Asian Express PL-1760T Tunnel/X09 User Manual C60 WM X09 Tunnel IM ENG 20180604

Asian Express Holdings Limited Tunnel/X09 C60 WM X09 Tunnel IM ENG 20180604

Users Manual

WARNING: Never leave product charging unattended for extended periods
of time. Always disconnect X09 from charger immediately after the X09 is
fully charged. Please refer to enclosed safety instructions.
INSTRUCTION BOOKLET
Colors and styles may vary slightly.
PACKAGE CONTAINS:
2.4G Wireless Controller Instruction BookletSpare PartsUSB Charging Cord
X09
INDUSTRY CANADA NOTICE: CANADA ONLY.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter dout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Conforms to safety requirements of
RSS210
and FCC.
©2018 Rooftop Brands™ All rights reserved
4ELsWWWPROPELRCCOM
Made in China
V 1.0
CHOKING HAZARD
-
Small parts.
Not suitable for children under 3 years.
WARNING!
11
FCC Part 15 C Notice
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
s2EORIENTORRELOCATETHERECEIVINGANTENNA
s)NCREASETHESEPARATIONBETWEENTHEEQUIPMENTANDRECEIVER
s#ONNECTTHEEQUIPMENTINTOANOUTLETONACIRCUITDIFFERENTFROMTHATTOWHICHTHERECEIVERISCONNECTED
s#ONSULTTHEDEALEROREXPERIENCEDRADIO46TECHNICIANFORHELP
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Palm Sized High Performance Drone
X09
4HANKYOUFORPURCHASINGTHE')NDOOR/UTDOOR80LEASEREADTHISINSTRUCTIONBOOKLETASIT
contains valuable information on how to properly fly and care for your X09.
FEATURES
sAir Pressure Sensor Locks Flight Altitude
s"UILT)N!XIS'YROSCOPIC#HIP+EEPSTHE8%XTREMELY3TABLEIN!LL#ONDITIONS
s44RAINING-ODE(ELPS"EGINNER0ILOTS,EARN(OWTO&LY
s Automatically Start and Lands with The Push of A Button
s$IFFERENT3PEED3ETTINGSFOR3LOWTO(IGH3PEED&LYING
REMOTE CONTROL BATTERY INSTALLATION
1. Unscrew and remove the battery cover from the back of the remote control.
2. Install 2 “AAA” alkaline batteries into the battery compartment as shown in
the diagram A1.
3. Replace the battery cover and secure it.
CHARGING THE X09
1. Before playing, you need to charge the X09 battery first. Connect the USB charging
cord to the charging socket on the battery side. (See diagram A)
Caution: The USB plug fits the charging socket only in one way. Do not force it.
2. Connect the X09 charging cord to your computer’s USB port (see diagram B).
Caution: Only use this charging cord with a computer USB port! Do not attempt
to use other USB charging devices.
3. 4HERED,%$ONTHE53"PLUGLIGHTSUPWHENCHARGINGISCOMPLETE3EEDIAGRAM#
Note: If the red LED lights up, either the charging is complete or the USB plug is
not properly connected.
4. The average charging time is approximately 35-40 minutes. The X09 operates
for about 5 minutes per charge.
Low battery indication: the X09 ‘s LED lights will begin to flash to notify
you that the battery is running low. 45 seconds after the LED lights start flashing
your X09 will automatically land to the floor.
TABLE OF CONTENTS
Features ............................................................................................................ 2
Remote Control Battery Installation .............................................................................. 2
Charging the X09.................................................................................................. 2
8$IAGRAM2EMOTE$IAGRAM................................................................................... 3
Preparing for Flight ................................................................................................4
Syncing Your X09..................................................................................................4
Flying Tips .......................................................................................................... 4
Now You Are Ready To Fly ! ........................................................................................ 5
Recognizing the Front and Rear of the X09 ....................................................................... 5
!UTOMATICALLY4AKE/FF,AND..................................................................................... 5
Understanding The Altitude Lock ................................................................................ 5
Speed Setting Button ............................................................................................. 5
T (Training) Mode ................................................................................................. 5
Understanding Trim Adjustments................................................................................ 6
&ORWARD"ACKWARD4RIM ......................................................................................... 6
"ANKING,EFT2IGHT4RIM ....................................................................................... 6
#HANNEL3ELECT................................................................................................. 7
4 Channel Flight Control .......................................................................................... 7
3 Channel Flight Control .......................................................................................... 8
Calibrating the X09 ................................................................................................ 9
(OW4O$O3TUNT2OLLS....................................................................................... 9
X09 Warning: ..................................................................................................... 10
Battery Warnings, Care and Maintenance ...................................................................... 10
Replacing the Propeller Blade ...................................................................................10
FCC Part 15 C Notice .............................................................................................. 11
A
B.
