Asian Express PL-1630T Ocula HD Viedo Drone + Wifi User Manual
Asian Express Holdings Limited Ocula HD Viedo Drone + Wifi
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3479857 |
| Application ID | H+6raOJLjlFvHErI+F4r9Q== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 345.19kB (4314822 bits) |
| Date Submitted | 2017-07-25 00:00:00 |
| Date Available | 2017-07-25 00:00:00 |
| Creation Date | 2017-07-07 17:32:56 |
| Producing Software | Adobe Acrobat 10.1.1 Image Conversion Plug-in |
| Document Lastmod | 2017-07-07 17:33:44 |
| Document Title | User Manual |
| Document Creator | Adobe Acrobat 10.1.1 |
PREPEL
FCC Part 15 C Notice
CAUTTON: Changes or modifications not expressly approved by the party responsible for compliance could
void the user‘s authority to operate the equipment.
NOTEThis equipment has been tested and found to comply with the limits for a Class B digital device,
pursuantto Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against
harmful interference in a residential installation.This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However,there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorie nt or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
{1] This device may not cause harmful interference, and
(2] this device must acceptany interference received, including interference that may cause undesired
operation.
INDUSTRY CANADA NOTICE: CANADA ONLY.
This device complies with Industry Canada licence-exempt RSS sta ndard(s].0peration is subject to the
following two conditions: (I) this device may not cause interference,and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'lndustrie Canada applica bles aux appareils radio exempts de
licence. L'exploitation est autorise‘e aux deux conditions suiva ntes : (l ) I‘appareil ne doit pas produire de
brouillageet (2) l'utilisateur de [a ppareil doit accepter dout brouillage radioe’lectrique subi, méme si le
brouillage est susceptible d'en compromettre le fonctionnement.
CAN ICES-3 B)INMB-3(B)
This product meets e applicable lnnovation,Science and Economic Development Canada technical
specifications.
Ce produit re'pond aux spe'cifications techniques pertinentes d'lnnovation,Science et Developpement
économique applicables.
m "'
ms;
Requlres Speed CIIE l5 orhlgher micmSD or
micro SDHCcardlnotincluded)
microSDHC Loan is a trademark of SD-SC, LLC.
cmss©
A WARNING!
CHOKIIIG HAZARD A8113" puts.
mmumm underarm:
Conforms to safety requirements of RSSZIO and FCC.
@201? Rooftop BrandsTM All rights reserved
Tel:+ (”949-566-9573 - www.propelrc.com Made in China
1? v2.0
OCU LAT“ H D+WiFi
Indoor/Outdoor HD Drone With Streaming Video
two I 720 pixel
30 franes per second
INSTRUCTION BOOKLET
WARNING: Never leave product charging unattended for extended periods of
time. Always disconnect the battery from charger immediately after the battery
is fully charged. Please refer to enclosed safety instructions.
PACKAGE CONTAINS:
" Hit
‘ I
OCULATM 2.46 Wireless Spare Parts USB Charger USBCard Reader Instruction
Controller 8: Li»Pon Manual
Rechargeable Battery
Colors and styles may vary slightly. PHOPEL
TABLE OF CONTENTS
Features ............................................................... 2
Remote Control Battery Installation ........................................ 2
Charging the Ocula‘” Li—Poly Battery ....................................... 2
OculaT'V‘ Battery Installation ............................................... 2
OculaT'V‘ Diagram ........................................................ 3
Control Diagram ........................................................ 3
Flight Preparation ....................................................... 4
Syncing Your OculaTM .................................................... 4
Now You Are Ready To Fly ................................................ 5
Recognizing The Front 8: Rear Of The OculaTM ................................ 5
Starting/Stopping The Rotors ............................................. 5
Manual Start/Stop ...................................................... 5
Auto Start/Land ......................................................... 5
Understanding The Altitude Lock Sensor .................................... 5
Speed Select Button ..................................................... 6
3 Channel VS 4 Channel Flying ............................................ 6
3 Channel Flight Control ...................................... . .......... 6
4 Channel Flight Control ................................................. 7
Flight Practice .......................................................... 7
Adjusting The Trim ...................................................... 8
Calibrating The OculaT'VI .................................................. 9
How To Perform 360° Stunt Rolls .......................................... 10
Using Your On—Board Camera and Video Recorder ............................ 11
Removing Your microSD Card ............................................. 12
Downloading and Clearing Space on Your microSD Card ....................... 12
Propel OculaTM WiFi APP Installation ....................................... 13
Pairing OculaTM to Your Compatible Device s ................................ 13
Quick Start ............................................................. 14
Detailed APP Overview ................................................... 14
Troubleshooting Your OculaTIM ............................................ 15
Replacing The Propeller Blades ............................................ 15
Warnings .............................................................. 16
Battery Warnings ....................................................... 16
Care and Maintenance ................................................... 16
FCC Information ........................................................ 17
Thank you for purchasing the Ocula'” 2.4 Ghz Duadrocopter. Please read this instruction booklet as it
contains valuable information on how to pmperly fly and care for your Ocula'".
