Aruba Networks AP85FXLX Aruba AP-85FX and AP-85LX Access Points User Manual AP 85IG 0510323 06

Aruba Networks, Inc. Aruba AP-85FX and AP-85LX Access Points AP 85IG 0510323 06

AP85FXLX User Manual PDF Download & Text

Users Manual

Download:
Mirror Download [FCC.gov]
Document ID	1035909
Application ID	Ufl8kwdJO6YBQ+KqRXcb1A==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	292.16kB (3651996 bits)
Date Submitted	2008-11-25 00:00:00
Date Available	2008-11-25 00:00:00
Creation Date	2008-11-24 13:46:39
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2008-11-24 16:40:53
Document Title	AP-85IG_0510323-06.book
Document Creator	FrameMaker 8.0
Document Author:	rsmall

Installation Guide
Aruba AP-85 Outdoor
Access Point Series
Copyright
© 2008 Aruba Networks, Inc. AirWave®, Aruba Networks®, Aruba Mobility Management System®, Bluescanner, For Wireless That
Works®, Mobile Edge Architecture®, People Move. Networks Must Follow®, RFprotect, The All Wireless Workplace Is Now Open For
Business, Green Island, and The Mobile Edge Company® are trademarks of Aruba Networks, Inc. All rights reserved. All other trademarks
are the property of their respective owners.
Open Source Code
Certain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU
General Public License (GPL), GNU Lesser General Public License (LGPL), or other Open Source Licenses. The Open Source code used
can be found at this site:
http://www.arubanetworks.com/open_source
Legal Notice
The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate other vendors’ VPN
client devices constitutes complete acceptance of liability by that individual or corporation for this action and indemnifies, in full, Aruba
Networks, Inc. from any and all legal actions that might be taken against it with respect to infringement of copyright on behalf of those
vendors.
Warranty
This hardware product is protected by the standard Aruba warranty of one year parts/labor. For more information, refer to the
ARUBACARE SERVICE AND SUPPORT TERMS AND CONDITIONS.
Altering this device (such as painting it) voids the warranty.
www.arubanetworks.com
1344 Crossman Avenue
Sunnyvale, California 94089
Phone: 408.227.4500
Fax 408.227.4550
Aruba AP-85 Outdoor Access Point Series | Installation Guide
0510323-06 | October 2008
Contents
Preface ................................................................................................................................... 5
Guide Overview .....................................................................................................5
Related Documents ...............................................................................................5
Contacting Aruba Networks ..................................................................................6
Chapter 1
AP-85 Series Hardware Overview .......................................................... 7
About the AP-85 Series .........................................................................................7
AP-85 Series Operation ..................................................................................7
Minimum Software Requirements .........................................................................8
Package Checklist .................................................................................................8
Hardware Model Overview ....................................................................................9
AP-85 Series Front View...........................................................................9
AP-85 Series Rear View............................................................................9
AP-85 Series Top View...........................................................................10
AP-85TX Bottom View ............................................................................10
AP-85FX/LX Bottom View.......................................................................11
LED Status Indicators ...................................................................................13
Optional Accessories...........................................................................................14
Chapter 2
Outdoor Planning and Deployment Considerations........................... 15
Planning and Deployment Considerations ..........................................................15
Scale Requirements ......................................................................................15
Identifying Known RF Absorbers/Reflectors/Interferences Sources ............15
RF Absorbers..........................................................................................15
RF Reflectors ..........................................................................................15
RF Interference Sources.........................................................................16
Line of Sight (Radio Path Planning)...............................................................16
Antenna Height .............................................................................................17
Antenna Position and Orientation .................................................................18
Radio Interference.........................................................................................19
Weather Conditions ......................................................................................19
Ethernet Cabling ...........................................................................................19
Grounding .....................................................................................................19
Chapter 3
AP-85 Series Installation....................................................................... 21
Pre-Installation Network Setup............................................................................21
Pre-Installation Checklist ..............................................................................21
Access Point Setup .............................................................................................21
Verifying Pre-Installation Connectivity ..........................................................22
Provisioning the AP.......................................................................................22
Installing the AP-85 .......................................................................................22
Mounting the AP-85 ...............................................................................23
Positioning the AP-85.............................................................................27
Connecting Required Cables..................................................................28
Lightning Arrestor Installation.................................................................31
Antenna Installation ................................................................................31
Verifying Post-Installation Connectivity ........................................................32
Aruba AP-85 Outdoor Access Point Series | Installation Guide
| 3
Configuring the AP-85...................................................................................32
Appendix A
Understanding Antennas ...................................................................... 33
Aruba Antennas ...................................................................................................33
Understanding Wireless Antennas ................................................................33
Omni-Directional vs. Directional Coverage ............................................33
Antenna Beamwidth, Pattern, and Gain Considerations ........................34
Understanding Antenna Pattern Plots and Specifications .....................36
Detachable Antenna Selection......................................................................37
Detachable Outdoor Antenna Types ......................................................37
Detachable Antenna Selection Tips........................................................37
Appendix B
Product Specifications.......................................................................... 43
Mechanical (AP-85TX, AP-85FX, and AP-85LX) ...........................................43
Electrical........................................................................................................43
AP-85TX .................................................................................................43
AP-85FX .................................................................................................44
AP-85LX..................................................................................................44
Maximum Power Draw ...........................................................................44
Wireless LAN.................................................................................................44
Safety and Regulatory Compliance .....................................................................45
Declaration of Conformity .............................................................................45
European Headquarters .........................................................................46
Instructions for Use in a Potentially Explosive Atmosphere ................................46
Proper Disposal of Aruba Equipment ..................................................................47
Waste of Electrical and Electronic Equipment ..............................................47
European Union RoHS ..................................................................................48
China RoHS ..................................................................................................48
Index ..................................................................................................................................... 49
4 |
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Preface
This preface includes the following information:
An overview of the contents of this manual
A list of related documentation for further reading
Aruba Networks support and service information
Guide Overview
Chapter 1, “AP-85 Series Hardware Overview” on page 7 provides a detailed hardware overview of the three AP-85
models: the AP-85TX, the AP-85FX, and the AP-85LX.
Chapter 2, “Outdoor Planning and Deployment Considerations” on page 15 provides key questions to ask and items to
consider when deploying an outdoor wireless network.
Chapter 3, “AP-85 Series Installation” on page 21 describes the multi-step process for successful installation and
deployment of an AP-85.
Appendix A, “Understanding Antennas” on page 33 provides key tools that will help you understand Aruba antenna
specifications.
Appendix B, “Product Specifications” on page 43 includes product technical specifications and safety and regulatory
compliance information.
Related Documents
The following documents are referred to in this guide and are considered components of the complete documentation set
needed for successful AP deployment and management:
ArubaOS Quick Start Guide
ArubaOS User Guide
Aruba Mobility Management System User Guide
Aruba Outdoor Antenna Specifications
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Preface | 5
Contacting Aruba Networks
Web Site Support
Main Site
http://www.arubanetworks.com
Support Site
https://support.arubanetworks.com
Software Licensing Site
https://licensing.arubanetworks.com/login.php
Wireless Security Incident
Response Team (WSIRT)
http://www.arubanetworks.com/support/wsirt.php
Support Emails
Americas and APAC
support@arubanetworks.com
EMEA
emea.support@arubanetworks.com
WSIRT Email
Please email details of any security
problem found in an Aruba product.
wsirt@arubanetworks.com
Telephone Support
Aruba Corporate
+1 (408) 227-4500
FAX
+1 (408) 227-4550
Support
United States
800-WI-FI-LAN (800-943-4526)
Universal Free Phone Service Number
(UIFN): Australia, Canada, China,
France, Germany, Hong Kong, Ireland,
Israel, Japan, Korea, Singapore, South
Africa, Taiwan, and the UK.
+800-4WIFI-LAN (+800-49434-526)
All Other Countries
+1 (408) 754-1200
6 | Preface
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Chapter 1
AP-85 Series Hardware
Overview
About the AP-85 Series
The AP-85 Series consists of resilient, environmentally hardened, outdoor rated, dual-band IEEE 802.11a/b/g devices, which
can be configured for deployment as a wireless access point, air monitor, mesh point, or mesh portal. This outdoor access
point series is part of Aruba’s comprehensive wireless network solution. The AP-85 Series works only in conjunction with an
Aruba Mobility Controller and each AP can be centrally managed, configured, and upgraded through the controller.
The AP-85 Series consists of the following models:
AP-85TX (Ethernet)
AP-85FX (Multi-mode Fiber)
AP-85LX (Single-mode Fiber)
AP-85 Series Operation
Wireless access point (IEEE 802.11 a/b/g)
Wireless air monitor (IEEE 802.11 a/b/g)
Wireless access point with wireless backhaul support*
Enterprise mesh point (MP; Mesh license required)*
Enterprise mesh portal (MPP; Mesh license required)*
Protocol-independent networking functionality
IEEE 802.3af Power over Ethernet (PoE) compatible (AP-85TX only)
NOTE
Items noted with a asterisk (*) require a secure enterprise mesh license. Contact your Aruba sales
representative for a complete listing of available software licenses.
Aruba access points must be installed by trained service personnel. These installers are responsible
for ensuring that grounding is available and it meets applicable local and national electrical codes.
CAUTION
Do not work on an AP and do not connect or disconnect cables during periods of lightning activity.
WARNING
Aruba AP-85 Outdoor Access Point Series | Installation Guide
AP-85 Series Hardware Overview | 7
Minimum Software Requirements
The AP-85 Series requires ArubaOS 3.2.0 or later.
ArubaOS software builds prior to version 3.2.0 do not support the AP-85 Series. If your network currently runs on a software
build prior to 3.2.0, you must upgrade the software on your master and local controllers to 3.2.0 or later prior to installing an
AP-85 in your existing network.
Package Checklist
Included with all three AP-85 models:
Aruba AP-85 outdoor access point (TX, FX, or LX model)
AP-85 wall/pole/mast mount kit (fixture with hardware)
8-foot DC outdoor rated power cable
Weatherproof connector shell for RJ-45 terminated CAT 5 cable

