Ascion RC-WM-E02 Transmitter of Remote Control User Manual Serta MSI Manual 1118 13 P01 NEW

Ascion, LLC Transmitter of Remote Control Serta MSI Manual 1118 13 P01 NEW

User manual

Owner’s Manual Manual Part No. D1103-Serta-MSI REV: 2013-11-26Copyright © 2013 . All Rights Reserved Ascion LLC.
Warranty Information: Please see the warranty that came with your product.Serta Motion SIGNATURE Adjustable Foundation 2Remote Control Operation Guide..........................................................................................16Replacement Remote Control Programming....................................................................18Emergency Power Down Feature...........................................................................................19Remote Stand User’s Guide......................................................................................................20Troubleshooting...........................................................................................................................21Warranty.......................................................................................................................................... 22CUSTOMER SERVICE: 800-695-2540Table Of Contents Safety Precautions........................................................................................................................3Parts List...........................................................................................................................................8Frame Assembly Instructions...................................................................................................9Bluetooth Accessory Module User’s Guide.........................................................................12Wireless Remote Control...........................................................................................................15
CUSTOMER SERVICE: 800-695-25403WARNING! IMPORTANT SAFETY INSTRUCTIONS.PLEASE READ THESE INSTRUCTIONSTHOROUGHLY BEFORE USING THIS PRODUCT.SAVE THESE INSTRUCTIONS!When using an electrical furnishing basic precautions should always be followed, including the following:READ ALL INSTRUCTIONS BEFORE USING (THIS FURNISHING)WARNING:To reduce the risk of burns, fire, electric shock, or injury to persons:DANGER: To reduce the risk of electric shock:Always unplug this furnishing from the electrical outlet before cleaning.• Unplug from outlet before putting on or taking off parts.• Close supervision is necessary when this furnishing is used by or near children, invalids or diabled persons.• Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.• Never operate this furnishing if it has a damaged cord or plug, or if it is not working properly, dropped or damaged, or dropped into the water. Return the furnishing to a service center for examination and repair.• Keep the cord away from heated surfaces.• Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair and the like.• Never drop or insert any object into any opening.• Do not use outdoors.• Do not operate where aerosol (spray) products are being used or where oxygen is being administered.• To disconnect, turn all controls to the off position, then remove plug from outlet.SAFETY PRECAUTIONS
CUSTOMER SERVICE: 800-695-25404WARNING: Risk of Injury:Keep children away from extended foot support (or other similar parts).DANGER:Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded.Do not modify the plug provided with the product. If it will not fit the outlet, have a proper outlet installedby a qualified electrician.SAVE THESE INSTRUCTIONS!WARNING: Risk of electric shock: Connect this furnishing to a properly grounded outlet only.See Grounding instructions.GROUNDING INSTRUCTIONS:This product must be grounded. If it should malfunction or breakdown, grounding provides a path of leastresistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.SAFETY PRECAUTIONSL'AVERTISSEMENT: LE RISQUE DE CHOC ÉLECTRIQUEPOUR L’UTILISATION DU MÉNAGE/RÉSIDENTIELLE SEULEMENTN’UTILISEZ PAS DEHORSL'AVERTISSEMENT: N’UTILISE PAS PRÉS DE L’UTILISATION DE GENS OU DU PORTAGE DES ARTIFICES MÉDICAUX
CUSTOMER SERVICE: 800-695-25405This product is for use on a circuit having a standard rating of 120 volts and is factory equipped with a specific electric cord and plug to permit connection to a proper electric circuit. Make sure that the product is connected to an outlet having the same configuration as the plug. No adapter should be used with this product.If the product must be reconnected for use on a different type of electric circuit, the reconnection should bemade by qualified service personnel.Unauthorized modifications could void the electrical portion of your warranty. Failure to use a properlygrounded outlet for this product or modification of the plug will compromise this important grounding safetyfeature and may result in electrical shock, electrical fire, or faulty operation of the product. A.Grounded Outlet BoxGrounding PinGrounded Outlet Metal ScrewB.Grounded Outlet Box Tab ForGroundingScrewAdapterGrounding PinMetal ScrewC.AdapterTab ForGrounding ScrewMetal ScrewWARRANTY PRECAUTION:IN-HOME USE AND HOSPITAL DISCLAIMER: WARNING! Do not open control box, motors or wireless remote controls (with the exception of the battery compartmentif equipped). The warranty is void if these units are tampered with. Any repair or replacement of adjustableFoundation parts must be performed by an authorized technician.Your Adjustable