FEATURES
- Wide angle lens provides great aerial photography
- Air pressure sensor locks‘flight altitude
- Stream live video directly to your mobile device
- 720p high definition camera records high quality video and still pictures
- Vibration dampened motors provides quieter flight and improves image quaTrty
- 3 different speed settings for slow to high speed flying
- Led directional lights makes the ocula tm hd+wifi easy to follow
- Push button 360' aerial stunts
- 2.4g radio allows for a 200 feet operational range
REMOTE CONTROL BATTERY INSTALLATION
1. Slide off the battery cover from the back of the contmller.
2. Install 4 fresh‘AA"alkaline batteries into the controller as
shown in diagram A. Replace the battery cover.
3. Turn over the controller and turn the nil/off switch to the on
position. If the power indicator turns on you have installed your
batteries properly.
4x15 vorAA'Alhl'lIe Batteries
CHARGING THE OCULAT'“ Ll-POLY BATTERY
1. Connect USB to the drone as shown (see diagram B).
2. Next, Plug the USB card to the computer.
Note2The drone has a RED LED indicator light to indicate it is charging.
3. When the battery is fully charged the dlarging indicator light will turn Green.
4. Average charging time is approximately 80—100 minutes. A fully drarged drone can fly for
approximately 10 minutes depending on environment and user input.
NOTEzYou may purdtase additional batteries and chargers at www.propelrc.com
‘ J ‘7 . [ED Indicator 7 0 ‘ V
IMPORTANTMLWWS REMEMBER“) DISCONNECT YOUR BATTERY G'IARGERWHEN NOT IN USE!
OCU LAP“ BATTERY INSTALLATION
1. Slide the fully dtarged battery into the Ocula'Ws battery compartment (see diagram C).
The battery is designed to fit in the compartment one—way,do not force it in.
2. Push the battery all the way in and you will hear a didc.
3. Removing the battery: Push down the battery end (see diagram D],then gently pull out the battery.
OCULATM DIAGRAM
Back [Red LED Lights)
Gray Rotor Blades
Black Rotor Blades
landing Gear
LED Indicator Lights
USB Charging Interface microSD Card Slot
Power Indicator Light
Auto Start/ Land Button
Speed Button 360' Stunt Roll Button
ForwardlBackward Trim
Throttle Stick Direction Stidt
Left/Right
Turn Trim
Power OnIOff Left/Right Bank Trim
Speed Indicator
.— 3 (H Mode/4 (H Mode
Back of Remote-Controller
WARNING
DO NOT FLY YOUR OCULAT" IN FOUL WEATHER!
ease
FLIGHT PREPARATION
- Verify that there are UM" batteries inside the remote control unit and the OculaTM has been
fully charged.
- Make sure to be in a large open space preferably a field or a park with an open radius of at least 200feet.
- Make sure to start your drone on a dean flat level surface before take—off.
‘ IMPORTANT! Until you have experience in flying your Oculam, it is not advised to use in any rate of wind.
Pick a day with zero wind day or extremely light wind condition when learning how to fly.
SYNCING YOUR OCULATM
Important! When syncing your OculaTM with the controlleralways make sure that the drone is on a
flat level surface and that your digital trim settings are in the center position.This insures that the 6
Axis gyro is properly programmed to respond to your trim settings.‘r'our OculaTM utilizes an automatic
2.46 channel selection system that allows up to 8 people to fly side by side in the same wireless range with
no interference.
l . Before starting,make sure that the power switch on your controller is off and the battery is removed
from the DculamMake sure that there are no other 2.46 devices in the area.
2. Insert the battery into the OculaT" and set it down on a flat level surface. Push down the power button and
hold for a few seconds [see diagram D1).The red and white LED lights on the drone should begin to flash
very quidt for a few seconds then slower.