LTW P/N LTWRJS-00PFFA-SL8001
Aruba AP-85 Outdoor Access Point Installation Guide
Included with the AP-85FX/LX models only:
8-foot AC outdoor rated power cable (for FX/LX models only; US and EU options available)
Fiber Optic Termination Kit

AP-85FX: Tyco P/N 1828618-1

AP-85LX: Tyco P/N 1828618-2
NOTE
NOTE
Inform your supplier if any parts are incorrect, missing, or damaged. If possible, retain the carton,
including the original packing materials. Use these materials to repack and return the unit to the
supplier if needed.
Optional accessories are available for use with the AP-85 and are sold separately. Refer to "Optional
Accessories" on page 14 for further details.
8 | AP-85 Series Hardware Overview
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Hardware Model Overview
AP-85 Series Front View
The front of the AP-85 Series has LED status indicators (see Figure 1). For descriptions of the LEDs and their behavior, refer
to "LED Status Indicators" on page 13.
Figure 1 AP-85 Series Front View
arun_0100
LED
Status Indicators
AP-85 Series Rear View
The rear of the AP-85 Series has four mounting holes (see Figure 2). Refer to Chapter 3, “AP-85 Series Installation” on
page 21 for mounting and installation instructions.
Figure 2 AP-85 Series Rear View
Mounting Holes
Aruba AP-85 Outdoor Access Point Series | Installation Guide
AP-85 Series Hardware Overview | 9
AP-85 Series Top View
The top of the AP-85 Series consists of four, female N-type antenna interfaces (see Figure 3).
Figure 3 AP-85 Series Top View
Four, Female N-Type
Antenna Interfaces.
RADIO 0 supports 2.4 Ghz;
RADIO 1 supports 5 GHz
The AP-85 Series requires the use of detachable, outdoor rated antennas. Select the correct antenna type to support the
required frequency band (2.4 or 5 GHz) and the desired coverage pattern.
The four, female N-type antenna interfaces on the AP-85 models are grouped into diversity pairs, one pair is marked as
RADIO 0 and the other pair is marked as RADIO 1. RADIO 0 supports 2.4 GHz frequency band antennas and RADIO 1
supports 5 GHz frequency band antennas.
To select the correct antenna type for the deployment, download and read Aruba’s outdoor antenna specifications: http://
www.arubanetworks.com/products/access-points/antennas.php.
For further details, see Appendix A, “Understanding Antennas” on page 33.
CAUTION
An Aruba Lightning Arrestor, AP-LAR-1, must be installed on each antenna port for protection
against lightning induced surges. Failure to use an AP-LAR-1 can void the warranty of an Aruba
outdoor AP model and renders the AP susceptible to failure from lightning induced surges.
AP-85TX Bottom View
The bottom of the AP-85TX unit (see Figure 5) has the following ports and connections:
DC PWR 12 VDC, 2 A: The AP is capable of accepting DC power in the range of 8 to 16 VDC. If the AP-85TX is not
connected to a PoE source, the AP must be powered via a DC power source. An outdoor rated, two-wire, 8-foot long DC
power cable (wiring harness) is supplied with the unit. For proper installation instructions, see "DC and AC Power
Cables" on page 30.
LAN/POE 48 VDC, 350 mA: Also known as a 10/100Base-T Fast Ethernet (RJ-45) port, which is IEEE 802.3 BaseT and
802.3u 100BaseTX compliant. This port supports IEEE 802.3af Power over Ethernet (PoE), accepting 48 VDC as a
standards-defined powered device (PD) from a power sourcing equipment (PSE), such as a PoE midspan injector. The
AP-85TX also supports SPoE (Serial Power over Ethernet).
10 | AP-85 Series Hardware Overview
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Figure 4 10/100Base-T Fast Ethernet (RJ-45) Port Pin-Out
AP-85
10/100Base-T
Fast Ethernet (RJ-45)
RJ-45 Female
Pin-Out
Direction
Input
Output
ETH Tx+
ETH Tx–
ETH Rx+
Serial RxD**
Serial RGND**
ETH Rx–
Serial TxD**
Serial TGND**
(POE negative*)
(POE negative*)
(POE positive*)
(POE positive*)
(POE positive*)
(POE negative*)
*POE optional
**Serial optional
Grounding Point
CAUTION
It is important that the AP-85TX be properly grounded and a grounding point is provided on the
bottom of the AP-85TX model. A professional installer should ensure that grounding is available and
meets applicable local and national electrical codes.
Figure 5 AP-85TX Bottom View
Grounding Point
AP-85FX/LX Bottom View
The bottom of the AP-85FX/LX unit (see Figure 5) has the following ports and connections:
DC PWR 12 VDC, 2 A: The AP can accept DC power in the range of 8 to 16 VDC. If the AP-85FX/LX is not connected to an
AC power source, the AP must be powered by a DC power source. An outdoor rated, two-wire, 8-foot long DC power
cable (wiring harness) is supplied with the unit. For proper installation instructions, see "DC and AC Power Cables" on
page 30.
LAN - OPTICAL:

AP-85FX: This model has a 100BASE-FX data uplink port for multi-mode, dual-fiber network connectivity. A multimode, fiber patch cable with a duplex LC connector is required for use. The cable is not included and must be
purchased separately.

AP-85LX: This model has a 100BASE-LX data uplink port for single-mode, dual-fiber network connectivity. A singlemode, fiber patch cable with a duplex LC connector is required for use. The cable is not included and must be
purchased separately.
CONSOLE: A serial console port is provided for connection to a terminal, allowing direct local management.
Aruba AP-85 Outdoor Access Point Series | Installation Guide
AP-85 Series Hardware Overview | 11
Figure 6 Serial Console Port Pin-Out
Serial
Console Port
RJ-45 Female
Pin-Out
Direction
Input
Output
TxD
GND
GND
RxD
Communication settings for the serial console port are listed in Table 1.
Table 1 Console Terminal Settings
Baud Rate
Data Bits
Parity
Stop Bits
Flow Control
9600
None
None
AC PWR 90-228 V~, 500 mA: The AP can accept AC power at the limits specified on the unit. If the AP-85FX/LX is not
connected to a DC power source, the AP must be powered by an AC power source. An outdoor rated, three-wire, 8-foot
long AC power cable (wiring harness) is supplied with the unit. Some installation locations are in the scope and under
the authority of the National Electric Code (NEC or NFPA 70), and some are not, as indicated in Article 90.2. The NEC
applies where:

The product must be grounded reliably using the external screw, as shown in this installation guide, and not solely
depend on the ground provided in the power supply cord.

The power cord should be less than 15" long.

The plug for the power cord should be installed in a dry location, such as with the use of an NRTL listed receptacle
box with cover that is weatherproof with the power plug inserted into the receptacle (such as the MultiMac model
from Taymac Corp).
The NEC does not apply when:

The installation must follow all regulations and established practices that are applicable for the particular installation
environment.
For international outdoor use:

The product must be grounded reliably using the external screw, as shown in this installation guide, and not solely
depend on the ground provided in the power supply cord. Considerations should include selection of weatherproofing
means (IP67 or better), proper strain relieving for the power cord, and adherence to all applicable regulations and
local practices.