Battery Compartment
(2 “AAA” batteries not included)
1 2
C
D
4HERED,%$ONTHE53"
plug lights up when
charging is complete
Li-Poly
Battery
Li-Poly
Battery
X09 DIAGRAM
REMOTE DIAGRAM
Landing Gear
Safety Guard
Rotor Blade
FLYING TIPS
s)TISRECOMMENDEDTHATYOUOPERATETHE8INAWIDESPACE4HEIDEALSPACESHOULDHAVEAMFT
radius.
s0ARENTALGUIDANCEORADULTSUPERVISIONISSUGGESTEDATALLTIMES
s)FYOUAREFLYINGTHE8WITHOTHERSMAKESUREALLSPECTATORSAREBEHINDYOU
s&ORBESTPERFORMANCEITISRECOMMENDEDTHATYOUOPERATETHE8INZEROWINDCONDITIONS
Wind can greatly affect the performance of the X09.
Important! When syncing your X09 copter with the controller always make sure that the copter is
on a flat level surface. This insures that the 6-axis gyro is properly programmed to mimic your
trim settings.
Your
X09
utilizes an automatic 2.4G channel selection system that allows up to 8 people to fly side by
side in the same wireless range.
For One-person Play:
1. Before starting, make sure that both your controller and X09 are powered off . Make sure that there
are no other 2.4G devices in the area as well.
#ONNECTTHEBATTERYINTOYOUR8ANDSETITDOWNONAFLATLEVELSURFACE4HEWHITEANDRED,%$
indicators of the X09 should start flashing rapidly.
4URN/.YOURREMOTEANDYOUWILLHEARSHORTBEEPTHEWHITEANDRED,%$LIGHTSWILLSTARTFLASHING
slower. Push the throttle all the way up then pull it all the way down. You will hear 2 beeps and the
,%$LIGHTSWILLTURNSOLID9OUR8ANDREMOTESHOULDHAVESUCCESSFULLYSYNCED3HOULDTHISNOT
happen, repeat all steps again.
For Multi-person Play:
4. Before starting, make sure that all X09s and Controllers are powered off. Make sure that there are no
other 2.4G devices in the area as well.
5. Each person will have to sync their X09 individually at a different time to avoid interference.
Follow steps 1 to 3 above, making sure to keep away from other people while also making sure that
no one else is syncing at the same time.
6.
After syncing one player's X09, it should be left ON until all players have synced their
X09s
.
3HOULDTHEREBEAMISTAKEINTERFERENCEALLPLAYERSMUSTTURNOFFTHEIRCONTROLLERSANDX09s and start
the process all over again.
SYNCING YOUR X09
DO NOT FLY YOUR X09 IN FOUL WEATHER!
WARNING
sVerify that there are 2 “AAA” batteries inside the remote control unit and the X09 has been fully charged.
s
Make sure to be in a large space with an open radius of at least 50 feet.
sMake sure the empty space has no obstacles or rivers. Set your X09 on a clean flat surface before take-off.
DO NOT ATTEMPT TO FLY YOUR X09 IF THERE IS RAIN, SNOW, HEAVY WINDS, THUNDER OR LIGHTNING
OUTDOORS. IT COULD DAMAGE YOUR PRODUCT AND POSSIBLY EVEN CAUSE BODILY HARM.
PREPARING FOR FLIGHT
3 4
4HROTTLE9AW $IRECTION#ONTROL
Right Trim
Left Trim Backward Trim
Forward Trim
Speed Setting Stunt Roll
!54/3TART,AND
Power Switch
Power Indicator
NOTE: The use of the Trim buttons are accompanied with a beep tone. A single long beep indicates the product is
centre-trimmed. No beeping after press the trim button indicates the product is trimmed to the maximum on a particular side.