3.0uidtly turn ON the remote and you will notice that the top red LED light on the face of the controller
should also be flashing.
4. Push the throttle stick all the way up until it stops and then pull it back all the way down to the
bottom (see diagram below).When pushing the stidt up or pulling the stidt down you should hear a
high-pitched beep both ways and the indicating light will stop flash and stay solid on. You have
successfully synced your Oculam and are ready to fly. If this doesn't happen repeat steps 1—4 again.
- TIP 1: Try not to leave too much time between putting your battery into the
drone and turning on the controller or your syncing window will time-out.
-TlP 2: Syncing your drone indoors or in the shade will make it easier to see the
LED light indicators on both the controller and the drone.
In Move the control stidt all the way
u and all the w down,you
s ould hear two eeps.
The flashin red LED light will
become so Id when you are
synced.
NOW YOU ARE READY TO FLY!
If you have successfully synced your Ocula‘" to your controller as explained on page 4 you are now ready to
fly. Before beginning to fly your drone you should familiarize yourself with how to start and stop the rotors,
how to use your auto land feature and how the controls work so please carefully read and familiarize
yourself with various control features explained in the next few pages. Once again as a beginner pilot you
should leam how to control your drone in a large open field or park on a day with zero orvery light wind.
Do not try to fly your Ocula‘“ too high until you become a more experience pilot.
RECOGNIZING THE FRONT 84 REAR OF THE OCULATM
Even though the OculaTM has four rotors there Is still a front or
"forward" facing direction and "rear" or backwards facing direction.
The front and forward facing direction of the Ocula'M is the side
with two EYES (see diagram E ).The rear and backward facing
dIrection ofthe Quadrocopter is the side with battery compartment
(see diagram E).
IlflTizThe front of the Ouadrooopter also displays running WHITE LED
light and the back of the Quadrooopter displays running RED LED
lights.
STARTING/STOPPING THE ROTORS
Note:You can start/stop your OculaTM manually or automatically.
Please follow one of the steps below to operate accordingly. Make sure you
have properly synced the Oculam and the power stays on.
MANUAL START/STOP
- To start the rotors simply move the two control stidts both down and out
(see dagram),hold until the rotors start spinning. Now release both
stidts to the neutral position and push the throttle up to take off.
-To stop the rotors, alter starting them you can simply wait about 10
seconds, and they will stop automatically.0r move both stidts down and
out again to stop immediately. After take off, you can simply pull the
throttle allthewaydownaml land.
AUTO START/LAN D
The Ocula'”I has an auto startllaod feature which allowsyou to stam'land
automatically.Simply pressthe AUTO START] LAIID button on the topof
the controller and your Ocula'" wil begin taking oflllaminghee tiagram
below).
NOTE:You can still control the direction while auto startingllanding to
avoid obstacles.
UNDERSTANDING THE ALTITUDE LOCK SENSOR
The Ocula'" has a unique Altitude Lock function,air pressure sensor that allows for easier flight control and
stability.h beginner's friend, it allows the user to ease into piloting the copter.The sensor locks in the altitude
of the copter while allowing the user to adjust the directional controls without having to hold the throttle.
After starting the copter, fly it upwards to a safe height. Once at a safe height, release the throttle to the
neutral position. Now your Ocula'" should be locked in the altitude and you can focus on getting used to the
directional controls of the Ocula'”.The copter will always tend to self correct and go back to the last locked
height after moved up or down by outside forces.
Note: The altitude sensor does have some tolerance based on atmospheric conditions and could have a slight
variation in altitude.
SPEED SELECT BUTTON
The OculaT'“ has 3 speed settings; I (SLOW), 2 (MEDIUM) and 3 (HIGH).The Default setting when you first
turn on your OculaTM is the l (SLOW) speed mode.To increase the speed simply trigger the speed setting
button (see remote diagram on pg 3) you will hear a beep and the speed setting indicator on the face of the
controller will show you what speed setting you are on.Speed settings can be set before flight or during the
flight.
3 CHANNEL VS 4 CHANNEL FLYING
Propels unique‘switch-blade'tedlnology allows you to choose between 3ch or 4ch flight control modes.
Most people with no experience in flying multi copters may find 3ch easier to learn at first as controls are
set up to simply move forward, back,tum left and turn right. 4dIannel flying gives the operator ultimate
control by adding two more dimensions of flight,banking left and banking right.
