Asian Express PL1390-R Atom 1.0 Micro Drone User Manual Atom IM 0515 v3 own
Asian Express Holdings Limited Atom 1.0 Micro Drone Atom IM 0515 v3 own
Contents
- 1. User Manual-revised
- 2. User Manual
User Manual-revised
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3055420 |
| Application ID | yyqGawW+5VyNvpansABToA== |
| Document Description | User Manual-revised |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 240.89kB (3011073 bits) |
| Date Submitted | 2016-07-07 00:00:00 |
| Date Available | 2016-07-11 00:00:00 |
| Creation Date | 2016-06-20 10:59:55 |
| Producing Software | Adobe PDF library 10.01 |
| Document Lastmod | 2016-06-20 10:59:55 |
| Document Title | Atom-IM-0515-v3-own |
| Document Creator | Adobe Illustrator CS6 (Macintosh) |
Trim size 4.5 x 6.875 in. Spread size 9 x 6.875 in. FCC Part 15 C Notice CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or experienced radio/TV technician for help. ATOM 1.0™ MICRO DRONE INDOOR / OUTDOOR WIRELESS QUADROCOPTER This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INDUSTRY CANADA NOTICE: CANADA ONLY. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter dout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. INSTRUCTION BOOKLET WARNING: Never leave product charging unattended for extended periods of time. Always disconnect the Atom 1.0™ from charger immediately after it is fully charged. Please refer to enclosed safety instructions. PACKAGE CONTAINS: WARNING! CHOKING HAZARD - Small parts. Not suitable for children under 3 years. Conforms to safety requirements of ASTM, CPSIA and FCC. ©2016 Rooftop Brands™ All rights reserved Tel: + (1) 949-566-9573 • www.propelrc.com V2 Made in China Atom 1.0™ 2.4G Wireless Controller Spare Parts USB charging cord Colors and styles may slightly vary. Instruction Manual BC TABLE OF CONTENTS Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Remote Control Battery Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Charging Your Atom 1.0™ Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Atom 1.0™ Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Remote Control Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Synching Your Atom 1.0™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Flight Preperation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Flying Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Recognizing The Front & Back Of The Atom 1.0™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3/4 Channel Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Channel Flight Controls (Advanced Flying) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 Channel Flight Controls (Beginner Flying) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Switching To Medium & High Speed Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Understanding Trim Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Level Surface Gyro Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Low Battery Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Performing A 360º Stunt Roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Replacing The Propeller Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Battery Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 FEATURES • Built-in 6axis gyro chip for extremely stable flight. • 2.4 Ghz digital technology allows for flight range up to 100 feet. • 4 channel flight controls allow for incredible maneuverability including 360º aerial stunts! • Unique Switch-Blade technology allows you to operate in either 3ch or 4ch modes for beginner to advanced pilots REMOTE CONTROL BATTERY INSTALLATION 1. 2. 3. 4. Unscrew the battery cover from the back of the controller as shown in diagram A. Install 2 “AAA” alkaline batteries into the controller as shown in diagram B. Replace the battery cover. Turn over the controller and turn the on/off switch to the on position the red LED will flash if batteries are installed correctly. CHARGING YOUR ATOM 1.0™ BATTERY 1. Switch the quadrocopter Off. Connect the power cable to the unit making sure the arrow side of the connector is on top side facing the top of the Atom 1.0™ (see diagrams C1 and C2). CAUTION: The USB plug fits the charging socket only in one way. Do not force it. Improper connection will damage the Atom 1.0™. 2. Connect the USB end of the cable to your computers USB port (see diagram D). 