Archtek Telecom MIEV56 External 56K Data/Fax Modem User Manual 56TPC

Download:
Mirror Download [FCC.gov]
Document ID	181571
Application ID	Ewk7gCOLKcrcCHK3FAn5mQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	6.84kB (85495 bits)
Date Submitted	2001-11-29 00:00:00
Date Available	2001-11-29 00:00:00
Creation Date	2001-08-17 03:02:04
Producing Software	Acrobat PDFWriter 4.05Windows NT ª©
Document Lastmod	2001-11-09 20:36:32
Document Title	56TPC.PDF
Document Creator	56TPC - Microsoft Word
Document Author:	Lu

IC+ 56K External Modem
User’s Manual
Table Contents
Table Contents .....................................................................................................2
Chapter 1 Installation.......................................................................................3
1. 1 Checking your components.............................................................3
1. 2 Installing the Modem ........................................................................3
1. 3 Windows 95/98/ME/2000 Driver Installation ..............................5
1. 4 Windows NT4.0 Driver Installation ...............................................6
Chapter 2 AT commands set..........................................................................7
2. 1 Data Mode Command ......................................................................8
2. 2 Result Code.................................................................................... 19
2. 3 S Registers Definitions ................................................................. 21
2. 4 Class 1 Fax Commands ............................................................... 28
2. 5 Voice Commands........................................................................... 31
2. 6 AT% TTn Commands .................................................................... 33
Chapter 1 Installation
Chapter 1 provides detailed instructions for installing your modem.
1.1 Checking your components
Unpack your components and make sure you have the following items:
The modem.
A modular telephone cable to connect your modem to the telephone line.
This user's manual.
Communication software and manual.
When you open your package, make sure all of the above items are included and not
damaged. If you see that any components are damaged, please notify your dealer
immediately.
1.2 Installing the modem
The following instructions explain how to install the modem in a IBM compatible type
personal computer. If you will be installing the modem into a different computer, refer
to the manual that accompanied your computer or contact your computer dealer for
instructions on installing the modem in your personal computer.
Step 1
Connecting to a computer.
Plug the male DB-9 connector on your RS-232 cable into the RS-232 connector on the back
the modem.
Step 2
Connecting to the telephone line
Step 3
Connecting to your telephone
Step 4
Connecting to an AC outlet
Step 5
Verifying your connection
If you connected the modem to a computer, place the computer into terminal mode
and complete the configuration information required by the software.
Refer to your computer manual to find out the appropriate command to use.
Then use the following procedure to verify that your connections:
1.
Type AT and press the Enter key. If your system is operating properly, your
modem sends an OK response to your screen and wait for your next command.
If you did not receive a response, make sure your computer is sending commands
to your modem. If this does not solve your problem, contact your computer dealer.
2.
Use your communication software to prepare your computer to dial a call. Then
type AT D x phone number, where x is either T for touch-tone dialing or P for
pulse dialing and phone number is the telephone number that your modem is
using.
For example, if your modem is connected to the telephone line 555-2121 and
Touch-Tone dialing is supported in your calling area, type ATDT 5552121.
3.
Press the Enter key. You should receive a BUSY response and you should hear
the busy signal through the modem speaker because the modem is calling itself.
Your modem is now ready for operation. Refer to the manual that came with your
communication software to begin communications. If you will be communicating
directly with your modem, or if you want to find out more about the modem's operation,
proceed to Chapter 2.
1.3 Windows 95/98/ME/2000 (PNP)
Window 95/98
1.
Boot the system.
2.
Now Windows will begin the “Add New Hardware Wizard” and Search for new drivers for
“IC+ 56k External Modem”. Click “Next”.
3.
Select “Search for the best driver for your device. Click “Next”.
4.
Than insert the driver installation CD into the CD-Rom. Click “Next”.
5.
Windows driver file search for the device “IC+ 56k External Modem Pnp”. Click “Next”.
6.
Click “Finish”.
7.
After completed to copy the modem driver, the “New Hardware Found” will continue to
complete the installation the “Voice Modem Serial Wave Device” for modem.
Window ME
1.
Boot the system.
2.
Now Windows will begin the “Add New Hardware Wizard” and Search for new drivers for
“IC+ 56k External Modem”. Click “Next”.
3.
Select “Search for the best driver for your device. Click “Next”.
4.
Than insert the driver installation CD into the CD-Rom. Click “Next”.
5.
Windows driver file search for the device “IC+ 56k External Modem Pnp”. Click “Next”.
6.
Click “Finish”.
7.
After completed to copy the modem driver, the “New Hardware Found” will continue to
complete the installation the “Voice Modem Serial Wave Device” for modem.
Window 2000
1.
Boot the system.
2.
Now Windows will begin the “Found New Hardware Wizard”. Click “Next”.
3.
Select “Search for a suitable driver for my device (recommended). Click “Next” button.
4.
Please select “Specify a location” item and put driver disk into the CD-ROM. Click “Next”.
5.
The wizard found a driver for the following device “IC+ 56k External Modem”. Click
“Next”.
6.
Windows finds your modem model “IC+ 56k External Modem Pnp”. Click on the “Finish”
button if the displayed modem model name fits yours.
1.4 Windows NT4.0
1.
Boot the system.
2.
Double-Click Control Panel => Modems.
3.
Click “Next”.