To dlange to 3 Channel mode:
Switch the 3/4 (H button to left side on the back ofcontroller (see remote diagram on pg 3),you will hear 3
“beeps" indicating the Ocula"M now is set to 3 CH mode.
To dlange to 4 Channel mode:
Switch the 3/4 (H button to right side on the back of controller (see remote diagram on pg 3).you will hear
4"beeps" indicating the OculaTM now is set to 4 (H mode.
3 C HANNEL FLIGHT CONTROL
Below is a list of basic flight functions for your long—range remote to control the OaIlaWWhile learning to
fly your Ocula‘l‘| it is best to startin a large space with the drone facing away from you until you get usedto
the basic controlsAsyou master flying your Ocula‘” you can move to more advanced maneuvering
techniques. Practice makes perfect! When you have these basic stepsdown you can move to the next level.
Move the left Throttle stick up to increase the
propeller speed and the Ocula'” will accelerate
and ascend.
Move the left Throttle stick down to decrease the
propeller speed and the Ocula'" will decelerate
and descend (see diagram F).
While in the air, move the right Direction Stick up
and the Ocula'" will move forward.
Move the right Direction Control down and the
Ocula'"I will move backward (see diagram G).
While in the air, move the rigid Direction Control left
andtheOculamwillspintotheleft.
Move the right Direction Control right and the
Ocula'”I will spin to the right (see diagram H).
4 CHANNEL FLIGHT CONTROL
Below is a list of basic flight functions for your long-range remote to control the 0cula‘".While learning
to fly your ()culaTM it is bestto start in a large space with the drone facing away item you until you get used
to the basic controlsAs you master flying your Ocula'” you can move to more advanced maneuvering
techniques. Practice makes perfect!
Move the leftThrottle stidc up to increase the
propeller speed and the Ocula‘“ will accelerate
and ascend.
Move the leftThrottle stidc down to decrease the
propeller speed and the Ocula‘“I will decelerate
and descend (see diagram I).
While in the air, move the left Throttle stick left
and the Ocula‘" will rotate left.
Move the leftThrottle stidc right and the
Oculai" will rotate right (see diagram J).
While in the air, move the right Direction Stick up
and the Ocular” will move forward.
Move the right Direction Control down and the
Ocula'"| will move backward (see diagram K).
While in the air,move the right Direction Control left L
andtheocula'Mwillbanktothe left. W“
Move the right Direction Control right and the «
Ocula'“ will bank to the right (see diagram L).
FLIGHT PRACTICE
To master flying your aircraft try practicing the excersizs shown below. Start with simple vertical takeoffs,
Iandings,and left/rig ht turning and rotating. Once those are mastered move on to square and cross
maneuvers. Good ludc and have fun!
Cross Pattern Maneuver
Fixed—Point landing Square Pattern Maneuver
ADJUSTING THE TRIM
NOTE: The Ocula'" is already properly trimmed and calibrated right out of the box and should not require
any trim adjustments before flying. Some more experienced pilots may want to adjust trim settings for
their style of flying. After several crashes you may need to adjust trim settings for the Ocula‘" to be more
balanced.
Forward/Backward Trim
- If your Ocula'” drifts forward while in the air,push
and release the FORWARDIBACKWARD TRlM button
backward repeatedly until the motion stops and
proper flight is maintained (see diagram M).
- If your Ocula‘" drifts backwards, push and release
the FORWARD/BACKWARD TRIM button forward in
the same manner until the problem is resolved.
Bank Right/Left Trim
- If your Ocula'" drifts / banks left while in the air,
push and release the BANKS TRIM button to the
rightside repeatedly until the motion stops and
proper flight is maintained (see diagram N).
- If your Ocula'” drifts right, push and release the
BANKS TRIM button to leftside in the same manner
until the problem is resolved.
Spin Left Trim
- If your Ocula‘" spins left while in the air,push and , ’ " ’
release the LEFT/RIGHT TURN TRIM button to the '
rightside repeatedly until the motion stops and
proper flight is maintained (see diagram 0).
Spin Right Trim
- If your Ocula'” spins right while in the air, push and
release the LEFT/RIGHT TURN TRIM button to the
leftside until the problem is resolved (see diagram 5'7
P). "
NOTE: The use of theTrim buttons utilizes sounds.A single long Beep indicates the product is
center trimmed.No sound after press the trim button indicates the product is trimmed to the
maximum on a particular side.