Foundation is strictly designed for in-home use only. It is NOT designed for hospital use and is NOT designed to meet hospital standards. Do not use this bed with TENT TYPE oxygen therapy equipment or near explosive gases. DO NOT USE NEAR PEOPLE USING OR WEARING MEDICAL DEVICES. FOR HOUSEHOLD /RESIDENTIAL USE ONLY. DO NOT USE OUTDOORS. This product conforms to UL STD 962This product is for use on a standard 120-volt circuit, and has a grounding plug that looks like the plug illustrated in photo A (see Figure). A temporary adapter that looks like the adapter illustrated inphoto B and C able to be used to connect this plug to a 2-pole receptacle as shown in photo B if aproperly grounded outlet is not available. The temporary adapter should be used only until a properlygrounded outlet (photo A) can be installed by a qualified electrician. The green colored rigid ear, lug or the like extending from the adapter must be connected to a permanent ground such as a properlygrounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal screw.FOR BEST RESULTS, YOUR ADJUSTABLE FOUNDATION SHOULD BE PLUGGED INTO A SURGEPROTECTOR (not included).SAFETY PRECAUTIONS
CUSTOMER SERVICE: 800-695-25406IMPORTANT SAFETY FEATURES:Use this furnishing only for its intended use as described in these instructions. Do not use attachments notrecommended by the manufacturer.USER-SERVICEABLE PARTS:This product is specifically designed to have no maintenance by you, the user. Therefore, you are encouragednot to open any motors, alter the wiring, adjust, modify or change the structure of the product, as it willvoid the warranty.POWER RATINGS:INPUT: AC 120V - 60Hz, 1.5 AmpOUTPUT: DC 24V-3AFUSE: 1.5A 250VIf there is an overload weight condition on the head or foot mechanism, the control unit will automaticallystop all functions. Once the excess weight is removed the control unit will automatically allow all functions toresume operation after 30 seconds.As with any product that produces a vibrating motion, it is possible that some pacemakers may interpret thismotion as a false sense of movement and/or exercise. This may or may not affect your pacemaker.If you have any concerns, please consult your physician. For more information please contact customer service by calling 800-695-2540.The input transformer voltage is AC120V (1.5 Amp) 60HZ, and the output voltage is DC24V (3Amp).When there is a short-circuit, a fuse on the transformer will be blown in order to protect the electricalequipment (Fuse: 1.5A). Should the above situation occur, the customer should seek professionalassistance by calling a licensed electrician or by contacting customer service at 800-695-2540. SAFETY PRECAUTIONSAfter your Motion SIGNATURE Adjustable Foundation has been unboxed, immediately dispose of packaging as it can smother small children and pets. To avoid injury, children and pets should not be allowed to play on or under the bed. Children should not operate this product without adult supervision. Close supervision is necessary whenthis furnishing is used by, or near children, invalids, or disabled persons. SMALL CHILDREN AND PETS WARNING:
CUSTOMER SERVICE: 800-695-25407 SAFETY PRECAUTIONSSAVE THESE INSTRUCTIONS: Your Motion SIGNATURE Adjustable Foundation has been designed to provide you with the reliable operation and durability you expect. This product has been inspected and tested prior to shipment.RADIO FREQUENCY IS 433.92 MHZFCC COMPLIANCEThis device complies with part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void the user’s authority to operate the device. Note: Exceeding the recommended weight restrictions could damage your adjustable foundation and void your warranty and using a mattress on top of your adjustable foundation that is not designed for adjustability may also void your warranty. PRODUCT RATINGS:The lift motor in your Motion SIGNATURE Adjustable Foundation is NOT designed for continuous use. Reliable operation and full life expectancy will be attained as long as the lift motor does not operate more than two (2) minutes over an eighteen (18) minute period, or approximately 10% duty cycle. Any attempt to circumvent or exceed this rating will shorten the life expectancy of this product and may void the warranty. The recommended weight restrictions for your Motion SIGNATURE Adjustable Foundation is up to 850 lbs. total weight, including people and the mattress for all sizes of adjustable foundations. Lift speed will vary due to weight and mattress configuration, as well as the mattress type. The weight must be evenly distributed across the bed. This Product is not designed to support or lift 850 lbs of total weight in the head or foot sections of your Motion SIGNATURE Foundation alone, or in any unevenly distributed fashion. Some mattresses are not designed for Adjustable Foundations because they do not bend or flex well when adjusted. When using such a mattress with your Motion SIGNATURE Adjustable Foundation the weight limits set forth herein do not apply, as the bending of the mattress requires significant force and puts significant strain on the motors and the Adjustable Foundation itself. For best performance, you should enter and exit the adjustable bed while it is in the flat or fully lowered position.DO NOT SIT ON THE HEAD OR FOOT SECTIONS WHILE IN THE RAISED POSITION.INTENDED USAGE:The electric adjustable foundation should be installed with the head board brackets and/or the head of the frame positioned close to a wall.
