Asian Express PL-1610T Sky Force User Manual
Asian Express Holdings Limited Sky Force
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3425269 |
| Application ID | 4b1j/GQJJrN76mJm5fg/cQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 176.04kB (2200472 bits) |
| Date Submitted | 2017-06-14 00:00:00 |
| Date Available | 2017-06-14 00:00:00 |
| Creation Date | 2017-06-13 14:18:37 |
| Producing Software | GPL Ghostscript 9.07 |
| Document Lastmod | 2017-06-13 14:18:37 |
| Document Title | user manual.pdf |
| Document Creator | PDFCreator Version 1.7.1 |
| Document Author: | cartlee |
FCC Part 15 C Notice CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or experienced radio/TV technician for help. SKY FORCE TABLE OF CONTENTS Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Remote Control Battery Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Charging the Sky Force’s Li-Poly Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Sky Force™ Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Sky Force™ Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Remote Control Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Flight Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Syncing Your Sky Force™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Now You Are Ready To Fly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Recognizing The Front & Rear of The Sky Force™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Speed Select Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Reverse Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Headless Mode Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Flight Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Flight Practice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Adjusting The Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Calibrating The Sky Force™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Interactive Battle Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 How To Perform 360º Stunt Flips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Troubleshooting Your Sky Force™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Replacing The Propeller Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Battery Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 TM 2.4Ghz Indoor / Outdoor Battling Quadrocopter This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INDUSTRY CANADA NOTICE: CANADA ONLY. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter dout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. INSTRUCTION BOOKLET FEATURES • 6 axis gyro keeps the Sky Force™ stable in all conditions. • Push button back flip stunt. • 2 speed settings for beginner to advanced quadrocopter pilots. • Laser battle game with other Sky Force™ battling drones. • On board 2.4Ghz digital spread spectrum allows up to 8 players to battle simultaneously. REMOTE CONTROL BATTERY INSTALLATION 1. Unscrew the security screw and remove the battery cover from the back of the controller. 2. Install 3 “AA” alkaline batteries into the controller as shown in diagram A. 3. Replace the battery cover and security it. 4. Switch the controller power on you will see the indicator lights up and feel a vibration if the batteries were installed properly. AM3.LR6.SIZE AA DC1.5V AM3.LR6.SIZE AA DC1.5V AM3.LR6.SIZE AA DC1.5V 3 x “AA” Batteries (not included) CHARGING THE SKY FORCE’S LI-POLY BATTERY 1. Twist the battery lock clockwise 180º to unlock the battery.Pop out the battery from the drone battery compartment (see illustration B). 2. Next, connect the USB charger to your computer’s USB port (see diagram C ). Caution: Only use this charger with a computer USB port! Do not attempt to use other USB charging devices. 3. The red LED on the charger will start flahing. Plug the battery in,the LED light will turn solid. After the battery is fully charged, The LED will turn off. (See diagram D). Note: If the red LED is off, either the charging is complete or the USB plug is not properly connected. 4. Average charging time is approximately 40 minutes. A fully charged drone can fly for approximately 5-6 minutes depending on environment and user input. Note: If plug the USB cord in without connecting battery, the red LED light will keep flashing. Li-Poly Battery 180 PACKAGE CONTAINS: WARNING! Battery Lock Made in China V 2.0 12 Sky Force™ 2.4G Wireless Controller Spare Parts USB Charger & Li-Poly Rechargeable Battery Instruction Manual Colors and styles may vary. Black Blade Back Gray Blade Front Thank you for purchasing the Sky Force™ 2.4 Ghz High-Performance Stunt Drone. Please read this instruction booklet as it contains valuable information on how to properly fly and care for your Sky Force™. DESCRIPTION MDSER DESIGNER DATE C32-Sky Force IM.ai 114 x 174MM Cassie JUN 2017/05/12 WARNING NOW YOU ARE READY TO FLY! DO NOT FLY YOUR SKY FORCE™ IN FOUL WEATHER! If you have successfully synced your Sky Force™ to your controller as explained on page 4 you are now ready to fly. Before beginning to fly your drone you should familiarize yourself with how the controls work so please carefully read and familiarize yourself with various control features explain in the next two pages. Again as a beginner pilot you should learn how to control your drone in a large open field or