CALIBRATING THE OCULATM
NOTEYour OculaT'“ comes pre-calibrated out of the box so you are ready to fly.
After several crashes and shocks to your gyro sensors,you may notice that your drone is drifting and can
not hold its center position as well as it used to.
This most likely mea nsthat you need to recalibrate your Oculam. Please follow the simple instructions
below.
1.Place the OculaTM on a flat level surface
2. Make sure the OculaTM is on and that the controller is synced (referto syncing pg 4). Do not start the
blades. Instead move both the throttle and control stick down and to the right comer and hold them
there for 5 seconds(see diagram R).You will see the lights on the drone rapidly flash and stop. Once the
lights stop flashing you have completed your calibration and are ready to fly!
TROUBLE SHOOTING: If you do not see the lights flash,first remove the battery from the drone then turn off
your controller and start again.Always make sure to put your battery in first,then turn on your controller.
Push the left throttle stick up all the way and then pull back down again.When you hearthe beep the lJc1ilaTM
is synced to the controller and you are ready to calibrate.
HOW TO PERFORM 360° STUNT ROLLS
Performing 360° stunt rolls with the OlculaTM is as easy as 1-2-3:
1. Hover the OculaT” in still position ma king sure that you have at least 5 feet of clearance above and below
the quad rocopter, Set the speed settings to mode 2 or 3.
2. Pressthe 360 stunt button down and you will enter the stunt roll mode which is indicated by rapid
beeping (see diagram 5) sounds.
3. Determine which direction you want it to flip and quickly push the right control stick in the direction
you want to flip your OculaTM (see diagram T).
You have 4 choices a) Forward roll, b) Backwards roll, c) Right side roll, d) Left side roll.
360“ Stunt Roll Button
NOTE:To exit the stunt roll mode without flip, you can press the button again.The beeping sound
will stop.
10
USING YOUR ON-BOARD CAMERA AND VIDEO RECORDER
Your Ocula'"l comes equipped with an onboard digital camera(12801720 pixei,30 frames per second) that
takes both video and still photographs. Now you can have hours of fun creating aerial photography and
videos for family and friends.
WHAT YOU WILL NEED TO GET STARTED USINGVOUR CAMERA
1. One microSD cardinot induded).
2. One microSD card reader(included).
FORMAT 'ITNG YOUR microSD CARD
Before you can begin to take videos or digital photographs you must first format your miaoSD card. To
format your microSD card simply place the microSD card into the included USB SD card reader and plug it
into your computers USB port (see diagram U1 and U2 below).After a few moments an icon will appear on
your Desktop. Right click on the Icon and follow instructions to format your microSD card.
INSTALLING THE microSD CARD INYOUR OcuIa'"l
- Place the formatted microSD card into the Ocula'” SD card port (see diagram U3 below). Push gently until
you hear and feel the microSD card'diclr'into the SD card slot.
- Turn the Ocula'" on and make sure that it is both fully charged and properly synced to the controller (see
HOW TO SYNCYOUR OUADROCOPTER on page 4).
NOTE: If you see a blue LED light flashing this indicates you have not installed your microSD card correcfly
or there is a problem with your SD card(see diagram U4 below). If this happens please reformat and try
again.
TAKING DIGITAL PHOTOS
To take photographs short press the CAMERA button on the top right side of the controller (refer to
CONTROLLER DIAGRAM on pg. 3),when you push the button you will hear a "beep" and the red and white
ted lights on the will flash one time indicating that a picture has been taken.
RECORDING VIDEOS
To begin recording a video long press CAMERA button for 2 secondsYou will hear a "beep" and the red
and white LED lights on the camera start flashing to indicate that you are in video mode and the camera is
recording.To stop the video recording,long press the CAMERA button a second tirne,you will hear a”beep"
indicating that the video recording has stopped and the Camera is in ready mode again.
Diagram Ut Diagram U2 Diagram U3 Diagram U4
IMPORTANT NOTICEYou can not take photos and videos at the same time.When you are in video mode
the photo function is disabledeyou want to take photos you mustt'rrst exit video mode. It‘s
recommand to testyorrr camera functions beforefly'ng.
I'I
3. A Cornputerwith a USB portand Windows Media Player orother Media playerthat can play AVI tilesinot irrduded).
REMOVING YOUR microSD CARD
To remove your microSD Card push in gently on the back of the SD card with your thumb or forefinger until
you hear and feel a‘clidring sound'.’ The microSD card witl'pop-out'slightiy and is ready for removal.
