Asian Express BKST003R Micro Video Drone User Manual

Asian Express Holdings Limited Micro Video Drone

User manual

317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk FLIGHTFORCE™MICRO VIDEO DRONE For ages 14+
TABLE OF CONTENTSWarnings and Cautions.................................2FCC Information ......................................12Location of Parts and Controls.........................14Controller Battery Installation ..........................16Charging the Micro Video Drone Battery ...............17Syncing the Micro Video Drone . . . . . . . . . . . . . . . . . . . . . . . . 19Preparing for Flight ...................................21Flying Tips............................................22Recognizing the Front and Rear of the Micro Video Drone . .23Flight Controls ........................................24Speed Selection ......................................28Understanding Trim Adjustments  ......................29Performing a 360º Stunt Roll ..........................32Level Surface Gyro Calibration.........................33 Low Battery Warning..................................34317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk 1Using the On-Board Camera and Video Recorder.......35Replacing The Propeller Blades........................39Troubleshooting .......................................40Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Micro Video Drone Specifications ......................43Warranty  .............................................44
2317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk CAUTION •   TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER.  THERE ARE NO SERVICEABLE PARTS INSIDE.  •   TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,  DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.The lightning flash with arrow-head symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the unit’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit.3IMPORTANT SAFETY INSTRUCTIONSAll of the safety and operating instructions should be read, adhered to and followed before the unit is operated.SAVE THESE INSTRUCTIONS
4317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk MICRO VIDEO DRONE WARNINGS:1.  The Micro Video Drone is designed for INDOOR or      OUTDOOR flight.  2.  The Micro Video Drone’s blades revolve at high speeds    and can cause damage to the user, spectators and animals.    Stand away from the Micro Video Drone to reduce the   risk of getting into the flight path and always maintain     visual contact with the Micro Video Drone while flying. 3.  Warn spectators that you will be flying your Micro Video    Drone so that they are aware of its position. 4.  Before flight, inspect the rotor blades to make certain     that the blades are securely fastened to the Micro Video    Drone. 5.  Before flying, check your local laws and regulations      pertaining to drone usage. 6.  It is recommended to operate the Micro Video Drone in a    wide open space. The ideal space should have a  200-foot    radius.  7.  Parental guidance or adult supervision is suggested at    all times. 8.  If you are flying the Micro Video Drone with others, make    sure all spectators are behind you. 9.  For best performance, it is recommended that you      operate the Micro Video Drone in zero wind conditions,    as wind can greatly affect the performance of the aircraft.10.  Record responsibly. Respect the privacy of individuals      when recording video or taking photos with the Micro      Video Drone. 11.  Obtain permission from individuals before circulating      videos or photos taken with the Micro Video Drone.  CAUTION: DO NOT ATTEMPT TO FLY THE MICRO VIDEO DRONE IF THERE IS RAIN, SNOW, HEAVY WINDS, THUNDER OR LIGHTNING OUTDOORS. IT COULD DAMAGE YOUR PRODUCT AND MAY CAUSE BODILY HARM.5DO NOT FLY THE DRONE IN FOUL WEATHER!WARNING
WARNING!•  Choking/Cutting Hazard. Small Parts/Sharp Rotor Blades.•  Keep hands, hair and loose clothing away from the propel-   ler when the power switch is turned to the ON position.•  Turn off the controller and Micro Video Drone power      switches when not in use.•  Not suitable for children under 14 years old. Parental    supervision recommended when flying the Micro Video      Drone.6317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk 7BCBATTERY WARNINGSRECHARGEABLE BATTERY (Micro Video Drone): This device contains a non-removable Lithium-Polymer battery. The included charger is built specifically for the Micro Video Drone Li-Poly battery. Do not use it to charge any other battery. The battery must be recycled or disposed of properly. Contact your local waste management office for information on battery recycling or disposal.  CONTROLLER BATTERIES:•  New alkaline batteries are recommended for maximum    performance.•  Do not mix alkaline, standard (carbon-zinc) and recharge-   able batteries (Nickel Metal Hydride).•  Do not mix old and new batteries.•  Non-rechargeable batteries are not to be recharged.