Parts List rts List8NOTE: Before discarding any packing materials, check the adjustable bed frame carton and verifythe following items in the parts list are included:CUSTOMER SERVICE: 800-695-2540Motion SIGNATURE ADJUSTABLE FOUNDATION C.F.I.L.O.D.G .J.M.E.H.K.N.A. B.PARTS LISTA. Wireless Remote Control (1) and CR2477 3V Lithium battery (1) B. Pro-Fit™ Mattress Retainer System (4)C. Foundation Legs (4) D. Inner Headboard Bracket (2)E. Outer Headboard Bracket (2)F. Retainer Bar Bolt (8)G. Inner Headboard Bracket Bolt (4)H. Outer Headboard Bracket Bolt (4)I. Retainer Bar Plate (8)J. 5/16 Inch Washer (16)K. 5/16 Inch Locking Nut (8)L. Allen Key (1)M. Wrench (1)N. 9-Volt Batteries (2)O. Remote Stand (1)
CUSTOMER SERVICE: 800-695-25409 To avoid damage to the adjustable bed, always open the carton while the bed is laying in the FLAT position on the floor.IMPORTANT UNPACKING INSTRUCTIONSOPEN FLAT Carefully lift the bed frame unit out of the shippingcarton, keeping the unit top side down. For safetyreasons, this should be performed by 2 people.STEP 1. Assembling Bed Legs:Open the accessories box, take out the 4 legs, and thread them in a clockwise direction into the threaded holes in the frame.STEP 2 NOTE: Tighten the legs securely to the frame.Leave no space between leg and frame. STEP 3 Remove and extend the power cord from theframe.WARNING:POWER CORDS MUST NOT INTERFEREWITH ANY ADJUSTABLE BED MECHANISMS. Frame Assembly InstructionsRemove the plastic packaging from the adjustable foundation.STEP 4 Base overview A 3-outlet, 2M, 13A UL approved power strip is pre-installed to the adjustable foundation to serve as power cord to the power outlet. One of the outlets is used to power the adjustable foundation. The remained two outlets will be handy for the appliances near the foundations.
CUSTOMER SERVICE: 800-695-254010 STEP 7Install the batteries in your wireless remote control.Briefly activate all functions on the wireless remotecontrol to verify that all of the features are operational.If your Motion SIGNATURE foundation does NOT operate, please refer to the Troubleshooting section beginning on page 21 of this manual.STEP 9Use the Retainer Bolts (F) and Retainer Bar Plate (I) to fasten the Pro-Fit™ Mattress Retainer System (B) to the front of the bed Frame. (As shown in the diagram).NOTE: Use only a manual screwdriver to install the retainer bolts. DO NOT use a power screwdriver to tighten the bolts. DO NOT over tighten the mattress retainer hardware.NOTE: It is important to position the bottomof the headboard cross member a maximum distance of 3 inches (76.2 mm) between the headboard and the top of the mattress. Do not exceed 3 inches (76.2 mm).ATTENTION: Failure to follow the properinstallation instructions may result in damageto your adjustable bed frame.NOTE: If the adjustable frame is to be set upwithout a headboard, simply install a mattresson the frame. Installation is now complete. If a headboard is to be installed, proceed to step 10. DO NOTlean the bed against the installed legs to flip it over. ATTENTION ! Improper handlingPlug the power cord into a grounded electrical outlet.STEP 6Carefully rotate the base frame over to theupside up position.STEP 5 NOTE: An Electrical surge protection unit isrecommended (not included).Frame Assembly InstructionsReturn the bed to the flat position and proceed toassemble the Pro-Fit™ Mattress Retainer System. STEP 8Install the headboard brackets to the bed base frame. Place one bracket on the left-hand side ofthe base and one bracket on the right-hand side of the base.STEP 10
CUSTOMER SERVICE: 800-695-254011 Place your mattress on top of your adjustable frame.Typical Motion SIGNATURE foundation installation is now complete. If the bed is equipped with a programmable setting or options, refer to the Remote Control Guide for more information. Install the headboard brackets to the bed base frame. Place one bracket on the left-hand side of the base and one bracket on the right-hand side of the base.1. Use the remote control to raise the head of the bed in order to gain access to the bed base frame.2. Remove plastic cap and place the Inner Headboard Bracket (D) into the round tube frame making sure the bracket inserted into the round tube. This will create a box shape. Place the Headboard Bracket Bolt (G) with a 5/16 Inch Washer (J) through the pre-drilled hole in the round tube frame and pass it through the Inner Headboard Bracket. Use the 5/16 Inch Washer (J) and 5/16 Inch Locking Nut (K) and tighten the bolt in place. Repeat for the opposing side of the bed frame.Headboard Installation STEP 11 4. Firmly tighten the headboard bolts (not included) to the end of the headboard bracket assembly.5. Measure the distance of the center to center mounting holes in the headboard.6. Measure the distance of the center to center mounting holes in the headboard bracket assemblies.7. If the headboard brackets require adjustments, loosen the bolts that are holding the outer headboard brackets and move them to the necessary distance. Reinstall the bolts and firmly tighten.3. Place the open side of the outer headboard bracket (E) onto the exposed square tube of the inner head board bracket (D). This will create a tight fit between (D) and (E). Place a Headboard Bracket Bolt (H) with a 5/16 Inch Washer (J) through the Outer Headboard Bracket (E) and into the Inner Headboard Bracket (D). Use a 5/16 Inch Washer (J) and 5/16 Inch Locking Nut (K) and hand tighten to allow for adjustment. Repeat same procedure for opposing side of the bed frame.