park on a day with zero or very light wind. Do not try to fly your Sky Force™ too high before you become a more experienced pilot. FLIGHT PREPARATION RECOGNIZING THE FRONT & REAR OF THE SKY FORCE™ • Verify that there are 3 “AA” batteries installed the remote control unit and the Sky Force™ battery has been fully charged. • Make sure to be in a large open space preferably a field or a park with an open radius of at least 200 feet. • Make sure to start your drone on a clean flat level surface before take-off. • IMPORTANT! Until you have experience in flying your Sky Force™, it is not advised to use in any rate of wind. Wait for a zero wind day or extremely light wind when learning how to fly. Even though the Sky Force™ has four rotors there is still a front or "forward" facing direction and "rear" or backwards facing direction. The forward front and forward facing direction of the Sky Force™ is the side with two gray blades (see diagram G ). The rear and backward facing direction is the side with two black propellers (see diagram G). NOTE: The front of the Quadrocopter also displays WHITE LED light and the rear of the Quadrocopter displays RED LED lights. FRONT SYNCING YOUR SKY FORCE™ Power On/Off Back (Red LED Light) Infrared Receiver Battery Lock Front (White Light) Important! When syncing your Sky Force™ with the controller always make sure that the drone is on a flat level surface and your digital trim settings are in the center positions. This insures that the 6 Axis gyro is properly programmed to respond to your trim settings. Your Sky Force™ utilizes an automatic 2.4G channel selection system that allows up to 8 people to fly side by side in the same wireless range with no interference. 1. Before starting, make sure that the power switch is off both on your controller and the Sky Force™. Make sure that there are no other 2.4G devices in the area. CONTROLLER DIAGRAM Blue Battle Indicator Power Indicator Stunt button Throttle Direction Control Low speed High speed Forward Trim Right Bank Trim Backward Trim Left Bank Trim OFF ON FLIGHT CONTROL Below is a list of basic flight functions for your long-range remote to control the Sky Force™. While learning to fly your Sky Force™ it is best to start in a large space until you get used to the basic controls. As you master flying your Sky Force™ you can move to more advanced maneuvering techniques. Practice makes perfect! Move the Throttle stick up to increase the propeller speed and the Sky Force™ will accelerate and ascend. Move the Throttle stick down to decrease the propeller speed and the Sky Force™ will decelerate and descend (see diagram H). While in the air, move the Throttle stick left and the Sky Force™ will rotate left. Move the Throttle stick right and the Sky Force™ will rotate right (see diagram I). While in the air, move the Direction Stick up and the Sky Force™ will move forward. Move the Direction Control down and the Sky Force™ will move backward (see diagram J). While in the air, move the Direction Control left and the Sky Force™ will bank to the left. Move the Direction Control right and the Sky Force ™ will bank to the right (see diagram K). REAR 2. Turn on your Sky Force™ and set it down on a flat level surface. The red and white LED lights of the drone should begin to flash repeatedly. Bottom View 180 PROPEL ARTWORK NO. SKY FORCE™ DIAGRAM Headless Mode Reverse Calibrate Button Power On/Off Battery CHOKING HAZARD - Small parts. Not suitable for children under 3 years. Conforms to safety requirements of FCC. 8619 Wall street, Suite 400, Austin, TX 78754 © 2017 Rooftop Brands™. All Rights Reserved. www.propelrc.com. The red LED on the charger lights off when charging is complete 1. Place the battery into the battery compartment as shown in illustraition E. 2. Make sure the battery is placed in the right direction.Then twist the battery lock to lock the battery securely. Caution: The battery fits only one way! Do not force it. 3. Turn on the ON/OFF switch of the Sky Force™, the LED lights will start flashing if you install the battary properly. WARNING: Never leave product charging unattended for extended periods of time. Always disconnect the battery from charger immediately after the battery is fully charged. Please refer to enclosed safety instructions. Shoot button IMPORTANT: ALWAYS REMEMBER TO UNPLUG YOUR CHARGING CORD WHEN NOT IN USE! SKY FORCE™ BATTERY INSTALLATION SPEED SELECT BUTTON 3. Quickly turn ON the remote and you will notice that the red LED light on the face of the controller should light up and stay solid. The “Battle Indicator” will flash once then off . The lights on the drone will flash slower. 