Simply grab and pull gentiy away from the Oculams camera port to remove the card. Always store your
microSD card in a clean,safe and tool environment.
DOWNLOADING AND CLEARING SPACE ON YOUR microSD CARD
Plug your microSD card into the microSD card reader and connect to your computer. It is best to always
download all your videos and pictures on to your computer and not store this data on your microSD card.
After downloading your photos and videos ,foliow your computers instructions to'delete' files on your
microSD card.
IMPORTANT NOTICE:When your microSD card is full the indicator light on the bottom of your Oculam|
wil not flash when you press the photo or video record buttonthis indicates that its time to put a
new SD card in your Ocula‘" or download files and dear spaceforfuture photos and videos.
12
13
PROPEL OCULATM WiFi APP INSTALLATION
I. Make sure you are using a compatible AndroidT'“ or Apple‘fi’ iOS device.
2. Make sure your device has access to the Internet.
3. For Apple"m iOS devices,within the App Store,seardl and select “ Propel OculaTM WiFi'.’ Hit the Install
button and the"PropeI OculaTM Wifi"App should download and install automatically.
4. For AndroidTM OS devices,visit the Google Play store and search for”Propel ()culaTM WiRi’Selecting the
"Propel 0cuIaT"‘ WiFi"App will download the App and automatically install it on your device.
5. After the ”Propel OculaTM Wifi” App is installed,it should create an icon on your screen. Click the"Propel
OculaTM WiFi"icon to run the App to make sure that it has installed correctly on your device. If not, please
delete and repeat the process again.
PAIR] NG OCU LATM TO YOU R COM PATI BLE DEVICE
1. After completely charging your OculaTM battery, in stall the battery to your OculaTM (refer to the user
manual}.
2. In the Settings menu of your device,locate the Wi—Fi option.
3.Turn ON the Wi-Fi option.
4. Select"Propel 0cu|aTWfrom the Wi—Fi list.Waitfor your OculaTM to be connected Return to the Main Menu.
Settings
Airplane Nude
Propel (lculaTM WiFi
Note: Apple® devices require the use of iOS 7.0 or higher.
ANDRDIDTM devices require the use of OS 4.2.2 or higher.
QUICK START
T.After you install the App carrectlyand have paired to the drone successfully you can open the “Propel Ocula‘TM
WiFi”App icon. Tap “STA/iron the bottom right hand side of the screen. You should see the real—time video
streaming tram your Ocula TM’s camera.
2. This App also allows you to control your OculaTM by your mobile device. To activate the control sticks, tap the
”ON” button at the top right hand side of the screen. This will switch the control from your traditional
controller to your compatible device. Now click" [E ”to start the motors. The control sticks will show up in
the screen for your fly control and you can now use your device as a traditional controller. Or you can clic "
."to auto launch your Ocula’” in the air and then use your device as a traditional controller. Click this
button again, your Oculam‘ will automatically land on the floor.
DETAILED APP OVERVIEW
3. Please see images below for a detailed App overview This overviewis also available under the ”HELP”icon
in the home screen of the App.
CONTROL STIC KS
HOMEPAGE
i3 H .7 e E L
4. Ifyou’re still encaun tering difficulties please contact our customer service department at
+ 1 -949-566-95 73 (U SA)
14
PROBLEM
15
Blade From Left = A
Blade Front Right = B
Blade Back Left = B
Blade Back Right = A
TROUBLESHOOTING YOUR OCULATM
POSSIBLE (AUSE
1. Power switched off
1 Polarity is reversed
3. Batteries may be lower in need ofdiarging
1. Remote is switched off
lBattery powerin remote is too weak
3. The remote is not properly synced
4. Out of comml range
1. Rotor speed too slow
2. Aircraft not hilly charged
3. Obstruction of rotors
1. Moving the throttle down too quickly
2.Flying in high wind or bad weather
REPLACING THE PROPELLER BLADES
Your Oculam's pmpeller system is a precision instrument that may need repair or replacement from time to
time for optimal flight function.(rasli landing at high—speed may cause damage to your Oculam's propellers.
1. The Ocula'" has four blades,two blades with indication number A & B on front,and two blades with
indication number B & A on back [see the diagram V).
