Asian Express PL1480 SpyderX User Manual Propel Drone Spyder X IM 0403 v4 old

Asian Express Holding Ltd SpyderX Propel Drone Spyder X IM 0403 v4 old

User manual.pdf

FCC Part 15 NoticeMade in ChinaConforms to safety requirements of ASTM, CPSIA and FCC. ©2015 Rooftop Brands™ All rights reserved Tel: + (1) 949-566-9573 • www.propelrc.com CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or experienced radio/TV technician for help.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation.CHOKING HAZARD - Small parts. Not suitable for children under 3 years.WARNING!WARNING: Never leave product charging unattended for extended periods of time. Always disconnect Spyder XTM from charger immediately after the Spyder XTM is fully charged. Please refer to enclosed safety instructions.INSTRUCTION BOOKLETColors and styles may slightly vary.PACKAGE CONTAINS:2.4G Wireless Controller Instruction ManualSpare Parts USB charging cordSpyder XTMSPYDER XTMPalm Sized High Performance "Stunt" Drone
1.5VAA1.5VAA1.5VAA1.5VAA1.5VAA1.5VAAA BD6 1.5 volt “AA” Alkaline Batteries1 2TABLE OF CONTENTSProduct Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Remote Control Battery Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Charging Your Spyder X™ Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Spyder X™ Quadrocopter Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Remote Control Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Flight Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Syncing Your Spyder X™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Flying Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Recognizing The Front & Back Of The Spyder X™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Channel Flight Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Adjusting Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Level Surface Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Flight Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Flight Practice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Performing A 360º Stunt Flip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Replacing The Propeller Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Battery Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Thank you for purchasing the Spyder X™ 2.4 Ghz Quadrocopter. Please read this instruction booklet as it contains valuable information on how to properly fly and care for your Spyder X™ Drone.FEATURES• 6 axis gyro high-speed aircraft for incredible maneuvers including 360º aerial stunts!• Built-in 6axis gyro chip for extremely stable flight and maneuverability.• 2.4 Ghz, remote allows flight range up to 300 feet and multiple player use.REMOTE CONTROL BATTERY INSTALLATION1. Remove the battery cover from the back of the controller as shown in diagram A.2. Install 6 “AA” fresh alkaline batteries into the controller as shown in diagram B. Make sure to install batteries to their correct polarity. Do not mix old and new batteries or battery types.3. Replace the battery cover.CHARGING YOUR SPYDER X™ BATTERY1. Turn the Spyder X™ over and carefully remove the battery (see diagram C). 2. Connect the battery to the female connector end of the USB cable. Connect the universal end of the USB cable. to your computer’s USB port (see diagram D). CAUTION: improper connection may damage the Spyder X™.3. Average charging time is 70 minutes, RED LED indicator goes off when charging and will turn RED when battery is fully charged. A full charge will allow for about 5-6 minutes of flight time depending on environment and user input.IMPORTANT: ALWAYS REMEMBER TO UNPLUG YOUR CHARGING CORD WHEN NOT IN USE!Universal USB Charging CableC
SPYDER X™ QUADROCOPTER DIAGRAMSPYDER X™ REMOTE DIAGRAMSpeed SettingThrottle TrimAdjustmentThrottle & SpinLeft/RightRight/Left SpinTrim AdjustmentPower SwitchPower IndicatorAntenna360º Flip ButtonForward/BackwardBank Left/RightForward/BackwardTrim AdjustmentBank Right/Left TrimAdjustmentE3 4FLIGHT PREPARATION• Verify that there are 6 “AA” batteries inside the remote control unit and the Spyder X™ has been fully charged.• Make sure your Spyder X™ and controller are both turned on. • Make sure to be in a large space with an open radius of at least 100 feet. • Make sure the empty space has no obstacles. Set your Spyder X™ on a clean flat surface before take-off.DO NOT ATTEMPT TO FLY YOUR SPYDER X™ IF THERE IS RAIN, SNOW, HEAVY WINDS, THUNDER OR LIGHTNING OUTDOORS. IT COULD DAMAGE YOUR PRODUCT AND POSSIBLY EVEN CAUSE BODILY HARM.SYNCING YOUR SPYDER X™Important! When syncing your SPYDER X™ quadrocopter with the controller always make sure that the quadrocopter is on a flat level surface and that your digital trim settings are in the center position. This insures that the 6 Axis gyro is properly programmed to mimic your trim settings. Your Spyder X™ utilizes an automatic 2.4G channel selection system that allows up to 8 people to fly side by side in the same wireless range with no interference.Syncing your aircraft:1. Before starting, make sure that the power on your controller is