Ashdown Design And Marketing Abm Rpm 1 Users Manual
MAG 300 to the manual b17c446d-a61b-4f93-b192-be9969ce9b9b
2015-02-06
: Ashdown-Design-And-Marketing Ashdown-Design-And-Marketing-Abm-Rpm-1-Users-Manual-498524 ashdown-design-and-marketing-abm-rpm-1-users-manual-498524 ashdown-design-and-marketing pdf
Open the PDF directly: View PDF 
.
Page Count: 6
| Download | |
| Open PDF In Browser | View PDF |
Park Farm • Inworth • Colchester • Essex • CO5 9SH http://www.ashdownmusic.com O perating I nstructio ns ABM/RPM-1 Amplifier Heads and ABM Combos MAG 300 Amplifier Head and Combos Electric Blue 180 Amplifier Head and Combos The ABM Design Philosophy This is a NO COMPROMISE design using the best parts available wherever possible. The lightning flash with the arrow head symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated ‘dangerous voltage’ within this product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying this product. Some examples of this are as follows: • • • • • GROUNDING INSTRUCTIONS • This product must be grounded (earthed). If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a supply cord having an equipment grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with the local codes and ordinances. DANGER - Improper connection of the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product – if it will not fit the outlet, have a proper outlet fitted. The wires in this mains cord are coloured in accordance with the following code: Green & Yellow - Earth Blue - Neutral Brown - Live CE MARK FOR EUROPEAN HARMONISED STANDARDS The CE mark which is attached to these products means it conforms to EMC Directive (89/69/EEC), CE mark Directive (93/68/EEC) and Low Voltage Directive (72/23/EEC). • • • • • • Gold plated jack sockets for reliability and long life. Full metal XLR sockets for strength and their positive latching facility. Powerful output stages for extra headroom (rated in English RMS real power and not MUSIC or PEAK power as these can claim to be 2 or 3 times the actual real power of the amplifier). Doubling up of the cooling fans for reliability and reduced fan noise (2 fans can run at half the speed to provide the same cooling capacity and as a consequence generate only half the noise of one fan running at twice the speed). Speed controlled fan drive circuit. Again this reduces the amount of fan noise as the fans run slow when the unit is cool and increase in speed with output power demands. Powerful TOROIDAL mains transformer. This is more expensive than a laminated stack transformer but has better regulation, i.e., provides more power on demand without sagging out and also has a minimal external magnetic field which means that single coil pick up basses are less likely to pick up mains hum from the amplifier. FET input circuit to the preamp for ‘Warmth’ even when using the CLEAN input mix setting. D.C. heaters for the TUBE section for low noise operation. Switch on delay for silent power up. Thermal trip for output protection. Relay switched speaker output lines for silent power down. Sub Bass output and Sub Harmonics facility for really serious bottom end. Everything possible has been done to make this a reliable, top of the range, minimum service, high quality, long lasting powerful bass amplifier. We know you will appreciate the effort that has been put into the design and manufacture of this unit and you will be rewarded in your choice of bass amplifier by long life and reliability. Fro nt Panel Facilities ABM, RPM-1, MAG 300 & ELECTRIC BLUE 180 ABM/RPM-1 DEEP (Electric Blue 180 & MAG 300) With this button IN, a fixed E.Q. is superimposed on the preamp to give a BASS boost to the sound.This gives +8dB at 50Hz. BRIGHT (Electric Blue 180 & MAG 300) With this button IN, a fixed E.Q. is superimposed on the preamp to give a TREBLE boost to the sound. This gives +10dB at 10kHz. MAG 300 Electric Blue 180 INPUTS On the MAG 300 and Electric Blue 180, there are two choices of instrument input, these are marked HIGH and LOW.The HIGH input is high sensitivity and also high impedance to suit the output from PASSIVE basses.The LOW input is low sensitivity and lower impedance to suit the output from ACTIVE basses.The ABM has a single instrument input provided, linked to a PASSIVE/ACTIVE selector switch (switch out=PASSIVE, switch