Aruba Networks AP105SDR Aruba AP-105 Wireless Access Point User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1413870
Application ID	oRzUykCqzYziRAUjzECunw==
Document Description	Users Installation Guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	55.22kB (690268 bits)
Date Submitted	2011-02-04 00:00:00
Date Available	2011-02-18 00:00:00
Creation Date	2009-07-01 14:54:10
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2011-02-04 00:20:44
Document Title	untitled
Document Creator	FrameMaker 9.0

IAP-105 Wireless Access Point
Installation Guide
Power
Connector
The Aruba IAP-105 wireless access point supports the IEEE 802.11n standard for
high-performance WLAN. This access point uses MIMO (Multiple-in, Multipleout) technology and other high-throughput mode techniques to deliver highperformance, 802.11n 2.4 GHz and 5 GHz functionality while simultaneously
supporting existing 802.11a/b/g wireless services. The IAP-105 access point
works only in conjunction with an Aruba Controller.
ENET
AP Pre-Installation Checklist
Before installing your IAP-105 access point, be sure that you have the following:




1.25A
12V
Wireless transceiver
Protocol-independent networking functionality
IEEE 802.11a/b/g/n operation as a wireless access point
IEEE 802.11a/b/g/n operation as a wireless air monitor
Compatibility with IEEE 802.3af PoE
Central management configuration and upgrades through an Aruba
Controller
ENET

CONSOLE

AP105_002
Package Contents


CAT5 UTP cable of required length
One of the following power sources:
 IEEE 802.3af-compliant Power over Ethernet (PoE) source
 Supports full functionality for IAP-105
 The POE source can be any power source equipment (PSE) controller or
midspan PSE device
 Aruba AP AC-DC adapter kit (sold separately)
Aruba Controller provisioned on the network:
 Layer 2/3 network connectivity to your access point
 One of the following network services:
IAP-105 access point (1 unit or a pack of 10)
Installation guide (this document)

Aruba Discovery Protocol (ADP)

DNS server with an “A” record

DHCP Server with vendor-specific options
Console Port
Use the console port to connect to a terminal for direct local management.
1. Verify pre-installation connectivity.
Ethernet Port
2. Identify the specific installation location for each AP.
IAP-105 is equipped with a single 10/100/1000Base-T (RJ-45) auto-sensing, MDI/
MDX wired-network connectivity port. This port supports IEEE 802.3af Power
over Ethernet (PoE) compliance, accepting 48VDC as a standard defined
Powered Device (PD) from a Power Sourcing Equipment (PSE) such as a PoE
midspan injector, or network infrastructure that supports PoE.
3. Install each AP.
4. Verify post-installation connectivity.
5. Configure each AP.
If PoE is not available, an optional Aruba AP AC-DC adapter kit (sold separately)
can be used to power the IAP-105.
The reset button can be used to return the AP to factory default settings.. To
reset the AP:
AP105_005
1. Power off the AP.
2. Press and hold the reset button using a small, narrow object, such as a
paperclip.
3. Power-on the AP without releasing the reset button. The power LED will
flash within 5 seconds.
IAP-105 Hardware Overview
4. Release the reset button.
Figure 2 IAP-105 Front
The power LED will flash again within 15 seconds indicating that the reset is
completed. The AP will now continue to boot with the factory default settings.
Before You Begin
105
FCC Statement: Improper termination of access points installed in the
United States configured to non-US model controllers will be in violation of
the FCC grant of equipment authorization. Any such willful or intentional
violation may result in a requirement by the FCC for immediate termination
of operation and may be subject to forfeiture (47 CFR 1.80).
AP105_001
11B/G/N
11A/N
LEDs
The IAP-105 is equipped with four LEDs that indicate the status of the various
components of the AP.