UNDERSTANDING TRIM ADJUSTMENTS
Forward/Backward Trim
s)FYOUR8ISMOVINGFORWARDSORBACKWARDSAUTOMATICALLYYOUMAYNEEDTOADJUSTTHE
&/27!2$"!#+7!2$42)-BUTTONS
sÈ)FYOUR8FLIESFORWARDPUSHANDRELEASETHE"ACKWARD42)-BUTTONREPEATEDLYUNTILTHEMOVING
stops and proper flight is maintained.
sÈ)FYOUR8FLIESBACKWARDSPUSHANDRELEASETHE&ORWARD42)-BUTTONINTHESAMEMANNERUNTILTHE
problem is resolved.
s&ROMTIMETOTIMEYOUMAYHAVETOADJUSTTHE&/27!2$"!#+7!2$42)-TOENSURETHE8WILL
hover in mid-air and respond accurately to your commands.
Banking Left/Right Trim
s)Fyour X09 is not steadily hovering and is banking to the left or right automatically, you may need to
ADJUSTTHE"!.+).'42)-BUTTONS
s)FYOUR8BANKSTOTHELEFTPUSHANDRELEASETHE24RIMBUTTONREPEATEDLYUNTILTHEBANKINGSTOPSAND
proper flight is maintained.
s)FYOUR8BANKSTOTHERIGHTPUSHANDRELEASETHE,4RIMBUTTONINTHESAMEMANNERUNTILTHEPROBLEM
is resolved.
s&ROMTIMETOTIMEYOUMAYHAVETOADJUSTTHE"!.+).'42)-TOENSURETHE8WILLANDRESPOND
accurately to your commands.
RECOGNIZING THE FRONT AND REAR OF THE X09
Even though the X09 has four rotors there is still a front or
forward-facing direction and back or backwards-facing
direction. The Front and forward-facing direction of the X09 is
the side with two holes. The rear and back of the X09 is where
THEBATTERYCHARGINGSOCKETANDTHEPOWER/./&&IS. The X09
when in flight will also help you keep aware of the orientation
WITHLIGHTED,%$LIGHTSINTHEARMSOFTHE8
NOTE: The front of the copter displays WHITE LED light and the
back of the copter displays RED LED light.
Forward/Backward
Trim Controls Push backward trim button Push forward trim button
If flying forward...
If flying Rightward... If flying Leftward...
If flying backward...
Left/Right Banking Controls Push the “ L ” trim button
to increase left banking
sensitivity
Banks Trim
Banks Trim
AUTOMATICALLY TAKE OFF / LAND
Make sure you have properly synced The X09.
sSIMPLYPRESSTHE!UTO3TART,ANDBUTTONYOUR X09
will automatically take off.
s4
o stop or land the 8JUST0RESSTHE!UTO3TART,AND
button again and the
X09 will descend and land
automatically.
Tips: You also can move the two control sticks simultaneously
down to the inside corners, hold them till you hear a “beep”
and the blades start spinning. Release the control sticks and
push the throttle stick slowly to take off manually.
Forward/Backward Trim
Push the “ R ” trim button
to increase Right banking
sensitivity
5 6
Front
Rear
A
B
B
A
If you have successfully synced your X09 to your controller as explained on page 4 you are now ready to fly.
Before beginning to fly your drone you should familiarize yourself with how to start and stop the rotors,
how to use your take off and auto land feature and how the controls work. please carefully read and
familiarize yourself with various control features explained in the next few pages. Once again as a beginner
pilot you should learn how to control your drone in a large open field or park on a day with zero or very
LIGHTWIND$ONOTTRYTOFLYYOURX09 too high until you become a more experienced pilot.
NOW YOU ARE READY TO FLY!
UNDERSTANDING THE ALTITUDE LOCK
The X09 has a unique Altitude Lock function. With the help of air pressure sensor you can control, your
X09 more stable than ever. The sensor locks in the altitude of the copter while allowing the user to adjust
the directional control without having to hold the throttle.