8317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk •  Rechargeable batteries are to be removed from the item    before being charged (if removable).•  Rechargeable batteries are only to be charged under adult    supervision.•  Exhausted batteries should be removed immediately and    must be recycled or disposed of properly according to      state or local government ordinances and regulations.•  The supply terminals are not to be short-circuited.•  Only batteries of the same or equivalent type as    recommended are to be used.•  Batteries are to be inserted with the correct polarity.•  Do not dispose batteries in a fire - batteries may leak or    explode. 9DANGERTo reduce the risk of electric shock, burns, fire or injury:1.  Do not use while bathing or in a shower.2.   Do not place or store unit where it can fall or be pulled  into a tub or sink.3.   Do not place in, drop or submerge in water or  other liquid.4.   Do not reach for a unit that has fallen into water.  Unplug it immediately.5.   Care should be taken so that objects do not fall and  liquids are not spilled onto the unit.
10317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk WARNING1.   Close supervision is necessary when this appliance/product is used by or near children or mentally disabled individuals.2.   Use this unit only for its intended use as described in  this manual.3.   Unplug this unit during lightning storms or when unused  for long periods of time.4.  Never drop or insert an object into any opening.5.   Protect the power cord from being walked on or pinched, particularly at plug outlets, convenience receptacles and the point where it exits the unit.6.   Do not allow cord to touch hot surfaces. Wrap cord loosely around the unit when storing.7.   The unit should be situated away from direct sunlight or heat sources such as radiators, electric heaters, heat registers, stoves, or other units (including amplifiers) that produce heat. Avoid placing on top of stereo equipment that radiates heat.8.   Never block the air openings of the unit with materials such 11as clothing, plastic bags or papers, or place it on a soft surface such as a bed or couch, where the air openings may be blocked.9.   Do not overload the electrical outlet. Use only the power source as indicated.10.  Do not carry this unit by its cord or use the cord  as a handle.11.  Never operate this unit if it has a damaged cord or plug, if it is not working properly, or if it has been dropped or damaged, or dropped into water. If the unit’s power supply cord or plug is damaged, do not attempt to fix it yourself.12.  To avoid the risk of electric shock, do not disassemble or attempt to repair the unit. Incorrect repair can cause risk of electric shock or injury to persons when the unit is used.13.  Do not operate in the presence of explosive and/or flammable fumes.14.  Never remove the plug from the outlet by pulling the  power cord.
12317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk FCC INFORMATIONCaution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:•  Reorient or relocate the receiving antenna.•  Increase the distance between the equipment and receiver.13•   Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.•   Consult the dealer or an experienced radio/TV technician for help.This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This equipment may not cause harmful interference.2.  This equipment must accept any interference received, including interference that may cause undesired operation.Modifications not authorized by the manufacturer may void the user’s authority to operate this device.
14317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk LOCATION OF PARTS AND CONTROLS1.  Front Rotor Blades (2)2.  Front LED Indicator (2)3.  Camera4.  Rear LED Indicator (2)5.  Rear Rotor Blades (2)6.  microSD Card Slot7.  On/Off Switch8.  USB Charging Port  78ONOFF213546159.  Speed Button10.  Throttle Control Stick11.  Rotate Left Trim Button12.  Rotate Right Trim Button13.  Forward Trim Button14.  Backward Trim Button15.  On/Off Switch16.  Left Trim Button17.  Right Trim Button18.  Direction Control Stick 19.  Camera Button20.  Power LED IndicatorLOCATION OF PARTS AND CONTROLS10911131415161718192012
16317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk CONTROLLER BATTERY INSTALLATION1.  Unscrew the battery cover from the back of the      controller as shown in figure A.2.  Install 2 AAA alkaline batteries (not included) into the     controller as shown in figure B.3.  Replace the battery cover.4.  Turn over the controller and turn the ON/OFF SWITCH    to the ON position. The POWER LED INDICATOR will     flash red to indicate the batteries  are installed correctly.            Fig. A Fig. B17CHARGING THE MICRO VIDEO DRONE BATTERY1.  Switch the Micro Video Drone OFF. Insert the included    USB cable into the USB CHARGING PORT as shown in    figure C.    Note: The USB plug fits into the USB CHARGING PORT in one way only. Do not force it. Improper connection will damage the Micro Video Drone.             Fig. C
18317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk 2.  Connect the USB end of the cable to your computer’s     USB port as shown in figure D.            3.  The red LED on the USB plug turns on when charging is    complete. Average charging time is 40 minutes.Note: The red LED on the USB plug turns on when connected to a power source. When the USB plug is connected to the Micro Video Drone, the red LED will turn off. When the Micro Video Drone is fully charged the red LED will turn on. A full charge will allow for about 5-6 minutes of flight time. Unplug the charging cord when not in use.Fig. DONOFF19SYNCING THE MICRO VIDEO DRONEImportant! When syncing the Micro Video Drone with the controller, always make sure that the Micro Video Drone is on a flat level surface and that your digital trim settings are in the center position. This ensures that the 6-axis gyro is properly programmed to mimic your trim settings. The Micro Video Drone utilizes an automatic 2.4Ghz channel selection system that allows up to 8 people to fly side by side in the same wireless range with no interference.FOR ONE-PERSON PLAY1.  Before starting, make sure that the power switches on    both the controller and the Micro Video Drone are in the    OFF position. Make sure that there are no other 2.4Ghz    devices in the area.2.  Turn the Micro Video Drone ON and set it down on a flat    surface. The FRONT AND REAR LED INDICATORS will    begin to flash rapidly.3.  Turn the controller ON, one beep will sound. The      FRONT AND REAR LED INDICATORS will flash slowly.