4.
Click “Change… ” then select “Have Disk… ” button.
5.
Select modem model “IC+ 56k External Modem” Click “Next”.
6.
Click “Finish”.
7.
Click “Close”.
8.
Setup “RAS” to continue.
9.
Restart the system.
10. Now you’ve completed to install the drivers for the modem.
NOTE: Microsoft does not support plug and play in Windows NT 4.0.
Chaper 2
AT Commands Set
AT commands are issued to DTE to control the modem's operation. AT commands
can only be entered while the modem is in command mode. Except for the A/
command and the +++ escape command, all commands must be prefixed with the
attention code AT. For instance, the “A” command (below) would be entered as:
"ATA". With out the AT prefix, the command line cannot be executed. For
example: The format for entering AT commands is “ATXn” where X is the AT
command, and n is the specific value for that command.
More than one command can be placed on a single line and (if desired) separated
with spaces for readability. Once the carriage return (Enter) key is pressed, the
command line is executed. A line with no carriage return is ignored. Any command
issued is acknowledged with a response in either text or numeric values known as
result codes. In the following, all commands, command-values and result code
recognized by the modem are shown; any entries other than those shown cause the
ERROR result code. The modem accepts either upper or lower case characters in the
command line and ignores any spaces within or between commands. Typing errors
can be corrected with the Backspace key. Exceptions are noted in the description of
specific commands.
+++AT Escape Sequence
The escape sequence allows the modem to exit data mode and enter online
command mode. While in online command mode, you may communicate directly to
your modem using AT commands. You may return to data mode by issuing the ATO
command.
2.1 Data Mode Command
A/ Executes Last Command
When modem receives this command, modem executes the last command string
entered. Do not conclude it by pressing “Enter”.
A Answer Command
This command instructs the modem to go off-hook and answer an incoming call.
Bn Communication Standard Setting
This command determines ITU-T vs. Bell standard.
B0 Selects ITU-T V.22 mode when the modem is at 1200 bits/s.
B1 Selects Bell 212A when the modem is at 1200 bits/s (default).
Result Codes:
OK : n = 0, 1, 15, 16
ERROR : Otherwise
Dn Dial
This command instructs the modem to begin the dialing sequence. A dial string can
be up to 40 characters long. Any digit or symbol (0-9, *, #, A, B, C, D) could be dialed
as touch-tone digits. The following may be used as dial string modifiers:
P Pulse dialing.
T Touch tone dialing (default).
W Wait for second dial tone.
@ Wait for quiet answer. Wait for five seconds of silence after dialing the number.
! Hook flash.
, Pause during dialing.
; Return to command mode.
^ Disable data calling tone transmission.
S = n Dial a telephone number previously stored using the &Zn = x command
(see the &Zn = x command for further information). The range of n is 0?.
En Echo Command
ATEn command controls whether or not the characters entered from your computer
keyboard are echoed back to your monitor while the modem is in command mode.
E0 Disables echo to the computer.
E1* Enables echo to the computer (default).
Result Codes:
OK: n = 0, 1
ERROR: Otherwise
Hn Hook Control
This command instructs the modem to go on-hook to disconnect a call, or off-hook to
make the phone line busy.
H0 Modem goes on-hook (default).
H1 Modem goes off-hook.
Result Codes:
OK: n = 0, 1
ERROR: Otherwise
In Request Identification Information
This command displays specific product information about the modem.
I0 Returns product ID code.
I1 Display Firmware version and checksum on the DTE.
I2 Customer Used.
I3 Returns fix ID information for application software identification.
“TP560 Data/Fax/Voice 56K Modem”
I4 Returns firmware version for data pump.
I5 Returns country code.
I6 Return Local Phone Status (Loop Current Detection)
0: On-hook, 1: Off-hook
Result Codes:
n = 0, 1, 2, 3, 4, 5,6
ERROR: Otherwise
Ln Monitor Speaker Volume
This command sets speaker volume to low, medium, or high.
L0 Select low volume.
L1 Select low volume.
L2* Select medium volume.
L3 Select high volume.
Result Codes:
OK n = 0, 1, 2, 3
ERROR Otherwise
Mn Monitor Speaker Mode
This command turns the speaker on or off.
M0 The speaker is off.
M1* The speaker is on until the modem detects the carrier signal.
M2 The speaker is always on when modem is off-hook.
M3 The speaker is on until the carrier is detected, except while dialing.
Result Codes:
OK n = 0, 1, 2, 3
ERROR Otherwise
Nn Modulation Selection
This command controls whether or not the local modem performs a negotiated
handshake at connection time with the remote modem when the communication
speed of the two modems is different.
N0 When originating or answering, this is for handshake only at the
communication standard specified by AT*Nn.
N1* During handshake, Highest speed is specified by AT*Nn.
Depend on line quality fallback to a lower speed may occur.
Result Codes:
OK n = 0, 1
ERROR Otherwise
On Return Online to Data Mode
O0* Exit online command mode and return to data mode (see AT Escape
Sequence, +++AT).
O1 This command issues a retrain before returning to online data mode.
O2 This command issues a rate re-negotiation before returning to online data
mode.
Result Codes:
OK n = 0, 1, 3
ERROR Otherwise
P Select Pulse Dialing
This command configures the modem for pulse (non-touch-tone) dialing.
