover Cable Pin AssignmentsEnd 1 End 21 (Tx+) 3 (Rx+)2 (Tx-) 6 (Rx-)3 (Rx+) 1 (Tx+)6 (Rx-) 2 (Tx-)

C-1APPENDIX CSPECIFICATIONSIEEE StandardsIEEE 802.3 10 BASE-T Ethernet IEEE 802.3u 100 BASE-TX Fast EthernetIEEE 802.3, 802.3u, 802.11g, 802.1DLAN Interface4 RJ-45 10 BASE-T/100 BASE-TX portsAuto-negotiates the connection speed to 10 Mbps Ethernet or 100 Mbps Fast Ethernet, and the transmission mode to half-duplex or full-duplexWAN Interface1 RJ-45 portIndicator PanelPower, WAN, Online, WLAN, LAN 1~4, WPSDimensions188 x 133 x 33 mm (7.40 x 5.24 x 1.30 in)Weight0.285 kg (0.764 lbs)Input Power9 V 1 APower Consumption8 Watts maximum

SPECIFICATIONSC-2Advanced FeaturesDynamic IP Address Configuration – DHCP, DNSFirewall – Client privileges, hacker prevention and logging, Stateful Packet InspectionVirtual Private Network – PPTP, L2TP, IPSec pass-through, VPN pass-throughInternet StandardsRFC 826 ARP, RFC 791 IP, RFC 792 ICMP, RFC 768 UDP, RFC 793 TCP, RFC 783 TFTP, RFC 1661 PPP, RFC 1866 HTML, RFC 2068 HTTPRadio FeaturesWireless RF module Frequency Band802.11n Radio: 2.4GHz802.11g Radio: 2.4GHz802.11b Radio: 2.4GHzUSA - FCC2412~2462MHz (Ch1~Ch11)Canada - IC2412~2462MHz (Ch1~Ch11)Europe - ETSI2412~2472MHz (Ch1~Ch13)Japan - STD-T66/STD-332412~2484MHz (Ch1~Ch14)Modulation TypeOFDM, CCKOperating Channels IEEE 802.11n Compliant:11 channels (US, Canada, Europe, Japan)Operating Channels IEEE 802.11g Compliant:11 channels (US, Canada)13 channels (Europe, Japan)

SPECIFICATIONSC-3Operating Channels IEEE 802.11b Compliant:11 channels (US, Canada)13 channels (Europe)14 channels (Japan)Standards ComplianceSafetyLVDEnvironmentalCE MarkTemperatureOperating 0 to 40 °C (32 to 104 °F)Storage -40 to 70 °C (-40 to 158 °F)Humidity5% to 95% (non-condensing)VibrationIEC 68-2-36, IEC 68-2-6ShockIEC 68-2-29DropIEC 68-2-32

SPECIFICATIONSC-4

SMCWBR11-GSMCWBR14S-N2

Navigation menu