Bluetooth Accessory Module User’s GuideCUSTOMER SERVICE: 800-695-254012Your Motion Signature adjustable foundation has a Bluetooth Accessory Module as standard equipment.The Bluetooth Accessory Module allows you to control your adjustable foundation with your mobile device using a free, downloadable app. The Module is compatible with the following devices:iPhone 4S or 5 seriesiPad 3 or lateriPod Touch 5th generationWiFi is not required for this device to operate.Type “ Serta Remote ” in the search column.Select the Serta Motion Signature app. Click Install to download the app.STEP 2STEP 3STEP 4NOTE:Once the App is installed, opening the app the Bluetooth Accessory Module will connect to your device automatically. STEP 1Please use your iPod Touch (5th generation), iPhone 4S or iPad 3 to log into the App store. How to download the App SoftwareNightlight Feature The LED light on the Bluetooth Accessory Module serves as a nightlight that can be controlled with the remote control or with your mobile device.
Bluetooth Accessory Module User’s GuideCUSTOMER SERVICE: 800-695-254013Operating InstructionsA, B. Head and Foot adjustment:• Raise and lower head and foot section of base.C. Zero Gravity:• Legs slightly above the chest, for bettercirculation.D. Bed “Flat” Button:• Levels the bed: Press and hold for 3 secondsto activate button.Note: To cancel, press buttons A or BE. Two programmable memory buttons:• You can store 2 personalized memory positions.• To set a memory position, press the “set” button• After programming the memory settings, press Memory button 1 or 2 and the bed will move to the position that you've set.when you are in your desired position, then pressthe 1 or 2 memory button to lock in the position.F. Anti-Snore:• Raises the head slightly for easier breathing.G, H. Head and foot massage controls:• Starts at an intensity of 5 out of 10.• To increase massage intensity, press (︿) button.• To decrease massage intensity, press (﹀) button.Note: The lowest setting will turn off thecorresponding massage unit.A.C.E.B.M.D.F.G.I.K.H.M.J.L.I. Massage stop button:• Press for 2 seconds to stop all massage features.J. Full body massage function:• Turns on both head and foot massage motorsand alternates between Wave mode 1 & 2.Note: You must stop the massage before you can switch to another wave function or to the full body massage.K. Nightlight ON / OFF :• Turns on LED lights up.The default shut off time can be adjusted in the app.ATTENTION:If FLAT BUTTON (D) is pushed, massage motors will stop until bed is flat. Massage resumes in 30 seconds.L. Wave massage mode:• Turns on both head and foot massage motors to one of the 2 wave functions.ATTENTION:If FLAT BUTTON (D) is pushed, massage motors will stop until bed is flat. Massage resumes in 30 seconds.M. Menu Interface Screen 1 Interface Screen 2
Bluetooth Accessory Module User’s GuideCUSTOMER SERVICE: 800-695-254014Adjust Night Brightness:Adjust the brightness setting of the nightlight. You will see the nightlight get brighter and dimmer as you move right or left.Customer Support:Please contact us if you have questions or concerns about your adjustable foundation.
