Arista Networks W118 Wall Jack Access Point User Manual

Mojo Networks, Inc. Wall Jack Access Point Users Manual

Users Manual.PDF

W-118 Access Point
Quick Start Guide
Package Contents
You should have received the following components in your W118 package.
W118 Mounting Bracket
Mounting Accessories
x 2 x 2 x 2 x 2
Wall Mount: Mojo logo facing away from the wall
Mounting the W-118
Aix the mounting bracket on to the wall using the appropriate screws from the
mounting accessories included in the package.
Connect the cables to the appropriate ports in the rear-side of the device.
Mount the device on the bracket by
aligning the two notches on the bracket
with the two grooves on the rear panel of
the device. Slide the device and tighten it
onto the bracket with the screw provided
in the package.
Getting the W-118 Online
Step 1: Power up
If using PoE, plug one end of the Ethernet cable into the PoE switch or injector and plug
the other end into the WAN port (PoE) on the W118. Ensure that the PoE source you are
using is turned ON.
OR
As an alternative to PoE, insert the power adapter plug into an AC power outlet and the
other end into the power input port on the W118.
Warning: If not using PoE, make sure you use only an AC power adapter supported by
the W118 access point (AP).
Step 2: Connect to the network
If you are using PoE, then the W118
should already be connected to your
network. If you are not using PoE, then
plug one end of the Ethernet cable
into an Ethernet jack on your network
and the other end into the WAN port
(PoE) on the W118.
Step 3: Check the LED status
Wait for a few minutes till the
Power LED and Uplink LED turn GREEN
indicating that the W118 is online and
operational.
Troubleshooting
The following table provides the status of the device based on the LEDs.
After following these guidelines, if you are still unable to resolve the problem, contact the
local Mojo Networks Sales Engineer or 24/7 Mojo Networks Technical Support.
Tel: +1 (650) 641 0027 Email: support@mojonetworks.com
Mojo Networks, Inc. 339 N. Bernardo Avenue #200, Mountain View, CA 94043
T +1.877.424.7844 T 650.961.1111 F 650.961.1169 www.mojonetworks.com info@mojonetworks.com
© 2018 Mojo Networks, Inc. All rights reserved. Mojo Networks and the Mojo Networks logo are trademarks, and Mojo is a registered
trademark of Mojo Networks, Inc. All other trademarks mentioned herein are properties of their respective owners. Speciications are
subject to change without notice.
LED Status Description
Power Solid Green Power On
O Power O
Uplink Solid Green Device connected to LAN port 1 at 10/100/1000 Mbps
Blinking Green Activity on LAN port 1
5 GHz
Solid Green Client connected to 5 GHz radio
Blinking Green Wireless activity on 5 GHz radio
2.4 GHz Solid Green Client connected to 2.4 GHz radio
Blinking Green Wireless activity on 2.4 GHz radio
Radio 3 Blinking Green Activity on third radio
LAN1/2/3 Solid Green Device connected to LAN1/2/3 at 10/100/1000 Mbps
Blinking Green Activity on LAN1/2/3
If the AP is not able to connect to Mojo Wireless Manager, check the following:
1. Ensure that the Ethernet cable is plugged into the correct port on the W118 and the
other end of the cable is plugged into an Ethernet jack or port on a switch that is
turned ON.
2. If the W118 did not receive a valid IP address from the DHCP server, ensure that a
DHCP server is ON and available on the VLAN/subnet to which the AP is connected.
If the AP still fails to get a valid IP address, reboot it once to see if that resolves the
problem.
3. If you are using Mojo Cloud Services, ensure that Internet connectivity is available
from the VLAN/subnet to which the AP is connected. Check if the required ports for
AP and Server communication – UDP 3851 and default HTTP (TCP port 80) – are open
on the Firewall. If you are using a Proxy, Web accelerator or URL content iltering,
ensure the settings allow communication between the AP and Mojo Cloud Services.

Navigation menu