Aroot MP-300BT Mobile Printer User Manual LK P35B MANUAL 0910 indd

SEWOO TECH CO., LTD. Mobile Printer LK P35B MANUAL 0910 indd

User manual

23Table of Contents 1. Product Overview3 2. Unpacking4 3. Setting up the Product5 3-1. Installing Battery5 3-2. Battery Charging6 3-3. Loading the Media7 3-4. Black Mark8 3-5. Printer Case Usage9 3-6. Control Panel10 3-7. Self Test11 4. Peripherals Connection12 4-1. Bluetooth Connection12 4-2. Interface Cable Connection13 5. Printer Specification141. Product OverviewPower buttonPaper feed buttoncover open buttonDC POWER Battery SERIAL
452. UnpackingPRINTER BATTERY SERIAL CABLE ROLL PAPER CD MANUAL PRINTER CASE(OPTION) RECHARGER3. Setting up the Product3-1. Installing Battery1. Align the battery hook as shown in the picture.2. Push the battery into the printer until it locks in place.Notes As the battery is not charged at the time of your purchase, charge the battery prior to using the printer.
673-2. Battery Charging1. The battery can be charged only when the temperature is 0~40°C.2. Be sure that the printer is turn off and the battery to be charged is installed.3. Connect the charger to the printer.4. Recharging will now be started.3-3. Loading the Media1 234Press the cover open button. Place the paper roll as shown in the picture. (Make sure the paper is placed in right direction.)Pull a short length of paper out of the printer and close the cover as shown in the picture.Press feed button and let the paper be arranged properly for printing and cut the extra paper with tear bar. Notes 1. Do not turn on the printer power while you are charging the battery.2. Dot not print while charging the battery3. Do not connect the charger to the printer on the process of printing.
893-5. Printer Case Usage1 234Open the Velcro. Put the printer into the case following the direction as shown in the picture.Close the Velcro. Fix this case to the belt with using the belt buckle. 3-4. Black MarkNotes Black mark should be located on the opposite side of the printed side of the media.
10113-7. Self Test< Sample printout of Self Test> > 3-6. Control Panel**Sleep Mode**After 3 minutes without working, it changes to sleep mode automatically.Input Uart or serial data of Bluetooth. Notes The first 200ms’s data between sleep mode and warming-up could be ignored.You can check the printer setting state by doing self test when you set the printer first time or encounter some problems.- Control Circuit, Mechanisms, Print Quality, Rom version.When you can not find the exact cause of problem through self test, investigate on other hardware parts or software. This function is independent of other devices and software.● Self –Test Instructions1.Turn the printer power off an close the printer paper cover.2. While pressing the paper feed button, turn on the printer power.3. The printout is producing4. To add a printout of the Hex-Dump mode, press the paper feed button once more.5. To add a printout of ASCII pattern, press the paper feed button once more. (Without pressing the paper feed button, self test ends automatically)6.After ASCII pattern printing, self test ends automatically. Button Name functionPower buttonThis button is used to turn the printer on and off.When the printer is off, press this button for approximately 2 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off.Paper Feed ButtonPaper output can be done manually by pressing this button.Additionally, self-testing and Hexadecimal Dumping can be processed..1. Refer to “3-10” for self test information.2. Refer to the service manual regarding Hexadecimal Dumping.Battery Status Lamp1. If the Batt, LED are Lit, the battery is fully charged.2. If you can hear beeping sound and LED light is turned off, it means that the battery is at the lowest level.3. If the battery is not charged at all, the printer turns off automatically.Error Lamp If the red light is turned on, it means that the paper cover is open.
12134-2. Interface Cable Connection1. Connect the Interface cable (Serial / USB) to the cable connector of the printer.2. Connect the interface cable to the USB or Serial port of the device (PDA, PC, etc)Serial4-1. Bluetooth Connection1. The printer can be connected to devices equipped with Bluetooth communication capacity (PDA, PC, etc.).2. Use the Bluetooth connection function supported by the device to connect to the printer.Classifications DescriptionBluetooth Spec. Bluetooth V2.0 / Class2(10m)Frequency 2.4GHz ISM BANDBaudrate 115200bps Fixed. Data bit 8 Data bit Fixed. Parity bit No parity Fixed.Stop bit 1 Stop bit Fixed. 4. Peripherals ConnectionThis product can communicate with other devices via Bluetooth communication and cable.Notes Use only cables provided by this manufacturer

Navigation menu