After starting the copter, fly upwards to a safe height. Once at a safe height, let go of the throttle control,
your X09 should lock in the altitude and allow the user to focus on getting used to the directional
controls.
NOTE: The altitude sensor does have some tolerance based on atmospheric conditions and could have a
slight variation in altitude.
SPEED SETTING BUTTON
The X09 has 4 speed Modes; T(Training),1(SLOW),2(MEDIUM) and 3(HIGH)4HE$EFAULTSETTING
when you first turn on your X09 is 1(SLOW). Short press speed button you can switch among the 3
speed settings.
T (Training)MODE
Simply press and hold the Speed Button,you will hear a long beep indicating you are in T Mode now.
T mode allows you to learn how to operate your X09 at a very slow speed. Also there are maximum and
minim height limits set to avoid crashing to ceiling or floor in T mode. To exit T mode just press the speed
setting button again.
3 CHANNEL FLIGHT CONTROL
For beginner pilot, you may want to practice in 3 CHANNEL mode first. Press the direction control stick
vertically down, you will hear a beep and now you are in 3 CHANNEL mode. Follow the below steps to
STARTYOURFLIGHTPRACTICE.OTE4OSWITCHBACKTO#(!..%,-/$%JUSTPRESSTHE$IRECTION#ONTROL3TICK
again, you will also hear a beep too.)
Move the Throttle up to increase the speed of
the motors and the X09 will rise up.
Move the Throttle down to decrease the speed of
the motors and the X09 will descend.
Move the Throttle stick left and the X09 will
rotate left.
Move the Throttle stick right and the X09 will
rotate right.
-OVETHE$
irection Control up and the
X09 will
move forward.
-OVETHE$IRECTION#ONTROLDOWNANDTHE8
will move backward.
-OVETHE$IRECTION#ONTROLLEFTANDTHE8WILL
bank to the left.
-OVETHE$IRECTION#ONTROLRIGHTANDTHE8
will bank to the right.
3/4 CHANNEL SELECT
X09 allows you to control your Quadrocopter in 3 channel mode
(beginner) or 4 channel mode (advanced flying). The X09 default
setting is 4 channel mode.
To change to 3 channel mode:
PRESS the Throttle Control stick vertically down then release, you will
hear 3 short beeps indicating the X09 now is set to 3CH mode.
To change back to 4 Channel mode:
PRESS the Throttle Control stick vertically down then release again,
you will hear 4 short beeps indicating the X09 is now set to 4CH
mode.
7 8
4 CHANNEL FLIGHT CONTROL
Move the Throttle up to increase the speed of
the motors and the X09 will rise up.
Move the Throttle down to decrease the speed of
the motors and the X09 will descend.
Move the Throttle stick left and the X09 will
rotate left.
Move the Throttle stick right and the X09 will
rotate right.
-OVETHE$
irection Control up and the
X09 will
move forward.
-OVETHE$IRECTION#ONTROLDOWNANDTHE8
will move backward.
X09 WARNING
:
4HE8ISDESIGNEDFOR).$//2AND/54$//2USEThe X09 blades revolve at high speeds and can cause damage to
the user, spectators and animals. Stand away from the X09 to reduce the risk of getting into the flight path. Warn spectators
that you will be flying your X09 so that they are aware of its position. Before flight, inspect the rotor blades to make certain
that the blades are securely fastened to the X09.
WARNING!
s#HOKING#UTTING(AZARD3MALL0ARTS3HARP2OTOR"LADES
s+EEPHANDSHAIRANDLOOSECLOTHINGAWAYFROMTHEPROPELLERWHENTHEPOWERSWITCHISTURNEDTOTHE/.POSITION
s4URNOFFTHETRANSMITTERAND8POWERSWITCHESWHENNOTINUSE
s4HEINCLUDEDCHARGERISBUILTSPECIFICALLYFORTHE8,I0OLYBATTERY$ONOTUSEITTOCHARGEANYOTHERBATTERY
s.EWALKALINEBATTERIESARERECOMMENDEDFORMAXIMUMPERFORMANCE
s0ARENTALSUPERVISIONRECOMMENDEDWHENFLYING8
BATTERY WARNINGS
RECHARGEABLE BATTERY:
This X09 uses a Li-Poly rechargeable battery. If battery no longer stays charged, dispose of battery properly according to
local disposal requirements.
