Asian Express 2930-T Controller of Atom 1 Micro Drone User Manual Print
Asian Express Holding Ltd Controller of Atom 1 Micro Drone Print
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2638027 |
| Application ID | CJmMNQfQP3I7/Qd8/DqxcQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 263.3kB (3291288 bits) |
| Date Submitted | 2015-06-05 00:00:00 |
| Date Available | 2015-06-05 00:00:00 |
| Creation Date | 2015-05-20 15:10:43 |
| Document Lastmod | 2015-05-20 15:13:44 |
| Document Title | |
| Document Creator | Adobe Illustrator CS3 |
Propel Atom-1.0 Mini Drone Trim size 4.5 x 6.875 in. Spread size 9 x 6.875 in. RECOGNIZING THE FRONT & BACK OF THE Atom 1.0™ Even though the Atom 1.0™ has four rotors there is still a front or "forward" facing direction and "back" or backwards facing direction. The forward Front and forward facing direction of the Atom 1.0™ is the side with two gray propellers (see diagram E ). The rear and back of the Quadrocopter is the side with two black propellers (see diagram E). NOTE: The front of the Quadrocopter displays RED LED lights and the back of the Quadrocopter displays BLUE LED lights. Atom 1.0™ DRONE FCC Part 15 B Notice CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or experienced radio/TV technician for help. 2.4GHz Quadrocopter FRONT UNDERSTANDING TRIM ADJUSTMENTS Forward/Backward Trim • If your Atom1.0 is drifting forwards or backwards, you may need to adjust the FORWARD/BACKWARD TRIM button (see diagram J). • If your Atom1.0 drifts forward, push and release the BACKWARD TRIM button back repeatedly until the motion stops and proper flight is maintained. • If your Atom 1.0™ drifts backwards, push and release the FORWARD TRIM button forward in the same manner until the problem is resolved. • From time to time you may have to adjust the FORWARD or BACKWARD TRIM buttons to ensure the Atom 1.0™ will hover in mid-air and respond accurately to your commands. REAR 4 CHANNEL FLIGHT CONTROL Below is a list of basic flight functions for your long-range remote control Atom 1.0™™. While learning to fly your Atom 1.0™ it is best to start with a large space until you get used to the basic controls. As you master flying your Atom 1.0™ you can move to more advanced maneuvering techniques. Practice makes perfect! When you have these basic steps down you can move to the next level. Move the left Throttle stick up to increase the speed and the Atom 1.0™ will accelerate and ascend. Move the left Throttle stick down to decrease the speed and the Atom 1.0™ will decelerate and descend (see diagram F). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Right/Left Trim • If your Atom1.0 is drifting leftt or right, you may need to adjust the LEFT/RIGHT TRIM button (see diagram K). • If your Atom1.0 drifts left, push and release the RIGHT TRIM button back repeatedly until the motion stops and proper flight is maintained. • If your Atom 1.0™ drifts right, push and release the LEFT TRIM button in the same manner until the problem is resolved. • From time to time you may have to adjust the LEFT or RIGHT TRIM buttons to ensure the Atom 1.0™ will hover in mid-air and respond accurately to your commands. Move the left Throttle stick left and the Atom 1.0™ will rotate left. Move the left Throttle stick right and the Atom 1.0™ will rotate right (see diagram G). LEVEL SURFACE CALIBRATION INSTRUCTION BOOKLET Move the right Direction Stick up and the Atom 1.0™ will move forward. Move the right Direction Control down and the Atom 1.0™ will move backward (see diagram H). WARNING: Never leave product charging unattended for extended periods of time. Always disconnect HD Sonic Drone from charger immediately after the HD Sonic Drone is fully charged. Please refer to enclosed safety instructions. PACKAGE CONTAINS: WARNING! CHOKING HAZARD - Small parts. Not suitable for children under 3 years. Conforms to safety requirements of ASTM, CPSIA and FCC. HD Sonic Drone ©2015 Rooftop Brands™ All rights reserved Tel: + (1) 949-566-9573 • www.propelrc.com 2.4G Wireless Controller Made in China TABLE OF CONTENTS Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Remote Control Battery Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Charging Your Atom 1.0™ Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Atom 1.0™ Quadcopter Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Remote Control Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Flight Preperation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Synching Your Atom 1.0™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Flying Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recognizing The Front & Back Of The Atom 1.0™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Channel Flight Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Understanding