2. When replacing the propeller blades, make sure to match the indication number on the blade.
3. Replace the damaged blade with the correct blade.
POSSIBLE SOLUTION
1.5witdr theON/OFF switch to ON
2. Make sure all batteries are installed
correctly (see diagram A)
3. Replace batteries
1.5witdr theOllfOFF switch to ON
2.Replace remote batteries
3.Re-syncthe remote
4.Do notfly beyond 500 feet
1.Push throttle lever forward
2. Rediarge your 0cula"“l
mm rotors forhair orother obstructions
1.Crrrtrdtlietlririttleslorrerlrisearrtolarlfeatire
2.00 not fly in bad weather
Front
NOTE:The "a” and "b" marks are embossed on the bottom side of the propellers.
OCULAT'“ WARNING:
The Ocula"Ml is designed for OUTDOOR use.The 011]th blades revohre at high speeds and can cause
damage to the usetspectators and animals. Stand away from the Ocula‘”I to reduce the risk of getting into
the flight path.Wam spectators that you will be flying your Ocula‘“I so that they are aware of its position.
Before flight,inspect the rotor blades to make certain that the blades are secume fastened to the Ocula'".
WARNING!
- Choking/Cutting Hazard.Small Parts/Sharp Rotor Blades.
- Keep hands,hairand loose clothing away from the propeller when the power switch is trirned to the
ON position.
- Tum off the transmitter and Ocula'" power switches when not in use.
- The included drarger is built specifically for the Dculalwl Li-Poly battery. Do not use it to charge any other
battery.
- New alkaline batteries are recommended for maximum performance.
- Parental supervision recommended when flying Ocula'”.
BATTERY WARNINGS
RECHARGEABLE BATTERY:
This Ocula'" uses a Li—Poly rechargeable battery. It battery no longer stays charged, dispose of battery
properly according to local disposal requirements
CONTROLLER BATTERIES:
Remote control requires 4'M"batteries (not included).
Please read the important battery safety wa ming below.
- Do not mix alkaline,standard (carbon-zinc] and rechargeable batteries [Nidrel Metal Hydride).
- Do not mix old and new batteries.
- Non-rechargeable batteries are not to be recharged.
- Rechargeable batteries are to be removed from the item before being charged (if removable).
- Rechargeable batteries are only to be drarged underadult supervision.
- Exhausted batteries should be removed immediately and must be recycled or disposed of properly
according to state or local government ordinances and regulations.
-The supply terminals are not to be short—circuited.
- Only batteries of the same or equivalent type as recommended are to be used.
- Batteries are to be inserted with the correct polarity (see inside booklet for diagram].
- Do not dispose batteries in a tire — batteries may leak or explode.
CARE AND MAINTENANCE
- Always remove the batteries from the wirelss remote control when it is not being used for an extended
period of time.
-To clean,gently wipe the remote control and Ocula'” with a clean damp cloth.
- Keep the toy away from direct heat or sunlight.
- Do not submerge the toy into water.This can damage the unit beyond repair.
- Parental guidance recommended when installing or replacing the batteries.
IC Radiation Exposure Statement
FCC RF EXPOSllle statements This equipment oornplies wrth IC radiation exposure limits set lorth for an
This Transmiter must not be to - located or operating in conjunction with any uncontrolled environment This solionem should be installed and operated with
em antenna 0' transmitter mininum distance 20cm between the radiator & your body.
This equ'oment complies with FCC RF radiation exposure l'rnits set forth for an
incontrolled environment This equ'pment shorld be installed and operated with a
minrnum distance of 20 centimeters between the radiator and you body or nearby
persons.
Déclaratron d’exposition aux radiations:
Cet équipernent est contomie aux l‘rnites d’exposition aux mynnnements IC
élablies pour un environriemenl non controlé, Cet équipement doit étre installé et
utilise avec un mininun de 20 cm de distance entre la solute de rayounemenl et
votre corps.
16
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Create Date : 2017:07:07 17:32:56+08:00 Creator : Adobe Acrobat 10.1.1 Modify Date : 2017:07:07 17:33:44+08:00 XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2017:07:07 17:33:44+08:00 Creator Tool : Adobe Acrobat 10.1.1 Format : application/pdf Document ID : uuid:712b98cc-cdc7-1c40-b377-beafa420252b Instance ID : uuid:fc8dd27f-4396-cc47-bbb7-4a135ab5f7bf Producer : Adobe Acrobat 10.1.1 Image Conversion Plug-in Page Count : 9EXIF Metadata provided by EXIF.tools