20317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk 4.  Push the THROTTLE CONTROL STICK all the way   forward (one beep will sound) and then pull the  THROTTLE CONTROL STICK all the way back. A   second beep will sound and the FRONT AND REAR      LED INDICATORS will be solid, indicating the controller    and the Micro Video Drone are successfully synced.  If not,    repeat above steps.FOR MULTI-PERSON PLAY5.  Before starting, make sure that the power switches on    both the controller and the Micro Video Drone are in the OFF    position. Make sure that there are no other 2.4G devices    in the area.6.  Each person needs to sync their Micro Video Drone at a    different time to avoid interference. Follow steps 1 to 4    above ensuring that no one else is syncing at the same time. 7.  After syncing, each player’s Micro Video Drone should be left    ON until all players have synced their Micro Video Drones. 8.  Should there be interference, all players must turn off their    controllers and Micro Video Drone for up to 60 seconds and    then begin the syncing process again.  21PREPARING FOR FLIGHT 1.  Verify that there are 2 AAA batteries inside the remote    control unit and the Micro Video Drone has been  fully     charged.2.  Confirm your Micro Video Drone and controller are both    turned on.  3.  Make sure to be in a large space with an open radius of    at least 50 feet.  4.  Make sure the empty space has no obstacles or water    close by. 5.  Place the Micro Video Drone on a clean, flat surface      before takeoff. CAUTION: DO NOT ATTEMPT TO FLY THE MICRO VIDEO DRONE IF THERE IS RAIN, SNOW, HEAVY WINDS, THUNDER OR LIGHTNING OUTDOORS. IT COULD DAMAGE YOUR PRODUCT AND MAY CAUSE BODILY HARM.
22 23317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk FLYING TIPS•  It is recommended to operate the Micro Video Drone in a    wide open space. The ideal space should have a  200-foot    radius.  •  Parental guidance or adult supervision is suggested at all    times. •  If you are flying the Micro Video Drone with others, make    sure all spectators are behind you. •  For best performance, it is recommended that you operate   the Micro Video Drone in zero wind conditions, as wind can    greatly affect the performance of the aircraft.RECOGNIZING THE FRONT AND REAR OF THE MICRO VIDEO DRONE  The Micro Video Drone has a “front” and a “rear.” The front and forward-facing direction of the Micro Video Drone  is the side with the CAMERA as shown in figure E. The LED  indicators on the front of the Micro Video Drone are white. The rear and backward-facing direction of the Micro Video Drone is the side with USB CHARGING PORT as shown in figure E. The LED indicators on the rear of the Micro Video Drone are red.        RearFig. EFrontCameraUSB Charging Port
24317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk FLIGHT CONTROLS Below is a list of basic flight functions. While learning to fly the Micro Video Drone, it is best to start in a large space until you get used to the basic controls. As you master flying your Micro Video Drone, you can move to more advanced maneuvering techniques. 1.  Move the THROTTLE CONTROL STICK upward to      increase the speed of the propellers and the Micro Video    Drone will accelerate upward and ascend.    Move the THROTTLE CONTROL STICK down to      decrease the speed and the Micro Video Done will      decelerate and descend (see figure F).        Fig. F252.  While in the air, move the THROTTLE CONTROL STICK    left and the Micro Video Drone will rotate left.   Move the THROTTLE CONTROL STICK right and      the Micro Video Drone will rotate right (see figure G).                 Fig. G