Wireless Remote ControlCUSTOMER SERVICE: 800-695-254015 LED LIGHTG. RAISE(▲) / LOWER (▼)E. RAISE (▲) / LOWER (▼) FOOT SECTION OF THE BASEB. ZERO GRAVITYA. ANTI SNORED. PROGRAM UP TO 2 MEMORY POSITIONSJ. INCREASE (+) / REDUCE (-) MASSAGE INTENSITY ON HEAD SECTION OF THE BASEH. INCREASE (+) / REDUCE (-)F. NIGHTLIGHT ON / OFF MASSAGE INTENSITY ON FOOT SECTION OF THE BASEK. SELECT 1 OF 2 MASSAGE WAVE SPEEDSL. STOP ALL MASSAGE FEATURESI. TURNS ON THE FULL BODY MASSAGE FUNCTIONC. RETURN ALL SECTIONS TO THE FLAT POSITION HEAD SECTION OF THE BASE
CUSTOMER SERVICE: 800-695-254016 HEAD AND FOOT ADJUSTMENT (E, G)• Adjusts the head and foot sections to the desired positions. PROGRAMMABLE MEMORY BUTTONS (D)NIGHTLIGHT ON / OFF (F)BED “FLAT” BUTTON (C)• Levels the bed to the flat position when the button is pressed and held for at least 1 second. NOTE: The “FLAT” cycle can be interruptedand cancelled by pressing the head or footadjustment buttons (E, G). ZERO GRAVITY (B)• Allows your legs to be lifted to a position slightly above the chest, which enables blood flow to easily circulate back to the heart, thus reducing stress and fatigue.ANTI SNORE (A)• Raises the HEAD to an upright position for anti-snore.NOTE: The lowest setting will turn off thecorresponding massage unit.WAVE MASSAGE MODE (K)• Turns on both head and foot massage motors to one of the 2 wave functions.NOTE: You must stop the massage beforeyou can switch to another wave functionor to the full body massage. MASSAGE STOP BUTTON (L)• Press for 2 seconds to stop all massage features.NOTE: The massage feature is designedto automatically shut off after 30 minutes of continuous use. FULL BODY MASSAGE FUNCTION (I)• Turns on both head and foot massage motors and alternates between Wave Modes 1 & 2 .You can store 2 personalized memory positions• To Set a Memory Position: When in desired position, press and hold Memory button for more than 5 seconds until the LED light flashes 3 times to signal Memory position is stored. • To Recall a Memory Position: Press Memory button 1 or 2 until LED lights up. ATTENTION: If the massage motors are operating and Head and Foot lift or Memory buttons are pressed, the massage motor will stop and resume operating after lift position reached. But if Flat button is pressed, the massage motors will not resume after flat position reached. HEAD AND FOOT MASSAGE CONTROLS (H, J)• Turns on the corresponding massage unit (starting at intensity 5 of 10)• Slowly increases or decreases massage intensity.To increase massage intensity, press (+) button.To decrease massage intensity, press (+) button.NOTE: Do not hold the Memory button for more than 5 seconds otherwise a new memory position will be set.NOTE: The default nightlight automatically shut off time is 8 hours unless adjusted fromthe App.Remote Control Operation Guide• Turns on LED lights up.
Remote Control Operation GuideCUSTOMER SERVICE:800-695-254017Safety: Notice: • If there is an overload weight condition on the head or foot mechanism, the control unit will automatically stop all functions.NOTE: Once the excess weight is removed, the control unit will automatically start all functions after 30 seconds.• If the massage motors are continuously used for a 30 minute period, the motors will automatically shut down.• The input transformer voltage is AC 120V 60 HZ, the output voltage is DC 24V 3A. When there is a short circuit, a fuse on the transformer will be blown in order to protect the electrical equipment (Fuse: 1.5A).The changes or modifications not expresslyapproved by the party responsible forcompliance could void the user’s authority tooperate the equipment.Important Note • To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. THIS DEVICE COMPLIES WITHPART 15 OF THE FCC RULES.OPERATION IS SUBJECT TO THEFOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSEHARMFUL INTERFERENCE (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,INCLUDING INTERFERENCE THATMAY CAUSE UNDESIREDOPERATION.• The buttons are backlit, when a button is pressed,to aid in the visibility of the remote in low light environments.NOTE: This bed may have minor intermittentperformance due to RF Interference. This is a normal operation of the bed and is not a defect.• The Motion SIGNATURE adjustable foundation uses a RF (Radio Frequency) remote control system. Additional Remote Features:• Customers can control the remote without facing the receiver (best transmission range is within 9 feet or 3 meters).ATTENTION: When the above situation occurs, the customer MUST seek professional assistance.
CUSTOMER SERVICE: 800-695-254018 Note: The remote that comes with the bed is already paired with your bed. No further action is required. Only replacement remote controls require user programming.Place 3V Lithium battery into the remote control.Ensure the bed is plugged into a functioning outlet. Press the learn button for 3 seconds. NOTE: If a new signal is not received, it willreset itself to normal mode in 10 seconds. When the Green LED signature light illuminates,the RF frequency code setting function will be activated.STEP 5Figure 1: Press “Learn Button” to initiatethe RF learning Mode.Press any button on the remote control.Replacement Remote Control ProgrammingSTEP 4STEP 5STEP 1STEP 2STEP 3When the receiver light flashes, you have completed the learning process of the RF frequency code.Figure 2: A flashing Green LED indicates thecontrol box has received the remote controlsignal.1 Wireless Remote Control and 2 Motion SIGNATURE adjustable foundationsSTEP 6PAIRING INSTRUCTIONSFOR JOINING 2 FOUNDATIONSUse the same remote control to pair with the two adjustable foundations one after the other following the “ Replacement Remote Control Programming” procedures (Step 3 ~ Step 6).