Installing the AP
Service to all Aruba Networks products should be performed by trained
service personnel only.
PWR: Indicates whether or not the IAP-105 is powered-on
ENET: Indicates the status of the IAP-105’s Ethernet port
11A/N: Indicates the status of the 802.11a/n radio
11B/G/N: Indicates the status of the 802.11b/g/n radio
For information about the IAP-105’s LED behavior, see Table 1 on page 2.
Produit rĂŠseau local radio basse puissance operant dans la bande
frĂŠquence 2.4 GHz et 5 GHz. Merci de vous referrer au ArubaOS User
Guide pour les details des restrictions.
Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet.
Weitere Informationen bezlßglich Einschränkungen finden Sie im ArubaOS
User Guide.
Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare
riferimento alla ArubaOS User Guide per avere informazioni detagliate sulle
restrizioni.
Pre-Installation Network Requirements
After WLAN planning is complete and the appropriate products and their
placement have been determined, the Aruba controller(s) must be installed and
initial setup performed before the Aruba APs are deployed.
Using the Integrated Wall-Mounting Slots
The keyhole-shaped slots on the back of the AP can be used to attach the device
upright to an indoor wall or shelf. When you choose the mounting location, allow
additional space at the right of the unit for cables.
1. Since the ports are on the back of the device, make sure that you mount the
AP is such a way that there is a clear path to the Ethernet port, such as a predrilled hole in the mounting surface.
2. At the mounting location, install two screw on the wall or shelf, 1 7/8 inches
(4.7 cm) apart. If you are attaching the device to drywall, Aruba recommends
using appropriate wall anchors (not included).
Access points are radio transmission devices and as such are subject to
governmental regulation. Network administrators responsible for the
configuration and operation of access points must comply with local
broadcast regulations. Specifically, access points must use channel
assignments appropriate to the location in which the access point will be
used.
Figure 4 Installing the IAP-105 Access Point on a Wall
3. Align the mounting slots on the rear of the AP over the screws and slide the
unit into place (see Figure 4).
Verifying Pre-Installation Connectivity
Before you install APs in a network environment, make sure that the APs are
able to locate and connect to the controller after power on.
Specifically, you must verify the following conditions:
 When connected to the network, each AP is assigned a valid IP address
 APs are able to locate the controller
Refer to the ArubaOS Quick Start Guide for instructions on locating and
connecting to the controller.
Identifying Specific Installation Locations
EU Statement:
Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands.
Please refer to the ArubaOS User Guide for details on restrictions.

RF interference sources include:
 Microwave ovens and other 2.4 or 5 GHz objects (such as cordless phones)
 Cordless headset such as those used in call centers or lunch rooms
Aruba Networks, Inc., in compliance with governmental requirements, has
designed the IAP-105 access points so that only authorized network
administrators can change the settings. For more information about AP
configuration, refer to the ArubaOS Quick Start Guide and ArubaOS User
Guide.
Reset Button


Metal Objects—Metal pans between floors, rebar, fire doors, air conditioning/
heating ducts, mesh windows, blinds, chain link fences (depending on
aperture size), refrigerators, racks, shelves, and filing cabinets
Do not place an AP between two air conditioning/heating ducts. Make sure
that APs are placed below ducts to avoid RF disturbances.
Successful setup of an IAP-105 access point consists of five tasks, which must be
performed in this order:
DC Power Socket


Summary of the Setup Process
Figure 1 IAP-105
ENET
RF reflectors include:
Reset Button
Inform your supplier if there are any incorrect, missing, or damaged parts. If
possible, retain the carton, including the original packing materials. Use
these materials to repack and return the unit to the supplier if needed.
PWR
RF absorbers include:
 Cement/concrete—Old concrete has high levels of water dissipation, which
dries out the concrete, allowing for potential RF propagation. New concrete
has high levels of water concentration within the concrete, blocking RF
signals.
 Natural Items—Fish tanks, water fountains, ponds, and trees
 Brick
RF Radiation Exposure Statement: This equipment complies with FCC
RF radiation exposure limits. This equipment should be installed and
operated with a minimum distance of 13.78 inches (35 cm) between the
radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter
must not be co-located or operating in conjunction with any other antenna
or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this
device is restricted to indoor use to reduce the potential for harmful
interference with co-channel Mobile Satellite Systems.
You can mount the IAP-105 access point on a wall or on the ceiling. Use the AP
placement map generated by Aruba’s RF Plan software application to determine
the proper installation location(s). Each location should be as close as possible
to the center of the intended coverage area and should be free from obstructions
or obvious sources of interference. These RF absorbers/reflectors/interference
sources will impact RF propagation and should have been accounted for during
the planning phase and adjusted for in RF plan.
AP105_003


CONSOLE
The Aruba IAP-105 access point provides the following capabilities:

For initial setup of the controller, refer to the ArubaOS Quick Start Guide for
the software version installed on your controller.
Figure 3 IAP-105 Rear
Using the Integrated Ceiling Tile Rail Slots
The snap-in tile rail slots on the rear of the AP can be used to securely attach the
device directly to a 15/16" wide, standard ceiling tile rail.
Make sure the AP fits securely on the ceiling tile rail when hanging the
device from the ceiling; poor installation could cause it to fall onto people
or equipment.
1. Pull the necessary cables through a prepared hole in the ceiling tile near
where the AP will be placed.
2. If necessary, connect the console cable to the console port on the back of the
AP.
Hold the AP next to the ceiling tile rail with the ceiling tile rail mounting slots at
approximately a 30-degree angle to the ceiling tile rail (see Figure 5). Make sure
that any cable slack is above the ceiling tile.
Figure 5 Orienting the Ceiling Tile Rail Mounting Slots
Identifying Known RF Absorbers/Reflectors/Interference
Sources
Identifying known RF absorbers, reflectors, and interference sources while in
the field during the installation phase is critical. Make sure that these sources are
taken into consideration when you attach an AP to its fixed location.
AP105_004
About the Aruba IAP-105 Access Points
3. Pushing toward the ceiling tile, rotate the AP clockwise until the device clicks
into place on the ceiling tile rail.
Connecting Required Cables
Table 1 IAP-105 Series LED Meanings
LED
Color/State
Meaning
11A/N
Off
5 GHz radio is disabled
Install cables in accordance with all applicable local and national regulations and
practices.
Amber
᳝↦᳝ᆇ⠽䋼ໄᯢ
Hazardous Materials Declaration
䚼ӊৡ⿄
(Parts)
5 GHz radio enabled in
WLAN mode
⬉䏃ᵓ
(PCA Boards)
ᴎẄ㒘ӊ
Ethernet Ports
Green
The RJ45 Ethernet port (ENET) supports 10/100/1000Base-T auto-sensing MDI/
MDX connections. Use these ports to connect the AP to a twisted pair Ethernet
LAN segment or directly to an Aruba Controller. Use a 4- or 8-conductor,
Category 5 UTP cable up to 100 m (325 feet) long.
Green flashing
2.4 GHz radio disabled
The 10/100/1000 Mbps Ethernet port is on the back of the AP. The port has an RJ45 female connector with the pin-outs shown in Figure 6.
Amber
2.4 GHz radio enabled in
WLAN mode
Figure 6 Gigabit Ethernet Port Pin-Out
Green
2.4 GHz radio enabled in
11n mode
Green flashing
2.4 GHz Air Monitor or
RF Protect mode
RJ-45 Female
Pin-Out
Signal Name
Function
BI_DA+
BI_DABI_DB+
BI_DC+
BI_DCBI_DBBI_DD+
BI_DD-
Bi-directional pair +A
Bi-directional pair -A
Bi-directional pair +B
Bi-directional pair +C
Bi-directional pair -C
Bi-directional pair -B
Bi-directional pair +D
Bi-directional pair -D
Electrical
The serial console port (Console) allows you to connect the AP to a serial
terminal or a laptop for direct local management. This port is an RJ-45 female
connector with the pinouts described in Figure 7. Connect this port in one of the
following ways:
 Connect it directly to a terminal or terminal server using an Ethernet cable.
 Use a modular adapter to convert the RJ-45 (female) connector on the AP to a
DB-9 (male) connector, and connect the adapter to a laptop using an RS-232
cable. See Figure 8 for connector details of the adapter.
Figure 7 Serial Port Pin-Out