26317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk 3.  While in the air, move the DIRECTION CONTROL STICK    up and the Micro Video Drone will move forward.   Move the DIRECTION CONTROL STICK down and the    Micro Video Drone will move backward (see figure H).                 Fig. H274.  While in the air, move the DIRECTION CONTROL STICK    left and the Micro Video Drone will bank to the left.   Move the DIRECTION CONTROL STICK right and the     Micro Video Drone will bank to the right (see figure I).                 Fig. I
28317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk SPEED SELECTION  The Micro Video Drone has 3 speed settings: Low, Medium and High. Low speed is the default setting. 1.  Press the SPEED BUTTON to change to Medium Speed.    Two beeps will sound. 2.  Press the SPEED BUTTON to change to High Speed.     Three beeps will sound. 3.  Press the SPEED BUTTON to change to Low Speed.     One beep will sound.  29UNDERSTANDING TRIM ADJUSTMENTS FORWARD/BACKWARD TRIM•  If the Micro Video Drone is drifting forward or backward,    the FORWARD/BACKWARD  TRIM may need to be      adjusted. •  If the Micro Video Drone drifts forward, push and release    the BACKWARD TRIM BUTTON repeatedly until the      motion stops and proper flight is maintained. •  If the Micro Video Drone drifts backward, push and release    the FORWARD TRIM BUTTON repeatedly until the motion    stops and proper flight is maintained. •  The FORWARD or BACKWARD TRIM may need to be   adjusted during use to ensure the Micro Video Drone will    hover in mid-air and respond accurately to commands.
30317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk RIGHT/LEFT TRIM•  If the Micro Video Drone is drifting left or right, the LEFT/   RIGHT TRIM may need to be adjusted. •  If the Micro Video Drone drifts left, push and release the    RIGHT TRIM BUTTON repeatedly until the motion  stops    and proper flight is maintained. •  If the Micro Video Drone drifts right, push and release the    LEFT TRIM BUTTON repeatedly until the motion  stops      and proper flight is maintained. •  The LEFT or RIGHT TRIM may need to be adjusted during   use to ensure the Micro Video Drone will hover in mid-air    and respond accurately to commands.      31ROTATE RIGHT/LEFT TRIM•  If the rotation of the Micro Video Drone is drifting left or    right, the ROTATE LEFT/ROTATE RIGHT TRIM may need    to be adjusted. •  If the rotation of Micro Video Drone drifts left, push and     release the ROTATE RIGHT TRIM BUTTON repeatedly     until the motion  stops and proper flight is maintained. •  If the rotation of Micro Video Drone drifts right, push      and release the ROTATE LEFT TRIM BUTTON repeatedly    until the motion  stops and proper flight is maintained. •  The ROTATE LEFT or ROTATE RIGHT TRIM may need to    be adjusted during use to ensure the Micro Video Drone    will hover in mid-air and respond accurately to commands.
32317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk PERFORMING A 360º STUNT ROLL1.  Once the Micro Video Drone is airborne, press the     DIRECTION CONTROL STICK straight down.2.  Move the lever in the direction you wish to perform the    360º roll as shown in figure J.   Fig. JBottom of Controller33LEVEL SURFACE GYRO CALIBRATIONIf the Micro Video Drone becomes unstable during the course of flying, or after a crash, the onboard gyro chip may need to be recalibrated.1.  Place the Micro Video Drone on a flat level surface. 2.  Sync the controller and the Micro Video Drone (see page    19 for syncing instructions). 3.  Pull the DIRECTION CONTROL STICK all the way down    and to the right (approximately 45º) and hold for a couple   of seconds. The FRONT AND REAR LED INDICATORS on    the Micro Video Drone will flash quickly.4.  Release the control stick and the FRONT AND REAR     LED INDICATORS on the Micro Video Drone will turn solid    to indicate the Micro Video Drone has been stabilized.