3. The red LED on the USB plug lights up when charging is complete. Average charging time is 30 minutes. Note: If the red LED lights up, either the charging is complete or the USB plug is not properly connected. A full charge will allow for about 5 minutes of flight time depending on environment and user input. C1 C2 Arrow Mark Thank you for purchasing the Atom 1.0™ 2.4 Ghz Mini Quadrocopter. Please read this instruction booklet as it contains valuable information on how to properly fly and care for your Atom 1.0™ Drone. IMPORTANT: ALWAYS REMEMBER TO UNPLUG YOUR CHARGING CORD WHEN NOT IN USE! ATOM 1.0™ DIAGRAM WARNING Rear Rotor Blades DO NOT FLY YOUR ATOM 1.0™ IN FOUL WEATHER! Charging Socket SYNCING YOUR ATOM 1.0™ Landing Gear Charging Socket Front Rotor Blades On/Off Switch ATOM 1.0™ REMOTE DIAGRAM Forward Trim Backward Trim Throttle Control Direction Control Important! When syncing your Atom 1.0™ quadrocopter with the controller always make sure that the quadrocopter is on a flat level surface and that your digital trim settings are in the center position. This ensures that the 6 Axis gyro is properly programmed to mimic your trim settings. Your Atom 1.0™ utilizes an automatic 2.4G channel selection system that allows up to 8 people to fly side by side in the same wireless range with no interference. For One-Person Play: 1. Before starting, make sure that the power on both your controller and Atom 1.0™ are in the OFF position. Make sure that there are no other 2.4G devices in the area as well. 2. Turn ON the Atom 1.0™ and set it down on a flat surface. The LED indicator lights of the Atom 1.0™ should begin to flash rapidly. 3. Turn ON the remote, you will hear two short beeps. The Atom 1.0™’s LED lights should now flash slowly. Push the throttle on the left all the way forward(1 beep) and then pull the throttle all the way back. A 2nd beep will sound and the lights should turn to solid. This indicates your controller and the quadrocopter are successfully synced. If not, repeat above steps. For Multi Person Play: 4. Before starting, make sure that the power on all Atom 1.0™ drones and Controllers are in the OFF position. Make sure that there are no other 2.4G devices in the area. 5. Each person will have to sync their Atom 1.0™ individually at a different time to avoid interference. Follow steps 1 to 3 above making sure that no one else is syncing at the same time. 6. After syncing a player’s Atom 1.0™, it should be left ON until all players have synced their Atom 1.0™ quadrocopters. 7. Should there be a mistake or interference, all players must turn off their controllers and Atom 1.0™ quadrocopters for up to 60 seconds and then begin the process again. PREPARING FOR FLIGHT • Verify that there are 2 “AAA” batteries inside the remote control unit and the Atom 1.0™ has been fully charged. • Make sure your Atom 1.0™ and controller are both turned on. • Make sure to be in a large space with an open radius of at least 50 feet. • Make sure the empty space has no obstacles and water close by. Set your Atom 1.0™ on a clean flat surface before take-off. DO NOT ATTEMPT TO FLY YOUR ATOM 1.0™ IF THERE IS RAIN, SNOW, HEAVY WINDS, THUNDER OR LIGHTNING OUTDOORS. IT COULD DAMAGE YOUR PRODUCT AND POSSIBLY EVEN CAUSE BODILY HARM. Power Indicator Light FLYING TIPS Power On/Off Switch Left Trim Right Trim • It is recommended that you operate the Atom 1.0™ in a wide open space. The ideal space should have a 200 foot radius. • Parental guidance or adult supervision is suggested at all times. • If you are flying the Atom 1.0™ with others, make sure all spectators are behind you. • For best performance, it is recommended that you operate the Atom 1.0™ in zero wind conditions, as wind can greatly affect the performance of the aircraft. RECOGNIZING THE FRONT & BACK OF THE ATOM 1.0™ Even though the Atom 1.0™ has four rotors, there is still a “front” or forward facing direction and "back" or backwards facing direction. The front and forward facing direction of the Atom 1.0™ is the side with two gray propellers (see diagram E ). The rear and backwards facing of the Quadrocopter is the side with two black propellers (see diagram E). NOTE: The front of the Quadrocopter displays WHITE LED lights and the back of the Quadrocopter displays RED LED lights. FRONT Push Down and hold for 3 seconds 3 CHANNEL FLIGHT CONTROLS (BEGINNER FLYING) Below is a list of basic flight functions for your long-range remote control Atom 1.0™. While learning to fly your Atom 1.0™ it is best to start in a large space until you get used to the basic controls. As you master flying your Atom 1.0™ you can move to more advanced maneuvering techniques. Practice makes perfect! When you have these basic steps down you can move to the next level. Move the left Throttle stick upwards to increase the speed of the propellers and the Atom 1.0™ will accelerate upwards and ascend. Move the left Throttle stick down to decrease the speed and the Atom 1.0™ will decelerate and descend (see diagram K). REAR 3/4 CHANNEL SELECT Atom™ 1.0 allows you to control your micro drone in 3 channel mode (beginner) or 4 channel mode (advanced flying). The Atom™ 1.0 default setting is 4 Channel mode. To change to 3 Channel mode: After syncing your quadrocopter, depress and hold the control stick on the right side straight down for 3 seconds, you will hear a long beep indicating the Atom™ 1.0 is now set to 3CH mode. (see digram F). To change back to 4 Channel mode: Depress and hold the control stick on the right side straight down for 3 seconds again, you will hear a long beep indicating the Atom™ 1.0 is now set to 4CH mode. (see digram F). 4 CHANNEL FLIGHT CONTROLS (ADVANCED FLYING) Below is a list of basic flight functions for your long-range remote control Atom 1.0™. While learning to fly your Atom 1.0™ it is best to start in a large space until you get used to the basic controls. As you master flying your Atom 1.0™ you can move to more advanced maneuvering techniques. Practice makes perfect! When you have these basic steps down you can move to the next level. Move the left Throttle stick upwards to increase the speed of the propellers and the Atom 1.0™ will accelerate upwards and ascend. Move the left Throttle stick down to decrease the speed and the Atom 1.0™ will decelerate and descend (see diagram G). While in the air, move the left Throttle stick left and the Atom 1.0™ will rotate left. Move the left Throttle stick right and the Atom 1.0™ will rotate right (see diagram H). While in the air, move the right Throttle stick left and the Atom 1.0™ will rotate left. Move the left Throttle stick right and the Atom 1.0™ will rotate right (see diagram L). While in the air, move the right Direction Stick up and the Atom 1.0™ will move forward. Move the right Direction Stick down and the Atom 1.0™ will move backward (see diagram M). SWITCHING TO MEDIUM & HIGH SPEED MODE To change the Atom 1.0’s flight speed from the default (low speed) to medium and high speed flight mode: 1. Turn on the remote. 2. Depress the control lever on the left side straight down as if pressing a button to switch modes (see digram N). 3. You will hear two beeps indicating that your drone speed changed to medium speed. 4. To change to high speed mode repeat step 2. 5. Three beeps indicates a speed changed to high speed mode. 6. To switch back to low speed repeat step 2 again, you will hear one beep indicating low speed mode. 7. Speed mode returns to low speed once the remote is turned off. While in the air, move the right Direction Stick up and the Atom 1.0™ will move forward. Move the right Direction Stick down and the Atom 1.0™ will move backward (see diagram I). While in the air, move the right Direction Stick left and the Atom 1.0™ will bank to the left. Move the right Direction Stick right and the Atom 1.0 ™ will bank to the right (see diagram J). UNDERSTANDING TRIM ADJUSTMENTS Forward/Backward Trim • If your Atom 1.0™ is drifting forwards or backwards, you may need to adjust the FORWARD/BACKWARD TRIM (see diagram O). • If your Atom 1.0™ drifts forward, push and release the BACKWARD TRIM button back repeatedly until the motion stops and proper flight is maintained. • If your Atom 1.0™ drifts backwards, push and release the FORWARD TRIM button forward in the same manner until the problem is resolved. • From time to time you may have to adjust the FORWARD or BACKWARD TRIM buttons to ensure the Atom 1.0™ will hover in mid-air and respond accurately to your commands. PERFORMING A 360º STUNT ROLL Once the Atom 1.0™ is airborne, 1. Press the right control lever straight down. 2. Move the lever in the direction you wish to perform the 360º roll (see diagram R). Right/Left Trim • If your Atom 1.0™ is drifting left or right, you may need to adjust the LEFT/RIGHT TRIM button (see diagram P). • If your Atom 1.0™ drifts left, push and release the RIGHT TRIM button repeatedly until the motion stops and