10
Qn Result Code Control
Result codes are informational messages sent from the modem and displayed
on your monitor.
Q0* Enables modem to send result codes to the DTE.
Q1 Disables modem from sending result codes.
Result Codes:
OK n = 0, 1
ERROR Otherwise
T Select Tone Dialing
This command instructs the modem to send DTMF tones while dialing.
Vn DCE Response Format
This command controls whether result codes are displayed as words or their
numeric equivalents.
V0 Displays result codes as numeric.
V1* Displays result codes as text.
Result Codes:
OK n = 0, 1
ERROR Otherwise
Wn Result Code Option
W0 Display ”CONNECT DCE speed?without V42/MNP extended.
W1 Display ”CONNECT DTE speed?without V42/MNP extended.
W2* Display ”CONNECT DCE speed?with V42/MNP extended.
W3 Display ”CONNECT DTE speed?with V42/MNP extended.
Result Codes:
OK n = 0, 1, 2
ERROR Otherwise
Xn Result Code Selection and Call Progress detection
This command enables tone detection options during dialing procedure. As these
functions are chosen, the modem chip set result codes are also affected. Therefore,
this command is frequently used to control the modem chip set responses and dial
tone detection.
Result Codes:
OK n = 0, 1, 2, 3, 4, 5, 6, 7
ERROR Otherwise
Zn Recall Stored Profile
This command instructs the modem chip set to go on-hook and restore the profile
11
saved by the last &W command.
Z0 Reset modem and retrieve active configuration profit from stored profit 0.
Z1 Reset modem and retrieve active configuration profit from stored profit 1.
Result Codes:
OK n = 0, 1
ERROR Otherwise
&Cn Data Carrier Detect (DCD) Control
Data carrier detect is a signal from the modem to your computer indicating that the
carrier signal is being received from a remote modem. DCD normally turns off when
the modem no longer detects the carrier signal.
&C0
The state of the carrier from the remote modem is ignored. DCD circuit
is always on.
&C1* DCD turns on when the remote modem's carrier signal is detected, and
off when the carrier signal is not detected.
Result Codes:
OK n = 0, 1
ERROR Otherwise
&Dn DTR Control (Data Terminal Ready)
This command interprets how the modem responds to the state of the DTR signal and
changes to the DTR signal.
&D0 Ignore.
&D1 If the DTR signal is not detected while in online data mode, the modem
enters command mode, issues OK result code, and remains connected.
&D2* If the DTR signal is not detected while in online data mode, the modem
disconnects.
&D3 Monitor DTR signal when an on-to-off transition occurs, the modem
performs a soft reset as if the ATZ command was received.
Result Codes:
OK n = 0, 1, 2, 3
ERROR Otherwise
&Fn Load Factory Settings
This command loads the configuration stored and programmed at the factory. This
operation replaces all of the command options and the S-register settings in the active
configuration with factory values.
&Gn V.22bis Guard Tone Control
12
This command determines guard tone frequency and is only used in V.22 and V.22bis
mode. This option is not used in North America and is for international use only.
&G0* Guard tone disabled.
&G1 Sets guard tone to 550 Hz.
&G2 Sets guard tone to 1800 Hz.
Result Codes:
OK n = 0, 1, 2
ERROR Otherwise
&Kn Local Flow Control Selection
&K0 Disable flow control.
&K1 Reserved.
&K2 Reserved.
&K3 Enable RTS/CTS flow control.
&K4 Enable XON/XOFF flow control.
&K5 Enable Transparent XON/XOFF flow control.
Result Codes:
OK n = 0,1,2, 3, 4
ERROR Otherwise
&Pn Pulse Dial Make-to-Break Ratio Selection
&P0* 39/61 make-to-break ratio (10 pps).
&P1 33/67 make-to-break ratio 10 pps).
&P2 39/61 make-to-break ratio (20 pps)
&P3 33/67 make-to-break ratio (20 pps)
Result Codes:
OK n = 0, 1
ERROR Otherwise
&Rn Clear To Send Signal Select
&R0 Modem turns on the Clear To Send signal when it detects the Request
To Send (RTS) signal.
&R1* Modem turns on Clear To Send signal.
Result Codes:
OK n = 0, 1
ERROR Otherwise
13
&Sn Data Set Ready (DSR) Option
This command selects DSR action.
&S0* DSR always ON.
&S1 DSR comes on when establishing a connection and goes off when the
connection ends.
Result Codes:
OK n = 0, 1
ERROR Otherwise
&Un Protocol Selection
&U0 Select V.PCM
&U1 Select V.34Bis/V.34
&U2 Select V.32Bis/V.22Bis
&U3 Select Bell 103 300bps
&U4 Select V21 300bps
&U5 Select V23
&V View Active Configuration and Stored Profile
This command is used to display the active profiles.
&Wn Store Current Configuration
This command stores certain command options and S-register values into the modem
nonvolatile memory. The ATZ command or a power up reset of the modem restores
this profile.
&W0* Stores active configuration profile in configuration profit 0.
&W1 Stores active configuration profile in configuration profit 1.
Result Codes:
OK n = 0
ERROR Otherwise
&Yn Select Stored Profile for Power On or Reset
This command does not change the behavior of the modem but is included for
compatibility with applications that issue the &Y0 command
&Y0 Select stored profile 0.
&Y1 Select stored profile 1.
