Asian Express VL-3570C Cloud Force+WIFI/X14 Galactic X+WIFI User Manual

Asian Express Holdings Limited Cloud Force+WIFI/X14 Galactic X+WIFI

User Manual

Download: Asian Express VL-3570C Cloud Force+WIFI/X14 Galactic X+WIFI User Manual
Mirror Download [FCC.gov]Asian Express VL-3570C Cloud Force+WIFI/X14 Galactic X+WIFI User Manual
Document ID3502444
Application IDNd9/P+rvCNvTV1pgcX4MyA==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize339.05kB (4238097 bits)
Date Submitted2017-08-09 00:00:00
Date Available2017-08-09 00:00:00
Creation Date2017-07-31 15:24:43
Producing SoftwareAdobe Acrobat 10.1.1 Image Conversion Plug-in
Document Lastmod2017-07-31 15:30:06
Document TitleUser Manual
Document CreatorAdobe Acrobat 10.1.1

FCC Part 15 C Notice
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the
user‘s authority to operate the equipment. _
NOTE:This oipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a
residential installation.This e uipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance witht e instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception,which can be determined by turning the equipment off and on, the user is
encouraged to tr to correct the interference by one or more of the following measures:
Reorient or re ocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or experienced rad iof TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
[I] This device may not cause harmful interferenceand _ _ _ .
[2] this devrce must accept any Interference received, including interference that may cause undesued operation.
|C_Radiation Exposure Statement: . _ _ _ .
This uiprnent complies With IC radiation exposure limits set forth for an uncontrolled envrronment.This equipment
shou be installed and operated With minimum distance 20cm between the radiator& your body.
Declaration d'exposition aux radiations:
Cet équipement est conforme aux Iimites d'expositjon aux rayonnements IC etablies pour un environneme nt non
controle.Cet eqmpement doit etre i nstalle et utilise avec un minimum de 20 cm de distance entre la source de
rayonnement et votre corps.
INDUSTRY CANADA NOTICE: CANADA ONLY.
This device complies with Industry Canada licence—exem pt RSS standardfsmperation is subject to the following
two conditions: (1] this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est confon'ne aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes :(1) I'appareil ne doit pas produire de brouillage,et {2)
I'utilisateurde I'appareil doit accepter dout brouillage radioélectrique subi, méme si Ie brouillage est susceptible
d'en compromettre Ie fonctionnement.
CAN ICES-3 (B)INMB-3(B)
This product meets the applicable Innovation, Science and Economic Development Canada technical
specifications.
Ce produit répond aux spécifications techniques pertinentes d'lnnovation,Science et Développement
economique applicables
ms DLASBCB:
& WARNING!
crowns HAZARD - Small pans. "swims Speed Class 6 «New mlcroSD or
Mmi‘bleford‘inmmoeram. rriicroSDHCard (not ham
IliDmSflHl: logo is a nutrient 0780-36, IJG.
Conforms to safety requirements of FCC, RSSZIO and R8824? .
©2017 Rooftop BrandsTM All rights reserved Made in China
Te|:+ (1)949—566—9573- www.propelrc.com v1.0
GALACT IC
OUTDOOR STREAMING DRONE
INSTRUCTION BOOKLET
WARNING: Never leave product charging unattended for extended periods of
time. AhNays disconnect the battery from charger immediately after the battery
is fully charged. Please refer to enclosed safety instructions.
PACKAGE CONTAINS:
Galactic X 2.46 Wireless Controller Spare Parts
Colors and styles may vary slightly.
