Aroot LK-P11B Mobile Printer User Manual LK P11 MANUAL 0710 indd

SEWOO TECH CO., LTD. Mobile Printer LK P11 MANUAL 0710 indd

User manual

All specifications are subject to change without noticeMOBILE PRINTERMODEL : LK-P11B
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.DISPOSE OF USED BATTERIES ACCORDING TO THE INSTURECITONS
23Table of Contents 1. Product overview 3 2. Unpacking4 3. Installation & Usage 5 3-1. Battery Installation 5 3-2. Battery Charging 6 3-3. Battery Charger Usage 7 3-4. Belt Strap Usage 8 3-5. Separation of Battery from the printer 9 3-6. Shoulder Strap Usage 10 3-7. Leather case Usage 11 3-8. Loading the paper 12 3-9. Control Panel Usage 13 3-10. Self Test 14 4. Peripherals Connection 16 4-1. Bluetooth Connection 16 4-2. Interface Cable Connection 17 5. Printer Cleaning 18 6. Product Specification 19 6-1. Specification 191. Product overviewPower switch CHARGER CONNECTOR Cover open button BatterySERIALUSB Paper feed button
452. Unpacking CD Printer case shoulder strap 3. Setting Up the Product3-1. Installing batteryInsert the battery inside printer as shown.Notes: As the battery is not charged at the time of your purchase, charge the battery prior to using the product. (Use the battery charger and/or the optional battery holder.) Push the Open to the direction as pointed by arrow in the image.1 2 3Quick ManualOpen the battery cover and push up the hook to the direction as above.Close the battery cover once you inserted the battery completely.StandardOptionPrinter BatteryRoll paperBelt BuckleUSB Shelded CableRecharger Serial Cable
673-2. Battery ChargingNotes: 1. Do not turn on the printer power while you are charging the battery.2. Do not print while charging the battery3. Do not connect the charger to the printer on the process of printing.3-3. Battery charger Usage1. Please press the battery into the holder until you can hear a snapping sound .2. Insert DC JACK ① into the end completely as the direct shown above.3. Plug the power code to electrical outlet.4. While charging the battery, red light turns on.Once the charge is completed, green light turns on.Check the state of code connection when error occurs blinking on red light.1. The battery can be charged only when the temperature is 0~40℃ 2. Be sure that the printer is turn off and the battery to be charged is installed.3. Connect the charger to the printer.4. Recharging will now be started.
893-4. Belt Hook UsageInsert the belt hook screw into the hole of the belt hook.As shown above, fasten the screw with a screw driver.3-5. Removing batteryPush the Open into the direction indicated with the arrow in the image.Pull out the battery as shown above. 1 21 2 3Push up the hook after opening the battery cover.
10113-6. Shoulder Strap Usage1 234Insert the strap into the hook on the printer. Place the end of strap into the hook of shoulder strap.After pulling out the end of strap tightly, put it into the clip to be fastened.Fasten the strap in the opposite side with the sample way.3-7. Leather Case Usage1 23Open the Velcro Put the printer into the leather case following the direction shown in the Close the Velcro
12133-9. Control Panel 3-8. Loading the media.1 234Press the cover open button and open Place the paper roll as shown.Make sure the paper is placed in right direction.Pull a short length of paper out of the printer and close the cover. Press Feed button and let the paper be arranged property for printing. Button Name functionPower buttonThis button is used to turn the printer on and off.When the printer is off, press this button for approximately 2 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off.Paper Feed ButtonPaper output can be done manually by pressing this button.Additionally, self-testing and Hexadecimal Dumping can be processed..1. Refer to “3-10” for self test information.2. Refer to the service manual regarding Hexadecimal Dumping.Battery Status Lamp1. If the Batt, LED are Lit, the battery is fully charged.2. If you can hear beeping sound and LED light is turned off, it means that the battery is at the lowest level.3. If the battery is not charged at all, the printer turns off automatically.Error Lamp If the red light is turned on, it means that the paper cover is open.
14153-10. Self TestYou can check the printer setting state by doing self test when you set the printer first time or encounter some problems.- Control Circuit, Mechanisms, Print Quality, Rom version.When you can not find the exact cause of problem through self test, investigate on other hardware parts or software. This function is independent of other devices and software.● Self –Test Instructions1.Turn the printer power off an close the printer paper cover.2. While pressing the paper feed button, turn on the printer power.3. The printout is producing4. To add a printout of the Hex-Dump mode, press the paper feed button once more.< Sample Printout of Self Test >
16174-1.Bluetooth Connection1. The printer can be connected to devices equipped with Bluetooth communication capacity (PDA, PC, etc.)2. Use the Bluetooth connection function supported by the device to connect to the printer.4. Peripherals Connection4-2. Interface Cable Connection1. Connect the interface cable to the cable connector of the printerNotes: Use only cables provided by this manufacturer 2. Connect the interface cable to the USB or Serial port of the device (PDA, PC, etc)SerialUSBThis product can communicate with other devises via Bluetooth communication and cable.
1819Printing Method Direct ThermalPrinting Speed 80mm/secResolution 203 DPI X 203 DPICharacter ALPHA NUMERIC Character, Extension CharacterBarcode Code 39, Code 93, UCC/EAN-128, Code 128, UPC-E, UPC-A, EAN-8, EAN-13, EAN-14, UPC and EAN 2 or 5 digit extensions, Plessey, FIM, Postnet, Interleaved 2-of-5, MSI, CodabarEmulation CPCLDriver Window CE 4.2&5.0, Window Mobile 5.0Sensor Black-mark, Gap, cover openPaper paper type Thermal Paperwidth 58mmthickness 65㎕External Diameter Max. Φ 56mmInternal Diameter 12.5mm +/-0.5mmReliability TPH 100kmCommunications standard Serial(RS-232C), USB, Bluetooth Class2option Wireless Lan *802.11b/gBattery Charger input AC100~240V, 50/6 Hzoutput 8.4V , 1200 mABattery Charger Battery type Li-onoutput 7.2V, 2400mAhCharging time 2 Time Size WXDXH(mm) 104 X 74 X 154WXDXH” 4.0 X 2.9 X 6.0Weight 500g6-1. Specification6. Pritner Specification5. Printer cleaningIf the interior of the printer is dusty, printing quality can lowered.In such a case, follow the instructions below to clean up the printer.NOTE1. Make sure to turn the printer power off prior to cleaning2. Regarding print head cleaning, as the print head sets very hot during printing, turn off the printer power and wait approximately 10 minute before commencement.3. When cleaning the print head, take care not to touch the heated portion of the print head. The print head subject to be damaged by static electricity.4. Take care not to allow the print head to become scratched and /or damaged in 1. Use an applicator swab moistened with an alcohol solution to clean the print head and remove any dusts.2. Once the cleaning is completed, insert paper roll into the printer few minutes later and close the printer cover.
Rev. 1.0SEWOO TECH CO.,LTD.ADDRESS Doosung Bd, 689-20, Kumjung-dong, Kunpo-si, Kyunggi-do, KoreaTEL 82-31-459-8200 FAX 82-31-459-8880URL http://www.miniprinter.com

Navigation menu