The plug for the power cord should be installed in a dry location, such as with the use of a suitable certified
receptacle box with a cover, which is weatherproof (IP67 or better) with the power plug inserted into the receptacle.
Grounding Point
CAUTION
It is important that the AP-85FX/LX be properly grounded; a grounding point is provided on the
bottom of the AP-85FX/LX model. The installer (trained service personnel) should ensure that
grounding is available and that the grounding meets applicable local and national electrical codes.
12 | AP-85 Series Hardware Overview
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Figure 7 AP-85FX/LX Bottom View
Grounding Point
LED Status Indicators
All AP-85 models include visual indicators for power, link, and radio status. Additionally, each radio has a seven-LED array
that indicates received signal strength (RSSI).
NOTE
The RSSI LED indicators represent varying degrees in the RSSI level. The absence of a signal is
indicated by no LED response, and full signal strength is indicated when all seven LEDs are active
and lit.
Table 2 lists the meanings of the LEDs on the AP-85 outdoor access points.
Table 2 AP-85 LED Status Indicators
LED
Function
Indicator
Status
PWR
AP Power/Ready
Status
Off
No power to AP
Flashing
Device booting, not ready
On
Device ready
Off
Ethernet link unavailable
On (Yellow)
10 Mbs Ethernet link negotiated
On (Green)
100 Mbs Ethernet link negotiated
Blinking
Traffic on Ethernet link
Off
Ethernet link unavailable
On (Green)
100 Mbs Ethernet link negotiated
Blinking
Traffic on Ethernet link
Off
Radio 0 disabled
On (Green)
Radio 0 enabled in WLAN mode
Off
Radio 1disabled
On (Green)
Radio 1 enabled in WLAN mode
LINK/ACT
(applicable to the
AP-85TX only)
LAN/Network Link
Status
LINK/ACT
LAN/Network Link
(applicable to the
Status
AP-85FX/LX models only)
RADIO 0
RADIO 1
Radio 0 Status
Radio 1 Status
Aruba AP-85 Outdoor Access Point Series | Installation Guide
AP-85 Series Hardware Overview | 13
Table 2 AP-85 LED Status Indicators (Continued)
LED
Function
Indicator
Status
RSSI (Radio 0)
RSSI Level for
Radio 0
Off
RSSI disabled/no signal
7 Step Progressive
Bars
Each bar represents a progressive
increase in signal strength, with 7
bars representing maximum signal
strength (100%).
Minimum data rate: Two lit LEDs
Maximum data rate: Six lit LEDs
3/6/9/12/15/21/27 dB
RSSI
RSSI (Radio 1)
RSSI Level for
Radio 1
Off
RSSI disabled/no signal
7 Step Progressive
Bars
Each bar represents a progressive
increase in signal strength, with 7
bars representing maximum signal
strength (100%).
Minimum data rate: Two lit LEDs
Maximum data rate: Six lit LEDs
3/6/9/12/15/21/27 dB
RSSI
Optional Accessories
The following items are available for use with AP-85 outdoor access points and are sold separately. Contact your Aruba sales
representative for details and assistance.
Aruba 85 Field Replaceable Mount Kit: P/N AP-85-MNT-S
Aruba 85 Low-Profile Wall Mount Bracket: P/N AP-85-MNT-2
Aruba 85 Streetlight Power Tap Adapter (8 ft): P/N AP-85-PT-1
Aruba 85 AC Power Provisioning Cable (3 ft; indoor rated): P/N AP-85-CBL-1
Aruba 85 Antenna Mount Bracket: P/N AP-85-MNT-1
Aruba 85 AC Power Cable (8 ft): P/N AP-85-CBL-2-US-S or AP-85-CBL-2-EU-S
Aruba 85 AC Power Cable (40 ft): P/N AP-85-CBL-3-US-S or AP-85-CBL-3-EU-S
Aruba 85 DC Power Cable (8 ft): P/N AP-85-CBL-4-S
Aruba Lightning Arrester: P/N AP-LAR-1
AC power cables are available for use with the AP-85FX/LX models only.
NOTE
14 | AP-85 Series Hardware Overview
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Chapter 2
Outdoor Planning and
Deployment Considerations
Planning and Deployment Considerations
Prior to deploying an outdoor wireless network, the environment must be evaluated to plan for a successful Aruba WLAN
deployment. Successfully evaluating the environment enables the proper selection of Aruba APs and antennas and assists in
the determination of their placement for optimal RF coverage. This process is considered WLAN or RF planning and Aruba’s
system engineers can assist in the outdoor planning process.
Scale Requirements
The potentially immense scale of outdoor deployments requires consideration of factors that may not be as important in a
typical indoor deployment:
Range (distance): Range or distance between APs must be taken into account during the planning phase. Available AP
mounting locations are often far less flexible in an outdoor environment. Regardless of these outdoor restrictions, the
desired goal is to achieve results similar to an indoor deployment: a “dense” RF deployment that supports advanced
Aruba features, such as ARM, efficient client roaming, and failover.
Elevation: Proper consideration and planning for elevation differences between APs (AP to AP) and AP to Client can be
critical to success. To plan for these differences in elevation, it is important to understand the 3D coverage pattern
provided by the antennas that will be deployed in the environment.
Non-Fixed Considerations: The RF environment might change on a day to day basis. Keep non-fixed items, such as
shipping containers, vehicles, and future building construction, in mind when planning for an outdoor deployment.
Identifying Known RF Absorbers/Reflectors/Interferences Sources
Identifying known RF absorbers/reflectors/interference sources while out in the field during the installation phase is critical.
Even though outdoor environments consist of fewer RF absorbers/reflectors/interference sources compared to indoor
environments, ensure that these sources are identified and taken into consideration when installing and mounting an AP to
its fixed outdoor location.
RF Absorbers
Cement/Concrete
Natural Items: Trees/vegetation
Brick
RF Reflectors
Metal Objects: Roof-installed air-conditioning equipment, chain link fences (depending on aperture size), other wire
fences, or water pipes
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Outdoor Planning and Deployment Considerations | 15
RF Interference Sources
Other 802.11a/b/g or broadband access equipment operating nearby
Industrial RF welding equipment or other Industrial, Scientific and Medical (ISM) equipment that utilizes RF to heat or
alter the physical properties of materials
Military, Commercial Aviation or Weather Radar Systems
Line of Sight (Radio Path Planning)
AP-85 Series access points are capable of performing as one of the following:
Enterprise mesh point (MP)
Enterprise mesh portal (MPP)
NOTE
To configure the AP-85 as a mesh point or mesh portal, you must install a mesh software license on
a Mobility Controller as a software license key. Contact your sales account manager or authorized
reseller to obtain the software license. There are several mesh software licenses available that
support different maximum number of APs. The licenses are cumulative; each additional license
installed increases the number of APs (mesh nodes) supported by the Mobility Controller.
A wireless bridge or mesh link requires a “radio line of sight” between the two antennas for optimum performance. The
concept of radio line of sight involves the area along a link through which the bulk of the radio signal power travels. This
area is known as the first Fresnel Zone of the radio link. For a radio link, no object (including the ground) must intrude
within 60% of the first Fresnel Zone.
Figure 8 illustrates the concept of a good radio line of sight.
Figure 8 Line of Sight
Radio Line of Sight
Visual Line of Sight
If there are obstacles in the radio path, there may still be a radio link but the quality and strength of the signal will be
affected. Calculating the maximum clearance from objects on a path is important as it directly affects the decision on
antenna placement and height. It is especially critical for long-distance links, where the radio signal could easily be lost.
When planning the radio path for a wireless bridge or mesh link, consider these factors:
Avoid any partial line of sight between the antennas
Be cautious of trees or other foliage that may be near the path, or may grow and obstruct the path.
Be sure there is enough clearance from buildings and that no building construction may eventually block the path.
For very long distance links, the curvature of the earth (20 cm per km) may need to be considered in the calculation of
relative heights.
16 | Outdoor Planning and Deployment Considerations
Aruba AP-85 Outdoor Access Point Series | Installation Guide
z
Check the topology of the land between the antennas using topographical maps, aerial photos, or even satellite image
data (software packages are available that may include this information for your area)
Avoid a path that may incur temporary blockage due to the movement of cars, trains, or aircraft.
Antenna Height
A reliable wireless bridge or mesh link is usually best achieved by mounting the antennas at each end high enough for a clear
radio line of sight between them. The minimum height required depends on the distance of the link, obstacles that may be in
the path, topology of the terrain, and the curvature of the earth (for links over 3 miles).
For long-distance links, the AP may have to be mounted on masts or poles that are tall enough to attain the minimum
required clearance. Use the following table to estimate the required minimum clearance above the ground or path
obstruction (for 5 GHz bridge links).
Table 3 Antenna Minimum Height and Clearance Requirements
Total Link Distance
Max Clearance for
60% of First Fresnel
Zone at 5.8 GHz
Approximate Clearance
for Earth Curvature
Total Clearance
Required at
Mid-point of Link
0.25 mile (0.402 km)
4.6 ft (1.4 m)
0.007 ft (0.002 m)
4.6 ft (1.4 m)
0.5 mile (0.805 km)
6.2 ft (1.9 m)
0.03 ft (0.010 m)
6.2 ft (1.9 m)
1 mile (1.6 km)
8.9 ft (2.7 m)
0.13 ft (0.04 m)
8.9 ft (2.7 m)
2 miles (3.2 km)
12.5 ft (3.8 m)
0.5 ft (0.15 m)
13.1 ft (4.0 m)
3 miles (4.8 km)
15.4 ft (4.7 m)
1.0 ft (0.3 m)
16.4 ft (5.0 m)
4 miles (6.4 km)
17.7 ft (5.4 m)
2.0 ft (0.6 m)
19.7 ft (6.0 m)
5 miles (8 km)
20 ft (6.1 m)
3.0 ft (0.9 m)
23 ft (7.0 m)
7 miles (11.3 km)
23.6 ft (7.2 m)
6.2 ft (1.9 m)
30 ft (9.1 m)
9 miles (14.5 km)
27 ft (8.2 m)
10.2 ft (3.1 m)
37 ft (11.3 m)
12 miles (19.3 km)
30.8 ft (9.4 m)
18.0 ft (5.5 m)
49 ft (14.9 m)
15 miles (24.1 km)
34.4 ft (10.5 m)
28.0 ft (8.5 m)
62.7 ft (19.1 m)
NOTE
To avoid any obstruction along the path, the height of the object must be added to the minimum
clearance required for a clear radio line of sight. Consider the following simple example, illustrated in
Figure 9.
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Outdoor Planning and Deployment Considerations | 17
Figure 9 Antenna Height and Line of Sight
Radio Line of Sight
Visual Line of Sight
3 miles (4.8 km)
2.4 m
5.4 m
1.4 m
9m
20 m
17 m
12 m