USB Charger
8. Li—Poly
Rechargeable Battery
Phone Holder
iilé-
Instruction Manual
PROPEL
TABLE OF CONTENTS
Features .......... 2
Remote Control Battery Installation ........................................ 2
Charging the Galactic X's Li—Poly Battery .................................... 2
Galactic X Battery Installation And Removal ................................. 2
Galactic X Diagram .............. . .......... . ............................ 3
Control Diagram ........................................................ 3
Flight Preparation ....................................................... 4
Syncing Your Galactic X .................................................. 4
Now You Are Ready To Fly ................................................ 5
Recognizing The Front 8: Rear of The Galactic X .............................. 5
Startinngtopping The Rotors ............................................. 5
Manual Start/stop ....................................................... 5
Auto Start/Land ......................................................... 5
Understanding The Altitude Lock Sensor .................................... 6
Speed Select Button ..................................................... 6
Headless Mode Button ........................... . ...................... 6
Flight Control .......................................................... 7
Flight Practice .......................................................... 7
Adjusting The Trim ...................................................... 8
Calibrating The Galactic X ................................................ 8
How To Perform 360° Stunt Rolls .......................................... 9
Live Video Streaming .................................................... 10
Operating The Camera ................................................... 10
Propel Galactic X WiFi APP Installation ..................................... 1 1
Pairing Galactic X to Your Compatible Device ................................ 11
Quick Start ............................................................. 12
Detailed APP Overview ................................................... 12
Troubleshooting Your Galactic X ........................................... 13
Replacing The Propeller Blades ............................................ 13
Warnings .............................................................. 14
Battery Warnings ....................................................... 14
Care and Maintenance ................................................... 14
FCC Information ........................................................ 15
Thank you for purchasing the Galactic X‘" 2.4 Ghz High—Performance Stunt Drone. Please read this
instruction booklet as it contains valuable information on how to properly fly and care for your Galactic X1".
4EATUR
rde range rgital radio allows flight range up to 150 feet!
- 6 axis gyro for extremely stable flight and maneuverability.
- Push button 360° aeria stunts.
- On—board camera records videos and still photos to your mobile devices.
- 2 speed settings for beginner to more skilled pilots.
- Additional replacement parts included.
REMOTE CONTROL BATTERY INSTALLATION
1. Unscrew the security screw and remove the battery cover from the back of the controller.
2. Install 6”AA" alkaline batteries into the controller as a
shown in diagram A.
3. Replace the battery cover and replace the security screw.
4. Turn over the controller and turn the ONIOFF switch to the On
figsmon. If the LED IIghts turns on you have Installed your
tterles properly.
CHARGING THE GALACTIC X’S Ll-POLY BATTERY tam-Am
1. Connect the battery to the battery charger as showntsee diagram B). (not indudedl
Caution: l'he USBplug fits the charging socketonly in one way. Do notforce it.
2. Next, connect the USB charger to your computer's USB port(see diagram C ).
Commilyrnethischargerwr'thampmgUSBpordDonotottanpttomotherllSBdrorgingdevices.
3. The red LED on the USB plug lights off when charging is complete [see diagram D).
Note: If thered LED lights off, eitherthe drarging is complete orthe ”58 play isnotproperlyconnetted
4. Average charging time is approximately 120 minutes.A fully charged drone can fly for
approximately 56 minutes depending on environment and user input.
The red LED on the USB
plug lights off when
(harglng Is . mplete
IMPORMNEALWAYS REMEMBER T0 UNPLUG YOUR CHARGING CORD WHEN NOT IN USE!
GALACTIC X BATTERY INSTALLATION AND REMOVAL
1. Open the Galactic X's battery compartrnent.Then slide the battery in and close the battery compartment
coverlsee diagram E).
Contion:lalalre sure the arrow and polaritymarlrings are facing up! Your Galactic)! will not work with impoper
botteryinstallation.
2. Turn on the ONIOFF switch of the Galactic X, the LED lights should startflashing if you have installed the
battery properly.
3. To remove the battery out from the battery compartment, you need first push the battery lock up and then
pull the battery out. Please see the diagram E below.
Arrow facing up
GALACTIC X DIAGRAM
Front (White light)
Landing Gear
Digital Camera
Power 0n/ Off
Camera Line Interface
CONTROLLER DIAGRAM
Camera
Throttle
Forward Trim
Backward Trim
Power Indicator
Start/Stop
Battery Compartment
Bottom View
Stunt Button
Direction Control
Speed
Headless Mode
Rig ht Trim
LeftTrim
Battle Indicator
Power 0n/0ff
WARNING
DO NOT FLY YOUR GALACTIC x IN FOUL WEATHER!
eoee
FLIGHT PREPARATION
- Verify that there are 6”AA"batteries installed the remote control unit and the Galactic X battery has been
fully charged.
- Make sure to be in a large open space preferably a field or a park with an open radius of at least 200 feet.
- Make sure to start your drone on a clean flat level surface before take-off.
- IMPORTANT! Until you have experience in flying your Galactic X, it is not advised to use in any rate of
wind.Wait u ntil a zero wind day or extremely light wind when learning how to fly.
SYNCING YOUR GALACTIC X
Important! When syncing your Galactic X with the controller always make sure that the drone is on a
flat level surface and that your digital trim settings are in the center position.This insures that the 6
axis gyro is properly programmed to respond to your trim settings.Your Galactic X utilizes an
automatic 2.4G channel selection system that allows up to 8 people to fly side by side in the same wireless
range with no interference.
1. Before starting, make sure that the power switch is off both on your controller and the Galactic X. Make
sure that there are no other 2.4G devices in the area.
2. Tum on your Galactic X and set it down on any fiat surface.The red and white LED lights ofthe drone should
begin to flash repeatedly.
3.0uickly turn on the remote and you will hear 2 beeping sounds and also may notice the power indicator
flashedaaupleoftimes.
4. Push the left control stick all the way up until it stops and then pull it back all the way down to the
bottom(see diagram below).You should hear 2 high-pitched beeps and notice the lights on the drone
should become solid. If the lights on both the drone and the controller have become solid you have
successfully synced your Galactic X and are ready to fly. If the lights on the controller or the drone are still
flashing repeat steps H again.
- TIP 1: try not to leave too much time between turning on the drone and the
controller or your syncing window will time-out.
° TIP 2: Syncing your drone indoors or in the shade will make it easier to see the LED
light indicators on both the controller and the drone.
7 III}
=J
move thelctcly1ntrol stack all the way the flashin dredhLED light will
llllloallld l'lear gyveg’ own you syellge e so I w en you are
NOW YOU ARE READY TO FLY!
If you have successfully lysynced your Galactic X to your controller as explained on page 4 you are now ready
to fly .Before beginning to fly your drone you should familiarize yourself with how the controls work so
please carefully read and familiarize yourself with various control features explain in the next two pages.
Once again as a beginner pilot you should learn how to control your drone in a large open field or park on a
day with zero or very light wind. Do not try to fly your Galactic X too high until you become a more
experience pilot.
RECOGNIZING THE FRONT 8: REAR OF THE GALACTIC X
Even though the Galactic X has four rotors there is still a front or "forward" facing direction and "rear“ or
backwards facing direction.The forward from and forward facing direction of the Galactic X is the side with
camera(see diagram G ).The rear and badiward facing direction of the Quadrocopter is the side with
battery compartmentlsee diagram G).
HOTE:The front of the Quadrocopter also displays WHITE lED light and the back ofthe Quadrocopter displays
RED LED lights.
STARTING/STOPPING THE ROTORS
Note:You can start/stop your GalacticX manually or automatically.
Please follow one of the steps below to operate accordingly. Make sure you have
properly synced the Galactic X and the power stays on.
MAN UAL START! STOP
- To start the rotors simply move the two control stidrs both down and
out (see diagram), hold until the rotors start spinning. Now release
both sticks to the neutral position and push the throttle up to take off.
- To stop the rotors,alter starting them you can simply wait about 10
seconds, and they will stop automatically. 0r move both stidis down
and out again to stop immediately. After take off, you can simply
pull the throttle all the way down and hold till the rotors stop .
AUTO STA RT/ LAND
The Galactic X has an auto start/land feature whidI allows you to
start/land automatically. Simply press the START/STOP button on
the top of the controller and your Galactic X will begin taking
off/landinglsee diagram below).
NOTE: You can still control the direction while auto starting/landing
to avoid obstacles.
U N DERSTANDING THE ALTITUDE LOCK SENSOR
The Galactic X has a unique Altitude Lock function, air pressure sensor that allows for easier flight control
and stability .A beginner's friend, it allows the user to ease into piloting the copter. The sensor locks In the
altitude of the copter while allowing the user to adjust the directional controls without having to hold the
throttle. lifter starting the copter,fly it upwards to a safe height. Once at a safe height, release the throttle to
the neutral position. Now your Galactic X should be locked in the altitude and you can focus on getting used
to the directional controls ofthe Galactic X.The copter always tends to self correct and go back to the last
locked height after moved up or down by outside forces.
Note:The altitude sensor does have some tolerance based on atmospheric conditions and could have a
slight variation in altitude.
SPEED SELECT BUTTON
The Galactic X has 2 speed settings; SLOW and HIGH. The Default setting when you first turn on your
Galactic X is the SLOW speed mode.To increase the speed simply trigger the Speed setting button (see
remote diagram on pg 3) you will hear 2 beeps and the speed changed to HIGH speed. Speed settings can be
set before flight or during the flight.
HEADLESS MODE BUTTON
You can maintain orientation of your Galactic X during flight.
1. Set the Galactic X on a flat level surface in front of you,front side straight ahead, press the headless
mode button to activate the internal compass.
2. You'll hear a continuous beeping sounds reminding that you're flying in"Headless Mode‘fAlso the lights
on the drone will keep flashing.
Note: You need stay the same location when you activavted the headless mode, the Galactic! will exit
headless mode when you move.
FCC RF exposure statements
This Transmitter must not be co - lomted or operating in conjunction with any
other antenna or transmitter.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
mininum distance of 20 centimeters between the radiator and your body or nearby
persons.
IC Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Declaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnernents IC
établies pour un environnement non controlé. Cet équipement doit étre installé et
utilise avec un minimun de 20 cm de distance entre la source de rayonnement et
votre corps.
FLIGHT CONTROL
Below is a list of basic flight functions for your long-range remote to control the Galactic X.While
learning to fly your Galactic X it is best to start in a large space until you get used to the basic controls. As
you master flying your Galactic X you can move to more advanced maneuvering techniques. Practice
makes perfect!
Move the left Throttle stick up to increase the
propeller speed and the Galactic X will accelerate
and ascend.
Move the left Throttle stick down to decrease the
propeller speed and the Galactic X will decelerate
and descend (see diagram H).
While in the air, move the left Throttle stidr left
and the Galactic X will rotate left.
Move the left Throttle stick right and the
Galactic X will rotate right (see diagram l).
While in the air, move the right Direction Stick up
and the Galactic X will move forward.
Move the right Direction Control down and the
Galactic X will move backward (see diagram J).
While in the air, movethe right Direction Control left
and the Galactic X will bank to the left.
Move the right Direction Control right and the
Galactic X will bank to the right (see diagram K).
FLIGHT PRACTICE
To master flying your aircraft try practicing the excersizes shown below. Start with simple vertical takeoffs,
landings,and leftlright turning and rotating. Once those are mastered move on to square and cross
ma neuvers.Good ludc and have fun!
a?
Cross Pattern Maneuver
Fixed-Point Landing Square Pattern Maneuver
ADJ USTI NG TH E TRIM
NOTEzThe Galactic X is already properly trimmed and calibrated right out of the box and should not require
any trim adjustments before flying. Some more experienced pilots may want to adjust trim settings for
their style of flying. After several crashes you may need to adjust trim settings for the Galactic X to be more
balanced.
Forward/Backward Trim
- If your Galactic X drifts forward while in the air,
push and release the BACKWARD TRIM button back
repeatedly until the motion stops and proper flight
is maintained {see diagram L). K
- If your Galactic X drifts backwards, push and release '
the FORWARDTRIM button forward in the same
manner until the problem is resolved.
Dank Right/Left Trim
- If your Galactic X drifts left while in the air, push .
and release the RIGHTTRIM button back repeatedly ,
until the motion stops and proper flight is
maintained (see diagram M).
- If your Galactic X drifts right, push and release the
LEFT TRIM button in the same manner until the
problem is resolved.
NOTEzThe use of the Trim buttons utilizes soundle single long Beep indicates the product is
center trimmed. Continuous long Deeps indicate the product is trimmed to the maximum on a
particular side.
CALIBRATING THE GALACTICX
NOTEzYour Galactic X comes ore-calibrated out of the box so you are ready to fly.
After several crashes and shock to your gyro sensors, you may notice that your drone is drifting and not
holding its center position as well as it used to.
This most likely means that you need to recalibrate the 6 axis gyro. Please follow the simple instructions
below.
1. Place the Galactic X on a flat level surface.
2. Make sure the Galactic X is on and that the controller is synced (refer to syncing pg 4.). Do not start
the blades. Instead move both the throttle and control stick down and to the right comers and hold them
there for about 5 seconds(See Diagram P}.You will see the lights on the drone rapidly flash and stop. Once
the lights stop flashing you have completed your calibration and are ready to fly!
TROUBLE SHOOTING: If you do not see the lights flash, turn off your controller take out the battery in the
drone and start again. Always make sure to put your battery in first, then turn on your controller. Push the
left throttle stick up all the way and then pull back down again.When you hear the beep the Galactic X is
synced to the controller and you are ready to calibrate.
HOW TO PERFORM 360° STUNT ROLLS
Performing 360° stunt rolls with the Galactic X is as easy as 1-2-3:
1. Hover the Galactic X in still position making sure that you have at least 5 feet of clearance above
and below the quadrocopter,.
2. Press and release the 360° stunt button and you will enter the stunt roll mode which is indicated by a
continuous beeping (see diagram 01).
3. Determine which direction you want it to flip and quickly push the right control stick in the direction
you want to flip your Galactic X (see diagram 02).
You have 4 choices a) Forward Roll, b) Backwards roll, c) Right side roll, d) Left side roll.
4. To exit the Stunt Roll mode,simply Press and release the button again.
NotezStunt roll is only for high speed level. After stunt roll,your drone may descend or ascend from the
original heightJust move your throttle up or down a bit to balance out.
360° Stunt Roll Button
.\
. \
_)
LIVE VIDEO STREAMING
Your Galactic X comes equipped with an onboard digital camera that takes both video and still photographs to your
mobile devices Now you can have hours of fun creating aerial photography and videos forfamily and friends.
WHAT YOU WILL NEED TO GET STARTED USING YOUR CAMERA
1. One Apple orAndriod phone* (not included)
2. Propel Galactic X APP installed (app store or Andriod market available)
PHONE HOLDERAND PHONE INSIJI [LATION
Put the phone holder hook la) and Hook (b) to the slots on the top of the controller,see the illustration
below, postion the metal locklc) to the bottom of the bar(d).Push the locker(e) to tigten the phone holder.
When you install the phone holder correctly you can use it to hold your phone (see diagram R)
OPERATING THE CAMERA
You can take in—flight photos or video with your Galactic X on board camera.
1. Ensure that the camera module is securely attached and locked onto the copter. Carefully insert a micro
SDHC card with a speed class of 6 or higher [not included) into the slot on the rear of the camera module.
Push in gently untilyou hear and feel a click. Now you are ready to use the camera.
2.To take still pictures, short press the camera button.The indicating LED light will flash one time.
3.To take video footage, hold down the camera button on the remote for a few seconds(see diagram V1).
You will hear a long beep and the indicating LED lights will start fiashing.To stop video footage
simply short press the button again.
4.Afterturning the Power Off on the copter,you may now remove the mircoSDHC card from the Galactic X
by gently pushing on the back of the card until you hear and feel a slight click.You may use the included
USB card reader to connect it to a computer and retrieve your pictures and video footage.
10
II
PROPEL GALACTIC X WiFi APP INSTALLATION
1.Make sure you are using a compatible AndroidTM orApple® iOS device.
2. Make sure your device has access to the internet.
3.For Apple® iOS devices, within the App Store,search and select " Propel Galactic XWiFi’.’ Hit the Install
button and the”Propel Galactic X WiFi" App should download and install automatically.
4. For AndroidTM OS devices,visit the Google Play store and search for"Propel Galactic X WiFiC’Selecting the
"Propel Galactic X WiFi”App will download the App and automatically install it on your device.
5. After the"Propel Galactic X WiFi" App is installed, it should create an icon on your screen. Click the”Prope|
Galactic X WiFi” icon to run the App to make sure that it has installed correctly on your device. If not,
please delete and repeat the process again.
PAIRING GALACTIC X TO YOUR COMPATIBLE DEVICE
1.After completely charging your Galactic X battery,install the battery to your Galactic Xlrefer to the user
ma nual).
2. In the Settings menu of your device, locate the Wi—Fi option.
3.Turn ON the Wi—Fi option.
4. Select”Propel Galactic X”from theWi-Fi |ist.Wait for your Galactic X to be connected. Return to the Main Menu.
( ‘ A . Wi-Fi Selfings
WITH Airplane Morse
I / Ga‘actrcx H ? i E
,H, l amzoom Propel Galactic XWiFi
Wm? H .. Cellular
Note: Apple® devices require the use of iOS 7.0 or higher.
ANDFIOIDTM devices require the use of OS 4.2.2 or higher.
QUICK START
1.When you install the App correctly and have paired to the drone successfully,you can hit the "PPL
Galactic X wifi"App icon.Tap"STA T"on the bottom right hand side of the screen. You should see the
real-time video from your Galactic X's camera.
2.This App allows you to control your Galactic X to take photo or record video by your mobile device.
Notezall the photos and videos will storaged in your mobile device, you can review the photos and videos
on your mobile device by using this App.
DETAILED APP OVERVIEW
3. Please see images below for a detailed App overview. This overview is also available under the "HELP”
icon in the home screen of the App.
CONTROL INTERFACE
HOME PAGE
4. If you’ re still encountering difficulties please contact our customer service department at
+1.949.566.9573.
IMPORTANT NOTICE :You can not take photos and videos at the same time.When you are in video mode
your camera:I photo button is disabled. If you want to take photos you must first exit video mode.
12
TROUBLESHOOTING YOUR Galactic X
PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION
l.Power switdred off
2.Polarity is reversed
1. Switch the ONIDFF switch to ON
2. Make sure all batteries are installed
correctty (see diagram A on p92)
3. Replace batteries
No Power
3.Batteries maybe low or in need of dlarging
l.Remote is switched off
2.battery power in remote is too weak
3.The remote is not properly synced
4.0m of control range
1. Switch the ONIOFF switch to ON
2.(hange batteries in remote.
3. Resync the remote
4. Do not fly beyond SflDfeet
l.Rotor speed too slow
2.Drone not fully charged
3.0bstruction of rotors
1. Push throttle lever forward
2. Recharge your Galactic X
3.(heck rotors for hair or other obstructions
Moving the throttle down too quickly
flying in high wind or bad weather
(ontrol the throttle slower, use auto land
feature, Do notfly in bad weather
If you continue to encounter problems call our customers service line at (949) 566—9573 Ext 1 for assistance.
Front
REPLACING THE PROPELLER BLADES
Your Galactic X's propeller system is a precision instrument that
may need repair or replacement from time to time for optimal
flight function.Crash landing at high-speed may cause damage
to your Galactic X’s propellers.
l.The Galactic X has four blades, each marked with an
indication letter(see the diagram S).
2.When replacing the propeller blades,make sure to matdt to
the indication letter on the blade to the one on the drone
body.
3. Unscrew from the side,then pull out the damaged one from
the top.
4.lnsta|l the correct one, make sure to line up the hole on the
propeller to the one on the motor shaft.
Gray Blade Front Left = L
Gray Blade Front Right : Ft
Black Blade Back Left = R
Black Blade Back Right = L
NOTE :When install the new propeller, hold against the bottom of
motor shaft so the propeller can go all the way into the position.
13
Galactic X WARNING:
The Galactic X is designed for OUTDOOR use.The Galactic X's blades revolve at high speeds and can came
damage to the user, spectators and animals. Stand away from the Galactic X to reduce the risk of getting
into the flight path.Wam spectators that you will be flying your Galactic X so that they are aware of its
position. Before flight, inspect the rotor blades to make certain that the blades are securely fastened to the
Galactic X.
WARNING!
- Choking/Cutting Hazard. Small Parts/Sharp Rotor Blades.
- Keep hands, hair and loose clothing away from the propeller when the power switch is turned to the
ON position.
- Turn off the transmitter and Galactic X power switches when not in use.
- The included charger is built specifically for the Galactic X Li-Poly battery. Do not use it to dtarge
any other battery.
- New alkaline batteries are recommended for maximum performance.
- Parental supervision recommended when flying Galactic X.
BATTERY WARNINGS
RECH ARGEABLE BATTERY:
This Galactic X uses a Li-Poly rechargeable battery. If battery no longer stays charged,dispose of battery
properly according to local disposal requirements.
CONTROLLER BATTERIES:
Remote control requires 6"AA" batteries (not included).
Please read the important battery safety warning below.
- Do not mix alkaline, standard (carbon—zinc) and rechargeable batteries (Nickel Metal Hydride).
- Do not mix old and new batteries.
- Non—rechargeable batteries are not to be recharged.
- Rechargeable batteries are to be removed from the item before being charged (if removable).
‘ Rechargeable batteries are only to be charged under adult supervision.
° Exhausted batteries should be removed immediatelyand must be recycled or disposed of properly
according to state or local government ordinances and regulations.
- The supply terminals are not to be short-circuited.
- Only batteries of the same or equivalent type as recommended are to be used.
' Batteries are to be inserted with the correct polarity (see inside booklet for diagram).
- Do not dispose batteries in a fire — batteries may leak or explode.
CARE AND MAINTENANCE
- Always remove the batteries from the wireless remote control when it is not being used for an
extended period of time.
~To clean, gently wipe the remote control and Galactic X with a clean damp cloth.
- Keep the toy away from direct heat or sunlight.
- Do not submerge the toy into water.This can damage the unit beyond repair.
- Parental guidance recommended when installing or replacing the batteries.
14

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Create Date                     : 2017:07:31 15:24:43+08:00
Creator                         : Adobe Acrobat 10.1.1
Modify Date                     : 2017:07:31 15:30:06+08:00
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2017:07:31 15:30:06+08:00
Creator Tool                    : Adobe Acrobat 10.1.1
Format                          : application/pdf
Document ID                     : uuid:041a55ad-3a02-3b4f-ac4a-5237a284b3af
Instance ID                     : uuid:f26e8256-6d07-b24e-8e87-1c30658526c0
Producer                        : Adobe Acrobat 10.1.1 Image Conversion Plug-in
Page Count                      : 8
EXIF Metadata provided by EXIF.tools
FCC ID Filing: VLEVL-3570C

Navigation menu