Result Codes:
OK n = 0
ERROR Otherwise
14
&Zn = x Store Telephone Number
This command is used to store up to three dialing strings in the modem
nonvolatile memory for later dialing. The format for the command is &Zn =
stored number where n is the location 0? to which the number should be
written. The dial string may contain up to 31 characters. The ATDS = n
command dials using the string stored in location n.
Result Codes:
OK n = 0, 1, 2
ERROR Otherwise
*In Connect Speed Selection
*I0 Selects connect speed 1200bps
*I1 Selects connect speed 2400bps
*I2 Selects connect speed 4800bps
*I3 Selects connect speed 7200bps
*I4 Selects connect speed 9600bps
*I5 Selects connect speed 12000bps
*I6 Selects connect speed 14400bps
*I7 Selects connect speed 16800bps
*I8 Selects connect speed 19200bps
*I9 Selects connect speed 21600bps
*I10 Selects connect speed 24000bps
*I11 Selects connect speed 26400bps
*I12 Selects connect speed 28800bps
*I13 Selects connect speed 31200bps
*I14* Selects connect speed 33600bps
select V.pcm
*I1 Selects connect speed 28000bps
*I2 Selects connect speed 29333bps
*I3 Selects connect speed 30666bps
*I4 Selects connect speed 32000bps
*I5 Selects connect speed 33333bps
*I6 Selects connect speed 34666bps
*I7 Selects connect speed 36000bps
*I8 Selects connect speed 37333bps
*I9 Selects connect speed 38666bps
*I10 Selects connect speed 40000bps
15
*I11
*I12
*I13
*I14*
*I15
*I16
*I17
*I18
*I19
*I20
*I21
*I22
Selects connect speed 41333bps
Selects connect speed 42666bps
Selects connect speed 44000bps
Selects connect speed 45333bps
Selects connect speed 46666bps
Selects connect speed 48000bps
Selects connect speed 49333bps
Selects connect speed 50666bps
Selects connect speed 52000ps
Selects connect speed 53333bps
Selects connect speed 54666bps
Selects connect speed 56000bps
*Gn User Abort Selection
*G0* Enables user abort feature
*G1 Disables user abort feature
*Hn Auto Retrain Selection
*H0 Disables auto retrain
*H1* Enables auto retrain
*NCnn Country select
This command provides customers chose the country for phone line regulation.
*NC40
*NC1
*NC2
*NC3
*NC4
*NC5
*NC6
*NC17
*NC10
*NC7
*NC8
*NC43
*NC26
*NC11
*NC12
*NC27
Australia
Austria
Belgium
Denmark
Finland
France
Germany
Greece
Netherlands
Ireland
Italy
Japan
Namibia
Norway
Portugal
South Africa
16
*NC13 Spain
*NC14 Sweden
*NC15 Switzerland
*NC16 UK
*NC19 Czech Republic
*NC24 Poland
*NC25 Russia
*NC22 United States
*Tn Trellis Coding Selection
*T0 Disables Trellis coding
*T1* Enables Trellis coding
*On Transmission Level Selection
*O0* Selects output level -11dBm
*O1 Selects output level -12dBm
*O2 Selects output level -13dBm
*O3 Selects output level -14dBm
*O4 Selects output level -15dBm
*O5 Selects output level -16dBm
*O6 Selects output level -17dBm
*O7 Selects output level -18dBm
*O8 Selects output level -19dBm
*O9 Selects output level -20dBm
*O10 Selects output level -21dBm
*O11 Selects output level -22dBm
*O12 Selects output level -23dBm
*O13 Selects output level -24dBm
*O14 Selects output level -25dBm
*O15 Selects output level -26dBm
\ Nn Error Control Mode Selection
This command determines the type of error control used by the modem when sending
or receiving data.
\ N0 Normal mode.
\ N1 Direct mode.
\ N2 MNP or disconnect mode. The modem attempts to connect using MN
2-4 error control procedures. If this fails, the modem disconnects.
This is also known as MNP reliable mode.
\ N3 MNP, or buffer.
17
The modem attempts to connect using MNP 2-4 error control procedures. If
this fails, the modem will connect in Normal modem
\ N4 V.42 with ODP & ADP phase detection.
\ N5* V.42 with ODP & ADP phase detection, MNP, or buffer (default).
The modem attempts to connect in V.42 error control mode. If this fails, the
modem attempts to connect in MNP mode. If this fails, the modem connects in
buffer mode and continues operation. This is also known as V.42/ MNP auto
reliable mode.
\N6 V.42 or disconnect. The modem attempts to connect in V.42 error control
mode. If this fails, the call will be disconnected.
\ N7 V.42, MNP, or buffer (default).
Result Codes:
OK n = 0, 1, 2, 3, 4, 5, 6
ERROR Otherwise
\ Vn Protocol Result Code
\V0* Disable protocol result code appended to DCE speed.
\ V1 Enable protocol result code appended to DCE speed.
Result Codes:
OK n = 0, 1
ERROR Otherwise
%Cn Data Compression Control
This command determines the operation of V.42bis and MNP class 5 data
compression. Online changes do not take effect until a disconnection occurs first.
%C0 V.42bis/ MNP 5 disabled. No data compression.
%C1 V.42bis/ MNP 5 enabled. Data compression enabled (default).