CUSTOMER SERVICE: 800-695-254019 Locate and remove the cover for the 9 voltbatteries.Install the two (2) alkaline 9 volt batteries. Your bed should lower to the flat position.NOTE: The two (2) 9 volt batteries are only intended to be used once. After you complete the emergency lowering, the batteries need to be replaced with new alkaline batteries.Your Motion SIGNATURE adjustable foundation has an emergency lowering feature in the event that your base is in the raised position and has lost power due to a power outage. Figure 2: Install 9 volt batteries. Figure 1: 9 volt batteries cover.Press the “FLAT” button (C) or the individual lowering buttons (E, G) to lower the foundationto flat position.Remove the two 9 volt batteries and replace the battery cover.Figure 3: Remove the batteries and replace the battery cover.Remote Control Emergency Power Down FeatureSTEP 3STEP 4STEP 1STEP 2
CUSTOMER SERVICE: 800-695-254020 Remote Stand User’s GuideTo avoid accident or injury, please read the Mfollowing instructions before use.1. The stand is for indoor use only.2. To reduce the risk of electrical shock or fire, don't expose the unit to rain or excessive moisture.3. Plug the remote stand into the power strip as in the diagram to avoid a short circuit.4. To avoid electrical shock, do not insert objects other than electrical plugs into outlet openings.5. Before use, please ensure local voltage and power are in accordance with the remote stand requirements.6. Do not make any changes or modifications to the remote stand. Failure to comply will void the manufacturer's warranty.7. Do not use the stand if the stand has been damaged in any way.8. Please don't attempt to disassemble the remote stand.9. To clean, unplug the remote stand from the power strip and use a damp cloth.I. Profile of Remote Stand1. Refer to drawing in Part I. Plug the remote stand into the 120V AC power strip outlet under the bed.2. Plug light electrical devices into the remote stand outlets as desired.3. Plug USB cord in front to charge your mobile devices.4. Place your remote in the cradle of the front side of the stand for storage.INSTALLATION DIAGRAMPower Strip OutletAC PlugIndicatorLampPowerOutlet USBChargerBack SideFront SideElectrical ApplianceII. InstallationIII. Specifications1. Model Number: RC-STAND-S012. Power Rating: AC120V, 300W3. Housing: ABS4. Indicator Lamp: 1/4 W power on lamp5. Outlets: 2 outlets on back of stand6. Cable: 1.8M / UL7. Surge Protection: 125 joules8. USB Charger : 5V, 1ACaution:This device is only to be used to control light household electrical appliances such as lamps, phone chargers, and laptop computers.You should never plug heaters or other items with heating elements into this device.
CUSTOMER SERVICE: 800-695-254021 In the Event the Motion SIGNATURE adjustable foundation fails to operate, investigate the symptoms and possible solutions provided in the chart below : TroubleshootingRemote control LED will not illuminate. NOITULOSMOTPMYSNo features of the Motion SIGNATURE adjustable foundation will activate. Head or foot section will elevate but will notreturn to the horizontal (flat) position.Head or foot lift function has minorinterference during operation.• Verify the power cord is plugged into a working, grounded electrical outlet. A grounded, electrical surge protection device is recommended. Test the outlet by plugging in another working appliance. • Replace the batteries in the hand control. Ensure the batteries are installed correctly.• The bed mechanism may be obstructed. Elevate the bed and check for an obstruction. Remove the obstruction.• The head section may be too close to the wall. The headboard may be too close to the edge of the mattress. Verify a 1.5” (38.1mm) to 2” (50.8mm) distance is between the headboard brackets and the mattress. Adjust if required.• Check batteries in remote, replace if necessary. Make sure that you are following the duty cycle of the motors (do not operate more than three (3) minutes over a thirty (30) minute period, approximately 10% duty cycle).• Press the lift buttons squarely & accurately. Remote may be experiencing common Radio Frequency Interference from other radio transmitting devices.Excessive massage motor noise.• If the bed is located on hard surface flooring, place carpet pieces.• Elevate the head or foot section a short distance (with the hand control) to realign the lift/lower mechanisms with the bed support platform.• Verify that the bed is not positioned against a wall, nightstand, or other object that may cause the vibration or noise.• If the Motion SIGNATURE is installed over a bed frame, verify the massage motors are not causing the bed frame (or bed frame components) to vibrate.• Verify that the headboard attachment hardware is firmly tightened (if used).Remote control LED illuminates and appearsto be operable but will not activate the bed.• Program the remote control (see the Remote Control Guide, included with this product, for programming procedures). If equipped with a power down box, make certain the power down box is easily accessible. Relocate the power down box if required.• Unplug the power cord, wait 45 seconds and plug it in to reset the electronic components.• The electrical circuit breaker may be tripped. Check the electrical service breaker box to verify.• The surge protection device or electrical outlet is defective. Test the outlet by plugging in another working appliance.