CONTROLLER BATTERIES:
Remote control requires 2 “AAA” batteries (not included). Please read the important battery safety warning below.
s$ONOTMIXALKALINESTANDARDCARBONZINCANDRECHARGEABLEBATTERIESNICKELMETALHYDRIDE
s$ONOTMIXOLDANDNEWBATTERIES
s.ONRECHARGEABLEBATTERIESARENOTTOBERECHARGED
s2ECHARGEABLEBATTERIESARETOBEREMOVEDFROMTHEITEMBEFOREBEINGCHARGEDIFREMOVABLE
s2ECHARGEABLEBATTERIESAREONLYTOBECHARGEDUNDERADULTSUPERVISION
s%XHAUSTEDBATTERIESSHOULDBEREMOVEDIMMEDIATELYANDMUSTBERECYCLEDORDISPOSEDOFPROPERLY
according to state or local government ordinances and regulations.
s4HESUPPLYTERMINALSARENOTTOBESHORTCIRCUITED
s/NLYBATTERIESOFTHESAMEOREQUIVALENTTYPEASRECOMMENDEDARETOBEUSED
s"ATTERIESARETOBEINSERTEDWITHTHECORRECTPOLARITYSEEINSIDEBOOKLETFORDIAGRAM
s$ONOTDISPOSEOFBATTERIESINAFIREBATTERIESMAYLEAKOREXPLODE
CARE AND MAINTENANCE
sAlways remove the batteries from the wireless infrared remote control when it is not being used for an extended period
of time.
s4OCLEANGENTLYWIPETHEREMOTECONTROLAND8WITHACLEANDAMPCLOTH
s+EEPTHETOYAWAYFROMDIRECTHEATORSUNLIGHT
s$ONOTSUBMERGETHETOYINTOWATER4HISCANDAMAGETHEUNITBEYONDREPAIR
s0ARENTALGUIDANCERECOMMENDEDWHENINSTALLINGORREPLACINGTHEBATTERIES
HOW TO DO 360º STUNT ROLLS
)NORDERTOMAKEYOUR8DOROLLSYOUMUSTFULLYCHARGEYOURBATTERY  
.OTE4HE8WILLNOTDOSTUNTROLLSIN-ODEORUNDERLOWBATTERYINDICATION4HE,%$LIGHTSON
the drone will be flashing).
/NCEYOUAREREADYTOATTEMPTAROLLSIMPLYDEPRESSANDLETGOOFTHE345.4BUTTONONTHETOP
 RIGHTHANDSIDEOFYOURCONTROLLERSEE2EMOTE$IAGRAMONPAGE9OUWILLHEARBEEPINGSOUNDSTHIS
 MEANSYOUARENOWINh345.4-/$%
3. Now quickly move your right control stick in any of 4 directions; up, down, left or right. Your X09
copter will instantly roll in the associated direction. See diagram below.
Note:
After performed the stunt roll, the beeping sounds will stop. Repeat step 2 to 3 if you wish to do it
again.
If the X09 becomes unstable during the course
of flying, you may need to calibrate the internal
gyros. To do this place the X09 on a flat level
SURFACE4HE,%$SONTHEX09 will flash quickly
and then remain solid, this indicates your drone
has been recalibrated (see diagram E).
REPLACING THE PROPELLER BLADE
Your X09 propeller system is a precision instrument that may need repair or replacement from time to
time for optimal flight function. Crash landing from high-speed aerial flights may cause damage to
your X09 propellers.
1. X09 has four blades, two gray propellers on the front and two black propellers on the back.
2. When taking off the damaged blade, always use the included blade wrench. Refer to the instruction
diagrams below. Always use mild force, be gentle!
3. When replacing the new blades, make sure to match the indicating letter embossed on the blades to
the diagram below.
Rear
Front
A
A
B
B
910
F
360˚Stunt Roll
G
CALIBRATING THE X09
Blade Front Left = A
Blade Front Right = B
Blade Rear Left = B
Blade Rear Right = A
E

Navigation menu