Ashly Protea Dsp Option Card Dsp1 Users Manual PE User Guide1 2

dsp1 c1bad6d6-799c-4786-afa9-df0064ef1271 Ashly Stereo Amplifier DSP1 User Guide |

: Ashly Ashly-Protea-Dsp-Option-Card-Dsp1-Users-Manual-498607 ashly-protea-dsp-option-card-dsp1-users-manual-498607 ashly pdf

Open the PDF directly: View PDF .
Page Count: 2

Download
Open PDF In Browser	View PDF

Preset, Remote & Standby Wiring

Specifications
Latency
A/D, D/A Converters:
DSP
Digital Input Type
Signal Flow Architecture

Optional Proteane DSP Input Card
Analog - 1.512 ms at 48KHz sampling.
Digital - 0.784 ms at 96KHz sampling.
24-bit
32-bit, floating-point
AES/EBU 24 bit 44.1 to 96KHz
"Click and hot plug" flexible architecture, noncompiling

PE-Series Amplifiers
Proteane DSP Option Cards
Installation and User Guide

Available Processing Blocks
Equalization
Signal Delay
HPF/LPF
Compressor/Limiter, Gate, Meter
Signal Generator
Level Control

Parametric, Notch, Graphic, Shelving, HPF/LPF, All
pass, Bandpass
Up to 967msec any input/output
Up to 8th order (48 dB/octave)
Pink noise, White Noise, Sine Wave
With or without DVCA subgrouping

Ashly Audio Inc.
847 Holt Road, Webster, NY 14580-9103
Toll Free (800) 828-6308, Tel (585) 872-0010, FAX (585) 872-0739
www.ashly.com

All Trademarks referred to herein, are the property of their respective owners.

Copyright© 2006 – Ashly Audio Inc. All Rights Reserved
Rev 1.2 1007

PE DSP

Panel Details

The Proteane-DSP cards are only for use in Ashly PE-Series (Protea
Enabled) amplifiers. The DSP-1 and DSP-2 cards offer a wide range
of digital features that extend the functionality of your PE-Series
amplifier.

Installation
If the Proteane-DSP Option Card was ordered with your amplifier, no
installation is necessary. If you are retrofitting it to a PE-Series
amplifier that you own already, follow these steps:
1. Disconnect the amplifier mains as well as all inputs and
outputs
2. Remove the 4 screws on the Standard Input card
3. Carefully pull the Standard Input card from the chassis
4. Remove the internal connectors from the Standard Input card
5. Reconnect the internal connectors to the Proteane-DSP Option
Card
6. Carefully slide the new card into the chassis
7. Replace the screws, inputs, outputs and mains
You can now power-up your amplifier and use your new card. If you
are not comfortable performing this installation, refer this task to an
authorized Ashly service provider.
The Proteane software is on the CD shipped with your amplifier. Check
www.ashly.com for software and firmware updates.

Features
Both Proteane-DSP Option Cards offer the same features, with different
connectors. The cards provide both AES/EBU digital inputs as well as
standard analog inputs.
Internal digital processing setup is accomplished via Ashly Proteane
software connected through the 10/100 Ethernet connector. To
maximize your investment in a Proteane-DSP Option Card, two
additional “processed” output connectors are provided to drive
additional amplifier channels.

1.
2.
3.
4.

5.

Balanced Inputs – On the DSP-1, these inputs are standard female XLR connectors.
On the DSP-2 these inputs are via 3-pin Euroblock grounded connectors.
Processed Channel Outputs – These connectors provide processed signal to additional
amplifiers via male XLR connectors (DSP-1) or Euroblock connectors (DSP-2).
Ethernet Connector & Indicators – The 10/100 Ethernet connector interfaces with a
Protea NE network, or computer if available. The indicators show network link and data
activity. All DSP control is via this interface and Protea software on a connected PC.
Preset Recall, Remote Standby & Remote Level Control Connector – This
connector facilitates hard-wired preset recall (as set in in Protea software), remote
standby and remote attenuation control. See wiring diagram on the next page for
connection and contact closure information
AES/EBU Input Connector – This connector accepts a standard AES/EBU digital
signal at 44.1 to 96 KHz



---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 2
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:5fcd1f5c-36ba-4982-afc7-abe5e748c012
Producer                        : Acrobat Distiller 7.0.5 for Macintosh
Create Date                     : 2007:10:24 06:22:37-04:00
Modify Date                     : 2008:04:02 09:04:13-05:00
Creator Tool                    : Word: cgpdftops CUPS filter
Metadata Date                   : 2008:04:02 09:04:13-05:00
Document ID                     : uuid:532c6da8-821b-11dc-afc1-000393bb0d92
Instance ID                     : uuid:532c7c2d-821b-11dc-afc1-000393bb0d92
Format                          : application/pdf
Creator                         : Steve Nazarian
Title                           : Microsoft Word - PE DSP User Guide1-2.doc
Author                          : Steve Nazarian

EXIF Metadata provided by EXIF.tools