Result Codes:
OK n = 0, 1
ERROR Otherwise
18
2. 2 Result Code
Long Form
Short Form
OK
CONNECT
RING
NO CARRIER
ERROR
CONNECT 1200
NO DIALTONE
BUSY
NO ANSWER
CONNECT 300
CONNECT 2400
CONNECT 4800
CONNECT 9600
CONNECT 7200
CONNECT 12000
CONNECT 14400
CONNECT 19200
CONNECT 38400
CONNECT 57600
CONNECT 115200
CONNECT 1200TX/75RX
CONNECT 75TX/1200RX
RINGBACK
CONNECT BELL 300
CONNECT V21
10
11
12
13
14
20
21
22
23
24
25
26
27
28
29
n value in ATXn
0 1 2 3 4
x x x x x
x x x x x
x x x x x
x x x x x
x x x x x
x x x x
x x
x x
x x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
x x x x
( Display DCE speeds by ATW0 and ATW2 )
CONNECT
CONNECT
CONNECT
CONNECT
CONNECT
CONNECT
16800
19200
21600
24000
26400
28800
15
16
17
21
30
31
19
CONNECT 31200
CONNECT 33600
32
33
(V.90 mode)
CONNECT 28000
CONNECT 29333
CONNECT 30666
CONNECT 32000
CONNECT 33333
CONNECT 34666
CONNECT 36000
CONNECT 37333
CONNECT 38666
CONNECT 40000
CONNECT 41333
CONNECT 42666
CONNECT 44000
CONNECT 45333
CONNECT 46666
CONNECT 48000
CONNECT 49333
CONNECT 50666
CONNECT 52000
CONNECT 53333
CONNECT 54666
CONNECT 56000
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
20
2.3
S Registers Definitions
S registers generally affect how the AT commands perform. Contents of the registers
can be displayed or modified when the modem is in command mode. To display the
value of an S register: TYPE: ATSn?, where n is the register number.
PRESS: Enter To modify the value of an S register:
TYPE: ATSn = r where n is the register number, and r is the new register value.
PRESS: Enter
S0 Auto Answer Ring Number
This register determines the number of rings the modem will count before
automatically answering a call. 0 (zero) is that asks modem don?t do automatically
answer at all. When disabled, the modem can only answer with an ATA command.
Range: 0-55
Default: 0
Units: rings
S1 Ring Counter
This register, ring counter, is read only. The value of S1 is incremented with each ring.
If no rings occur over a 6 second interval, this register is cleared.
Range: 0-55
Default: 0
Units: rings
S2 AT Escape Character (User Defined)
This register determines the ASCII valued used for an escape sequence. The default
is the ??character. The escape sequence allows the modem to exit data mode and
enter command mode. Values greater than 127 disable the escape sequence.
Range: 0-255
Default: 43
Units: ASCII
S3 Command Line Termination Character (User Defined)
This register determines the ASCII values as the carriage return character. This
character is used to end command lines and result codes.
Range: 0-127, ASCII decimal
Default: 13 (carriage return)
Units: ASCII
21
S4 Response Formatting Character (User Defined)
This register determines the ASCII value used as the line feed character. The modem
uses a line feed character in command mode when it responds to the computer.
Range: 0-127, ASCII decimal
Default: 10 (line feed)
Units: ASCII
S5 Command Line Editing Character (User Defined)
This register sets the character recognized as a backspace and pertains to
asynchronous only.
Range: 0-127, ASCII decimal
Default: 8 (backspace)
Units: ASCII
S6 Wait Before Dialing
This register sets the length of time, in seconds, that the modem must wait (pause)
after going off-hook before dialing the first digit. The modem always pauses for a
minimum of two seconds, even if the value of S6 is less than two seconds. Waiting for
dial tone call progress features (W dial modifier in the dial string) will override the
value in register S6. This operation, however, may be affected by some ATX options
according to country restrictions.
Range: 2-10
Default: 2
Units: seconds
S7 Connection Completion Timeout
This register sets the time, in seconds, that the modem must wait before hanging up
because carrier is not detected. The timer is started when the modem finishes dialing
(originate), or goes off-hook (answer). In originate mode, the timer is reset upon
detection of an answer tone if allowed by country restriction. The timer also specifies
the wait for silence time for the @ dial modifier in seconds. S7 is not associated with
the W dial modifier.
Range: 1-255
Default: 45
Units: seconds
S8 Comma Dial Modifier Time
This register sets the time, in seconds, that the modem must pause when it
22
encounters a comma (,) in the dial command string.
Range: 1-255
Default: 2
Units: seconds
S9 Carrier Detect Response Time
Register S9 sets the time the remote modem's carrier signal must be present for the
local modem to recognize it. This feature ensures that your modem does not mistake
a busy signal, ring, or voice for the carrier signal. The value of this register is in tenths
of a second. The default value is 600 ms , although you can change it from 1 to 255.
For example, entering a value 13 means that the remote modem's carrier signal must
be present for 1.3 seconds for the local modem to recognize it. Setting this value
higher increases the chances the modem will not mistakenly identify the carrier signal.
S10 Automatic Disconnect Delay after Carrier Loss
This register sets the length of time, in tenths of a second, that the modem waits
before hanging up after a loss of carrier. This allows for a temporary carrier loss
without causing the local modem to disconnect. The actual interval the modem waits
before disconnecting is the value in register S10.