in the OFF position and the Spyder X™ wire leads are not connected. Make sure that there are no other 2.4G devices in the area as well .2. Connect the battery wire lead to the Spyder X™ lead and set it down on a flat surface. The LED indicator lights of the Spyder X™ should begin to flash (see diagram E).3. Turn ON the remote, you will hear a beep, the Spyder X™’s flashing LED lights should change to solid, push the throttle on the left all the way forward and then slowly pull the throttle all the way back. You will hear 2 beeps and your controller should now have a solid red light. If not , repeat the above steps.FLYING TIPS• It is recommended that you operate the Spyder X™ in a wide space. The ideal space should have a 200 foot radius. • Parental guidance or adult supervision is suggested at all times.• If you are flying the Spyder X™ with others, make sure all spectators are behind you.• For best performance, it is recommended that you operate the Spyder X™ in zero wind conditions. Wind can greatly affect the performance of the aircraft or cause injury.DO NOT FLY YOUR SPYDER X™ IN FOUL WEATHER!WARNINGPropeller Guard Propeller BladeLi-Poly Battery CompartmentLanding Gear
O5 6Forward/Backward Trim• If your Spyder X™ drifts forward, push and release the BACKWARD TRIM button back repeatedly until the motion stops and proper flight is maintained (see diagram K). • If your Spyder X™ drifts backwards, push and release the FORWARD TRIM button forward in the same manner until the problem is resolved.Right/Left Trim• If your Spyder X™ drifts left, push and release the RIGHT TRIM button back repeatedly until the motion stops and proper flight is maintained (see diagram L). • If your Spyder X™ drifts right, push and release the LEFT TRIM button in the same manner until the problem is resolved.Right/Left Spin Trim• If your Spyder X™ spins left, push and release the RIGHT SPIN TRIM button back repeatedly until the motion stops and proper flight is maintained (see diagram M). • If your Spyder X™ spins right, push and release the LEFT SPIN TRIM button in the same manner until the problem is resolved (see diagram N).LEVEL SURFACE CALIBRATIONIf the aircraft becomes unstable during the course of flying, you may need to restabilize the internal gyros.To do this place the Spyder X™ on a level surface, SET THE SPEED SETTING TO 100% (you will hear three beeps)then pull both of the control levers on the remote down and to the left (approximately 45º) at the same time. The LEDs on the Spyder X™ will flash quickly and then remain solid, this indicates your aircraft has been stabilized (see diagram O). SPEED SELECT BUTTONThe Spyder X™ has 3 speed settings; SLOW (40%), MEDIUM (70%) and HIGH (100%). The Default setting when you first turn on your Spyder X™ is the SLOW (40%) speed mode. Change the speed to MEDIUM you simply press the Speed setting button (see remote diagram on pg 3) you will hear two beeps that means your Spyder X™ speed on MEIDIUM (70%) setting. Change the speed to HIGH (100%) you press the Speed setting button you will hear three beeps that mean your Spyder X™ speed on HIGH(100%) setting. You will be notice what speed you are on base on the beeps, one for SLOW, TWO for MEIUM, THREE for Hight. Speed settings can be set before flight or during the flight.4 CHANNEL FLIGHT CONTROLBelow is a list of basic flight functions for your long-range remote control Spyder X™. While learning to fly your Spyder X™ it is best to start with a large space until you get used to the basic controls. As you master flying your Spyder X™ you can move to more advanced maneuvering techniques. Practice makesa perfect! When you have these basic steps down you can move to the next level.Move the left Throttle stick up to increase the speed and the Spyder X™ will accelerate and ascend. Move the left Throttle stick down to decrease the speed and the Spyder X™ will decelerate and descend (see diagram G).Move the left Throttle stick left and the Spyder X™ will rotate left.Move the left Throttle stick right and the Spyder X™ will rotate right (see diagram H).Move the right Direction Stick up while in flight and the Spyder X™ will move forward.Move the right Direction Control down while in flight and the Spyder X™ will move backward (see diagram I).Move the right Direction Control left and the Spyder X™ will bank to the left.Move the right Direction Control right and the Spyder X™ will bank to the right (see diagram J).RECOGNIZING THE FRONT & BACK OF THE SPYDER X™Even though the Spyder X™ has four rotors there is still a front or "forward" facing direction and "back" or backwards facing direction. The front of the Quadrocopter displays BLUE LED lights and the back of the Quadrocopter displays RED LED lights when activated (see diagram F).ADJUSTING TRIM From time to time you may have to adjust the TRIM buttons to ensure theSpyder X™ will hover in mid-air and respond accurately to your commands.FFRONTREARGH I J FRONTKLMN
