Aruba Networks APIN0324325 Wireless Access Point User Manual

Aruba Networks, Inc. Wireless Access Point

Contents

Regulatory and safety Manual

Aruba 320 Series Wireless Access Point Regulatory Compliance and Safety Information Guide0511817-04 | July 2015 1IntroductionThis document contains domestic and international regulatory compliance and safety information for 320 Series access points. To ensure that this device complies with the regulatory standards for your region, please refer to the sections below.Electrical and Environmental SpecificationsRegulatory InformationProper Disposal of Aruba EquipmentElectrical and Environmental SpecificationsFor additional specifications on this product, please refer to the product data sheet at www.arubanetworks.com/safety_addendum.ElectricalEthernet:2x 10/100/1000 Base-T auto-sensing Ethernet RJ-45 interface (E0-E1)Maximum power consumption (excluding USB): 20W (PoE) or 18.5W (DC)IEEE 802.3 (10 Base-T), IEEE 802.3u (100 Base-T). IEEE 802.3ab (1000 Base-T)Power over Ethernet (IEEE 802.3at or 802.3af complaint), 48VDC or 53VDC (nominal) and 57VDC/350mA (maximum).Power:12VDC power interference, support powering through an AC-to-DC power adapter (AP-AC-12V30UN)Maximum power consumption (excluding USB):20W (PoE) or 18.5W (DC)EnvironmentalOperating:Temperature: 0°C to +50°C (+32°F to +122°F)Humidity: 5% to 95% non-condensingStorage and transport:Temperature: -40°C to +70°C (40°F to +158°F)!All Aruba access points should be professionally installed by an Aruba Certified Mobility Professional (ACMP). The installer is responsible for ensuring that grounding is available and meets applicable national and electrical codes.!Tous les points d'accès Aruba doivent impérativement être installés par un professionnel agréé. Ce dernier doit s'assurer que l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques nationaux en vigueur.If a power adapter other than the Aruba-approved adapter is used in the US or Canada, it should be NRTL listed, without an output rated 12VDC, minimum 2A, marked “LPS” and “Class 2”, and suitable for plugging into a standard power receptacle in the US and Canada.
2 Aruba 320 Series Wireless Access Point | Regulatory Compliance and Safety Information GuideRegulatory InformationAruba Networks provides a multi-language document that contains country-specific restrictions and additional safety and regulatory information for all Aruba access points. This document can be viewed or downloaded at www.arubanetworks.com.FCCFCC Class B Part 15This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 ofthe FCC Rules. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the manufacturer’s instructions, may cause interference harmful to radio communications.Operation is subject to the following conditions:This device may not cause harmful interference.This device must accept any interference received, including interference that may cause undesired operation.If this equipment does cause interference, which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio or TV technician for help.Complies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standardentitled “Digital Apparatus,” ICES-003 of Industry Canada.Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and 5650-5850MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN devices.CanadaComplies with the Class B limits for radio noise emissions as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (E.I.R.P.) does not exceed the limit necessary for successful communication.This device complies with Industry Canada license-exempt RSS standard(s).Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. !RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 10.63 inches (27cm) between the radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. When operated in 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems.!Déclaration sur les limites d'exposition aux radiofréquences : cet équipement est conforme aux limites d'exposition aux rayonnements radioélectriques spécifiées par la FCC. Il doit être installé et utilisé à une distance minimale de 27 cm par rapport à votre corps pour les fréquences de 2,4 et 5 GHz. Cet émetteur-récepteur ne doit pas être utilisé ou situé à proximité d'autres antennes ou émetteurs-récepteurs. En cas d'utilisation dans la plage de fréquences de 5,15 à 5,25 GHz, cet appareil doit uniquement être utilisé en intérieur afin de réduire les risques d'interférence avec les systèmes satellites mobiles partageant le même canal.!Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.!Toute modification effectuée sur cet équipement sans l'autorisation expresse de la partie responsable de la conformité est susceptible d'annuler son droit d'utilisation.
Aruba 320 Series Wireless Access Point | Regulatory Compliance and Safety Information Guide 3Déclaration d’Industrie CanadaCet appareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada.Conformément aux réglementations d’Industrie Canada, cet émetteur-récepteur radio doit être utilisé uniquement avec une antenne dont le type et le gain maximal doivent être approuvés par Industrie Canada. Pour réduire les interférences radio potentielles, le type d’antenne et son gain doivent être choisis de façon à ce que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas les valeurs nécessaires à une communication efficace. Ce périphérique est conforme aux règlements RSS exempts de licence d’Industrie Canada. L’utilisation de ce périphérique est soumise aux deux conditions suivantes : (1) ce périphérique ne doit pas provoquer d’interférences, et (2) ce périphérique doit accepter toute interférence, y compris les interférences susceptibles de provoquer un dysfonctionnement.EU Regulatory Conformance Aruba Networks Inc., hereby declares that the 320 Series Wireless Access Points are in compliance with directives listed below:EMC Directive 2004Low Voltage Directive 2006R&TTE Directive 1999REACH Regulation (EC) No.: 1907/2006RoHS Directive 2011WEEE Directive 2002A Declaration of Conformity for these directives is available for viewing at www.arubanetworks.com.Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz and 5650-5850MHz and these Radars could cause interference and/or damage to Licensed Exempt WLAN devices.Medical1. Equipment not suitable for use in the presence of flammable mixtures.2. Connect to only IEC 60950-1 or IEC 60601-1 3rd edition certified products and power sources. The end user is responsible for the resulting medical system complies with the requirements of IEC 60601-1 3rd edition.3. Wipe with a dry cloth, no additional maintenance required.4. No serviceable parts, the unit must be sent back to the manufacturer for repair.5. No modifications are allowed without Aruba approval.䫔⋩Ḵ㡅ˢˢ䴻✳⺷娵嫱⎰㟤ᷳỶ≇䌯⮬柣暣㨇炻朆䴻姙⎗炻℔⎠ˣ⓮嘇ㆾἧ䓐侭⛯ᶵ⼿㑭冒嬲㚜柣䌯ˣ≈⣏≇䌯ㆾ嬲㚜⍇姕妰ᷳ䈡⿏⍲≇傥ˤ䫔⋩⚃㡅ˢˢỶ≇䌯⮬柣暣㨇ᷳἧ䓐ᶵ⼿⼙枧梃凒⬱ℐ⍲⸚㒦⎰㱽忂ᾉ烊䴻䘤䎦㚱⸚㒦䎦尉㗪炻ㅱ䩳⌛ 䓐炻᷎㓡┬军䃉⸚㒦㗪㕡⼿两临ἧ䓐ˤˢˢ⇵枭⎰㱽忂ᾉ炻㊯ὅ暣ᾉ㱽夷⭂ἄ㤕ᷳ䃉䶂暣忂ᾉˤˢˢỶ≇䌯⮬柣暣㨇枰⽵⍿⎰㱽忂ᾉㆾⶍ㤕ˣ䥹⬠⍲慓䗪䓐暣㲊廣⮬⿏暣ġġġġ㨇姕⁁ᷳ⸚㒦ˤProper Disposal of Aruba EquipmentDispose of Aruba products per local regulation. For the most current information about Global Environmental Compliance and Aruba products, see our website at www.arubanetworks.com.Expected Service Life 10 years. For additional compliance information, refer to the label on the side of this device.
© 2015 Aruba Network, Inc. Airwave®, Aruba Networks®, Aruba Mobility Management System®, Bluescanner, For Wireless That Works®, Mobile Edge Architecture, People Move. Networks Must Follow., RFProtect®, The All Wireless Workplace Is Now Open For Business, and The Mobile Edge Company® are trademarks of Aruba Networks, Inc. All rights reserved. All other trademarks are the property of their respective owners.www.arubanetworks.com1344 Crossman AvenueSunnyvale, California 94089Phone: 408.227.4500Fax: 408.227.45504 Aruba 320 Series Wireless Access Point | Regulatory Compliance and Safety Information GuideWaste of Electrical and Electronic EquipmentAruba products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2002/96EC on Waste of Electrical and Electronic Equipment (WEEE).India RoHSThis product complies with RoHS requirements as prescribed by E-Waste (Management & Handling) Rules, governed by the Ministry of Environment & Forests, Government of India.European Union RoHSAruba products also comply with the EU Restriction of Hazardous Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the “RoHS” label shown at the left indicating conformance to this directive.China RoHSAruba products also comply with China environmental declaration requirements and are labeled with the “EFUP 10” label shown at the left.10᳝↦᳝ᆇ⠽䋼ໄᯢHazardous Materials Declaration᳝↦᳝ᆇ⠽䋼៪ܗ㋴(Hazardous Substance) 䚼ӊৡ⿄(Parts) 䪙3E∲+J䬝&G݁Ӌ䫀&U໮⒈㘨㣃3%%໮⒈Ѡ㣃䝮3%'(⬉䏃ᵓ(PCA Boards)hƻ ƻ ƻ ƻ ƻᴎẄ㒘ӊ(Mechanical Sub-Assemblies)hƻ ƻ ƻ ƻ ƻƻ˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼SJ/T11363-2006ᷛޚ㾘ᅮⱘ䰤䞣㽕∖ҹϟDŽIndicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard.h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎ6-7ᷛޚ㾘ᅮⱘ䰤䞣㽕∖DŽIndicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. ᇍ䫔ଂП᮹ⱘ᠔ଂѻકᴀ㸼ᰒ⼎կᑨ䫒ⱘ⬉ᄤֵᙃѻકৃ㛑ࣙ৿䖭ѯ⠽䋼DŽThis table shows where these substances may be found in the supply chain of electronic information products, as of the date of sale of the enclosed product. ℸᷛᖫЎ䩜ᇍ᠔⍝ঞѻકⱘ⦃ֱՓ⫼ᳳᷛᖫᶤѯ䳊䚼ӊӮ᳝ϔϾϡৠⱘ⦃ֱՓ⫼ᳳ՟བ⬉∴ऩܗ῵ഫ䌈೼݊ѻકϞℸ⦃ֱՓ⫼ᳳ䰤া䗖⫼Ѣѻકᰃ೼ѻક᠟ݠЁ᠔㾘ᅮⱘᴵӊϟᎹ԰The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here. The Environment- Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual.

Navigation menu