Range: 1-254
Default: 14
Units: 0.1 seconds
S11 DTMF Dialing Speed
This register determines the dialing speed which is prefixed for each country.
Range: 50-255
Default: 95
Units: 0.001 seconds
S12 Escape Guard Time
This register sets the value (in 20 ms increments) for the required pause after the
escape sequence (default 1 s).
Range: 0-255
Default: 50
Units: 0.02 seconds
S14 Bit-mapped Register
Bit-mapped register S14 lets you control modem echo, responses, dialing method,
23
and the original or answer mode.
Bit Function
0=0 Do not echo command (E0)
1 Echo command (E1) – default
1 Reserved
2 Mapping to ATQn
3=0 Numeric responses (V0)
1 Verbose (Verbal) Responses (V1) – default
4,5= Mapping to AT&P
6=0 Use touch-tone dialing method (T) – default
1 Use pulse dialing method (P)
7=0 Answer incoming calls (A)
1 Originate calls (D) – default
S21 Bit-mapped Register
Bit-mapped register S21 lets you control certain data communication control signals.
Bit Function
0,1= x Undefined
2= Mapping to AT&R
3,4=0 Modem ignores the DTR signal (&D0)
1 Modem enters command mode after ON-to-OFF DTR transition (&D1)
2 Modem hangs up after ON-to-OFF DTR transition (&D2) – default
3 Modem resets after ON-to-OFF DTR transition (&D3)
5=0 CD signal always on (&C0)
1 CD signal on when a remote carrier signal is present (&C1) – default
6 =0 AT&S=0
1 AT&S=1
S22 Bit mapped Register
Bit-mapped register S22 lets you control internal speaker and the modem responses.
Bit
Function
0,1= 0 Speaker volume off (L0)
1 Low speaker volume (L1)
2 Medium speaker volume (L2) – default
3 Loud speaker volume (L3)
2,3= 0 Speaker off (M0)
1 Speaker on until carrier detected (M1) – default
2 Speaker always on (M2)
24
3 Speaker on until carrier detected but off during dialing (M3)
4,5,6=0 Hayes Smart modem compatibility (X0)
4 Include CONNECT XXX responses (X1)
5 Same as 4 plus dial tone detection (X2)
6 Same as 4 plus BUSY response and blind dialing (X3)
7 Same as 6 plus dial tone detection (X4) – default
7 =0 Undefined
S23 Bit-mapped Register
Bit
Function
0,1,2,3= 0 0-300bps DTE data rate
1 1200bps DTE data rate
2 2400bps DTE data rate
3 4800bps DTE data rate
4 9600bps DTE data rate
5 14400bps DTE data rate
6 19200bps DTE data rate
7 34800bps DTE data rate
8 57600bps DTE data rate
9 115200bps DTE data rate
4,5= 0
Use even parity
Use none parity
Use odd parity
Use mark parity
6,7= 0
Mapping to AT&G
S25 Data Terminal Ready Delay
When Modem is on-line, it will ignore a Data Terminal Ready signal lasting less than
the value of this register. In this mode, the values for this register are 0 to 255 in
hundredths of a second, and the default value is 0.05 seconds. If you will be entering
synchronous mode after dialing asynchronously, this register determines how long the
modem waits before looking for the Data Terminal Ready signal. This lets you detach
the asynchronous terminal and connect a synchronous terminal while remaining in the
Data Mode. The default value is 5
Range: 0-255
Default: 5
Units: 0.01 seconds
25
S26 Request To Send-to-Clear To Send Delay
This register affects synchronous operation only and applies only when you are using
the &R0 command. This register determines how long the modem waits to turn on the
Clear To Send signal after a Request To Send OFF-to-ON transition in 10 ms
increment. The default value is 1.
Range: 0-255
Default: 1
Units: 0.01 seconds
S29
Bit Value Function
0-4 Mapping to AT*I
5-7 Mapping to AT&U
S30 Inactivity Timer
S30 specifies the length of time (in minutes) that the modem will wait before
disconnecting when no data is sent or received. This function is only applicable to
buffer mode.
Range: 0-255
Default: 0
Units: minutes
S45 Timer to Control Sleep Mode
This command displays the number of seconds of inactivity (no characters sent from
the DTE, no RING) in the off-line command state before the modem places itself into
standby mode. A value of zero prevents standby mode.
Note: If a number between 1 and 4 is entered for this register, it will set the value to 5,
and the inactivity before standby will be 5 s. This is done for compatibility with
previous products which allowed time-outs down to 1 s.
Range: 0, 5-255
Default: 10
S95
Bit Value Function
0,1 Mapping to ATWn
2 Mapping to AT\V
3 Mapping to ATN
4 Mapping to AT*O
26
S96 Local Phone Status
This register tells the status of the Local Phone. It is read only.
0 = local phone on-hook
1 = local phone off-hook
S97
Bit Value Function
0-2 Mapping to AT\Nn
7 Mapping to AT%Cn
S98
Bit Value Function
0,1 Mapping to AT*H
2 Mapping to AT*G
3 Mapping to AT*T
4-6 Mapping to AT&K
S99 Energy detection threshold
This register can use in Call Progress Mode (CPM) mode, for dial tone detection
threshold. The default value is 2. This register determines the detection threshold for
Call Progress (CPM) tones. The default value is 2.
