Aruba Networks APIN0314315 Aruba 310 Series Wireless Access Point User Manual 0511871 01 AP 31x IG

Aruba Networks, Inc. Aruba 310 Series Wireless Access Point 0511871 01 AP 31x IG

Contents

User Manual pt 1

Aruba 310 Series Wireless Access PointInstallation GuideThe Aruba 310 Series Wireless Access Points support IEEE 802.11ac standards for a high-performance WLAN. This device is equipped with two single-band radios, which provide network access and monitor the network simultaneously. This access point to deliver high-performance 802.11n 2.4GHz and 802.11ac 5GHz functionality, while also supporting 802.11a/b/g wireless services. Multi-user Multiple-in, Multiple-output (MU-MIMO) is enabled when operating in 5GHz mode for optimal performance.The AP-314 and AP-315 access points work in conjunction with an Aruba controller, while IAP-314 and IAP-315 access points can be configured via built-in virtual controller.310 Series wireless access points provides the following capabilities:IEEE 802.11a/b/g/n/ac wireless access pointIEEE 802.11a/b/g/n/ac wireless air monitorIEEE 802.11a/b/g/n/ac spectrum monitorCompatible with IEEE 802.3at and 802.3af PoESupport for MCS8 and MCS9Centralized management, configuration and upgradesIntegrated Bluetooth Low Energy (BLE) radioPackage Contents(I)AP-314 or (I)AP-315 access point 9/16" and 15/16” Ceiling Rail AdaptersSafety, Compliance, and Warranty Information guideAruba Instant Quick Start Guide (IAP-314 and IAP-315 only)Aruba Professional Installation Guide (IAP-314 only)Aruba 310 Series Wireless Access Point Installation Guide (this document)SoftwareAP-314 and AP-315 access points require ArubaOS 6.5.0 or higher. For additional information, refer to the ArubaOS User Guide and ArubaOS Quick Start Guide. 310 Series Hardware OverviewFigure 1 LED Status IndicatorsLEDsThe 310 Series has two LEDs that indicate the system and radio status. The LEDs have three operating modes that can be selected in the system management software:Default mode: see Table 1Off mode: LEDs are offBlink mode: LEDs blink green Table 1: 310 Series LED Status IndicatorsExternal Antenna ConnectorsThe (I)AP-314 access points are equipped with four external antenna connectors located on the front corners of the access point (see Figure 2).Figure 2 External Antenna Connectors Antennas ports ANT0 and ANT1 have dual band functionality and support both 2.4GHz and 5GHz, while ANT2 and ANT3 are single-band and support 5GHz only.USB InterfaceThe 310 Series is equipped with a USB port for connectivity with cellular modems and other USB client devices. Figure 3 USB PortWhen powered by an 802.3at or DC source, the USB port can supply power up to 5W.The USB interface is disabled when the access point is powered by an 802.3af PoE source.Figure 4 Back Panel Console PortThe console port allows the user to connect the access point directly to a serial terminal or laptop for local management. Connect the device to a terminal or terminal server using an Ethernet cable.The port is a 4-pin HDR connector with pin-out details in Figure 5.Figure 5 Serial Port Pin-OutEthernet PortsThe 310 Series is equipped with a 100/1000Base-T auto-sensing MDI/MDX Ethernet port. This port supports wired-network connectivity, in addition to Power over Ethernet (PoE) from IEEE 802.3af and 802.3at compliant power sources. This device accepts 56V DC (802.3at), or 48V DC (802.3af) nominal as a standard powered device (PD) from power sourcing equipment, including PoE midspan injector or a PoE-sourcing network infrastructure.The port is an RJ45 connector, marked on the enclosure with ”57V 600mA.”Figure 6 RJ45 Gigabit Port Pin-OutKensington Lock SlotThe 310 Series is equipped with a Kensington lock slot for additional security, shown in Figure 4. Reset ButtonThe reset button can be used to return the access point to factory default settings. To reset the access point, refer to the steps below:1. Power off the access point.2. Press and hold the reset button using a small, narrow object, such as a paperclip.3. Power-on the access point without releasing the reset button. The power LED will flash within 5 seconds.4. Release the reset button.The power LED will flash again within 15 seconds indicating that the reset is completed. The access point will now continue to boot with the factory default settings.PowerThe Ethernet port supports PoE-in and may draw power from an 802.3at (recommended) or an 802.3af source. If PoE is unavailable, the 310 Series access points have a single 12V/36W DC power input to support the AP-AC-V30B AC-to-DC power adapter kit (sold separately).When both 802.3at and DC power sources are available, the DC power source will take precedence. The Access point will simultaneously draw a minimal current from the PoE source. In the event that the DC source fails, the access point will switch to the 802.3at source.The 310 Series operates without restriction when powered by 802.3at compliant and DC power sources. In this mode the USB interface is enabled and supports up to 1A/5W to a powered device (PD). When powered by an 802.3af PoE source, the access point operates in power-saving mode. In this mode the USB interface is disabled.Table 2: Power ModesBefore You BeginAccess Point Pre-Installation ChecklistBefore