proper flight is maintained. • If your Atom 1.0™ drifts right, push and release the LEFT TRIM button in the same manner until the problem is resolved. • From time to time you may have to adjust the LEFT or RIGHT TRIM buttons to ensure the Atom 1.0™ will hover in mid-air and respond accurately to your commands. LEVEL SURFACE GYRO CALIBRATION If the aircraft becomes unstable during the course of flying, or after a crash, you may need to recalibrate the onboard gyro chip. To do so, place the Atom 1.0™ on a flat level surface. Start by syncing the controller with the quadrocopter. Next, pull the right control stick on the remote all the way down and to the right (approximately 45º) and hold for a couple of seconds. The LEDs on the Atom 1.0™ will flash quickly and then turn solid when released. This indicates your drone has been stabilized (see diagram Q). LOW BATTERY WARNING If the power indicator LED on the remote lights up it means you are running at low voltage and need to land the aircraft slowly and replace the batteries in the controller. If the LED lights on the quadrocopter begin flashing it means you are running at low voltage and you need to land the aircraft slowly and recharge the quadrocopter unit. WARNING: Do not attempt a 360º flip when you are given a low voltage warning TROUBLESHOOTING YOUR ATOM 1.0™ ATOM 1.0™ WARNING: PROBLEM POSSIBLE REASON SOLUTION NO POWER 1. Power switched off 2. Polarity is reversed 1. Switch the ON/OFF switch to ON 2. Make sure all batteries are installed correctly (see diagram B) 3. Replace batteries 3. Batteries may be dead 4. The Remote light is flashing 1. Switch the ON/OFF switch to ON 2. Switch the ON/OFF switch to ON 3. Windy conditions severly affect the operation of the Atom 1.0™ 4. Replace batteries Drone Won’t lift off 1. Rotor speed too slow 2. Drone not fully charged 1. Push throttle lever forward 2. Recharge your Atom 1.0™ Drone Decsends Too Fast 1. Moving the throttle too quickly 1. Control the throttle slower and smoother 1. Gyroscopes not functioning 1. Turn on the Atom 1.0™ and Reset the Gyros (see diagram L) 1. Drone is out of range of remote 1. Keep the drone within a 20 meter radius of the remote Remote Not Responding Drone Not Responding Loss of Atom 1.0™ Control 1. Remote is switched off 2. Atom 1.0™ is switched off 3. Too windy REPLACING THE PROPELLER BLADES Your Atom 1.0™ propeller system is a precision instrument that may need repair or replacement from time to time for optimal flight function. Crash landing from high-speed aerial flights may cause damage to your Atom 1.0™’s propellers. 1. Atom 1.0™ have four blades, two gray propellers on the front, and two black propellers on the back Please note that the blades and the Atom 1.0™ are labeled with an embossed A or B (see the diagram S). 2. When replacing the propeller blades, gently remove the blade from the rotor shaft. Make sure to match both the color of the blade and the indication letter on the blade with the letter on the aircraft. 3. Replace the damaged blade with the correct blade. Black Blade Back Left = B Black Blade Back Right = A RECHARGEABLE BATTERY: This Atom 1.0™ uses a Li-Poly rechargeable battery. If battery no longer stays charged, dispose of battery properly according to local disposal requirements. CONTROLLER BATTERIES: Remote control requires 2 “AAA” batteries (not included). Please read the important battery safety warning below. • Do not mix alkaline, standard (carbon-zinc) and rechargeable batteries (Nickel Metal Hydride). • Do not mix old and new batteries. • Non-rechargeable batteries are not to be recharged. • Rechargeable batteries are to be removed from the item before being charged (if removable). • Rechargeable batteries are only to be charged under adult supervision. • Exhausted batteries should be removed immediately and must be recycled or disposed of properly according to state or local government ordinances and regulations. • The supply terminals are not to be short-circuited. • Only batteries of the same or equivalent type as recommended are to be used. • Batteries are to be inserted with the correct polarity (see inside booklet for diagram). • Do not dispose batteries in a fire - batteries may leak or explode. CARE AND MAINTENANCE • Always remove the batteries from the wireless 2.4G remote control when it is not being used for an extended period of time. • To clean, gently wipe the remote control and Atom 