34317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk LOW BATTERY WARNINGCONTROLLERWhen the controller batteries are low, the POWER LED INDICATOR will turn on. Land the Micro Video Drone slowly and replace the batteries.DRONEWhen the Micro Video Drone”s battery is low, the FRONT AND REAR LED INDICATORS will flash. Land the Micro Video Drone slowly and recharge.WARNING: Do not attempt a 360º flip when the Micro Video Drone”s battery is low. 35USING THE ON-BOARD CAMERA AND VIDEO RECORDERFORMATTING YOUR microSD CARDThe included microSD card must be formatted before videos  or photos can be saved. To format the microSD card, insert the microSD CARD into the included microSD USB card reader and plug it into your computer’s USB port as shown in figure K.  An icon will appear on your computer’s desktop. Right-click on the icon and follow instructions to format your microSD card.       Fig. K
36317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk INSTALLING THE microSD CARD IN THE MICRO VIDEO DRONE1.  Place the formatted microSD card into the microSD  CARD SLOT and push gently until a “click” is heard as     shown in figure L.            2.  Ensure the Micro Video Drone is synced to the controller    (see page 19 for syncing instructions). 3. The REAR LED INDICATORS will be solid when the     microSD card is successfully installed. NOTE: The REAR LED INDICATORS will rapidly flash to indicate the microSD card is not installed correctly or there is a problem with the card.   Fig. LmicroSD card facing up37TAKING PHOTOSPress the CAMERA BUTTON to take a photo. A beep will  sound and the REAR LED INDICATORS will flash to confirm the photo has been taken. When the REAR LED INDICATORS return to solid, another photo can be taken.  RECORDING VIDEOS Press and hold the CAMERA BUTTON for 3 seconds to start recording a video. The REAR LED INDICATORS will flash constantly to indicate that a video is recording. Press the CAMERA BUTTON to stop recording. When the REAR LED INDICATORS return to solid, another video can be recorded. Note: When the microSD card is full, the REAR LED  INDICATORS will not flash when the CAMERA BUTTON is pressed to indicate there is no memory space on the card.
38317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk REMOVING THE microSD CARDTo remove the microSD card, push in gently on the back of the card until a “click” is heard. The microSD card will “pop out” slightly and is ready for removal. Gently pull the microSD card to remove.      39REPLACING THE PROPELLER BLADESThe Micro Video Drone’s propeller system is a precision instrument that may need repair or replacement for optimal flight function. Crash landing from high-speed aerial flights may cause damage to your  Micro Video Drone’s propellers.1.  The Micro Video Drone has four blades that are      labeled with an embossed A or B as shown in figure M.2.  When replacing the propeller blades (included), gently   remove the blade from the rotor shaft. 3.  Replace the damaged blade with the new blade. Make    sure to place the A or B propellers in the correct      positions as shown figure M.RearAABBFrontFront Left=AFront Right=BRear Left=BRear Right=AFig. M
40ISSUE            SOLUTIONNo power (controller)Switch the ON/OFF switch to ON. TROUBLESHOOTINGMake sure all batteries are installed          correctly (see diagram B on page 16).Replace batteries.No power  (Micro Video Drone)Recharge the Micro Video Drone.Controller not respondingSwitch the ON/OFF switch to ON on the controller.Switch the ON/OFF switch to ON on the Micro Video Drone.Conditions are too windy.Replace batteries.Micro Video Drone not respondingCalibrate gyro (see instructions on page 33).317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk 41TROUBLESHOOTING (CONTINUED)ISSUE            SOLUTIONMicro Video Drone  won’t lift offPush THROTTLE CONTROL STICK forward.Loss of Micro Video Drone controlRecharge the Micro Video Drone.Micro Video Drone descends too fastControl the THROTTLE CONTROL STICK slower and smoother.Recharge the Micro Video Drone.Keep the Micro Video Drone within 250 feet of the controller.