A wireless bridge or mesh link is deployed to connect building A to building B, which is located three miles (4.8 km) away.
Mid-way between the two buildings is a small tree-covered hill. From the above table it can be seen that for a three-mile link,
the object clearance required at the mid-point is 5.3 m (17.4 ft). The tree tops on the hill are at an elevation of 17 m (56 ft), so
the antennas at each end of the link need to be at least 22.3 m (73 ft) high. Building A is six stories high, or 20 m (66 ft), so a
2.3 m (7.5 ft) mast or pole must be constructed on its roof to achieve the required antenna height. Building B is only three
stories high, or 9 m (30 ft), but is located at an elevation that is 12 m (39 ft) higher than building A. To mount an antenna at
the required height on building B, a mast or pole of 1.3 m (4.3 ft) is needed.
Never construct a radio mast, pole, or tower near overhead power lines.
CAUTION
NOTE
Local regulations may limit or prevent construction of a high radio mast or tower. If your wireless
bridge or mesh link requires a high radio mast or tower, consult a professional contractor for advice.
Antenna Position and Orientation
Once the required antenna height has been determined, other factors affecting the precise position of the wireless bridge or
mesh link must be considered:
Be sure there are no other radio antennas within 2 m (6 ft) of the wireless bridge or mesh link. These include other WiFi
radio antennas.
Place the wireless bridge or mesh link away from power and telephone lines.
Avoid placing the wireless bridge or mesh link too close to any metallic reflective surfaces, such as roof-installed airconditioning equipment, tinted windows, wire fences, or water pipes. Ensure that there is at least 5 feet clearance from
such objects.
The wireless bridge or mesh link antennas at both ends of the link must be positioned with the same polarization
direction, either horizontal or vertical. Proper alignment helps to maximize throughput.
18 | Outdoor Planning and Deployment Considerations
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Radio Interference
The avoidance of radio interference is an important part of wireless link planning. Interference is caused by other radio
transmissions using the same or an adjacent channel frequency. You should first scan your proposed site using a spectrum
analyzer to determine if there are any strong radio signals using the 802.11a/b/g channel frequencies. Always use a channel
frequency that is furthest away from another signal.
If radio interference is still a problem with your wireless bridge or mesh link, changing the antenna direction may improve
the situation.
Weather Conditions
When planning wireless bridge or mesh links, you must take into account any extreme weather conditions that are known to
affect your location. Consider these factors:
Temperature: The wireless bridge or mesh link is tested for normal operation in temperatures from
-. Operating in temperatures outside of this range may cause the unit to fail
Wind Velocity: The wireless bridge or mesh link can operate in winds up to. You must consider the known maximum
wind velocity and direction at the site and be sure that any supporting structure, such as a pole, mast, or tower, is built to
withstand this force.
Lightning: Rain: The wireless bridge or mesh link is weatherproofed against rain. However, it is recommended to apply
CAUTION
An Aruba Lightning Arrestor, AP-LAR-1, must be installed on each antenna port for protection
against lightning induced surges. Failure to use an AP-LAR-1 can void the warranty of an Aruba
outdoor AP model and renders the AP susceptible to failure from lightning induced surges.
weatherproof sealing tape around the Ethernet port and antenna connectors for extra protection. If moisture enters a
connector, it may cause a degradation in performance or even a complete failure of the link.
Snow and Ice: Falling snow, like rain, has no significant effect on the radio signal. However, a buildup of snow or ice on
antennas may cause the link to fail. In this case, the snow or ice has to be cleared from the antennas to restore operation
of the link.
Ethernet Cabling
When a suitable antenna location has been determined, you must plan a cable route from the wireless bridge or mesh link
outdoors to a suitable power and/or network source.
Consider these points:
The Ethernet cable length should never be longer than 90 m (295 ft).
Determine a building entry point for the cable (if applicable).
Determine if conduits, bracing, or other structures are required for safety or protection of the cable.
For lightning protection at the power injector end of the cable, consider using a lightning arrestor immediately before the
cable enters the building
Grounding
It is important that the wireless bridge or mesh link, cables, and any supporting structures are properly grounded. Each AP85 Series access point includes a grounding screw for attaching a ground wire. Be sure that grounding is available and that it
meets local and national electrical codes. Ground the access point first using the external ground stud on the unit before
making any other connection.
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Outdoor Planning and Deployment Considerations | 19
20 | Outdoor Planning and Deployment Considerations
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Chapter 3
AP-85 Series Installation
Pre-Installation Network Setup
When WLAN planning is complete and the appropriate products and their placement have been determined, the Aruba
Mobility Controller(s) must be installed and initial setup performed before the Aruba Outdoor Access Points. are deployed.
For initial setup of the Mobility Controller, refer to the ArubaOS Quick Start Guide for the software version installed on
your controller.
Pre-Installation Checklist
Before installing your AP-85, be sure that you have the items listed in Table 4.
Table 4 AP-85 Pre-Installation Checklist
AP-85TX
AP-85FX/LX
Fast Ethernet (FE) cable of required length
IEEE 802.3af compliant PoE source (Aruba
Mobility Controller or Midspan device) or DC
power source
Aruba Mobility Controller configured and
installed on the network
Layer 2/3 network connectivity to your AP-85
One of the following network services:
1. Aruba Discovery Protocol (ADP)
2. DNS server with an “A” record
3. DHCP Server with vendor specific options
Fiber patch cable of required length:
1. Single-mode fiber patch cable for the AP-85LX
2. Multi-mode fiber patch cable for the AP-85FX
AC or DC power source
Aruba Mobility Controller configured and installed
on the network
Layer 2/3 network connectivity to your AP-85
One of the following network services:
1. Aruba Discovery Protocol (ADP)
2. DNS server with an “A” record
3. DHCP Server with vendor specific options
Access Point Setup
NOTE
It is important that you follow the guidelines in the previous section, "Pre-Installation Network
Setup" on page 21, before attempting to set up and install an AP-85.
Successful setup of an AP-85 consists of five tasks, which must be performed in the following order:
1. Verify pre-installation connectivity
2. Provision the AP-85
3. Install the AP-85
4. Verify post-installation connectivity
5. Configure the AP-85
Aruba AP-85 Outdoor Access Point Series | Installation Guide
AP-85 Series Installation | 21
NOTE
CAUTION
Aruba Networks, in compliance with governmental requirements, has designed the AP-85 such that
only authorized network administrators can change configuration settings. For more information
about AP configuration, refer to the ArubaOS Quick Start Guide and ArubaOS User Guide.
Access points are radio transmission devices and as such are subject to governmental regulation.
Network administrators responsible for the configuration and operation of access points must
comply with local broadcast regulations. Specifically, access points must use channel assignments
appropriate to the location in which the access point will be used.
Verifying Pre-Installation Connectivity
Before you install APs in a network environment, make sure that the APs will be able to locate and connect to the Mobility
Controller when they are powered on.
Specifically, you must verify the following conditions:
When connected to the network, each AP is assigned a valid IP address.
APs can locate the Mobility Controller (Mobility ControllerDiscovery).
Refer to the ArubaOS Quick Start Guide for instructions on locating and connecting to the Mobility Controller.
Provisioning the AP
Each AP has unique provisioning parameters. These local AP parameters are initially configured on the Mobility Controller.
The Mobility Controller pushes the parameters out to the specific AP, where they are stored. Aruba recommends that you
configure the provisioning settings using the ArubaOS Web UI only. Refer to the ArubaOS User Guide for complete details.
NOTE
If the AP-85 is to be deployed in a mesh networking environment, the AP-85 must be provisioned as
a mesh portal or a mesh point before deployment.
Installing the AP-85
CAUTION
CAUTION
22 | AP-85 Series Installation
RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits.
This equipment should be installed and operated with a minimum distance of 13.8 inches (35 cm)
between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
Aruba Access Points, AP-LAR-1 lightning arresters, and cable termination kits must be installed by
trained service personnel. These installers are responsible for ensuring that grounding is available
and that grounding meets applicable local and national electrical codes.
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Do not work on an AP and do not connect or disconnect cables during periods of lightning activity.
WARNING
Mounting the AP-85
Preparing the AP-85 for Installation
1. Install the provided mounting bolts (M8 bolts with captive flat washer) into the four mounting holes on the rear of the
AP-85 (see Figure 10). Leave approximately two to three threads showing on each mounting bolt.
Figure 10 Installing the Mounting Bolts
Mounting Holes
Mounting Bolts
(M8 bolts, 4x)
Wall Mounting the AP-85
To wall mount an AP-85:
1. Secure the mounting plate to a flat wall using the appropriate screws and anchors for your mounting application (see
Figure 11).
NOTE
Wall mount hardware is not included with the mounting plate and must be purchased separately for
your mounting application. The mounting plate accepts the following screw or bolt sizes: M4, M5,
SAE #8, and SAE #10.
Aruba AP-85 Outdoor Access Point Series | Installation Guide
AP-85 Series Installation | 23
Figure 11 Attaching the Mounting Plate
Wall
Mounting Plate
Screws (4x)
Anchors (4x)