in=ACTIVE). INPUT CONTROL The INPUT control sets the signal level through the preamp in conjunction with the INPUT LEVEL VU Meter (Electric Blue 180 uses a LED display).This is adjusted to give a reading of 0VU on the meter (yellow LED on Electric Blue 180) for average playing dynamics with occasional peaks into the red (red LED on Electric Blue 180) region. Please note that this setting may require re-adjustment after modification of the EQ controls. PUSH FLAT / SHAPE (ABM/RPM-1 only) With this button in its OUT position a fixed E.Q. is superimposed on the preamp to give a bright but punchy character to the sound. Pushing this button IN returns the preamp to a Flat frequency response. This function may also be controlled from a footswitch. For the footswitch to operate, this button must be in its OUT position. VALVE DRIVE (ABM/RPM-1 only) This routes the signal either through a clean Solid State amplification section (control on zero) or through a Dual Triode Tube amplification/overdrive section to add either tonal character, i.e. warmth with the control set at 9 o’clock, a slight edge in the sound at 12 o’clock, through to an increasing degree of Tube distortion/overdrive as the control is advanced to maximum. A Mix of these two amplification sections can be achieved with this control. N.B.The degree of Tube distortion with this control will also depend on the setting of the INPUT control. VALVE DRIVE IN/OUT (ABM/RPM-1 only) This push button switches the valve drive section IN or OUT.This function may also be controlled from a footswitch. For the footswitch to operate this button must be in its OUT position. E.Q. IN / OUT This button switches the Equalisation section IN or OUT, i.e., the Bass, Middle and Treble controls and the two sets of sliders (rotary controls on Electric Blue 180) placed between these.This facility is footswitchable on the ABM/RPM-1 range via a socket on the rear panel. For the footswitch to operate this button must be in its out position. EQUALISATION This consists of BASS, MIDDLE and TREBLE controls with two sliders (rotary controls on Electric Blue 180 & MAG 300) placed in between.This can be used in a number of ways: • Firstly as a very simple Bass, Middle and Treble tone control section as found on older traditional amplifiers. This is done by leaving the two sets of sliders (rotary controls on Electric Blue 180 & MAG 300) set in their centre positions and using only the BASS, MIDDLE and TREBLE controls to alter the overall tone. • Secondly, if more control is required, then the sliders (rotary controls on Electric Blue 180 & MAG 300) can also be used to tailor the E.Q. in the regions between the main tone controls. This provides a very versatile Equalisation section that is simple to understand and operate, yet provides a wide degree of variation. It retains the simplicity of a three-control tone section but provides the flexibility of a graphic equaliser. SUB HARMONICS This section consists of an IN / OUT switch and a LEVEL control.When switched IN, Sub Harmonics an octave below the notes being played are produced.The level of these Sub Harmonics relative to the straight bass sound can be adjusted using the LEVEL control.This is very effective in thickening the sound and you will find in use that only a small degree of this lower octave is required to really fill out the sound and provide a character to the sound that is not possible by any other means.The degree of Sub Harmonics is also dependant on the setting of the BASS control.This facility is footswitchable on the ABM/RPM-1 range via a socket on the rear panel. For the footswitch to operate the Sub Harmonics must first be switched into circuit with the front panel push button. DIRECT INJECT (D.I.) A balanced D.I. is provided on the front panel rugged metal latching XLR socket.The ABM/RPM-1 features a push button placed below the XLR that allows the user to choose either a Pre E.Q. / Pre Sub signal or a Post E.Q. / Post Sub and Effects signal (the Pre E.Q. signal also includes the Shape facility, if this is switched into circuit) – EBs and MAGs feature a Post E.Q. / Post Sub and Effects signal.The output signal from this XLR socket is set to a level and impedance suitable for connecting directly into the Microphone input of a mixing desk for either Direct