Asian Express HS-2400T Large Laser Force User Manual LaserForceMiniTank IM 2016813 v2 En

Asian Express Holdings Limited Large Laser Force LaserForceMiniTank IM 2016813 v2 En

UserManual.wiki >

Asian Express >

HS 2400T User Manual

User manual

USER MANUALTHIS PACKAGE CONTAINS:Colors and styles may slightly vary.WARNING: Never leave product charging unattended for extended periods of time. Always disconnect tank from charger immediately after the tank is fully charged. Please refer to enclosed safety instructions. Made in ChinaConforms to safety requirements of ASTM, CPSIA and FCC. CHOKING HAZARD - Small parts. Not suitable for children under 3 years.Instruction Manual2 TanksLASER FORCELASER FORCE™ are trademarks of Rooftop Brands. 8619 Wall street, Suite 400, Austin, TX 78754 tel: 949.566.9573 © 2016 Rooftop Brands™. All Rights Reserved. www.propelrc.com .USB charging cord2 ControllersRC Assault TanksStrategic Multi-Player Laser Battling TanksSTART/STOP CANNONAUTO RUNPOWER ON/OFFGUNSTART/STOP CANNONAUTO RUNPOWER ON/OFFGUNINDUSTRY CANADA NOTICE: CANADA ONLY.This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter dout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

3 4USING YOUR TANKPRIOR TO USE:• Verify that there are 2“AA”fresh batteries inside the remote control unit and the tank has been fully charged.1. Switch the ON/OFF switch located on the underside of the tank to the ON position.2. Switch the ON/OFF switch located on the front of the remote control to the ON position.3. Press the “Start/Stop” button on the remote control. You will hear an engine ignition sound followed by the sound of the tank idling. Now you may operate the other functions of the remote control/tank. NOTE: When using multiple Laser Force tanks, be sure to turn on 1 tank at a time by following the above steps in order to properly Sync each tank to its respective remote controller. Attempting to turn on multiple tanks at the same time will result in an improper pairing of tank to remote and signals will be crossed.4. Use the left and right joystick control arms to move the tank forward, backward, and turn left/right. To move forward, push both joystick forward. To move backward, pull both joystick backward. To turn right, push the left joystick forward and, depending on desired speed and radius of turn, pull the right joystick backward. To turn left, push the right joystick forward and, depending on desired speed and radius of turn, pull the left joystick backward.5. To turn your turret, use the Turret Left and Turret Right buttons.6. To fire your weapons:• Press the “Cannon” button on the remote control and the tank will make a Cannon firing sound.• Press the “Gun” button and the tank will make a machine gun firing sound. When the tank fires its weapons, it will recoil like a real tank!7. Autonomous Mode Press the "Auto Run" button and the tank will enter autonomous mode. The tank will automatically move and fire on its own for a short period. • Tank will exit autonomous mode when press the “Auto Run” Button again from the remote control or when turned off.TANK DIAGRAMREMOTE DIAGRAMBelow is a basic list of features and parts on the tank.TreadsRotating Turret (IR Laser Cannon)Rotating Turret (IR Laser Cannon)IR Laser receiver LED “Life Counter” (3 LED lights)IR Laser receiver Left & Right Joystickspush up to move forward push down to move backwardOn/Off SwitchLED “Life Counter” (3 LED lights)Speaker (underside of tank not shown)Treads (underside of tanknot shown)Treads (underside of tanknot shown)Left JoystickTurretLeftTurretRightPower LEDIndicatorTankStart/StopAuto RunModeRight JoystickCannonFireMachineGun Fire