installing your 310 Series access point, ensure that you have the following:CAT5E UTP cable or betterOne of the following power sources:IEEE 802.3at or 802.3af-compliant Power over Ethernet (PoE) source. The PoE source can be any power source equipment (PSE) controller or midspan PSE deviceAruba AP-AC-12V30UN adapter kit (sold separately)For AP-314 and AP-315 access points only:Aruba controller provisioned on the network:Layer 2/3 network connectivity to your access pointOne of the following network services:Aruba Discovery Protocol (ADP)Inform your supplier if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed.Aruba access points are classified as radio transmission devices, and are subject to government regulations of the host country. The network administrator(s) is/are responsible for ensuring that configuration and operation of this equipment meet all regulatory standards of their country/domain. For complete list of country-approved channels and devices, refer to the Aruba Downloadable Regulatory Table at www.arubanetworks.com.LED Color/State MeaningSystem Status(Left)Off Device powered offGreen- blinking Device booting, not ready for useGreen- solid Device ready for useAmber- solid Device ready; Power Save mode (802.3af PoE)Amber- blinking Device operating in restricted mode. Meets one of the following conditions:Uplink negotiated in sub-optimal speed (<1Gbps), orEthernet radio is in non High-Throughput (HT) modeGreen/Amber- solid No software setting/network restrictionsRed System error conditionRadio Status(Right)Off Device powered off; or both radios disabledGreen- solid Both radios enabled in access modeGreen- blinking One radio enabled in access mode; other disabledAmber- solid Both radios enabled in monitor modeAmber- blinking One radio enabled in monitor mode; one radio disabledAlternating Green: one radio in access modeAmber: one radio in monitor modeExternal antennas for this device must be installed by an Aruba Certified Mobility Professional (ACMP) or other Aruba-certified technician, using manufacturer-approved antennas only. The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the regulatory limit set by the host country/domain. Installers are required to record the antenna gain for this device in the system management software.ANT1 ANT0ANT2 ANT3USB PortEthernet PortConsole PortKensington LockDC Power SocketReset Button1 3.3V2 RX3 TX4 GNDPin Signal1000Base-T Gigabit Ethernet PortRJ-45 FemalePin-OutSignal Name12345678BI_DC+BI_DC-BI_DD+BI_DD-BI_DA+BI_DA-BI_DB+BI_DB-FunctionBi-directional pair +CBi-directional pair -CBi-directional pair +DBi-directional pair -DBi-directional pair +ABi-directional pair -ABi-directional pair +BBi-directional pair -B Power Source Limitations USB OutputDC (AP-AC-12V30B) No restrictions 1A/5WPoE 802.3at No restrictions 1A/5WPoE 802.3af USB disabled DisabledFCC Statement: Improper termination of access points installed in the United States configured to non-US model controllers is a violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80).EU Statement: Lower power radio LAN product operating in 2.4 GHz and 5 GHz bands. Please refer to the ArubaOS User Guide/Aruba Instant User Guide for details on restrictions.Produit réseau local radio basse puissance operant dans la bande fréquence 2.4 GHz et 5 GHz. Merci de vous referrer au ArubaOS User Guide/Aruba Instant User Guide pour les details des restrictions.Low Power FunkLAN Produkt, das im 2.4 GHz und im 5 GHz Band arbeitet. Weitere Informationen bezlüglich Einschränkungen finden Sie im ArubaOS User Guide/Aruba Instant User Guide.Apparati Radio LAN a bassa Potenza, operanti a 2.4 GHz e 5 GHz. Fare riferimento alla ArubaOS User Guide/Aruba Instant User Guide per avere informazioni detagliate sulle restrizioni.
Aruba 310 Series Wireless Access PointInstallation Guidea Hewlett PackardEnterprise companywww.arubanetworks.com1344 Crossman AvenueSunnyvale, California 94089Phone: 408.227.4500Fax 408.227.4550Aruba 310 Series Wireless Access Point | Installation GuidePart Number 0511871-02 | January 2016a Hewlett PackardEnterprise companyContacting Aruba NetworksWeb SupportMain Site http://www.arubanetworks.com Support Site https://support.arubanetworks.com Airheads Social Forums and Knowledge Base http://www.community.arubanetworks.comNorth American Telephone 1-800-943-4526 (Toll Free)1-408-754-1200International Telephones http://www.arubanetworks.com/support-services/aruba-support-program/contact-support/Software Licensing Site http://licensing.arubanetworks.comEnd-of-life Information http://www.arubanetworks.com/support-services/end-of-life/Security Incident Response Team (SIRT) http://www.arubanetworks.com/support-services/security-bulletins/Support Email AddressesAmericas, EMEA and APAC support@arubanetworks.comSecurity Incident Response Team (SIRT) Email sirt@arubanetworks.comCopyright© Copyright 2016 Hewlett Packard Enterprise Development LPOpen Source CodeCertain Aruba products include Open Source software code developed by third parties, including software code subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other Open Source Licenses. The Open Source code used can be found at this site:http://www.arubanetworks.com/open_sourceWarrantyThis hardware product is protected by an Aruba warranty. For details, see the Safety, Compliance, and Warranty Information Guide included with this device.DNS server with an “A” recordDHCP Server with vendor-specific options.Verifying Pre-Installation Connectivity Before installing access points in a network environment, make sure that they are able to locate and connect to the controller after power on.Specifically, you must verify the following conditions:When connected to the network, each access point is assigned a valid IP addressAccess points are able to locate the controller Refer to the ArubaOS Quick Start Guide for instructions on locating and connecting to the controller.Pre-Installation Network RequirementsAfter WLAN planning is complete and the appropriate products and their placement have been determined, the Aruba controller(s) must be installed and initial setup performed before the Aruba access points are deployed.For initial setup of the controller, refer to the ArubaOS Quick Start Guide for the software version installed on your controller.Identifying Specific Installation LocationsYou can mount the 310 Series access point to a wall or on the ceiling. Use the access point placement map generated by Aruba’s RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/interference sources will impact RF propagation and should have been accounted for during the planning phase and adjusted for in RF plan.Identifying Known RF Absorbers/Reflectors/Interference SourcesIdentifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach an access point to its fixed location. Examples of sources that degrade RF performance include:Cement and brickObjects that contain waterMetalMicrowave ovensWireless phones and headsetsInstalling the Access PointRefer to the following steps to install your Aruba 310 Series access point using the AP Ceiling Rail Mount Kit (AP-220-MNT-C1).Using the Ceiling Rail AdapterThe 310 Series access point ships with two ceiling rail adapters for 9/16” and 15/16” ceiling rails. Additional wall mount adapters and ceiling rail adapters for other rail styles are available as accessory kits.1. Pull the necessary cables through a prepared hole in the ceiling tile near where the access point will be placed.2. Place the adapter against the back of the access point with the adapter at an angle of approximately 30 degrees to the tabs (see Figure 7).3. Twist the adapter clockwise until it snaps into place in the tabs (see Figure 7).Figure 7 Attaching the Ceiling Rail Adapter4. If necessary, connect the console cable to the console port on the back of the access point.5. Hold the access point next to the ceiling tile rail with the ceiling tile rail mounting slots at approximately a 30-degree angle to the ceiling tile rail (see Figure 8). Make sure that any cable slack is above the ceiling tile.6. Pushing toward the ceiling tile, rotate the access point clockwise until the device clicks into place on the ceiling tile rail.Figure 8 Mounting the Access Point7. On the (I)AP-314, install the external antennas according to the manufacturer’s instructions, and connect the antennas to the antenna interfaces on the access point.Connecting Required CablesInstall cables in accordance with all applicable local and national regulations and practices.Verifying Post-Installation ConnectivityThe integrated LEDs on the access point can be used to verify that the device is receiving power and initializing successfully (see Table 1). Refer to the ArubaOS Quick Start Guide for further details on verifying post-installation network connectivity.Configuring the 310 Series The instructions for the following section are applicable to AP-314 and AP-315 model access points only.Access Point Provisioning/ReprovisioningProvisioning parameters are unique to each access point. These local access point parameters are initially configured on the controller which are then pushed out to the access points and stored on the devices. Aruba recommends that provisioning settings be configured via the ArubaOS Web UI only. Refer to the ArubaOS User Guide for complete details.Access Point ConfigurationConfiguration parameters are network or controller specific and are configured and stored on the controller. Network configuration settings are pushed out to the access points, but remain stored on the controller.Configuration settings can be configured via the ArubaOS Web UI or ArubaOS CLI. Refer to their respective guides for further details: the ArubaOS User Guide.Aruba Networks, Inc., in compliance with governmental requirements, has designed the 310 Series access points so that only authorized network administrators can change the settings. For more information about access point configuration, refer to the ArubaOS Quick Start Guide/Aruba Instant Quick Start Guide and ArubaOS User Guide/Aruba Instant User Guide.The instructions for this section are applicable to the AP-314 and AP-315 only.This device must be professionally installed and serviced by an ACMP or other Aruba-certified technician. The installer is responsible for securing the access point onto the ceiling tile rail in accordance with the steps below. Failure to properly install this product may result in physical injury and/or damage to property.

Navigation menu