42CARE AND MAINTENANCE•  Always remove the batteries from the controller when it will    not be used for an  extended period of time.•  To clean, gently wipe the Micro Video Drone and controller    with a clean damp cloth.•  Parental guidance recommended when installing or replacing    the batteries.43MICRO VIDEO DRONE SPECIFICATIONS Li-Poly Rechargeable Battery.................  3.7V, 140 mAhBattery Life..................................  Approx. 5-6 minCharging Time  ...............................  Approx. 40 minRange  .............................................250 feetRadio Frequency....................................2.4 GhzWeight ......................................  3.8 oz (107.7g)Dimensions.....................  2.3 x 2.3 in (58.4 x 58.4 mm)microSD a trademark of SD-3C, LLC.© Brookstone 2016
317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk 317918_317919 Micro Video DroneSize:4”Wx4"H_Output:100%_Prints:1/1,Blk 44ONE (1) YEAR LIMITED WARRANTYBrookstone® warrants this product against defects in materials and/or workmanship under normal  use  for  a period of  ONE (1) YEAR  from  the date of purchase by the original purchaser (“Warranty Period”). If a defect arises and a valid claim is received within  the  Warranty  Period, at  its  option,  Brookstone  will  either 1)  repair the  defect at no charge, using new or refurbished replacement parts, or 2) replace the product with a  new product that  is at least  functionally equivalent to  the  original product,  or  3) provide a store credit in the amount of the purchase price of the original product.  A replacement product or part, including a user-installable part installed in accordance with  instructions  provided  by  Brookstone,  assumes  the  remaining  warranty  of  the original product. When a product or part is exchanged, any replacement item becomes your  property  and the  replaced  item  becomes  Brookstone’s  property. When a  store credit  is  given,  the  original  product  must  be  returned  to  Brookstone  and  becomes Brookstone’s property. Obtaining Service: To obtain warranty service, call Brookstone Limited Warranty Service  at 1-800-292-9819. Please be prepared to describe the product that needs service and  the  nature  of  the  problem.  A  purchase  receipt  is  required.  All  repairs  and replacements  must  be  authorized  in  advance.  Service  options,  parts  availability  and response times will vary. You are responsible for delivery and the cost of delivery  of the  product  or  any  parts  to  the  authorized  service  center  for  replacement,  per  our instructions.Limits  and  Exclusions:  Coverage  under  this  Limited  Warranty  is  limited  to  the United States  of America,  including  the District  of Columbia and  the U.S.  Territories of  Guam,  Puerto  Rico,  and  the  U.S.  Virgin  Islands.  This  Limited  Warranty  applies only  to  products  manufactured  for  Brookstone  that  can  be  identified  by  the “Brookstone” trademark, trade name, or logo affixed to them or their packaging. The Limited Warranty does  not apply to any non-Brookstone products. Manufacturers or suppliers other  than Brookstone  may provide their own warranties  to the  purchaser,  but  Brookstone,  in  so  far  as  permitted  by  law,  provides  these  products  “as  is.”  45This warranty  does  not  apply  to:  a)  damage  caused by  failure  to  follow  instructions relating  to  product’s  use  or  the  installation  of  components;  b)  damage  caused  by accident, abuse, misuse, fire, floods, earthquake or other external causes; c) damage caused by  service performed by  anyone who is  not a representative  of Brookstone; d)  accessories  used  in  conjunction  with  a  covered  product;  e)  a  product  or  part that  has  been  modified  to  alter  functionality  or  capability;  f)  items  intended  to  be periodically replaced by the purchaser during the normal life of the product including, without limitation, batteries or light bulbs; g) any product sold “as is” including, without limitation, floor demonstration  models  and  refurbished  items; or h) a  product  that  is used commercially or for a commercial purpose. BROOKSTONE SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES  RESULTING  FROM  THE  USE  OF  THIS  PRODUCT,  OR  ARISING OUT OF ANY BREACH OF THIS WARRANTY. TO THE EXTENT PERMITTED BY APPLICABLE LAW, BROOKSTONE DISCLAIMS ANY AND ALL STATUTORY OR IMPLIED  WARRANTIES,  INCLUDING,  WITHOUT  LIMITATION,  WARRANTIES OF  MERCHANTABILITY,  FITNESS  FOR  A  PARTICULAR  PURPOSE  AND WARRANTIES  AGAINST  HIDDEN  OR  LATENT  DEFECTS.  IF  BROOKSTONE CANNOT LAWFULLY DISCLAIM STATUTORY OR IMPLIED WARRANTIES, THEN TO  THE  EXTENT  PERMITTED  BY  LAW,  ALL  SUCH  WARRANTIES  SHALL  BE LIMITED IN DURATION TO THE DURATION OF THIS EXPRESS WARRANTY.Some  states  disallow  the  exclusion  or  limitation  of  incidental  or  consequential damages or how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.
317918    317919Find thousands more  great ideas onlineMerrimack, New Hampshire, USA 03054 • 800-846-3000 • Brookstone.com

Navigation menu