27
2.4
Class 1 FAX Commands
The modem chip set supports FAX commands conforming to EIA standard 578.
These commands are given here with short descriptions; complete explanations are
given in the standard, available from the Electronic Industry Association.
FAX Command Set Summary
+FCLASS?
Service class indication
+FCLASS = ? Service class capabilities
+FCLASS = n Service class selection
+FTM = 
Transmit FAX data
+FRM = 
Receive FAX data
+FTH = 
Transmit HDLC data
+FRH = 
Receive HDLC data
+FTM = ?
Check transmit FAX modulation
+FRM = ?
Check receive FAX modulation
+FTH = ?
Check transmit HDLC data modulation
+FRH = ?
Check receive HDLC data modulation
+FMI = ?
Check manufacturer identification
+FMM = ?
Check product identification
+FMR = ?
Check version/revision information
+FLO = ?
Select Flow Control specified
+FPR = ?
Select Serial Port Rate
+FCLASS? Service Class Indication
This command causes the modem to display the current setting. The modem
can operate either as a class 0 data modem or a class 1 FAX modem.
Responses: 000 :data mode
001 if in FAX class 1
008 if in voice mode
+FCLASS = ? Service Class Capabilities
This command causes the modem to display the classes it supports.
Typical responses:
+FCLASS = ? 0, 1, 8
+FCLASS = n Service Class Selection
This command sets the modem for class n operation,where n is either a 0 or 1.
Parameters: 0, 1, 8
Default: 0
Command options:
28
+FCLASS = 0 Select data mode.
+FCLASS = 1 Select facsimile class 1.
+FCLASS = 8 Select voice mode.
+FTS =  Stop transmission and pause
+FTM =  Transmit FAX Data
This command causes the modem to transmit data at the modulation specified by
. The following table shows the values you can enter for this command and the
meaning of those values.
+FTM
+FTM
+FTM
+FTM
+FTM
+FTM
+FTM
+FTM
+FTM
+FTM
+FTM
+FTM
+FTM
=3
= 24
= 48
= 72
= 96
= 73
= 74
= 97
= 98
= 121
= 122
= 145
= 146
V.21 Channel2 300
V.27ter 2400
V.27ter 4800
V.29 7200
V.29 9600
V.17 7200
V.17 (short train) 7200
V.17 9600
V.17 (short train) 9600
V.17 12000
V.17 (short train) 12000
V.17 14400
V.17 (short train) 14400
+FRM =  Receive FAX Data
This command causes the modem to receive data at the modulation specified by
.
+FRM = 3 V.21 Channel2 300
+FRM = 24 V.27ter 2400
+FRM = 48 V.27ter 4800
+FRM = 72 V.29 7200
+FRM = 96 V.29 9600
+FRM = 73 V.17 7200
+FRM = 74 V.17 (short train) 7200
+FRM = 97 V.17 9600
+FRM = 98 V.17 (short train) 9600
+FRM = 121 V.17 12000
+FRM = 122 V.17 (short train) 12000
+FRM = 145 V.17 14400
+FRM = 146 V.17 (short train) 14400
29
+FTH =  Transmit HDLC Data
This command causes the modem to transmit data framed in the HDLC
protocol at the modulation specified by .
+FTH = 3 V.21 Channel2 300
+FTH = 24 V.27ter 2400
+FTH = 48 V.27ter 4800
+FTH = 72 V.29 7200
+FTH = 96 V.29 9600
+FTH = 73 V.17 7200
+FTH = 74 V.17 (short train) 7200
+FTH = 97 V.17 9600
+FTH = 98 V.17 (short train) 9600
+FTH = 121 V.17 12000
+FTH = 122 V.17 (short train) 12000
+FTH = 145 V.17 14400
+FTH = 146 V.17 (short train) 14400
+FRH =  Receive HDLC Data
This command causes the modem to receive data framed in the HDLC
protocol at the modulation specified by .
+FRH = 3 V.21 Channel2 300
+FRH = 24 V.27ter 2400
+FRH = 48 V.27ter 4800
+FRH = 72 V.29 7200
+FRH = 96 V.29 9600
+FRH = 73 V.17 7200
+FRH = 74 V.17 (short train) 7200
+FRH = 97 V.17 9600
+FRH = 98 V.17 (short train) 9600
+FRH = 121 V.17 12000
+FRH = 122 V.17 (short train) 12000
+FRH = 145 V.17 14400
+FRH = 146 V.17 (short train) 14400
+FLO =  Flow Control Select
+FLO=0 Xon/Xoff and RTS/CTS flow control Turned off
+FLO=1 Xon/Xoff flow control
+FLO=2 RTS/CTS flow control
+FPR =  Serial Port Rate
30
2.5
Voice Commands
+VIP
Initial voice parameter
+VCID= Caller ID
pmode=0:Disable Caller ID
pmode=1: Enable ,formatted caller report
pmode=2:Enable ,unformatted caller report
+VCID? Report current parameter
+VCID=? Queries the range that DCE support
+VDR
Enable the distinctive ring feature
+VDR?
Report current parameter
+VDR=? Queries the range that DCE support
+VGT
Setup playback gain
+VGT?
Report current parameter
+VGT=? Queries the range that DCE support
+VGR
Setup record gain
+VGR?
Report current parameter
+VGR=? Queries the range that DCE support
+FMI?