Register Online. For easy registration of your warranty visit www.reverie.comPlease prepare a digital copy of your proof of purchase (invoice or sales receipt) when registering online. 25 YEAR LIMITEDWARRANTY NamePhoneAddressCity State/Province ZIP/Postal CodePurchase dateBed Serial NumberEmail Address1-Year Parts and Labor WarrantyYour Serta® Motion SIGNATURE™ adjustable base is warranted by the manufacturer against defects in materials or workmanship for a period of one year from the date of purchase to the original Purchaser. During such time, the manufacturer will repair or replace, at no cost to the original Purchaser any warranted part found to be defective by the manufacturer, in its sole discretion. This includes all pre-authorized labor and transportation costs incurred with the repair or replacement of any warranted part found to be defective. This warranty does not apply to Serta® Motion SIGNATURE™ adjustable base floor models. This one (1) year warranty does not apply if Purchaser does not return all defective parts to the manufacturer within 15 days of Purchaser’s receipt of replacement part(s).2-Year Motor WarrantyYour Serta® Motion SIGNATURE™ adjustable base linear actuators are warranted by the manufacturer against defects in materials or workmanship for a period of two (2) years from the date of purchase to the original Purchaser. During such time, the manufacturer will repair or replace, at no cost to the original Purchaser any warranted linear actuator found to be defective by the manufacturer, in its sole discretion. This includes all pre-authorized labor and transportation costs incurred with the repair or replacement of any warranted part found to be defective by the manufacturer, in its sole discretion. This warranty does not apply to Serta® Motion SIGNATURE™ adjustable basefloor models. This two (2) year warranty does not apply if Purchaser does not return all defective parts to the manufacturer within 15 days of Purchaser’s receipt of replacement part(s).Years 2 through 5 – Coverage of Parts OnlyDuring Year 2 through 5 from the original purchase date, the manufacturer will replace any warranted part on the adjustable base found to be defective by the manufacturer, in its sole discretion, to the original Purchaser. The manufacturer’s liability is limited to the replacement of the defective warranted electrical/mechanical part(s)* ONLY with the original Purchaser responsible for all service, installation, handling, shipping, and transportation cost of said part(s) (except where prohibited by law). This warranty does not apply to Serta® Motion SIGNATURE™ adjustable base floor models. This warrantydoes not apply if Purchaser does not return all defective parts to the manufacturer within 15 days of Purchaser’s receipt of replacement part(s).25-Year Limited WarrantyDuring Year 6 through 25 from the original purchase date, the manufacturer will replace, within the terms and conditions set forth in this paragraph, any Serta® Motion SIGNATURE™ adjustable base mechanical part(s)* found to be defective by the manufacturer, in its sole discretion to the original Purchaser. To register your warranty via mail , send this portion and a copy of your proof of purchase (invoice or sales receipt) to: Reverie Warranty Dept. 341 Central Avenue, Silver Creek, NY 14136 (1-800-695-2540)22Purchaser shall pay 1/20 of the current replacement cost of the defective part multiplied by the number of years after the fifth year, from the original purchase date. This warranty applies only to the replacement part(s); the Purchaser will be responsible for all service, installation, handling, shipping, and transportation cost of said part(s). Purchaser may also be subject to other charges for said part(s). The manufacturer’s liability shall be limited to the replacement of the defective part(s) ONLY with the Purchaser responsible for all service, installation and freight cost for said part(s) (except where prohibited by law). This warranty does not apply to Serta® Motion SIGNATURE ™ adjustable base floor models. This warranty does not apply if Purchaser does not return all defective parts to the manufacturer within 15 days of Purchaser’s receipt of replacement part(s). 2-Year Floor Model WarrantyYour Serta® Motion SIGNATURE™ adjustable base floor model is warranted against defects in warranted electronic parts for a period of two (2) years from the date of purchase to the original Purchaser. During the first two (2) years the manufacturer will replace at no cost to the original Purchaser, any defective electronic part(s) determined to be defective by the manufacturer, in its sole discretion. The manufacturer’s liability is limited to the replacement for the defective electronic part(s) ONLY with the Purchaser responsible for all service, installation, handling, shipping, and transportation cost of said part(s). This two (2) year warranty does not apply if Purchaser does not return all defective parts to the manufacturer within 15 days of Purchaser’s receipt of replacement part(s). *Warranted Parts under this Motion SIGNATURE ™ Warranty are as follows:Additional terms and conditions apply. See next page for details.a) Head/Foot Linear Actuatorc) Control Box with Power Supplye) Mounting Bracketsb) Massage Motors and Housingd) Remote Controlf) Support StrutsManufactured by Reverie for Serta®.For warranty service, call Customer Service 1-800-695-2540341 Central Avenue, Silver Creek, NY 14136warrantyservice@reverie.com www.reverie.com