4. Push the left control stick all the way up until it stops and then pull it back all the way down to the bottom(see illustration below). You will hear 2 high-pitched beeps when pulling the throttle up and down. The lights on the drone should stop flashing and become solid. If the lights on both the drone and the controller have stopped flashing and become solid you have successfully synced your Sky Force™ and are ready to fly. If the lights on the controller or the drone are still flashing, repeat steps 1-4 again. The Sky Force™ has 2 speed settings; SLOW, and HIGH. The Default setting when you first turn on your Sky Force™ is the SLOW speed mode. For high speed simply press the “High Speed” button (see remote diagram on pg 3) you will hear 2 beeps and the speed changed to HIGH speed. Speed settings can be set before flight or during the flight. REVERSE BUTTON The Sky Force™ has an REVERSE feature which allows you to operate your drone fly backward automatically. Simply press the REVERSE Button and your Sky Force™ will begin fly backward. To exit the reverse mode simply press the REVERSE Button again or push the direction control stick to any direction. • TIP 1: try not to leave too much time between turning on the drone and the controller or your syncing window will time-out. • TIP 2: Syncing your drone indoors or in the shade will make it easier to see the LED light indicators on both the controller and the drone. HEADLESS MODE BUTTON You can maintain orientation of your Sky Force™ during flight. 1. Once the Sky Force™ is activated press the headless mode button (see controller on pg.3) to activate the internal compass. 2. The flying orientation is now locked to match the direction control lever. Note: Before switch to “headless Mode”,you need place the drone straight ahead right in front of you, Calibrate it first then press the headless mode button. FRONT REAR FLIGHT PRACTICE To master flying your aircraft, try practicing the excersizes shown below. Start with simple vertical takeoffs, landings, and left/right turning and rotating. Once those are mastered move on to square and cross maneuvers. Good luck and have fun! Power On/Off move the control stick all the way up and all the way down you should hear a beep the flashing red LED light will become solid when you are synced Fixed-point landing Square Pattern Maneuver Cross Pattern Maneuver ADJUSTING THE TRIM CALIBRATING THE SKY FORCE™ NOTE: The Sky Force™ is already properly trimmed and calibrated right out of the box and should not require any trim adjustments before flying. Some more experienced pilots may want to adjust trim settings for their style of flying. After several crashes you may need to adjust trim settings for the Sky Force™ to be more balanced. NOTE: Your Sky Force™ comes pre-calibrated out of the box so you are ready to fly. After several crashes and shock to your gyro sensors, you may notice that your drone is drifting and not holding its center position as well as it used to. This most likely means that you need to recalibrate the 6 axis gyro. Please follow the simple instructions below. Forward/Backward Trim • If your Sky Force™ drifts forward while in the air, push and release the BACKWARD TRIM button repeatedly until the motion stops and proper flight is maintained (see diagram L). • If your Sky Force™ drifts backwards, push and release the FORWARD TRIM button forward in the same manner until the problem is resolved. Bank Right/Left Trim • If your Sky Force™ drifts left while in the air, push and release the RIGHT TRIM button repeatedly until the motion stops and proper flight is maintained (see diagram M). • If your Sky Force™ drifts right, push and release the LEFT TRIM button in the same manner until the problem is resolved. HOW TO PERFORM BACK FLIP STUNT Performing back flip stunt with the Sky Force™ is as easy as 1-2-3: 1. Hover the Sky Force™ in still position making sure that you have at least 5 feet of clearance above and below the quadrocopter,. 2. Press and release the stunt button and you will enter the stunt flip mode.The controller will start beeping. (see diagram Q1). 3. Push the right control stick in any direction your Sky Force™ will flip backwards 360˚(see diagram Q2). After stunt flip, it will automatically exit the stunt mode. 4. To exit the Stunt flip mode manually, simply press and release the button again. The controller will stop beeping. 1. Place the Sky Force™ on a flat level surface. 2. Make sure the Sky Force™ is on and that the controller is synced (refer to syncing pg 4. ). Do not start the blades. Press the “calibrate button”. You will see the lights on the drone rapidly flash and then stop. Once the lights stop flashing you have completed your calibration and are ready to fly! TROUBLE SHOOTING: If you do not see the lights flash, restart your controller and the Drone again. Always make sure to put your battery in the copter first, then turn on your controller. Push the left throttle stick up all the way and then pull back down all the way. When you hear the beep the Sky Force™ is synced to the controller and you are ready to calibrate. TROUBLESHOOTING YOUR SKY FORCE™ PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION 1. Power switched off 2. Polarity is reversed 3. Batteries may be low or in need of charging 1. Switch the ON/OFF switch to ON 2. Make sure all batteries are installed correctly (see diagram A on pg.2) 3. Replace batteries 1. Remote is switched off 2. battery power in remote is too weak 3. The remote is not properly synced 4. Out of control range 1. Switch the ON/OFF switch to ON 2.Connect the battery to Sky Force™ 3. Re-sync the remote 4. Do not fly beyond 500 feet Drone Won’t lift off 1. Rotor speed too slow 2. Drone not fully charged 3. Obstruction of rotors 1. Push throttle lever forward 2. Recharge your Sky Force™ 3. Check rotors for hair or other obstructions Drone Decsends Too Fast Moving the throttle down too quickly flying in high wind or bad weather Control the throttle slower, use auto land feature, Do not fly in bad weather No Power Drone Not Responding Stunt Button Q1 Q2 CALIBRATE BUTTON If you continue to encounter problems call our customers service line at (949) 566-9573 Ext 1 for assistance. REPLACING THE PROPELLER BLADES Your Sky Force’s propeller system is a precision instrument that may need repair or replacement from time to time for optimal flight function. Crash landing at high-speed may cause damage to your Sky Force’s propellers. 