Trim Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Level Surface Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Low Battery Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Switching The Flight Lever To The Left Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Switching To High Speed Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Performing A 360º Stunt Roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Casting Off From Your Palm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Replacing The Propeller Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Battery Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Spare Parts USB charging cord Instruction Manual Colors and styles may slightly vary. • 4 channel flight controls allow for incredible maneuverability including360º arial stunts! • built-in 6axis gyro chip for extremely stable flight and maneuverability. • digital radio allows flight range up to 20 meters. REMOTE CONTROL BATTERY INSTALLATION LOW BATTERY WARNING If the power indicator LED on the remote lights up and emits an alert sound it means you are running at low voltage and need to land the aircraft slowly and safely and replace the batteries. If the LED lights on the Atom 1.0™ begin flashing it means you are running at low voltage and you need to land the aircraft slowly and safely and recharge the aircraft. WARNING: Do not attempt a 360º flip when you are given a low voltage warning SWITCHING THE FLIGHT LEVER TO THE LEFT CONTROL PERFORMING A 360º STUNT ROLL To change the controls to the opposite sides: 1. Turn on the aircraft . 2. Press the control lever on the left side straight down while switching on the remote (see digram M). 3. To switch the controls back. switch tthe remote off and back on. Once the Atom 1.0™ is airborne, 1. Press the right control lever straight down. 2. Move the lever in the direction you wish to perform the 360º roll (see diagram Q). Push Down Unscrew the battery cover from the back of the controller as shown in diagram A. Install 2 “AAA” alkaline batteries into the controller as shown in diagram B. Replace the battery cover. Turn over the controller and turn the on/off switch to the on position the red LED will flash if batteries are installed correctly. FEATURES 1. 2. 3. 4. Move the right Direction Control left and the Atom 1.0™ will bank to the left. Move the right Direction Control right and the Atom 1.0™ will bank to the right (see diagram I). If the aircraft becomes unstable during the course of flying, you may need to restabilize the internal gyros. To do this place the Atom 1.0™ on a level surface and pull both of the control levers on the remote down and to the left (approximately 45º) at the same time. The LEDs on the Atom 1.0™ will flash quickly and then remain solid, this indicates your aircraft has been stabilized (see diagran L). Switch On 4. Move the left throttle left/right to fly the aircraft left/right (see digram N). 5. Move the right throttle left/right to rotate the aircraft left/right (see digram O). CHARGING YOUR Atom 1.0™ BATTERY 1. Switch the quadcopter off and connect the power cable to the unit making sure the arrow side of the connector is on top side facing the top of the Atom 1.0™ (see diagrams C1 and C2). CAUTION: improper connection will damage the Atom 1.0™. 2. Connect the USB end of the cable to your computers USB port (see diagram D). 3. Average charging time is 25 minutes, the USB indicator light will glow red while the unit is charging. Remove promptly after the red LED turns off, the charge is now complete. A full charge will allow for about 5 minutes of flight time depending on environment and user input. C1 C2 SWITCHING TO HIGH SPEED MODE To change the throttle speed from the default low speed to high speed: 1. Turn on the remote. 2. Press the control lever on the left side straight down to switch modes (see digram P). 3. To switch back to low speed press the left control lever down again. 4. Speed mode returns to low speed once the remote is turned off. CASTING OFF FROM YOUR PALM Place the Atom 1.0™ on your palm and gently toss it into the air as you engage the throttle. CAUTION: Be careful not to touch the blades to aviod injury. Arrow Mark Thank you for purchasing the Atom 1.0™ 2.4 Ghz Mini Quadrocopter. Please read this instruction booklet as it contains valuable information on how to properly fly and care for your Atom 1.0™ Drone. IMPORTANT: ALWAYS REMEMBER TO UNPLUG YOUR CHARGING CORD WHEN NOT IN USE! Atom 1.0™ QUADCOPTER DIAGRAM TROUBLESHOOTING YOUR ATOM1.0™ WARNING DO NOT FLY YOUR Atom 1.0™ IN FOUL WEATHER! Rear Rotar Blades (Black) Charging Socket ATOM 1.0™ WARNING: PROBLEM POSSIBLE REASON SOLUTION NO POWER 1. Power switched off 2. Polarity is reversed 1. Switch the ON/OFF switch to ON 2. Make sure all batteries are installed