Askey Computer WLU6111 802.11b/g/n Module User Manual
Askey Computer Corp 802.11b/g/n Module
User Manual
ASKEY
802.11b/g/n Module
WLU6111-D69
OPERATION
MANUAL
DRAFT_V01
1. Description
WLU6111-D69 is an 802.11b/g/n module; the product is put into the printer to connect with
Wireless AP Router and user, while any user need to be printing any documents through
wireless, WLU6111-D69 is better choice for use.
The WLU6111 is intended to be installed by a system integrator, not the end-user.
2. Product Spec.
Host Interfaces USB2.0
Form factor USB Wireless module
Chipset Broadcom BCM4319
Operation Voltage 3.0VDC ~ 3.6VDC
Network Standards IEEE 802.11b/g/n
Modulation Techniques DBPSK, DQPSK, CCK, BPSK, QPSK, 16QAM, 64QAM
Modulation Technology OFDM, DSSS with proprietary operation at 65Mbps(max.) within 20MHz
(HT20)
Data Rate 802.11b: 11, 5.5, 2, 1 Mbps
802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps
HT20: 65 MHz (MCS7)
Network Architectures Infrastructure and Ad Hoc
Operating Frequencies 2.412 – 2.462 GHz
Antenna Type Fractal-Antenna
Operating Channels 802.11b: 11 for North America; 13 for Europe; 14 for Japan
802.11g: 11 for North America; 13 for Europe; 14 for Japan
(Operation is limited in firmware to meet national regulations, not
changeable by the user)
RF Output Power 802.11b: 17.0 dBm +/- 1.5 dBm
802.11g: 17.0 dBm +/- 1.5 dBm
802.11n: 14.0 dBm +/- 1.5 dBm
Receiver sensitivity
(PER < 10%)
802.11b: -85dBm @ 11Mbps and PER < 8%
802.11g: -70dBm @ 54Mbps and PER < 10%
802.11n: -68dBm @ MCS 7 B.W 20MHz and PER < 10%
Power Consumption TX: 330mA @ 1Mbps; 215mA@54Mbps; 250mA@MCS7
RX: 120mA
Security 1. WPATM (personal) and WPA2TM (personal) certified for powerful
encryption and authentication
2. AES and TKIP in hardware for faster data encryption and IEEE
802.11iTM Compatibility.
Software Support Windows® CE 5.0, Linux®, Windows® XP
Temperatures (AMBIENT) Operates from 0 to 70°C;
Storage from -40 to 70°C
Humidity
(non-condensing)
5 to 95 %
Unsupported operation WIN 98 and WIN ME
Manufacturer ID PID: BD 16
Product ID VID: 0A5C
3. Setup Operation
Please setup WLU6111-D69 into the printer, connect power cable from printer to power
jack of WLU6111-D69; power on the printer when you make sure WLU6111-D69 can be
supplier from printer, then you can see below setup window:
A. Install WLU6111-D69 into the system.
B. Press “No, not this time” as below window:
C. Press “Install from a list or specific location (Advanced)” as below window:
D. Press “Continue Anyway” as below window:
E. Press “Finish”, then you can connect with other wireless device through the
Wireless Module.
USA - Federal Communications Commission (FCC)
FCC Radiation Exposure Statement
CAUTION:
. • The radiated output power of WiFi Module 802.11bgn devices is far below the
FCC radio frequency exposure limits. Nevertheless, WiFi Module 802.11bgn devices
should be used in such a manner that the potential for human contact during normal
operation is minimized. To avoid the possibility of exceeding the FCC radio frequency
exposure limits, you should keep a distance of at least 20cm separation from antennas
in the Printer between you (or any other person in the vicinity) and the antenna
that is built into the notebook.
Interference Statement
These devices comply with Part 15 of the FCC Rules. Operation of the devices is subject to the
following two conditions: (1) The devices may not cause harmful interference, and (2) The
devices must accept any interference that might cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy. If the equipment is not installed and used in accordance with
the instructions, the equipment might cause harmful interference to radio communications.
There is no guarantee, however, that such interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception (which can be
determined by turning the equipment off and on), the user is encouraged to try to correct the
interference by taking one or more of the following measures:
. • Relocate this device.
. • Increase the separation between the device and the receiver.
. • Connect the device into an outlet on a circuit different from that of other electronics.
. • Consult the dealer or an experienced radio technician for help.
NOTE:
. • WiFi Module 802.11bgn must be installed and used in strict accordance with the
manufacturer's instructions as described in the user documentation that comes with the product.
Any other installation or use will violate FCC Part 15 regulations. Modifications not expressly
approved by ASKEY could void your authority to operate the equipment.
. • The devices must not be co-located or operating in conjunction with any other antenna
or transmitter.
Canada. Industry Canada (IC)
This device complies with RSS210 of Industry Canada.
CAUTION: Exposure to Radio Frequency Radiation. The installer of this radio equipment
must ensure that the antenna is located or pointed such that it does not emit RF field in excess of
Health Canada limits for the general population. Consult Safety Code 6, obtainable from health
Canada’s website www.hc-sc.ca/rpb.
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment.
3. Any changes or modifications (including the antennas) made to this device that are not
expressly approved by the manufacturer may void the user’s authority to operate the
equipment.
This device is intended only form OEM integrators under the following conditions:
1) The transmitter module may not be co-located with any other transmitter or antenna.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no longer
considered valid and the FCC ID can not be used on the final product. In these circumstances, the
OEM integrator will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate FCC authorization.
End Product Labeling
The final end product must be labeled in visible area with the following:
Contains TX FCC ID: H8N-WLU6111; IC: 1353A-WLU6111
End Product Manual Information
The user manual for end users must include the following information in a prominent location
"IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna
must not be co-located or operating in conjunction with any other antenna or transmitter.
Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.