2. Seat the AP-85 into the four keyholes on the mounting plate and tighten down the four mounting bolts (M8 bolts) to
secure the AP-85 in place (see Figure 12). The mounting plate should rest between the captive flat washer on each
mounting bolt and the rear of the AP-85.
NOTE
Figure 12 shows the AP-85 installed with the antenna jacks at the top of the unit. To install the AP85 with the antenna jacks at the side, rotate the unit 90 degrees before seating the unit on the
mounting plate.
Figure 12 Wall Mounting the AP-85
Mounting Plate
AP-85
Mounting Bolts
Wall
arun_0127A
Pole Mounting the AP-85 (1.5-inch to 3.5-inch Diameter)
To attach an AP-85 to a pole with a diameter of 1.5 inches to 3.5 inches:
1. Assemble the pole mounting bracket:
a. Slide the long T-bolt through the opening in the mounting bracket (see Figure 13).
b. Attach the provided retaining clip to the T-bolt (see Figure 13).
c. Screw the provided nut onto the end of the T-bolt (see Figure 13).
24 | AP-85 Series Installation
Aruba AP-85 Outdoor Access Point Series | Installation Guide
2. Secure the mounting plate to the mounting bracket using the four provided Phillips screws (see Figure 13).
Figure 13 Assembling the Pole Mounting Bracket
Mounting Plate
Mounting Bracket
Phillips Screws (4x)
arun_0137
Retaining Clip
T-Bolt (1x)
Nut (1x)
3. Attach the pole mounting bracket assembly to a 1.5-inch to 3.5-inch diameter pole and secure the bracket in place (see
Figure 14).
a. Wrap the pole mounting bracket around the pole.
b. Slip the end of the T-bolt with nut through the opening in the pole mounting bracket.
c. Maneuver the T-bolt to the top slot in the pole mounting bracket and tighten down the nut. Verify that the nut is tightly
secured and that the bracket cannot move. It must be secure to support the weight of the AP-85.
Figure 14 Attaching the Pole Mounting Bracket
arun_0129
Step B
Step A
arun_0130
arun_0130
Step C
4. Seat the AP-85 into the four keyholes on the mounting plate and tighten the four mounting bolts (M8 bolts) to secure the
AP-85 in place (see Figure 15 and Figure 16). The mounting plate should rest between the captive flat washer on each
mounting bolt and the rear of the AP-85.
NOTE
The pole mounting bracket can be secured to a horizontal or vertical pole. The position of the
keyholes on the mounting plate allows you to mount the AP-85 on either pole type with the antenna
jacks at the top or the side. To mount the AP-85 with the antenna jacks at the side, rotate the unit 90
degrees before seating the unit on the mounting plate.
Aruba AP-85 Outdoor Access Point Series | Installation Guide
AP-85 Series Installation | 25
Figure 15 Vertical Pole Mount Position (1.5-inch to 3.5-inch Diameter Pole)
Tightened Mounting Bolts
AP-85
Secured
Mounting Bracket
arun_0131B
Figure 16 Horizontal Pole Mount Position (1.5-inch to 3.5-inch Diameter Pole)
AP-85
Secured
Mounting Bracket
Tightened Mounting
Bolts
arun_0131C
Pole Mounting the AP-85 (Pole Diameter Greater than 3.5-inches)
To attach an AP-85 to a pole with a diameter greater than 3.5 inches:
1. Attach the mounting plate to the pole using outdoor rated straps (see Figure 17). Outdoor rated straps are not included
with the unit and must be purchased separately.
2. Seat the AP-85 into the four keyholes on the mounting plate and tighten down the four mounting bolts (M8 bolts) to
secure the AP-85 in place (see Figure 17). The mounting plate should rest between the captive flat washer on each
mounting bolt and the rear of the AP-85.
26 | AP-85 Series Installation
Aruba AP-85 Outdoor Access Point Series | Installation Guide
The mounting plate can be secured to a horizontal or vertical pole. The position of the keyholes on
the mounting plate allows you to mount the AP-85 on either pole type with the antenna jacks at the
top or the side. To mount the AP-85 with the antenna jacks at the side, rotate the unit 90 degrees
before seating the unit on the mounting plate.
NOTE
Figure 17 Pole Mounting the AP-85 (Diameter Greater than 3.5 Inches)
AP-85
Mounting Bolts
Mounting Plate
Outdoor-Rated Straps
arun_0135A
Positioning the AP-85
To adjust the angle of an AP-85 on a vertical pole:
1. Loosen the four M8 bolts on the side of the mounting plate. Rotate the AP to the desired angle and tighten down the M8
bolts (see Figure 18).
Figure 18 Positioning the AP-85 on a Vertical Pole
M8 Positioning Bolts
(4x, 2x per side)
To adjust the angle of an AP-85 on a horizontal pole:
1. Rotate the entire mounting bracket to the desired angle and tighten the bracket into place (see Figure 19).
Aruba AP-85 Outdoor Access Point Series | Installation Guide
AP-85 Series Installation | 27
Figure 19 Positioning the AP-85 on a Horizontal Pole
arun_0131D
Connecting Required Cables
NOTE
Before connecting other cables, first connect the ground stud to ground reference. See Figure 20 for
the location of the ground stud.
RJ-45 CAT 5 Cable
To weatherproof and connect an RJ-45 terminated CAT 5E or better cable to an AP-85 (see Figure 20), perform the following
using the contents in the included kit that ships with your unit:
NOTE
The cable is not included and must be purchased separately. Purchase a suitable UV-resistant,
outdoor rated, CAT 5E or better RJ-45 cable for use with the AP-85.
1. Slide the cap over the terminated cable.
2. Slide the rubber grommet over the terminated cable.
3. Slide the connector shell over the terminated cable.
4. Slide the washer over the terminated cable.
5. Insert the rubber grommet into the top of the connector shell until the top surface of the grommet is flush with the top
edge of the connector shell.
6. Connect the terminated cable to the proper port: LAN/POE port on the AP-85TX model or the CONSOLE port on the AP85FX/LX models.
7. Screw the connector shell onto the interface on the AP-85.
8. Screw the cap onto the connector shell.
28 | AP-85 Series Installation
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Figure 20 Weatherproofing and Connecting an RJ-45 Terminated CAT 5 Cable
Cap
Rubber Grommet
Connector Shell
Washer
Terminated CAT 5E or Better Cable
Ground Stud
arun_0127
Aruba AP-85 Outdoor Access Point Series | Installation Guide
AP-85 Series Installation | 29
DC and AC Power Cables
To connect the power cables (wiring harnesses):
1. Screw the two-wire, 8-foot long DC power cable (wiring harness) to the DC interface on the AP-85TX, AP-85FX, or AP85LX model.
2. Screw the three-wire, 8-foot long AC power cable (wiring harness) to the AC interface on the AP-85FX or AP-85LX
models only.
Disconnect the AC mains before handling the AC power cable and connecting it to the AP-85.
WARNING
All connections made to the unit should conform to all local and national electrical codes. Power
cords with lengths longer than 15 ft and cords without plugs should only be installed in appropriate
areas. Check the codes for your area to ensure proper use.
NOTE
Figure 21 Connecting Power
DC Power Cable
AC Power Cable
Always shut power off to the unit to de-energize it before disconnecting any cables.
NOTE
Table 5 AC and DC Power Cable Descriptions
Cable Type
Wire Color
Assignment
DC Power Cable
Red
+12V
Black
Ground
30 | AP-85 Series Installation
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Table 5 AC and DC Power Cable Descriptions
Cable Type
Wire Color
Assignment
AC Power Cable: United States (US)
Black
Line
White
Neutral
Green
Ground
Brown
Line
Blue
Neutral
Green/Yellow
Ground
AC Power Cable: Europe (EU)
Fiber Optic Cable
To use the fiber optic termination kit that is shipped with the AP-85FX/LX models, follow the instructions in the included
Tyco document Instruction Sheet 408-10079.
NOTE
Fiber optic cables are not included and must be purchased separately. Purchase a suitable UVresistant, outdoor rated, multi-mode fiber optic cable for use with the AP-85FX and a single-mode
fiber optic cable for use with the AP-85LX.
Aruba provides a multi-language document containing country specific restrictions and additional safety and regulatory
information for all Aruba hardware products. This document can be viewed or downloaded from the following location:
www.arubanetworks.com/safety_addendum.
CLASS 1
LASER PRODUCT
Use of controls or adjustments of performance or procedures other than those specified in this
manual may result in hazardous radiation exposure.
CAUTION
This product complies with 21 CFR Chapter 1, Subchapter J, Part 1040.10, and IEC 60825-1: 1993, A1: 1997, A2: 2001, IEC
60825-2: 2000.
For continued compliance with the above laser safety standards, only approved Class 1 modules from our approved vendors
should be installed in Aruba products.
Lightning Arrestor Installation
Refer to the instructions that are shipped with the Aruba lightning arrestor (AP-LAR-1).
Antenna Installation
Refer to the instructions that are shipped with your Aruba outdoor rated antenna.
Aruba AP-85 Outdoor Access Point Series | Installation Guide
AP-85 Series Installation | 31
Verifying Post-Installation Connectivity
The LEDs on the AP-85 can be used after installation to verify that the AP is receiving power, that the AP is initializing
successfully, and that wireless connectivity is occurring (see "LED Status Indicators" on page 13). Refer to the ArubaOS
Quick Start Guide for further details on verifying post-installation network connectivity.
Configuring the AP-85
Configuration parameters are network or controller specific and are configured and stored on the Mobility Controller.
Network configuration settings are pushed out to the AP(s) but remain stored on the Mobility Controller. Configuration
settings can be configured via the ArubaOS Web UI, ArubaOS CLI, or Aruba MMS. Refer to their respective guides for further
details: the ArubaOS User Guide or Aruba Mobility Management System User Guide.
32 | AP-85 Series Installation
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Appendix A
Understanding Antennas
Aruba Antennas
Before you can select the antenna type needed for the deployment, read the basic wireless antenna information provided in
this section. This information will help you understand wireless antenna basics and Aruba antenna specifications.
Understanding Wireless Antennas
Omni-Directional vs. Directional Coverage
For optimal performance of your wireless network, it is essential to understand the purpose behind proper antenna
selection. Choosing the correct antenna type will ensure that RF energy is being directed to the correct coverage areas.
Omni-directional antennas provide equal coverage in all directions (see Figure 22), while directional antennas point RF
energy in a specific direction for RF concentration within a targeted area (see Figure 23).
Figure 22 Omni-Directional Antenna
Antenna Location
Area of Coverage
Direction of Coverage
Figure 23 Directional Antenna
Antenna Location
Area of Coverage
Direction of Coverage
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Understanding Antennas | 33
Antenna Beamwidth, Pattern, and Gain Considerations
Antenna gain is a relative measure of how the antenna compares to an ideal isotropic radiator. An ideal, isotropic radiator
would radiate power in all directions equally over a sphere. The relationship between gain, power, and propagation distance
is detailed already in textbooks and Wiki's, so these expressions are not repeated here. Antenna gain is often confused with
power gain in amplifiers, but it is important to note that antenna gain only makes a transmitter's power appear to be higher
than would be predicted by calculation of the power fed to the antenna and then spread equally over a sphere. Antenna gain
itself is a completely passive and bi-directional property, determined only by the shape and construction of the antenna.
Knowing that gain is only a comparison of the apparent power to the power that would be required if fed to an ideal isotropic
antenna, you realize that gain can only be created by distorting the antenna pattern from the ideal spherical pattern. Think of
this as focusing the same power that would normally distribute evenly over a sphere into a tighter region of space. Thus, the
higher the gain, the more concentrated (in some way) the antenna pattern must be in order to achieve that gain.
Example
To visualize the concept of gain, picture a rubber ball. The surface area of the ball represents the total available power
radiated by an ideal isotropic antenna over its sphere of radiation (see Figure 24).
Figure 24 Equal Signal Strength Radiated in All Directions
Equal Signal Strength
Radiated over a Sphere
34 | Understanding Antennas
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Now, still using the same ball with the same available surface area, how would you be able to stretch the ball farther out?
One way is to press down on the top of the ball and squash it down vertically. This would keep the same basic shape in the
horizontal plane (round), but it would force the ball to stretch, creating a pancake shape, in the vertical direction (see Figure
25). This represents the concept of the high gain omni-directional antenna, which achieves a greater coverage distance in the
horizontal direction at the expense of coverage in the vertical areas of the radiating sphere.
Figure 25 High Gain Omni-Directional Antenna
High Gain
Omni-Directional Antenna
Compressed vertical signal,
which expands signal
horizontally
To stretch the ball primarily in one direction (instead of in all directions), push the ball, both vertically and horizontally, on
the sides and on the back, to force the ball to deform in a single direction. This action would significantly distort the shape of
the original ball both horizontally and vertically, but it will allow you to stretch the same ball a lot farther in one direction
(see Figure 26). This represents the concept of the high gain directional antenna, which is designed to compress the entire
radiating sphere into a single predominate direction.
NOTE
Gain is created by forcing transmitted power to radiate in a preferred direction rather than radiating
in all directions of an ideal sphere. Therefore, a high gain signal is always accompanied by loss of
available signal in some other portion of the ideal sphere. High gain directional antennas are ideal for
sites requiring directed coverage in a specific area or extended range for bridging applications, but
they are not suited for sites requiring uniform coverage in large areas. It is important to keep in mind
that both vertical and horizontal coverage can be affected by the use of a higher gain antenna and
beamwidth (a measure of coverage) is always inversely related to gain.
Figure 26 High Gain Directional Antenna
High Gain Directional Antenna
Entire sphere compressed into a
single predominate direction, focusing
RF energy to a targeted area of
coverage
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Understanding Antennas | 35
Understanding Antenna Pattern Plots and Specifications
Traditional 2-D pattern plots and beamwidth specifications are like mental puzzles waiting to be solved because they only
provide a snapshot of the information in two planes. These two planes are often referred to as the azimuth (H-plane or
horizontal) and elevation (vertical or E-plane) planes. The azimuth view would be considered the view from directly above,
viewing the antenna pattern on the horizontal plane. The elevation view is considered to be a side view, viewing the antenna
pattern on the vertical plane. It is helpful to think of these planes as “cuts” of the real antenna pattern, which is actually 3-D.
Figure 27 illustrates where these “cuts” are located for a typical omni-directional antenna pattern.
Figure 27 Antenna Pattern Conventions (Omni-Directional Pattern Shown)
Elevation, E-plane,
or Vertical Pattern
Diagram
Azimuth, H-plane,
or Horizontal
Pattern Diagram
The antenna illustrated by Figure 27 is commonly referred to as the dipole pattern because it is the pattern produced by an
ideal dipole antenna. The gain of this antenna is 2.14, which is achieved by compression in the vertical plane (elevation)
compared to the ideal sphere. If referring to the true 3D pattern, this compression is sometimes called the donut shape (see
Figure 28).
Figure 28 Donut Shape Compression of an Omni-Directional Antenna
36 | Understanding Antennas
Aruba AP-85 Outdoor Access Point Series | Installation Guide
It is evident from Figure 27 that 2-D pattern plots typically provided in antenna specifications are a simplification of the real
3-D situation. Often, 2-D plots are reduced even further to a set of simple specifications based on the antenna gain and 3 dB
beamwidth.
Detachable Antenna Selection
Select the correct antenna type to support the required frequency band (2.4 GHz or 5 GHz) and desired coverage pattern.
To select the correct antenna type for the deployment, download and read Aruba’s outdoor antenna specifications: http://
www.arubanetworks.com/products/access-points/antennas.php.
NOTE
All figures are shown with a 100 meter (328 feet) mounting height above the ground and for a
18 Mbps coverage area.
Detachable Outdoor Antenna Types
These are some of the terms used to describe Aruba’s detachable antenna offerings. Terminology and degree of sector in
Aruba’s antenna specifications are determined by the horizontal 3 dB beamwidth.
Down-Tilt: An omni-directional antenna that focuses its energy downwards.
Sector/Patch: A directional antenna that provides a focused sector of coverage from a central point (Example: +/- 45
degrees from a 90 degree center point).
Panel: A flat formed antenna that directs energy to a sector of coverage. This type of antenna is often ideal for point-topoint WDS bridging or wireless mesh backhaul applications.
Detachable Antenna Selection Tips
If omni-directional coverage is desired with the greatest possible horizontal range from the AP, select one of Aruba's
detachable antennas with high-gain, omni-directional coverage. Due to the tight vertical beamwidth of high-gain, omnidirectional antennas, this typically requires mounting the antenna not more than 5 meters (16.5 feet) above the expected
client locations in elevation.
If omni-directional coverage is desired, but only high mounting locations are available
(approx. 5 m (16.5 feet) to 10 m (33 feet), consider the use of lower gain (3 dBi to 5 dBi) omni-directional antennas and a
denser AP deployment. The lower gain antenna will reduce the maximum horizontal range of the AP, but will provide
better vertical coverage.
For very high mounting locations (>10 m/33 feet) such as light poles or monopoles, consider the use of an omnidirectional antenna with electrical downtilt. A downtilt omni-directional antenna is an antennas that has a direction of
maximum gain at approximately 45° down from horizontal.
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Understanding Antennas | 37
Figure 29 AP-ANT-90 E-Plane View (Side View)
Figure 30 AP-ANT-90 H-Plane View (Top View)
Alternatively, for high mounting locations, high-gain sector antennas may be used with mechanical downtilt. This will
typically require the use of multiple access points per mounting location to provide omni-directional coverage.
If a directional antenna is required to direct RF coverage, the detachable antenna must be capable of supporting all of the
frequency bands that require support (2.4 GHz and/or 5 GHz).
Directional antennas are selected to focus RF energy more efficiently to a targeted area.
Directional antennas are also useful in areas where the surrounding materials have high amounts of RF attenuation or
reflection and the RF signal needs to be guided in the direction of the least amount of attenuation or reflection. For
38 | Understanding Antennas
Aruba AP-85 Outdoor Access Point Series | Installation Guide
example, when mounting antennas on the outside surfaces of a building to provide coverage to outdoor spaces in front of
the building, a directional antenna can be used to direct the coverage away from the building.
High Mounting Omni-Directional Antenna Scenario (AP-ANT-80 vs. AP-ANT-90)
The AP-ANT-80 shows greater horizontal range due to its higher gain (8 dBi vs. 3 dBi) antenna, but in this very high mounting
situation, the AP-ANT-90 may be a better choice for ground level coverage because the direction of maximum gain is
directed downward toward the ground. This situation could potentially be improved if a lower mounting elevation was
available for the AP-ANT-80, ideally about
5 m above Ground.
Figure 31 AP-ANT-80 E-Plane View (Side View)
Figure 32 AP-ANT-80 H-Plane View (Top View)
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Understanding Antennas | 39
High Mounting Directional Antenna Scenario
The AP-ANT-82 is a high gain (12 dBi), directional antenna with a 90 degree 3 dB beamwidth in azimuth. For this high
mounting condition, this antenna provides a long range in the direction of maximum gain, but it would require mechanical
downtilt for ground level coverage.
Figure 33 AP-ANT-82 E-Plane View (Side View)
Figure 34 AP-ANT-82 with 30 Degree Downtilt E-Plane View (Side View)
40 | Understanding Antennas
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Figure 35 AP-ANT-82 H-Plane View (Top View)
Figure 36 AP-ANT-82 with 30 Degree Downtilt H-Plane View (Top View)
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Understanding Antennas | 41
42 | Understanding Antennas
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Appendix B
Product Specifications
Product Specifications
Mechanical (AP-85TX, AP-85FX, and AP-85LX)
Device Dimensions (HxWxD):