Ethernet:
 1 x 10/100/1000Base-T auto-sensing Ethernet RJ-45 Interfaces
 MDI/MDX
 IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab
(1000Base-T)
 Power over Ethernet (IEEE 802.3af compliant), 48V DC/350mA (see Figure
6 for pin configuration)
Power:
 12 VDC power interface, supports powering through an AC-to-DC power
adapter
Proper Disposal of Aruba Equipment
Ground
RxD
TxD
Direction
Input
Output
Power Connection
Ćť
Ćť
Ćť
Ćť
Ćť
Ćť
IAP-105 Wireless Access
Point
㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼ SJ/T11363-2006 ᷛ‫ޚ‬㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽ
Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is
below the relevant threshold of the SJ/T11363-2006 standard.
Installation Guide
This table shows where these substances may be found in the supply chain of electronic information
products, as of the date of sale of the enclosed product.
ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ
՟བ⬉∴ऩ‫ܗ‬῵ഫ 䌈೼݊ѻકϞ
ℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟‫ݠ‬Ё᠔㾘ᅮⱘᴵӊϟᎹ԰
The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are
per the symbol shown here. The Environment- Friendly Use Period is valid only when the
product is operated under the conditions defined in the product manual.
Safety and Regulatory Compliance
Contacting Aruba Networks
Aruba Networks provides a multi-language document that contains countryspecific restrictions and additional safety and regulatory information for all
Aruba access points. This document can be viewed or downloaded from the
following location: www.arubanetworks.com/safety_addendum.
Table 1
The device will be electronically labeled and the FCC ID will be displayed via the
controller WebUI under the About menu
RF Radiation Exposure Statement: This equipment complies with FCC
RF radiation exposure limits. This equipment should be installed and
operated with a minimum distance of 13.78 inches (35 cm) between the
radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter
must not be co-located or operating in conjunction with any other antenna
or transmitter. When operated in the 5.15 to 5.25 GHz frequency range, this
device is restricted to indoor use to reduce the potential for harmful
interference with co-channel Mobile Satellite Systems.
For the most current information about Global Environmental Compliance and
Aruba products, see our website at www.arubanetworks.com.
Waste of Electrical and Electronic Equipment
Aruba products at end of life are subject to separate collection
and treatment in the EU Member States, Norway, and
Switzerland and therefore are marked with the symbol shown
at the left (crossed-out wheelie bin). The treatment applied at
end of life of these products in these countries shall comply
with the applicable national laws of countries implementing
Directive 2002/96EC on Waste of Electrical and Electronic
Equipment (WEEE).
If both POE and DC power are available, the AP uses POE even when there
is not enough POE voltage available to power the AP.
Verifying Post-Installation Connectivity
The integrated LEDs on the AP can be used to verify that the AP is receiving
power and initializing successfully (see Table 1). Refer to the ArubaOS Quick
Start Guide for further details on verifying post-installation network
connectivity.
European Union RoHS
Aruba products also comply with the EU Restriction of
Hazardous Substances Directive 2002/95/EC (RoHS). EU
RoHS restricts the use of specific hazardous materials in
the manufacture of electrical and electronic equipment.
Specifically, restricted materials under the RoHS Directive are Lead (including
Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent
Chromium, and Bromine. Some Aruba products are subject to the exemptions
listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit
assemblies). Products and packaging will be marked with the “RoHS” label
shown at the left indicating conformance to this Directive.
China RoHS
Table 1 IAP-105 Series LED Meanings
LED
Color/State
Meaning
PWR
Off
No power to AP
Green flashing
System initializing
Red steady
System failed to
initialize, contact TAC
Green steady
Power on, device ready
Off
No link
Green on
1000 Mbps link
Amber on
10/100 Mbps link
Green flashing
Ethernet link activity
10
Aruba products also comply with China environmental declaration
requirements and are labeled with the “EFUP 10” label shown at
the left.
Web Site Support
Main Site
http://www.arubanetworks.com
Support Site
https://support.arubanetworks.com
Software Licensing Site
https://licensing.arubanetworks.com/login.php
Wireless Security Incident
Response Team (WSIRT)
http://www.arubanetworks.com/support/wsirt.php
Americas and APAC Support Email
support@arubanetworks.com
EMEA Support Email
emea.support@arubanetworks.com
WSIRT Email
Please email details of any security
problem found in an Aruba product.
wsirt@arubanetworks.com
Table 2

IEC 60601-1-2: 2007
EN 60601-1-2: 2007
This equipment has been tested and found to comply with the limits of the
standard for medical devices, IEC 60601-1-2:2007. The unit also complies with the
requirements of EN 60601-1-2:2007, providing the presumption of compliance to
the European Union’s Medical Device Directive 2007/47/EC. The limits are
designed to provide reasonable protection against harmful interference in a
typical medical installation. This equipment generates, uses and can radiate radio
frequency energy, and, if not installed and used in accordance with the
manufacturer’s instructions may cause harmful interference to other devices in
the vicinity. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment causes interference with other devices,
which may be determined by turning the equipment off and on, the user is
encouraged to try and correct the interference by one or more of the following
measures:


The IAP-105 has a single 12V DC power jack socket to support powering through
an AC-to-DC power adapter.
ENET
(10/100/1000 Mbps)
Ćť
ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼DŽ

DB-9 Male
Pin-Out
DB-9
Ćť
EMC Compliance and Warning Statement
For additional specifications on this product, please refer to the data sheet. The
data sheet can be found at www.arubanetworks.com.
Figure 8 RJ-45 (Female) to DB-9 (Male) Modular Adapter Conversion
RJ-45
TxD
GND
RxD
Ćť
Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials
in the parts is above the relevant threshold of the SJ/T11363-2006 standard.
If a power adapter other than the one provided by Aruba Networks is used
in the US or Canada, it should be cULus (NRTL) Listed, with an output
rated 12 VDC, minimum 1.25A, marked “LPS” or “Class 2,” and suitable for
plugging into a standard power receptacle in the US and Canada.
TxD
GND
GND
RxD
Internal
Connections
Ćť
h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7ᷛ‫ޚ‬㾘ᅮⱘ䰤䞣㽕∖DŽ
RJ-45 Female
Pin-Out
Direction
Input
Output
໮⒈Ѡ㣃䝮
3%'(

Serial
Console Port
∲
+J
Product Specifications
Serial Console Port
RJ-45 Female
Pin-Out
TxD
GND
RxD
Direction
Input
Output
(Mechanical Sub-Assemblies)
ƻ˖
5 GHz Air Monitor or RF
Protect mode
Off
1000Base-T Gigabit
Ethernet Port
11B/G/N
5 GHz radio enabled in
11n mode
᳝↦᳝ᆇ⠽䋼៪‫ܗ‬㋴(Hazardous Substance)
䬝
݁Ӌ䫀
໮⒈㘨㣃
&G
&U
3%%
䪙
3E


Reorient or relocate the device receiving the interference.
Increase the separation between the equipment.
Connect the equipment into an outlet on a circuit different from that to which
the other device(s) are connected.
Consult the manufacturer or field service technician for help.
The Model IAP-105 do not have an Applied Part as defined in IEC 60601-1. The
protection against electric shock is Class ll.
Telephone Support
Aruba Corporate
+1 (408) 227-4500
FAX
+1 (408) 227-4550
Copyright
Š 2010 Aruba Networks, Inc. AirWaveŽ, Aruba NetworksŽ, Aruba Mobility Management SystemŽ, Bluescanner,
For Wireless That WorksÂŽ, Mobile Edge Architecture, People Move. Networks Must Follow., RFProtectÂŽ, The All
Wireless Workplace Is Now Open For Business, and The Mobile Edge CompanyÂŽ are trademarks of Aruba
Networks, Inc. All rights reserved. All other trademarks are the property of their respective owners.
Open Source Code
Certain Aruba products include Open Source software code developed by third parties, including software code
subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other Open
Source Licenses. The Open Source code used can be found at this site:
http://www.arubanetworks.com/open_source
Legal Notice
The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate
other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for
this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against
it with respect to infringement of copyright on behalf of those vendors.
Warranty
This hardware product is protected by the Aruba Limited Lifetime warranty.
Altering this device (such as painting it) voids the warranty.
Device is not protected against ingress of liquids and has a protection class of
IPX0 as defined by IEC 60601-1 and IEC 60529. Equipment not suitable for use in
the presence of flammable mixtures.
The unit is considered “Continuous Operation” equipment as defined by IEC
60601-1.
Power Consumption – 48 VDC 802.3af power over Ethernet or 12VDC, 1.25A for
external AC supplied power (adapter sold separately); Maximum power
consumption – 12.5W.
Mechanical Dimensions: 132mm x 135mm x 45mm; 300g.
Environmental: Operating Temp: 0° C to +50° C (+32° F to +122° F); Humidity: 5
to 95% non-condensing. Storage Temp: -40° CS to +70° C (-40°F to +158°F).
www.arubanetworks.com
1344 Crossman Avenue
Sunnyvale, California 94089
Phone: 408.227.4500
Fax 408.227.4550
IAP-105 Wireless Access Point | Installation Guide
Part Number 0510860-01 | January 2011

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.2-c063 53.352624, 2008/07/30-18:12:18
Format                          : application/pdf
Title                           : untitled
Create Date                     : 2009:07:01 14:54:10Z
Creator Tool                    : FrameMaker 9.0
Modify Date                     : 2011:02:04 00:20:44+05:30
Metadata Date                   : 2011:02:04 00:20:44+05:30
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:ec2ec61d-c154-44ba-a44c-a912db36ad4c
Instance ID                     : uuid:70eadb67-29c0-4c12-8b2d-88f8af0d9ea1
Page Mode                       : UseNone
Page Count                      : 2
Creator                         : FrameMaker 9.0

EXIF Metadata provided by EXIF.tools