Arris SVG2482AC User Manual SVG2482AC: Quick Start Guide QSG

User Manual: Arris SVG2482AC SVG2482AC: Quick Start Guide

Open the PDF directly: View PDF .
Page Count: 2

123

SVG2482AC

Wireless Voice Gateway

Quick Start Guide

The SURFboard SVG2482AC is a DOCSIS 3.0 telephony cable modem and

four-port Ethernet routing device with Wi-Fi and optional battery backup.

It uses DOCSIS 3.0 technology to provide ultra high-speed Internet

access. Using the connection capabilities of this home network gateway,

you can connect your network devices via the Ethernet ports or the two

wireless radios.

This quick start guide will help you to install your SVG2482AC and set up

a secure wireless network connection on your home or small business

network.

To customize your wireless network connection and other advanced

gateway settings, refer to the SURFboard SVG2482AC User Guide for more

information. The information listed below is available online at the ARRIS

Support website, www.arris.com/consumers:

•SVG2482AC User Guide

•Frequently asked questions (FAQs)

•Technical Support

•Additional ARRIS product information

For information on other ARRIS consumer products, please visit

www.SURFboard.com.

What You Should Know

In the Box

SVG2482AC

Wireless Voice

Gateway

Power Cord

Ethernet Cable

Software License &

Warranty Card

Support Information

Card

Quick Start Guide

Setting Up Your SVG2482AC Setting Up Your SVG2482AC (continued)

1. Connect the coaxial cable (connected to the cable wall outlet or to an

RF splitter) to the Cable connector on the rear of your

SVG2482AC.

Use your hand to tighten the connector.

2. Connect the Ethernet cable (included) to the Ethernet port on your

client device and to any open Ethernet port on the rear of your

SVG2482AC

.

Note: It is suggested that you use a client device (such as a laptop or

other device with an Ethernet input connector) to connect directly to your

SVG2482AC for the best performance when activating your SVG2482AC.

If a directly connected device is not available, you can connect using a

mobile device such as a wireless phone or tablet. Use the SSID (wireless

network name) and Wi-Fi Security Key (wireless network password) listed

on the SVG2482AC label.

3. Connect the power cord (included) to the Power port on the rear of

your SVG2482AC and then plug it into an electrical wall outlet that is

not controlled by a wall switch.

This automatically powers ON your

SVG2482AC.

4. Power ON your connected client device (e.g., laptop) and log on.

5. Check the front panel LEDs on your

SVG2482AC.

During startup, the Power, US/DS (Upstream/Downstream), and

Online LEDs will FLASH and then light up SOLID white. Both

Wireless LEDs will light up when your wireless devices are

connected.

Note: Your SVG2482AC will go online after the

Online LED stops ashing

and then lights up SOLID white.

It may take approximately ve to 10

minutes for your SVG2482AC to complete the online connection process.

Note: If you are a current voice subscriber with Comcast and purchased

the SVG2482AC, please call Comcast Customer Support at

1-855-OK-BEGIN (1-855-652-3446) to activate your SVG2482AC.

If you are a new voice subscriber with Comcast, continue with the

following steps to set up your new XFINITY telephony service account

and actiate your SVG2482AC.

6. Open a web browser and then type www.xnity.com/activate to

activate your SVG2482AC.

7. Follow the online instructions for entering your XFINITY account

information.

Afterwards, you will be prompted to set up the following information:

• XFINITY Account Login Name

• XFINITY Account Password

• Wi-Fi Network Name

• Wi-Fi Network Password

Note: Select Show More Settings if you want to set up separate network

names and passwords for the 2.4 GHz and 5 GHz wireless radios on your

SVG2482AC.

If you already have an existing Wi-Fi network and you are replacing

your router or gateway, ARRIS suggests that you use the same Wi-Fi

Network Name and Password that is currently set for your Wi-Fi

network.

Your Wi-Fi devices will automatically connect to your SVG2482AC

Wi-Fi network.

8. To check for Internet connectivity, open a web browser on your

device and then type a valid URL (such as www.SURFboard.com) in

the address bar and press Enter.

The ARRIS website should open. If it fails to open, please contact

your service provider to set up your Internet service or activate your

SVG2482AC.

Connecting Your Telephone

If you are migrating your current XFINITY Telephony service from an existing device,

your current phone service and phone number will be transferred to your SVG2482AC

after it is installed.

Note: Battery usage is optional, but it is available on the SVG2482AC for

Telephony back-up

only. Batteries are available for purchase online at the ARRIS SURFboard website,

shop.surfboard.com/arris-telephony-modem-back-up-batteries. For more information

on installing the battery, see Install the Battery in the SURFboard SVG2482AC User Guide.