Fixed-point revolvingFixed-point landing Square Pattern Manuever Cross Pattern ManueverP1 P2 7 8FLIGHT PRACTICETo master flying your aircraft try practicing the excersizes shown below. Start with simple vertical takeoffs, landings, and left/right turning and rotating. Once those are mastered move on to square and cross maneuvers. Good luck and have fun!PERFORMING 360º STUNT FLIPSAfter you have mastered flying the Spyder X™ you are ready to try flips. Once the Spyder X™ is hovering at least 3 meters (about 10 feet) off the ground trigger the 360) Flip Button (see diagram P1) and push the right lever forward slightly and let go. The Spyder X™ will instantly perform a forward flip. To perform a backwards or side flip press and hold the 360º Flip Button and push the right lever in the direction you wish to flip just as you did for the forward flip (see diagram P2 & P3). PROBLEM POSSIBLE REASON SOLUTION 1. Power switched off 1. Switch the ON/OFF switch to ON No Power 2. Polarity is reversed 2. Make sure all batteries are installed correctly (see diagram B) 3. Batteries may be dead 3. Replace batteries 1. Remote is switched off 1. Switch the ON/OFF switch to ON Remote Not 2. Spyder X™ battery is not connected 2. Switch the ON/OFF switch to ON Responding 3. Too windy 3. Windy conditions severely impair the operation of the Spyder X™ 4. The remote is not synced 4. Re-sync the remote Aircraft Won’t 1. Rotor speed too slow 1. Push throttle lever forward lift off 2. Aircraft not fully charged 2. Recharge your Spyder X™ Aircraft Descends 1. Moving the throttle too quickly 1. Control the throttle slower and Too Fast smoother Aircraft Not 1. Gyroscopes not functioning 1. Turn of the Spyder X™ and Responding Reset the Gyro (see diagram L) Loss of Spyder X™ 1. Aircraft is out of range of remote 1. Keep the aircraft within a 300 Control Feet radius of the remoteTROUBLESHOOTING YOUR SPYDER X™Flip ForwardFlip Right Flip LeftFlip BackwardP3
910SPYDER X™ WARNING:The Spyder X™ is designed for INDOOR or OUTDOOR. Spyder X™ blades revolve at high speeds and can cause damage to the user, spectators and animals. Stand away from the Spyder X™ to reduce the risk of getting into the flight path. Warn spectators that you will be flying your Spyder X™ so that they are aware of its position. Before flight, inspect the rotor blades to make certain that the blades are securely fastened to the Spyder X™.WARNING!• Choking/Cutting Hazard. Small Parts/Sharp Rotor Blades.• Keep hands, hair and loose clothing away from the propeller when the power switch is turned to the ON position.• Turn off the transmitter and Spyder X™ power switches when not in use.• The included charger is built specifically for the Spyder X™ Li-Poly battery. Do not use it to charge any other battery.• New alkaline batteries are recommended for maximum performance.• Parental supervision recommended when flying Spyder X™.BATTERY WARNINGSRECHARGEABLE BATTERY:This Spyder X™ uses a Li-Poly rechargeable battery. If battery no longer stays charged, dispose of battery properly according to local disposal requirements.CONTROLLER BATTERIES:Remote control requires 6 “AA” batteries (not included). Please read the important battery safety warning below.• Do not mix alkaline, standard (carbon-zinc) and rechargeable batteries (Nickel Metal Hydride).• Do not mix old and new batteries.• Non-rechargeable batteries are not to be recharged.• Rechargeable batteries are to be removed from the item before being charged (if removable).• Rechargeable batteries are only to be charged under adult supervision.• Exhausted batteries should be removed immediately and must be recycled or disposed of properly according to state or local government ordinances and regulations.• The supply terminals are not to be short-circuited.• Only batteries of the same or equivalent type as recommended are to be used.• Batteries are to be inserted with the correct polarity (see inside booklet for diagram).• Do not dispose batteries in a fire - batteries may leak or explode.CARE AND MAINTENANCE• Always remove the batteries from the wireless remote control when it is not being used for an extended period of time.• To clean, gently wipe the remote control and Spyder X™ with a clean damp cloth.• Keep the toy away from direct heat or sunlight.• Do not submerge the toy into water. This can damage the unit beyond repair.• Parental guidance recommended when installing or replacing the batteries.REPLACING THE PROPELLER BLADESYour Spyder X™ propeller system is a precision instrument that may need repair or replacement from time to time for optimal flight function. Crash landing from high-speed aerial flights may cause damage to your Spyder X™ propellers.1. Spyder X™ have four blades, two on the front, and two on the back. Always disconnect the battery before replacing the propeller blades. Please note that the blades and the Spyder X™ are labeled with an embossed A or B (see diagram Q ).2. When replacing the propeller blades, gently remove the blade from the rotor shaft. 3. Replace the damaged blade with the correct blade. Make sure to match the indication letter on the blade with the letter on the aircraft as shown in diagram Q.FRONTREARBAABDiagram Q

Navigation menu