Askey Computer WLL6540 802.11 b/g/n 2.4G Band 1T1R AP Module User Manual

Askey Computer Corp 802.11 b/g/n 2.4G Band 1T1R AP Module

User Manual

802.11 b/g/n 2.4G Band 1T1R AP Module WLL6540(RoHS) OEM Manual
802.11 b/g/n 2.4G Band 1T1R AP Module WLL6540(RoHS) 1. Product (module) photo 2. Module dimensions 3. Antenna info Part number: 2108517-1 Antenna type: stamped metal antenna Max Peak gain: 2.4 dBi
4. Feature: The WLL6540(RoHS) module integrates a 1T1R 802.11n WI-FI radio, 1-Port fast Ethernet PHY, USB2.0 host, I2S/PCM and 4 GPIO. This module embedded high performance process a CPU can process advanced applications effortlessly, such as routing, security and VoIP; and includes variety of applications, such as a USB port for accessing external storage. ◆Embedded MIPS24KEc（575/580MHz）with 64KB I-Cache and 32 KB D- Cache ◆1T1R 2.4GHz with 150Mbps PHY data rate ◆Legacy 802.11b/g and 802.11n modes，20/40MHz channel bandwidth ◆802.11v ◆1-port 10/100 FE PHY ◆Iot (Internet of Things) ◆Green AP/STA ◆16 Multiple BSSID ◆AES128/256-CBC ◆WEP64/128/, TKIP, AES, WPA, WPA2, WAPI ◆WPS: PBC, PIN ◆ Small size 34mm*28mm 5. How to use this module  Install application on IOT (Internet of Thing) device (eg. smartphone or notebook program)  Power up processor unit (WLL6540(RoHS) power source).  Scan for Wi-Fi network SSID (WLL6540(RoHS) as default SSID), connect to SSID, and input password. (End-user can change SSID/Password from the application program)  Launch application and follow program’s guide to link wireless data  For detail, please reference end-product’s user’s manual
6. Pin assignment:
USA - Federal Communications Commission (FCC) FCC Radiation Exposure Statement Interference Statement These devices comply with Part 15 of the FCC Rules. Operation of the devices is subject to the following two conditions: (1) The devices may not cause harmful interference, and (2) The devices must accept any interference that might cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If the equipment is not installed and used in accordance with the instructions, the equipment might cause harmful interference to radio communications. There is no guarantee, however, that such interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by taking one or more of the following measures:  Relocate this device.  Increase the separation between the device and the receiver.  Connect the device into an outlet on a circuit different from that of other electronics.  Consult the dealer or an experienced radio technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: H8N-WLL6540”. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
OEM integrators instruction 1. This module is restricted to installation in products for use only in mobile and fixed applications. 2. This module can only be used with a host antenna circuit trace layout design in strict compliance with the OEM instructions provided in this manual 3. The antenna circuit and layout must follow “WLL6540(RoHS) OEM board design guide” to design their own antenna circuit. Canada. Industry Canada (IC) This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC No. cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC authorization.
End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains transmitter module IC: 1353A-WLL6540”. Contient le module d'émission IC: 1353A-WLL6540 This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. CAN ICES-3 (*)/NMB-3(*) * Insert either “A” or “B” but not both to identify the applicable Class of ITE. The Country Code Selection feature is disabled for products marketed in the US/Canada Taiwan NCC Statement 以下警語適用台灣地區 1. 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 2. 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

Navigation menu