1. Connect a telephone cord (not included) to the TEL LINE port on your telephone

and to the TEL 1 port on the rear of your

SVG2482AC

.

2. Check to make sure that your telephone has a dial tone

.

456

Connect to Your Wi-Fi Network

After installing your SVG2482AC, choose one of the following network

connection options:

•ConnectUsingYourMobileDevice

•ConnectUsingYourComputerorLaptop

•ConnectUsingtheWPSPairingButtonforYourWPS-EnabledDevice

Gateway Label

The SVG2482AC labels are located on the side and bottom of your

gateway. The following gateway information listed on the label may be

needed when contacting customer service:

•Model – Gateway model name

•S/N – Gateway serial number

•HFC MAC ID – Media Access Control (MAC) address

•SSID – Default wireless network name

•WI-FI SECURITY KEY – Default wireless network password

If the label is not

attached, please

refer to the bottom

of your gateway.

© 2017 ARRIS Enterprises, LLC. All rights reserved.

No part of this publication may be reproduced or transmitted in any form or by any

means without written permission from ARRIS Enterprises, LLC.

ARRIS, SURFboard, and the ARRIS logo are all trademarks or registered trademarks of ARRIS

Enterprises, LLC. Other trademarks and trade names may be used in this document to refer

to either the entities claiming the marks or the names of their products. ARRIS disclaims

proprietary interest in the marks and names of others.

ARSVD01721-c 03/2017

For future reference, if needed, write down the following online

account access and wireless network access information that you set

up during the SVG2482AC activation.

XFINITY Account Login Name:

XFINITY Account Password:

Gateway Login Password:

Wi-Fi Name: 2.4 GHz: 5 GHz:

Wi-Fi Password: 2.4 GHz: 5 GHz:

Network Access Information

Use the

SVG2482AC

Web Manager to set up and manage your wireless

gatewayandnetworksecuritycongurations.Toaccesstheweb

manager:

1. Open any web browser on your connected network device, then type

10.0.0.1 in the address bar, and press Enter.

2. Type the following default user name and password:

Username: admin

Password: password

3. Click LOGIN to open the

SVG2482AC

Web Manager.

Note: The message, You are using a default password, would you like to change

it?, will display. You can choose to either click OK to change the default password

or click Cancel to open the SVG2482AC Web Manager. Additional information for

changing the default password is available in the SVG2482AC User Guide (available

online at www.arris.com/consumers).

Use the Gateway Web Manager

Connect Using Your Mobile Device

Note: Some of the selections used in this procedure may vary slightly depending on your

device and operating system. Please make sure to choose the most applicable selections

on your device.

1. Access the Settings screen on your mobile device and then select one

of the following: WI-Fi, Wireless, or Connections.

2. Check that Wi-Fi or Wireless is set to ON.

Please note that for your Apple devices you may have to enter a

password and then select JOIN.

3. Select the SVG2482AC Wi-Fi Network name from the list of available

Wi-Fi networks to connect to your network.

4. EnteryourWi-FinetworkpasswordinthePasswordeldandselect

Connect.

This is the password that you set up during the SVG2482AC activation.

Connect Using Your Computer or Laptop

1. Locate the Wireless Network Connection icon on the taskbar of your device

screen.

Windows MAC

2. Click on the Network Connection icon for your device to view the list of

available wireless networks.

3. Locate and then click on the SVG2482AC Network name that you set

up during the SVG2482AC activation.

4. Click Connect and then at the prompt, enter your Wi-Fi network

passwordinthePasswordeld.

This is the network password that you set up during the SVG2482AC

activation.

5. Open a web browser on your computer.

6. Type a valid URL, such as www.SURFboard.com, in the web browser

address bar and press Enter.toconrmnetworkconnectivity.

Connect Using the WPS Pairing Button for Your WPS-Enabled

Device

Note: To use WPS, your device hardware must support WPS and also have WPA security

compatibiltiy.

1. Power ON your SVG2482AC and other WPS-enabled devices that you

want to connect to your wireless network

.

2. Press the WPS button located on the top of your SVG2482AC

.

3. Press and hold the WPS button on your WPS-enabled computer or

otherWPS-enableddeviceforveormoreseconds,andthenrelease

.

Front Panel LEDs

During normal operation, the Power, US/DS (Upstream/Downstream),

Online, and Tel1 (if connected) LEDs on the SVG2482AC front panel

should always be lit SOLID.

WPS Button

Power

US/DS

Online

2.4 GHz

5 GHz

Tel1

Tel2

Battery