1.0™ with a clean damp cloth. • Keep the toy away from direct heat or sunlight. • Do not submerge the toy into water. This can damage the unit beyond repair. • Parental guidance recommended when installing or replacing the batteries. BATTERY WARNINGS FRONT Gray Blade Front Left = A Gray Blade Front Right = B WARNING! • Choking/Cutting Hazard. Small Parts/Sharp Rotor Blades. • Keep hands, hair and loose clothing away from the propeller when the power switch is turned to the ON position. • Turn off the transmitter and Atom 1.0™ power switches when not in use. • The included charger is built specifically for the Atom 1.0™ Li-Poly battery. Do not use it to charge any other battery. • New alkaline batteries are recommended for maximum performance. • Parental supervision recommended when flying Atom 1.0™ Diagram S The Atom 1.0™ is designed for INDOOR or OUTDOOR flight. Atom 1.0™ ‘s blades revolve at high speeds and can cause damage to the user, spectators and animals. Stand away from the Atom 1.0™ to reduce the risk of getting into the flight path. Warn spectators that you will be flying your Atom 1.0™ so that they are aware of its position. Before flight, inspect the rotor blades to make certain that the blades are securely fastened to the Atom 1.0™. REAR 10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Format : application/pdf Title : Atom-IM-0515-v3-own Creator Tool : Adobe Illustrator CS6 (Macintosh) Create Date : 2016:06:20 10:59:55+08:00 Modify Date : 2016:06:20 10:59:55+08:00 Metadata Date : 2016:06:20 10:59:55+08:00 Thumbnail Width : 256 Thumbnail Height : 40 Thumbnail Format : JPEG Thumbnail Image : (Binary data 5005 bytes, use -b option to extract) Document ID : xmp.did:0280117407206811822AF22120C5D5BE Instance ID : uuid:f62888a8-31ce-ef42-9f77-79bd888899c7 Original Document ID : uuid:6CBC824B7901E511A85CFA77822DA72D Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:0180117407206811822AF22120C5D5BE Derived From Document ID : xmp.did:0180117407206811822AF22120C5D5BE Derived From Original Document ID: uuid:6CBC824B7901E511A85CFA77822DA72D Derived From Rendition Class : proof:pdf History Action : saved, saved History Instance ID : xmp.iid:F97F11740720681183D1A228E89D38A6, xmp.iid:0280117407206811822AF22120C5D5BE History When : 2015:05:22 22:56:12-04:00, 2016:06:20 10:59:44+08:00 History Software Agent : Adobe Illustrator CS6 (Macintosh), Adobe Illustrator CS6 (Macintosh) History Changed : /, / Manifest Link Form : EmbedByReference Manifest Reference File Path : /work file 2016/April 2016/TRU-IM/Atom 1.0 IM/atom-own-Gary.psd Startup Profile : Print N Pages : 1 Has Visible Transparency : True Has Visible Overprint : False Max Page Size W : 10.531250 Max Page Size H : 8.406250 Max Page Size Unit : Inches Font Name : Arial-BoldMT, GothamRounded-Light, GothamRounded-Book, Helvetica-Bold, HelveticaNeue-Condensed, HelveticaNeue-BoldCond, MyriadMM, MyriadPro-Regular, Swiss721BT-Roman, Univers-Condensed Font Family : Arial, Gotham Rounded, Gotham Rounded, Helvetica, Helvetica Neue, Helvetica Neue, Myriad MM, Myriad Pro, Swiss 721 BT, Univers 57 Condensed Font Face : Bold, Light, Book, Bold, 57 Condensed, Regular, Regular, Regular, Roman, Regular Font Type : Open Type, Open Type, Open Type, TrueType, Type 1, Open Type, Multiple Master, Open Type, Type 1, Open Type Font Version : Version 3.05, Version 1.200, Version 1.200, 10.0d1e1, 001.000, 001.000, 001.001, Version 2.102;PS 2.000;hotconv 1.0.67;makeotf.lib2.5.33168, 2.0-1.0, 001.001 Font Composite : False, False, False, False, False, False, False, False, False, False Font File Name : Arial, GothamRnd-Light.otf, GothamRnd-Book.otf, Helvetica.dfont, HelveNeuCon; HelveticaNeue Condensed, HelveticaNeue-BoldCond.otf; HelveticaNeue BoldCond, MyriaMM, MyriadPro-Regular.otf, SwissBTRom; Swiss721BT Roman, Univers-Condensed.otf Plate Names : Cyan, Magenta, Yellow, Black Swatch Groups Colorants Tint : 100.000000 Swatch Groups Colorants Cyan : 80.000000 Swatch Groups Colorants Magenta : 5.000001 Swatch Groups Colorants Yellow : 10.000002 Swatch Groups Colorants Black : 0.000000 Swatch Groups Group Name : Grayscale Swatch Groups Group Type : 1 Swatch Groups Colorants Swatch Name: K=5 Swatch Groups Colorants Mode : GRAY Swatch Groups Colorants Type : PROCESS Swatch Groups Colorants Gray : 12 Producer : Adobe PDF library 10.01 Page Count : 6 Creator : Adobe Illustrator CS6 (Macintosh)EXIF Metadata provided by EXIF.tools