This warranty does not include reimbursement for inconvenience, removal, part(s) installation, bed set up, loss of use, normal wear and tear, shipping or any other costs or expenses not expressly covered in this warranty. To the extent permitted by law, the determination of whether any part and/or workmanship is defective and the decision to repair and/or replace any defective parts under this Limited Warranty shall be made exclusively by the manufacturer in its sole and absolute discretion.A. Any damage resulting from any misuse or abuse caused by the Purchaser or any third party.B. Any damage caused by repairs or parts replacement by any unauthorized person(s).C. Damage caused if the adjustable base has been mishandled (including during shipping, transit, or by other means), subject to physical or electrical misuse or abuse, or by failing to adhere to the Owner’s Manual and this warranty including the operation of the adjustable base in any way inconsistent with the operation and maintenance procedures in the Owner’s Manual.D. Damaged mattresses, foundation cover(s), fabric(s), bedding cables, electrical cords or accessories supplied by dealers or any third party.Contact your dealer for warranty information on these items.E. Modification of the Serta® Motion SIGNATURE™ adjustable basewithout prior written consent by the manufacturer.F. Costs for unauthorized service calls for the purpose of educating the consumer about the Serta® Motion SIGNATURE™ adjustable base, locating proper functioning power outlets, or installing batteries.G. Damage if the recommended weight restrictions are exceeded.H. Damage if used in any environment or a commercial setting which was not intended.I. Damage to foam shroud, fabric cover, or wooden support by improper handling or misuse.In addition, this warranty shall be void in the following circumstances:The following exclusions/limitations are inapplicable to consumers residing in Québec: OTHER THAN AS EXPRESSLY SET OUT HEREIN, AND TO THE EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER ORAL OR WRITTEN WARRANTIES, REPRESENTATIONS, CONDITIONS OR PROMISES, WHETHER EXPRESS OR IMPLIED, AND WHETHER ARISING BY LAW, STATUTE, COURSE OF DEALING OR USAGE OF TRADE, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES AND CONDITIONS OF MERCHANTABILITY, QUALITY, DURABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT PERMITTED 23To the extent permitted by law, this warranty is not transferable and will automatically terminate if the original Purchaser sells or otherwise disposes of the Serta® Motion SIGNATURE™ adjustable base. This warranty gives the Purchaser specific legal rights. Other rights, which vary from jurisdiction to jurisdiction, may exist. In addition, some jurisdictions do not allow (i) the exclusion of certain warranties, (ii) limitations on how long an implied warranty lasts and/or (iii) the exclusion or limitation of certain types of costs and/or damages, so the above limitations may not apply. This warranty is only valid in The United States, Canada and Puerto Rico. The laws of the Purchaser’s state/province of residence shall govern thiswarranty. REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE PURCHASER. THERE SHALL BE NO LIABILITY ON THE PART OF ASCION, L.L.C., AND ITS PARENTS, SUBSIDIARIES, DIVISIONS OR AFFILIATES FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSE-QUENTIAL DAMAGES OR FOR ANY OTHER DAMAGE, CLAIM, OR LOSS NOT EXPRESSLY COVERED BY THE TERMS OF THIS WARRANTY. ADDITIONAL TERMS & CONDITIONSTo the extent permitted by law, this Limited Warranty does not include reimbursement for inconvenience, removal, installation, setup time, loss of use, shipping, or any other costs or expenses. Where any term of this Limited Warranty is prohibited by local law, such term shall be null and void or shall be deemed modified so as to be consistent with local law, and, in either case, the remainder of this Limited Warranty shall remain in effect. This product is not rated to support weights in excess of 850 pounds inclusive of the mattress and bedding. The base will structurally support this weight, provided it is evenly distributed across the top surface of the bed base. The adjustable base is not designed to support or lift this amount in the head or foot sections alone, and it is not designed to lift this amount of weight. The amount of weight the bed can lift without exceeding the safety shut-off threshold for the control box depends on distribution of weight and how well the mattress on top of the base bends with the adjustable base. Exceeding this weight restrictions or loading weight on the bed unevenly or using a mattress that is not designed to flex well with an adjustable bed could damage the bed and/or cause injury and will void the warranty. Weight Limits: BY APPLICABLE LAWS, ANY IMPLIED WARRANTIES (IF APPLICABLE) ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. TO THE EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE MANUFACTURER BE LIABLE FOR ANY SPECIAL, INCIDENTAL, PUNITIVE, EXEMPLARY, CONSEQUENTIAL OR SIMILAR DAMAGES, WHETHER OR NOT FORESEEABLE. Manufactured by Reverie for Serta®.For warranty service, call Customer Service 1-800-695-2540341 Central Avenue, Silver Creek, NY 14136warrantyservice@reverie.com www.reverie.com
24 Serta® Motion SIGNATURETM Limited Warranty Register Online. For easy registration of your warranty visit www.reverie.comPlease prepare a digital copy of your proof of purchase (invoice or sales receipt) when registering online.Manufactured by Reverie® for Serta®.For Warranty and Service:800-695-2540warrantyservice @ reverie.com341 Central Ave. Silver Creek, NY 14136 www.reverie.comTo register your warranty via mail, send this portion and a copy of your proof of purchase(invoice or sales receipt) to:Reverie Warranty Dept. 341 Central Ave. Silver Creek, NY 14136 (800-695-2540)NamePhoneAddressCity State/Province ZIP/Postal codePurchase dateBed Serial NumberEmail Address

Navigation menu