Injection into the PA system or for recording.This must ONLY be used into a Balanced Microphone input. It is not intended for any other type of connection.This has a floating ground that is referenced to the mixing console it is plugged into and should not need ground lifting. It is also unaffected by Phantom Powering on the Microphone input. Make sure your XLR plug does not have the shell of the plug internally connected to the ground signal or this will connect the system to the chassis ground of the amplifier and may cause problems with hum. PUSH TO MUTE (ABM/RPM-1 only) When pushed IN this button mutes the output from the preamp to the power amp, mutes the output from the D.I. socket and mutes the output from the Sub Out socket as well.This leaves the output from the TUNER / LINE socket still available to allow muted tuning. An LED is provided next to this switch to indicate when the amplifier is muted.This operates only from the front panel MUTE push switch, i.e. pressing this button mutes all sound from the amplifier and allows a tuner connected to the TUNER / LINE socket to operate for silent tuning. Release the button and you are back in action again. Fro nt/ Rear Panel Facilities ABM, RPM-1, MAG 300 & ELECTRIC BLUE 180 TUNER / LINE OUT This output socket provides a line level signal that can be used either for a permanent connection to a tuner or a line output to slave up to other power amplifiers. (ABM/RPM-1 users - Please note that if this socket is used as a slave output to other power amplifiers that the MUTE button will not mute the signal to the external power amplifiers.) SUB OUT (ABM/RPM-1 only) This output socket provides a Low Pass filtered output for connection to a power amplifier driving a sub unit for additional extra-low bottom end.This may also be used to drive other power amplifiers to provide additional low bottom end to the system.The Low Pass filter is fixed at 160Hz. OUTPUT LEVEL The OUTPUT control adjusts the overall level of the amplifier. Adjust this for your preferred overall stage playing volume. 300 / 500 WATT ABM HEAD / COMBO REAR PANEL FACILITIES LINE INPUT (ABM/RPM-1 only) The rear panel has a Line Input socket for connection of other signal sources into the system.This can be used for plugging a CD,Tape or MiniDisc player into the amplifier for practising or rehearsing or for connection of a second preamp into the system. 47 42 0 39 3 2 1 12 10 0 RPM1 RACK-MOUNT PREAMP 65 95 SPEAKER OUTPUT (except Rack Preamp RPM1) The Speaker Output sockets are also situated on the rear panel of the unit.The ABM provides both jack and speakon connectors. 52 9 CROSSOVER AND OUTPUTS (Rack Preamp RPM1 only) The BASS MAGNIFIER RACK PREAMP RPM1 has a built in high precision CROSSOVER with separate jack socket outputs for the HIGH PASS and LOW PASS signals. Crossover frequency is adjustable from 35Hz to 160Hz with a level control for the LOW PASS output to adjust the balance between LOW and HIGH outputs signals.There is also a FULL RANGE jack line output provided.This section is provided with switched output levels for simplified connection to power amplifiers that require either a 0dB or +4dB signal level.This switches the levels of all three outputs. 58 6 35 5 75 o 8 I 0 4 7 FOOTSWITCH SOCKETS (ABM/RPM-1) Two stereo jack sockets marked SUB/VALVE and EQ/SHAPE are provided for connection of 2-way push on/push off type foot switches.The SUB footswitch mutes the Sub Harmonics when closed. For this to operate the Sub Harmonics must already be activated with the front panel push switch. For all other footswitches to operate, the corresponding front panel push buttons must be in their OUT position. 900 WATT ABM HEAD / COMBO 15 EFFECTS SEND / RETURN (rear panel on ABM/RPM-1 & front panel on MAG 300 & Electric Blue 180) A serial effects loop is provided at a level of 0dB.The Effects Send and Return sockets for this are on the rear panel of the ABM/RPM-1 and front panel of the MAG 300 and Electric Blue 180 below the D.I. socket. The EFFECTS SEND socket can also be used as a Line Out socket if required.The signal path through the preamp is only broken when a jack plug is inserted into the EFFECTS RETURN socket.The EFFECTS SEND is situated after the EQ,Valve section and Sub Bass Processor. Specificatio ns ABM, MAG 300 & ELECTRIC BLUE 180 