10.80” x 12.64” x 3.07”

274 mm x 321 mm x 78 mm
Device Weight: 7.40 lbs/3.36 kgs
Device Weight with Mounting Plate: 9.65 lbs/4.38 kgs
Device Weight with Mounting Plate and Mounting Bracket: 10.85 lbs/4.92 kgs
IP68 (1 m depth for 8 hrs) under IEC 60529 NEMA type 4X
Temperature:

Operating: -30ºC to 55ºC (-22ºF to 131ºF)

Storage: -40ºC to 70ºC (-40ºF to 158ºF)
Relative Humidity: 0% to 95% non-condensing
Altitude: 0-3000 m (0-9850 ft)
Survival Wind Speed: 125 mph (201 km/hr)
Mounting:

Articulating adjustable pole or mast mount kit (included)

Antenna mount bracket (optional)
Antenna: Quad, N-type Female interfaces for external antenna support
Ground: Electrical safety/ground terminal point
Visual Status Indicators (LEDs):

Onboard LED array for RSSI level reading

PWR - Power/Status

LINK/ACT - LAN/Network Link Status

RADIO 0 - Radio 0 Status

RADIO 1 - Radio 1 Status

RSSI (Radio 0) - RSSI Level for Radio 0

RSSI (Radio 1) - RSSI Level for Radio 1
Electrical
AP-85TX
1 x 10/100 Base-T auto-sensing Ethernet (RJ-45) Interface

IEEE 802.3 BaseT and 802.3u 100BaseTX compliant

PoE 48V DC Power over Ethernet (IEEE 802.3af compliant)

Serial over Ethernet (SoE)
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Product Specifications | 43

Auto-sensing MDI/MDX
1 x 12 V DC / up to 2.0 A power interface (for external solar supplied DC power)
1 x Electrical Ground / Safety Terminal
Fully environmentally hardened connector types (all interfaces)
AP-85FX
1 x 100BASE-FX data uplink port for multi-mode, dual-fiber connectivity

1310 nm wavelength, 2 km over MMF Interface

1310 nm wavelength, 10km over SMF

LC fiber optic connector type
1 x 12 V DC up to 2.0 A power interface (for external solar supplied DC power)
1 x 90-228 V~ / 500 mA auto-sensing power interface with transient power surge suppression
1 x Serial Console Port
1 x Electrical Ground / Safety Terminal
Fully environmentally hardened connector types (all interfaces)
Maximum Power Draw
Table 6 AP-85 Series Maximum Power Draw
AP Model
Power Source
Measurement
Condition
Max Current
(Amps)
Max Power
(Watts)
AP-85TX
PoE
48 V
0.25
12
AP-85TX, AP-85FX, AP-85LX
DC
12 V
0.8
9.6
AP-85FX, AP-85LX
AC
240 V, 60 Hz
0.18 (RMS)
20.14
The 12 V DC input power source should be SELV (non-shock hazardous (<30 V DC) under normal and single fault
conditions) and limited power source (LPS) as a non-fire-hazardous circuit as defined in IEC 60950-1, or a Class Z power
source as defined by the NEC.
IT power system: Models AP-85FX and AP-85LX are designed for connection to TN or IT power distribution systems.
Wireless LAN
Network Standards - IEEE 802.11b, IEEE 802.11g and IEEE 802.11a
Antenna Type - None. Detachable, outdoor rated, 2.4 or 5 GHz antenna options available
Radio Technology:

802.11a/g - Orthogonal Frequency Division Multiplexing (OFDM)
44 | Product Specifications
Aruba AP-85 Outdoor Access Point Series | Installation Guide

802.11b - Direct Sequence Spread Spectrum (DSSS)
Radio Modulation Type:

802.11a - BPSK, QPSK,16-QAM, 64-QAM

802.11b - DQPSK/CCK, DQPSK, DBPSK

802.11g - OFDM, DQPSK/CCK, DQPSK, DBPSK
Media Access Control - CSMA/CA with ACK
Data Rates:

802.11a - 6, 9, 12, 18, 24, 36, 48 and 54 Mbps per channel

802.11b - 1, 2, 5.5, 11 Mbps per channel

802.11g - 1, 2, 5.5, 6, 9, 11, 12, 22, 24, 33, 36 and 54 Mbps per channel
Transmit and Available Channels: Determined by country of use and Aruba certifications within country of use
Safety and Regulatory Compliance
Aruba provides a multi-language document containing country specific restrictions and additional safety and regulatory
information for all Aruba hardware products. This document can be viewed or downloaded from the following location:
www.arubanetworks.com/safety_addendum.
CAUTION
Aruba Access Points and the AP-LAR-1 lightning arrestor are required to be installed by a
professional installer. The professional installer is responsible for ensuring that grounding is
available and it meets applicable local and national electrical codes.
Do not work on an AP and do not connect or disconnect cables during periods of lightning activity.
WARNING
Declaration of Conformity
Aruba Networks, Inc., 1322 Crossman Avenue, Sunnyvale, CA 94089, USA, declares that the Aruba Wireless Access Point,
Model: AP-85 conforms to the following European directives:
R&TTE Directive 99/5/EC
WEEE Directive 2002/96/EC
RoHS Directive 2002/95/EC
ATEX Directive 94/9/EC
R&TTE Directive relevant standards:
Article 3.2; EN 300 328v1.7.1 and, EN 301 893 v1.4.1
Article 3.1b; EN 301 489-17 v1.2.1
Article 3.1a; EN 60950-1, EN60950-22
ATEX Directive standard:
EN60079-0:2004, EN60079-15:2005
Year Mark first applied: 2008
I, the undersigned, hereby declare that the equipment specified above conforms to the above Directives and Standards.
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Product Specifications | 45
European Headquarters
77 Oxford Street
London, W1D 2ES
United Kingdom
Phone: +44 20 7659 2024
Fax: +44 20 7043 5871
Contact: Albert Benhamou
info-emea@arubanetworks.com
Instructions for Use in a Potentially Explosive Atmosphere
ARUBA NETWORKS, INC.
1344 Crossman Ave. Sunnyvale, CA 95014, U.S.A.
12V
; 2A or 48V
; 350mA
IP67 TYPE 4X Manufactured: 2008
MODEL: AP-85TX
FCC ID: Q9DAP85
IC: 4675A-AP85
N19592
ARU-AP85TX
ARUBA NETWORKS, INC.
MODEL: AP-85TX
1344 Crossman Ave. Sunnyvale, CA 94089, U.S.A.
II 3 G Ex nA T6
-30°C < Tamb < 55°C
TUVNA 08 ATEX 7155 X
WARNING – DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE MAY BE PRESENT.
WARNING – POTENTIAL ELECTROSTATIC CHARGING HAZARD – SEE INSTRUCTIONS FOR ANTENNA DETAILS.
WARNING – DO NOT ENERGIZE OR DE-ENERGIZE UNIT AT THE UNIT’S POWER CONNECTORS WHEN AN
EXPLOSIVE ATMOSPHERE MAY BE PRESENT.
Type of Protection:
II 3 G Ex nA T6 ; ignition protection category “n”
Enclosure:
NEMA Type 4X, IP67
Applicable Standards:
IEC 60079-0:2004
EN 60079-0:2004
IEC 60079-15:2005
EN 60079-15:2005
46 | Product Specifications
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Do not open the unit when an explosive atmosphere may be present.
WARNING
Do not energize or de-energize the unit at the unit’s power connectors when an explosive
atmosphere may be present.
Potential Electrostatic Charging Hazard.
WARNING
The antennas installed with the Model AP-85TX should be mounted in a location where they are not
subjected to winds, in order to minimize the build up a charge and potential arcing on the antennas.
CAUTION
CAUTION
CAUTION
CAUTION
During all servicing and maintenance activities, the antennas must be handled with extreme caution
to minimize possible electrostatic static discharge (ESD) and arcing events. Any cleaning means, in
particular, should minimize such events on the plastic surfaces of the antennas, which may contain
or produce a charge potential.
Only the Model AP-85TX itself is intended to be used in a potentially explosive environment. The
external power adapter, PoE power injector, and power sourcing equipment (PSE, that is,
controllers) are intended to be installed only in a safe environment and are not intended for
installation in a potentially explosive environment.
The Model AP-85TX is intended to be powered only by the external power adapter or power injector
provided with the unit, or by power sourcing equipment (PSE) that is compliant with IEEE802.3af.
The product must be powered only by energy-limited circuits, which satisfy the requirements of
EN 60079-15. The explosion group is dependent upon the use of an energy-limited supply circuit.
Proper Disposal of Aruba Equipment
For the most current information on Global Environmental Compliance and Aruba products please see our website at
www.arubanetworks.com.
Waste of Electrical and Electronic Equipment
Aruba products at end of life are subject to separate collection and treatment in the EU Member States,
Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out
wheelie bin). The treatment applied at end of life of these products in these countries shall comply with
the applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and
Electronic Equipment (WEEE).
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Product Specifications | 47
European Union RoHS
Aruba products comply with the EU Restriction of Hazardous Substances Directive 2002/95/EC
(RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical
and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead
(including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba
products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies).
Products and packaging will be marked with the “RoHS” label shown at the left indicating conformance to this Directive.
China RoHS
Aruba products comply with China environmental declaration requirements and are labeled with the “EFUP e”
label shown at the left.
48 | Product Specifications
Aruba AP-85 Outdoor Access Point Series | Installation Guide
Index
AC power................................................................... 12
AC power cable......................................................... 30
access point setup .................................................... 21
AP-85TX
10/100Base-T ports............................................ 10
interfaces ............................................................ 10
LAN..................................................................... 10
PoE ..................................................................... 10
SPoE ................................................................... 10
accessories ............................................................... 14
antenna...................................................................... 33
beamwidth .......................................................... 34
detachable selection........................................... 37
directional ........................................................... 33
gain ..................................................................... 34
height .................................................................. 17
installation ........................................................... 31
interfaces ............................................................ 10
omni-directional .................................................. 33
orientation ........................................................... 18
pattern................................................................. 34
pattern plots........................................................ 36
position ............................................................... 18
specifications ...................................................... 36
understanding of................................................. 33
wireless ............................................................... 33
AP-85 Series
about..................................................................... 7
antenna interfaces .............................................. 10
bottom view
AP-85 TX model ........................................... 10
cable connection ................................................ 28
configuration ....................................................... 32
front view .............................................................. 9
installation ........................................................... 22
LEDs.................................................................... 13
overview................................................................ 9
package checklist ................................................. 8
power cable connection ..................................... 30
rear view................................................................ 9
RJ-45 cable connection...................................... 28
software requirements .......................................... 8
specifications ...................................................... 43
top view .............................................................. 10
beamwidth ................................................................ 34
cables........................................................................ 28
cabling........................................................... 19, 28, 30
configuration ............................................................. 32
connecting cables ............................................... 28, 30
connectivity ......................................................... 22, 32
console port .............................................................. 11
customer support........................................................ 6
DC power ............................................................ 10, 11
DC power cable ........................................................ 30
deployment ............................................................... 15
detachable antennas................................................. 37
directional antenna.................................................... 33
environment .............................................................. 19
ethernet cabling ........................................................ 19
fiber interface ............................................................ 11
AP-85FX
100Base-FX ........................................................ 11
console port ........................................................ 11
multi-mode fiber.................................................. 11
AP-85LX
100Base-LX ........................................................ 11
console port ........................................................ 11
single-mode fiber ................................................ 11
grounding point................................................... 11, 12
Aruba AP-85 Outdoor Access Point Series | Installation Guide
gain ........................................................................... 34
grounding .................................................................. 19
| 49
I
installation ..................................................... 21, 22, 23
configuration ....................................................... 32
pole mounting (>3.5" Diameter) .......................... 26
pole mounting (1.5" to 3.5" Diameter) ................ 24
positioning .......................................................... 27
post-installation connectivity .............................. 32
preparation.......................................................... 23
wall mounting...................................................... 23
LC connector............................................................. 11
LEDs .......................................................................... 13
lightning arrestor ................................................. 10, 31
line of sight ................................................................ 16
power over ethernet .................................................. 10
pre-installation .......................................................... 23
checklist.............................................................. 21
connectivity ........................................................ 22
network setup..................................................... 21
provisioning ........................................................ 22
provisioning............................................................... 22
radio interference ...................................................... 19
radio path planning ................................................... 16
regulatory compliance............................................... 45
RF absorbers............................................................. 15
RF interference sources ............................................ 16
RF reflectors.............................................................. 15
RJ-45 cable............................................................... 28
mounting ................................................................... 23
RSSI LEDs................................................................. 13
multi-mode fiber interface ......................................... 11
RSSI levels ................................................................ 14
network setup............................................................ 21
safety......................................................................... 45
N-type antenna interfaces ......................................... 10
scale requirements.................................................... 15
serial console port..................................................... 11
serial power over ethernet ........................................ 10
omni-directional antenna........................................... 33
single-mode fiber interface ....................................... 11
operation
modes of ............................................................... 7
software requirements ................................................ 8
outdoor conditions .................................................... 19
outdoor deployment .................................................. 15
outdoor planning ....................................................... 15
specifications ............................................................ 43
SPoE ......................................................................... 10
status indicators........................................................ 13
support, customer....................................................... 6
overview ...................................................................... 9
package checklist........................................................ 8
planning..................................................................... 15
wall mounting............................................................ 23
weather ..................................................................... 19
wireless antenna ....................................................... 33
PoE ............................................................................ 10
pole mounting (1.5" to 3.5" Diameter)....................... 24
pole moutning (>3.5" Diameter) ................................ 26
positioning ................................................................. 27
post-installation......................................................... 32
power
AC ....................................................................... 12
DC ................................................................. 10, 11
power cables ............................................................. 30
50 |
Aruba AP-85 Outdoor Access Point Series | Installation Guide

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : rsmall
Create Date                     : 2008:11:24 13:46:39Z
Modify Date                     : 2008:11:24 16:40:53-08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Creator Tool                    : FrameMaker 8.0
Metadata Date                   : 2008:11:24 16:40:53-08:00
Format                          : application/pdf
Title                           : AP-85IG_0510323-06.book
Creator                         : rsmall
Document ID                     : uuid:d94d5a65-b30b-4420-afd2-edf2f4a22e15
Instance ID                     : uuid:55a5e52f-42ed-4ad4-904c-6de5643bdb72
Page Mode                       : UseOutlines
Page Count                      : 50

EXIF Metadata provided by EXIF.tools

Aruba Networks AP85FXLX Aruba AP-85FX and AP-85LX Access Points User Manual AP 85IG 0510323 06

Aruba Networks, Inc. Aruba AP-85FX and AP-85LX Access Points AP 85IG 0510323 06

Users Manual

FCC ID Filing: Q9DAP85FXLX

Navigation menu

Namespaces

Views

Navigation