Report manufacturer ID
+FMM?
Report product information
+FMR?
Report product revision
+VIT
Enable inactive timer
+VIT?
Report current parameter
+VIT=?
Queries the range that DCE support
+VTD
Set the default duration for DTMF/tone generation in 10ms
increments
+VTD?
Report current parameter
+VTD=?
Queries the range that DCE support
+VSD=
sds=128 Normal level of sensitivity(-40dbm)
sds>= 128 More aggressive ;ex. sds=129 is –39dbm
sds<= 128 Less aggressive :ex sds=127 is –40dbm
sdi :Specify the amount of time the modem will report silence to DTE
+VSD?
Report current parameter
+VSD=? Queries the range that DCE support
+VTS
DTMF and tone generation
+VTS=?
Queries the range that DCE support
ex1: AT+VTS=1 play DTMF 1 with a duration by the +VTD command
31
ex2: AT+VTS=2 play DTMF 2 with a duration by the +VTD command
ex3: AT+VTS=[1000,1300,50] play tone pair 1000Hz and 1300hz with a
duration of 50ms
ex4: AT+VTS={*,6} play DTMF * with a duration of 60ms
ex5: AT+VTS=9 play DTMF 9 with a duration by the +VTD command
+VTX
Enter voice playback mode
+VRX
Enter voice record mode
+VSM=,
cml=128 , select linear 8bit PCM
cml=132 , select IMA ADPCM
vsr =xx, Sample rate is always 8000
+VSM? Report current parameter
+VSM=? Queries the range that DCE support
+VPR= DTE/DCE rate will be equal 2400*rate , but auto-baud if rate=0
+VPR?
Report current parameter
+VPR=?
Queries the range that DCE support
+VLS=
pmode=0: DCE on-hook, local phone connected to Telco.
pmode=1: DCE off-hook, DCE connected to Telco
pmode=2: DCE off-hook, local phone connected to DCE
pmode=3: DCE off-hook, local phone connected to Telco, DCE to
local phone
pmode=4: Speaker connected to DCE,DCE on-hook(playback
message)
pmode=5: Speaker connected to DEC, DCE off-hook(call screening)
pmode=6: Microphone connected to DCE, DCE on-hook(Record
greeting)
pmode=7: Microphone and speaker connected , DCE off-hook
(speakerphone)
32
2.6
AT% TTn Commands
%tt0=0 erase %TT command
%tt1=n Tx v90 signal
%tt2=A,B,C,D Tx v34 signal parameter
A: Baud Rate
B: Data Rate
C: Min/Exp
D: Pre-emphasis
%tt3=0 : DTMF '0'
%tt3=1 : DTMF '1'
%tt3=2 : DTMF '2'
%tt3=3 : DTMF '3'
%tt3=4 : DTMF '4'
%tt3=5 : DTMF '5'
%tt3=6 : DTMF '6'
%tt3=7 : DTMF '7'
%tt3=8 : DTMF '8'
%tt3=9 : DTMF '9'
%tt3=10 : DTMF 'A'
%tt3=11 : DTMF 'B'
%tt3=12 : DTMF 'C'
%tt3=13 : DTMF 'D'
%tt3=14 : DTMF '*'
%tt3=15 : DTMF '#'
%tt3=16 : V32 9600
%tt3=17 : V32 14400
%tt3=18 : 2100HZ ANSWER TONE
%tt3=19 : 1300HZ CALLING TONE
%tt3=20 : 1100HZ CALLING TONE
%tt3=21 :
%tt3=22 : Silence
%tt4=0
%tt4=1
%tt4=2
%tt4=3
V21
V21
V21
V21
Org tx mark
Org tx space
Ans tx mark
Ans tx space
33
%tt4=4 : V23 Org tx mark
%tt4=5 : V23 Org tx space
%tt4=6 : V23 Ans tx mark
%tt4=7 : V23 Ans tx space
% tt4=8 : V22 org
%tt4=9 : V22bis org
%tt4=10 : V22 ans (tx guard tone if &g1 or &g2)
%tt4=11 : V22bis ans (tx guard tone if &g1 or &g2)
%tt5= 0 : V27ter 2400
%tt5= 1 : V27ter 4800
%tt5= 2 : V29 7200
%tt5= 3 : V29 9600
%tt5= 4 : V17 7200 short train
%tt5= 5 : V17 7200 long train
%tt5= 6 : V17 9600 short train
%tt5= 7 : V17 9600 long train
%tt5= 8 : V17 12000 short train
%tt5= 9 : V17 12000 long train
%tt5= 10 : V17 14400 short train
%tt5= 11 : V17 14400 long train
34
Heritage Series ADSL Bridge/ Router
Appendix A
Appendix
35
Government
compliance notices
D.1 FCC compliance
This Broadband Sharing Router has been tested and found to comply with
the limits for a Class B personal computer and peripherals, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
unit does cause harmful interference to radio or television reception, which
can be determined by turning the unit off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Creator                         : 56TPC - Microsoft Word
Create Date                     : 2001:08:17 03:02:04
Title                           : 56TPC.PDF
Author                          : Lu
Producer                        : Acrobat PDFWriter 4.05Windows NT ª©
Modify Date                     : 2001:11:09 20:36:32+08:00
Page Count                      : 35

EXIF Metadata provided by EXIF.tools