PREAMPS INPUTS High Input Low Input Line Input (ABM only) Effects Return Impedance Impedance Impedance Impedance 3.9M Ohms 10K Ohms 22K Ohms 22K Ohms Input Input Input Input range 150mV to 20V p-p range 300mV to 40V p-p level 0dBu nominal level 0dBu nominal Level Level Level Level Level Level Level 0dBu nominal 0dBu nominal 0dBu nominal -20dBu nominal switched 0/+4dBU switched 0/+4dBU switched 0/+4dBU OUTPUTS Tuner Output Sub Output (ABM only) Effects Send D.I. Output Low Pass (RPM1 only) High Pass (RPM1 only) Full Range (RPM1 only) Speaker Outputs Impedance 22K Ohms Impedance 22K Ohms Impedance 22K Ohms 600 Ohms balanced Impedance 1K Ohms Impedance 1K Ohms Impedance 1K Ohms Minimum impedance 4 Ohms EQUALISATION (Electric Blue 180 & MAG 300) EQUALISATION (ABM) Bass Lo Mid Middle Hi Mid Treble Deep Bright Signal to Noise Distortion Shape (Push Flat) +/-15dB @ 100Hz +/-15dB @ 220Hz +/-15dB @ 660Hz +/-15dB @ 1.6kHz +/-15dB @ 7kHz shelving +8dB @ 50Hz +10dB @ 10kHz Better than 80dB (EQ flat) Less than 0.5% THD Bass Middle Treble Slider1 Slider 2 Slider 3 Slider 4 +8dB @ 50Hz & 4kHz, -8dB @ 400Hz, filter slope - 6dB/octave +/-15dB @ 45Hz +/-15dB @ 660Hz +/-15dB @ 7kHz shelving +/-15dB @ 110Hz +/-15dB @ 340Hz +/-15dB @ 1.3kHz +/-15dB @ 2.6kHz GENERAL SPECIFICATION Frequency Response Rack Preamp RPM1 Crossover Power Requirements -3dB at 17Hz and 30KHz (Electric Blue 150: -3dB at 22Hz and 25KHz) Variable between 35 and 160Hz 230 / 115V Park Farm • Inworth • Colchester • Essex • CO5 9SH E-mail: info@ashdownmusic.co.uk
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Page Count : 6 Profile CMM Type : Lino Profile Version : 2.1.0 Profile Class : Display Device Profile Color Space Data : RGB Profile Connection Space : XYZ Profile Date Time : 1998:02:09 06:49:00 Profile File Signature : acsp Primary Platform : Microsoft Corporation CMM Flags : Not Embedded, Independent Device Manufacturer : IEC Device Model : sRGB Device Attributes : Reflective, Glossy, Positive, Color Rendering Intent : Media-Relative Colorimetric Connection Space Illuminant : 0.9642 1 0.82491 Profile Creator : HP Profile ID : 0 Profile Copyright : Copyright (c) 1998 Hewlett-Packard Company Profile Description : sRGB IEC61966-2.1 Media White Point : 0.95045 1 1.08905 Media Black Point : 0 0 0 Red Matrix Column : 0.43607 0.22249 0.01392 Green Matrix Column : 0.38515 0.71687 0.09708 Blue Matrix Column : 0.14307 0.06061 0.7141 Device Mfg Desc : IEC http://www.iec.ch Device Model Desc : IEC 61966-2.1 Default RGB colour space - sRGB Viewing Cond Desc : Reference Viewing Condition in IEC61966-2.1 Viewing Cond Illuminant : 19.6445 20.3718 16.8089 Viewing Cond Surround : 3.92889 4.07439 3.36179 Viewing Cond Illuminant Type : D50 Luminance : 76.03647 80 87.12462 Measurement Observer : CIE 1931 Measurement Backing : 0 0 0 Measurement Geometry : Unknown Measurement Flare : 0.999% Measurement Illuminant : D65 Technology : Cathode Ray Tube Display Red Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Green Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Blue Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Application Record Version : 2 IPTC Digest : 460cf28926b856dab09c01a1b0a79077 X Resolution : 300 Displayed Units X : inches Y Resolution : 300 Displayed Units Y : inches Print Style : Centered Print Position : 0 0 Print Scale : 1 Global Angle : 30 Global Altitude : 30 Copyright Flag : False URL List : Slices Group Name : Num Slices : 1 Pixel Aspect Ratio : 1 Photoshop Thumbnail : (Binary data 4966 bytes, use -b option to extract) Has Real Merged Data : Yes Writer Name : Adobe Photoshop Reader Name : Adobe Photoshop CS Exif Byte Order : Big-endian (Motorola, MM) Orientation : Horizontal (normal) Resolution Unit : inches Software : Adobe Photoshop CS Macintosh Modify Date : 2007:10:10 14:06:20 Color Space : sRGB Exif Image Width : 3504 Exif Image Height : 2479 Compression : JPEG (old-style) Thumbnail Offset : 302 Thumbnail Length : 0 Page Mode : UseThumbs Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6 About : uuid:fa7fa096-7732-11dc-9e54-000a95ae8bfc Producer : Acrobat Distiller 5.0.5 for Macintosh Create Date : 2004:02:03 16:38:43Z Metadata Date : 2007:10:10 14:16:13+01:00 Document ID : uuid:a0f0a6a4-7731-11dc-a21b-000a95ae8bfc Format : application/pdfEXIF Metadata provided by EXIF.tools