correctly (see diagram B) 3. Replace batteries 3. Batteries may be dead FLIGHT PREPARATION Landing Gear Charging Socket Front Rotor Blades (Light Gray) • Verify that there are 2 “AAA” batteries inside the remote control unit and the Atom 1.0™ has been fully charged. • Make sure your Atom 1.0™ and controller are both turned on. • Make sure to be in a large space with an open radius of at least 50 feet. • Make sure the empty space has no obstacles and river. Set your Atom 1.0™ on a clean flat surface before take-off. DO NOT ATTEMPT TO FLY YOUR Atom 1.0™ IF THERE IS RAIN, SNOW, HEAVY WINDS, THUNDER OR LIGHTNING OUTDOORS. IT COULD DAMAGE YOUR PRODUCT AND POSSIBLY EVEN CAUSE BODILY HARM. SYNCING YOUR Atom 1.0™ On/Off Switch Atom 1.0™ REMOTE DIAGRAM Forward Trim Backward Trim Throttle Control Direction Control Power Indicator Light Important! When syncing your ATOM1.0 quadrocopter with the controller always make sure that the quadrocopter is on a flat level surface and that your digital trim settings are in the center position. This insures that the 6 Axis gyro is properly programmed to mimic your trim settings. Your Atom 1.0™ utilizes an automatic 2.4G channel selection system that allows up to 8 people to fly side by side in the same wireless range with no interference. For One Person Play: 1. Before starting, make sure that the power on both your controller and Atom 1.0™ are in the OFF position. Make sure that there are no other 2.4G devices in the area as well. 2. Turn ON the Atom 1.0™ and set it down on a flat surface. The LED indicator lights of the Atom 1.0™ should begin to flash. 3. Turn ON the remote, you will hear long beep, the Atom 1.0™’s red LED lights should change to solid, push the throttle on the left all the way forward and then pull the throttle all the way back. Your controller and the helicopter should now be successfully synced , if not, repeat above steps again. For Multi Person Play: 4. Before starting, make sure that the power on all Atom 1.0™ Drones and Controllers are in the OFF position. Make sure that there are no other 2.4G devices in the area as well. 5. Each person will have to sync their Atom 1.0™ individually at a different time to avoid interference. Follow steps 1 to 3 above making sure to keep away from other people while also making sure that no one else is syncing at the same time. 6. After syncing a player’s Atom 1.0™, it should be left ON until all players have synced their Atom 1.0™ Drone quadrocopters. 7. Should there be a mistake or interference, all players must turn off their controllers and Atom 1.0™ Drone Quadrocopters for 60 seconds and then begin the process again. Left Trim Right Trim Aircraft Won’t lift off 1. Rotor speed too slow 2. Aircraft not fully charged 1. Push throttle lever forward 2. Recharge your Atom 1.0™ Aircraft Decsends Too Fast 1. Moving the throttle too quickly 1. Control the throttle slower and smoother 1. Gyroscopes not functioning 1. Turn of the Atom 1.0™ and Reset the Gyros (see diagram L) 1. Aircraft is out of range of remote 1. Keep the aircraft within a 20 meter radius of the remote Aircraft Not Responding Loss of Atom 1.0™ Control 1. Remote is switched off 2. Atom 1.0™ is switched off 3. Too windy REPLACING THE PROPELLER BLADES Your Atom 1.0™ propeller system is a precision instrument that may need repair or replacement from time to time for optimal flight function. Crash landing from high-speed aerial flights may cause damage to your Atom 1.0™ propellers. 1. Atom 1.0™ have four blades, two gray propellers on the front, and two black propellers on theback Please note that the blades and the Atom 1.0™ are labeled with an embossed L or R (see the diagram S). 2. When replacing the propeller blades, gently remove the blade from the rotor shaft. Make sure to match both the color of the blade and the indication letter on the blade with the letter on the aircraft. 3. Replace the damaged blade with the correct blade as shown in diagram Q. FLYING TIPS Power On/Off Switch 4. The Remote light is flashing 1. Switch the ON/OFF switch to ON 2. Switch the ON/OFF switch to ON 3. Windy conditions severly impare the operation of the Atom 1.0 4. Replace batteries Remote Not Respnding Diagram S • It is recommended that you operate the Atom 1.0™ in a wide space. The ideal space should have a 200 foot radius. • Parental guidance or adult supervision is suggested at all times. • If you are flying the Atom 1.0™ with others, make sure all spectators are behind you. • For best performance, it is recommended that you operate the Atom 1.0™ in zero wind conditions. Wind can greatly affect the performance of the aircraft. The Atom™ is designed for INDOOR or OUTDOOR. Atom™ blades revolve at high speeds and can cause damage to the user, spectators and animals. Stand away from the Atom 1.0™ to reduce the risk of getting into the flight path. Warn spectators that you will be flying your Atom 1.0™ so that they are aware of its position. Before flight, inspect the rotor blades to make certain that the blades are securely fastened to the Atom 1.0™. WARNING! • Choking/Cutting Hazard. Small Parts/Sharp Rotor Blades. • Keep hands, hair and loose clothing away from the propeller when the power switch is turned to the ON position. • Turn off the transmitter and Atom™ power switches when not in use. • The included charger is built specifically for the Atom™ Li-Poly battery. Do not use it to charge any other battery. • New alkaline batteries are recommended for maximum performance. • Parental supervision recommended when flying Atom™. BATTERY WARNINGS RECHARGEABLE BATTERY: This Atom™ uses a Li-Poly rechargeable battery. If battery no longer stays charged, dispose of battery properly according to local disposal requirements. CONTROLLER BATTERIES: Remote control requires 2 “AAA” batteries (not included). Please read the important battery safety warning below. • Do not mix alkaline, standard (carbon-zinc) and rechargeable batteries (Nickel Metal Hydride). • Do not mix old and new batteries. • Non-rechargeable batteries are not to be recharged. • Rechargeable batteries are to be removed from the item before being charged (if removable). • Rechargeable batteries are only to be charged under adult supervision. • Exhausted batteries should be removed immediately and must be recycled or disposed of properly according to state or local government ordinances and regulations. • The supply terminals are not to be short-circuited. • Only batteries of the same or equivalent type as recommended are to be used. • Batteries are to be inserted with the correct polarity (see inside booklet for diagram). • Do not dispose batteries in a fire - batteries may leak or explode. CARE AND MAINTENANCE • Always remove the batteries from the wireless infrared remote control when it is not being used for an extended period of time. • To clean, gently wipe the remote control and Atom™ with a clean damp cloth. • Keep the toy away from direct heat or sunlight. • Do not submerge the toy into water. This can damage the unit beyond repair. • Parental guidance recommended when installing or replacing the batteries. FRONT Gray Blade Front Left = L Gray Blade Front Right = R Black Blade Back Left = L Black Blade Back Right = R REAR 10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 4.1-c036 46.277092, Fri Feb 23 2007 14:16:18 Format : application/pdf Title : Print Creator Tool : Adobe Illustrator CS3 Create Date : 2015:05:20 15:10:43-07:00 Modify Date : 2015:05:20 15:13:44-07:00 Metadata Date : 2015:05:20 15:13:44-07:00 Thumbnail Width : 152 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 12457 bytes, use -b option to extract) Document ID : uuid:8496696F7600E511B358F239B98F08B1 Instance ID : uuid:14804ec3-4edf-0340-b988-34aedc45879e Derived From Instance ID : uuid:8396696F7600E511B358F239B98F08B1 Derived From Document ID : uuid:A5B423B4A5FCE41190FF9E3451A5063A Startup Profile : Print N Pages : 1 Has Visible Transparency : True Has Visible Overprint : False Max Page Size W : 24.000000 Max Page Size H : 38.000000 Max Page Size Unit : Inches Font Name : HelveticaNeue-Condensed, GothamRounded-Light, HelveticaNeue-BoldCond, GothamRounded-Book, Arial-BoldMT, Univers-Condensed, Swiss721BT-Roman, MyriadPro-Regular, MyriadMM Font Family : Helvetica Neue, Gotham Rounded, Helvetica Neue, Gotham Rounded, Arial, Univers, Swiss 721 BT, Myriad Pro, Myriad MM Font Face : 57 Condensed, Light, 77 Bold Condensed, Book, Bold, 57 Condensed, Roman, Regular, Regular Font Type : Type 1, Open Type, Type 1, Open Type, Open Type, Type 1, Type 1, Open Type, Multiple Master Font Version : 001.000, Version 1.200, 001.000, Version 1.200, Version 5.01.2x, 001.003, 2.0-1.0, Version 2.007;PS 002.000;Core 1.0.38;makeotf.lib1.7.9032, 001.001 Font Composite : False, False, False, False, False, False, False, False, False Font File Name : HelveNeuCon; HelveticaNeue Condensed, GothamRnd-Light.otf, HelveNeuBolCon; HelveticaNeue BoldCond, GothamRnd-Book.otf, Arial Bold.ttf, UniveCon; C Univers 57 Condensed, SwissBTRom; Swis721 BT, MyriadPro-Regular.otf, MyriaMM; Myria Plate Names : Cyan, Magenta, Yellow, Black Swatch Groups Colorants Tint : 100.000000 Swatch Groups Colorants Cyan : 80.000000 Swatch Groups Colorants Magenta : 5.000001 Swatch Groups Colorants Yellow : 10.000002 Swatch Groups Colorants Black : 0.000000 Swatch Groups Group Name : Grayscale Swatch Groups Group Type : 1 Swatch Groups Colorants Swatch Name: K=5 Swatch Groups Colorants Mode : GRAY Swatch Groups Colorants Type : PROCESS Swatch Groups Colorants Gray : 12 Page Count : 1 Creator : Adobe Illustrator CS3EXIF Metadata provided by EXIF.tools