1. The Sky Force™ has four blades, two gray blades in the front, and two black blades in the back (see the diagram S). 2. When replacing the propeller blades, make sure to match both the color of the blade and the indication letter on the blade. 3. Replace the damaged blade with the correct blade. INTERACTIVE BATTLE MODE NOTE: The use of the Trim buttons utilizes sounds. A single long Beep indicates the product is center trimmed. If there is no beep sound after press the trim button, it indicates the maximum rang of the trim on a particular side. Front The Sky Force™ is designed for indoor & outdoor use. The Sky Force’s blades revolve at high speeds and can cause damage to the user, spectators and animals. Stand away from the Sky Force™ to reduce the risk of getting into the flight path. Warn spectators that you will be flying your Sky Force™ so that they are aware of its position. Before flight, inspect the rotor blades to make sure that the blades are securely fastened to the Sky Force™. WARNING! • Choking/Cutting Hazard. Small Parts/Sharp Rotor Blades. • Keep hands, hair and loose clothing away from the propeller when the power switch is turned to the ON position. • Turn off the transmitter and Sky Force™ power switches when not in use. • The included charger is built specifically for the Sky Force™ Li-Poly battery. Do not use it to charge any other battery. • New alkaline batteries are recommended for maximum performance. • Parental supervision recommended when flying Sky Force™. BATTERY WARNINGS RECHARGEABLE BATTERY: This Sky Force™ uses a Li-Poly rechargeable battery. If battery no longer stays charged, dispose of battery properly according to local disposal requirements. CONTROLLER BATTERIES: Remote control requires 3 “AA” batteries (not included). Please read the important battery safety warning below. • Do not mix alkaline, standard (carbon-zinc) and rechargeable batteries (Nickel Metal Hydride). • Do not mix old and new batteries. • Non-rechargeable batteries are not to be recharged. • Rechargeable batteries are to be removed from the item before being charged (if removable). • Rechargeable batteries are only to be charged under adult supervision. • Exhausted batteries should be removed immediately and must be recycled or disposed of properly according to state or local government ordinances and regulations. • The supply terminals are not to be short-circuited. • Only batteries of the same or equivalent type as recommended are to be used. • Batteries are to be inserted with the correct polarity (see inside booklet for diagram). • Do not dispose batteries in a fire - batteries may leak or explode. CARE AND MAINTENANCE • Always remove the batteries from the wireless remote control when it is not being used for an extended period of time. • To clean, gently wipe the remote control and Sky Force™ with a clean damp cloth. • Keep the toy away from direct heat or sunlight. • Do not submerge the toy into water. This can damage the unit beyond repair. • Parental guidance recommended when installing or replacing the batteries. Gray Blade Front Left = L Gray Blade Front Right = R Black Blade Back Left = R Black Blade Back Right = L SKY FORCE™ WARNING: 11 Get ready for aerial combat missions with your friends . Note: Requires additional Sky Force™. PREPARATION FOR MISSION: 1. Make sure all battling quadrocopters are fully charged, properly synced and ready to fly (refer to SYNCING YOUR Sky Force™). READY, AIM, FIRE! 1. While your Sky Force™’s in flight, aim the front side of your Sky Force™ to your opponent’s Sky Force™ and press the SHOOT button on the top of your remote control (see diagram on pg 3). 2. If you score first hit, your opponent's remote control will vibrate one short time, the Sky Force™ will swing one time, in the mean time the indicator lights will flash one time . 3. If you score second hit, your opponent's remote control will vibrate two short times, the Sky Force™ will swing one time, in the mean time the indicator lights will flash two times . THREE STRIKES YOU'RE OUT! 4. On the third direct hit, your opponent's remote control will vibrate one long time, your opponent’s Sky Force™ indicator lights will flash three times and your opponent will not be able to control the quadrocopter. The quadrocopter will gradually descend to the ground. Mission accomplished! 5. Once the quadcopter fully stops, your opponent can pull the throttle all the way down to recover (reset) and will be ready for the next dogfight. 10
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Count : 2 Producer : GPL Ghostscript 9.07 Create Date : 2017:06:13 14:18:37+08:00 Modify Date : 2017:06:13 14:18:37+08:00 Author : cartlee Creator : PDFCreator Version 1.7.1 Subject : Title : user manual.pdfEXIF Metadata provided by EXIF.tools