5 68. MUTE/Limited Sound Effect Mode:• Power on both remote control and tank.• Hold down the Auto button continuously and press the Start/Stop button once to enter Mute Mode. • While in the Mute Mode, sounds effects that play when your tank is running are disabled. All other operations sounds of the tank will operate as normal.• To reactivate the sounds, press the Start/Stop button to stop the tank. Then, after waiting for several seconds, press the Start/Stop button to begin play in normal mode. BATTLING OTHER LASER FORCE TANKSGet ready for ground combat missions with your friends – or “enemies.” You can battle up to 11 additional foes for an amazing interactive battle experience.Note: Requires 1 or more additional Laser Force tanks.1. Make sure all battling Laser Force tanks are fully charged, individually synced and ready to play. READY, AIM, FIRE!�2. While operating your tank, aim your turret toward the front of your opponent’s tank and fire! Note: You must have a direct line of fire towards the IR Receiver located on the front of your opponent’s tank in order to register a “hit.”3. If you successfully “hit” your opponent with your Cannon, one of their LED indicator lights will go out. If firing your machine gun, you must “hit” your opponent 5 times in order to make one of their LED indicator lights go out. Note: If you “hit” your opponent less than 5 times with your machine gun and then “hit” them with your Cannon, the machine gun counter will reset to 0.• When “hit,” your tank will shutter from the “impact” and make sounds.• After being “hit” by your opponent’s Cannon, you will have 8 seconds to escape before being able to get “hit” again.• After being “hit” by your opponent’s machine gun, you will have 5 seconds to escape before being able to get “hit” again.• When “hit,” some functions of your tank may become disabled, just like a real tank. After 2 “hits,” (2 LED indicator lights go out), your turret and machine gun will become disabled and will not turn.3. THREE STRIKES YOUR OUT!� On the third direct hit, your tank will be disabled. GAME OVER! 4. After 10 seconds, the “destroyed” tank will recover (press Start/Stop button to resume) and will be ready for the next battle. Press the Start/Stop button to get back in the game. AUTONOMOUS MODEThe Laser Force tank has a built in Autonomous mode for a single player to battle against a computer-controlled “enemy.” Note: Requires 2 Laser Force tanks.To activate Autonomous Mode:1. Turn on and sync each tank to their respective remote controllers.2. Place the first tank into Autonomous mode by pressing the Auto Run button. That tank will now be operating on it’s own.3. Use your remote to dodge their Cannon and machine gun fire and try to “hit” them 3 times to win the game.CHANGING THE TREADSIf the treads become damaged, contact Propel customer service. Additional treads are available for purchase. You can replace the treads using the following steps:1. Remove the damaged tread by gently pulling the tread from the wheel stays.2. Place the new tread over the wheels, being careful not to use excessive force and damage the wheels or treads. BATTERY WARNINGS RECHARGEABLE BATTERY: This tank uses an internal Li-Ion rechargeable battery (650 mAh). If the battery can no longer be charged, dispose of the battery according to local disposal requirements.The remote control requires 2 “AA” batteries (not included). Please read the important battery safety warnings below. • Do not mix alkaline, standard (carbon-zinc) and rechargeable batteries (Nickel Metal Hydride).• Do not mix old and new batteries.�• Non-rechargeable batteries are not to be recharged.�• Rechargeable batteries are to be removed from the item before being charged (if removable).• Rechargeable batteries are only to be charged under adult supervision.• Exhausted batteries should be removed immediately and must be recycled or disposed of properly according to state or local government ordinances and regulations.• The supply terminals are not to be short-circuited.• Only batteries of the same or equivalent type as recommended are to be used.• Batteries are to be inserted with the correct polarity.• Do not dispose batteries in a fire - batteries may leak or explode.CARE AND MAINTENANCE • Always remove the batteries from the remote control when it is not being used for an extended period of time. • To clean, gently wipe the remote control and tank with a clean, slightly damp cloth.• Keep this product away from direct heat or sunlight.• Do not submerge the tank or remote into water, as this will damage the unit beyond repair.• Parental guidance recommended when installing, replacing, and charging the batteries. FCC Part 15 C Notice CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.� NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or experienced radio/TV technician for help.�This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and�(2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu