User Manual
ATOMIC Quick Set-Up Guide Wireless Headphone system Model AWD204 0210ver2 Congratulations on the purchase of 900MHz Stereo RF Wireless Headphones to enjoy the revolutionary technology! Please check the supplied component against the following list: 1 x Transmitter 1 x Headphone 1 x Power Supply (AC/DC 12V200mA Adaptor for Transmitter) 1 x 3.5mm audio cord (built in) 1 x Charging Cord (built in) 2 x AAA NiMH550 mAH rechargeable battery FUNCTION KEYS HEADPHONES (1) Headbelt (2) Ear Cushion (3) Color LED Indicator (4) Power ON/OFF Switch (5) Volume Control Knob (6) Charging Socket (7) Battery Compartment (8) Battery cover (9) Tune 0210ver2 10 11 12 13 14 15 TRANSMITTER: Transmitter Front: (10) Charging LED Indicator (11) Power LED Indicator Transmitter Rear Side: (12) Charging Cord (13) Audio IN Cord (14) Switch for channel 1,2 and 3 (15) AC/DC Adaptor IN Socket ACCESSORIES: (16) AC/DC Adaptor 16 0210ver2 INSTALLATION Please follow this quick set-up guide to ensure trouble free installation of your headphones. Step 1: Connect the Stereo Audio Cord (13) to the audio output socket (i.e. PHONE/ HEADPHONE 3.5mm socket) of your audio source, e.g. TV, HiFi, CD, DVD player etc. *** If your audio source has 2 RCA output sockets (red and white in colour), use the 90mm Y-connection Cord ) (not included) for connection, if necessary. Step2: Connect one end of the AC/DC Adaptor (16) to the DC IN Socket (15) at the rear side of the transmitter, and the other end to the main electric wall outlet. Step3: The transmitter will be automatically ON (Green) when there is audio signal IN from the audio source (please make sure that the transmitter is powered on by the AC/DC adaptor in Step 2). Place the transmitter on a dry, cool place preferably above head level. *** The transmitter has auto-cut-off function. When there is no audio signal for over10 minutes, the transmitter will goes into deep sleep mode. TX can wake up immediately after it detects audio input again.. Step 4: Open the Battery Cover (8). Insert 2 pcs AAA size batteries into the Battery Compartment (7) at the Left hand side of the headphones observing the correct polarity. Then close the Battery Cover (8), and switch the headphones ON (4). Step 5: Switch on your music device (TV. HiFi, CD, DVD etc.) and start your media playing. Then headphone’s LED will be Green and music comes out. Step 6: Then you can hear a good quality sound. Adjust the Volume Control Knob (5) to a comfortable sound level. 0210ver2 CHARGING THE HEADPHONES Battery type: No. of cells: Rated capacity: Rechargeable batteries AAA 2pcs 550 mAH / 10 – 12 hrs Step 1: Insert 2 pcs AAA size rechargeable batteries into the Battery Compartment (7) at the Left hand side of the headphones. Step 2: Switch OFF (4) the headphones. Step 3: Connect the transmitter to a conveniently located electric wall outlet with the supplied AC/DC Adaptor (15). Step 4: Insert one end of the Charging Cord (12) to the Charging Socket (6) of headphones. The batteries should be charged for a full 12 hours. During charging process, the Charging LED Indicator (10) will glow RED the headphone is being charged. *** Regular (non-rechargeable type) batteries can also be used to operate this headphone. However, you must never attempt to charge non-rechargeable batteries in this appliance as this could prove dangerous. Only the supplied special battery can be charged. Step 5: When the batteries have been charged, remember to remove the Charging Cord from the headphones. *** Charging procedure should never exceed 48 hours. Caution! To avoid risk of fire or injury, do not attempt to recharge non-rechargeable batteries. Replace only with the same or equivalent type recommended by the manufacturer. Please dispose of old, defective batteries in an environmentally friendly manner in accordance with the relevant legislation Use only the supplied adaptor. Use of other adaptor may cause damage to the unit When not using the unit for a long period of time, remove all batteries from unit to avoid damage or battery leakage. Disconnect the adaptor from the wall outlet when the unit is not to be operated’ Symbol 0210ver2 indicating separate collection for electrical and electronic equipment. TROUBLE SHOOTING GUIDE If you encounter any trouble in setting up the Headphones, please check the following points: (1) Distorted sound quality or unclear sound: ~ Check if the sound of your audio source is distorted and whether the volume control is tuned to the suitable level. ~ Check if the batteries in the headphones have insufficient power. Replace fresh ones if necessary. ~ Check if the distance between the headphones and transmitter are within the effective range. (The effective range of the device is approx. 50M in open area.) Place the headphones closer to the transmitter. (2) No Sound from the headphones: ~ Make sure that your audio equipment, the transmitter and headphones are properly connected, powered and switched ON. ~ Check if the batteries are inserted properly into the battery compartment. ~ Check if the transmitter is powered on with the AC/DC adaptor: the Power LED Indicator (11) will keep Green showing the transmitter is powered (only when there is audio signal from the audio source). ~ Check if all the connection cords are properly connected. If you still have problem after checking the above points, please contact your customer service. Do not try to loosen the screws of the products to fix the problem. All the above are subject to our final change without further notice. Copyright by Atom Industrial Ltd.2009 0210ver2 0210ver2 SPECIFICATION Model AWD204 (900MHz) Description Radio Frequency (UHF) Wireless Headphones System (Power Auto Cut Off/ Phase Lock Loop/ ALC function/ Muting function/ Rechargeable function/ 3 Channel/ Color LED Indicator) Transmitter No. of Channels Carrier Frequency Channel 1: 91 .400MHz Effective Range 80 meters Power Supply AC/DC Adaptor Headphones Frequency Responses 20 - 20,000 Hz Signal to Noise Ratio 50dB Distortion <1% Channel Separation 30dB Power Supply 2 x 1.2V AAA size rechargeable batteries OR 2 x 1.5V AAA size normal batteries (Optional) System Included: 1 x Transmitter 1 x Headphones 1 x AC/DC 12V 200mAadaptor for transmitter 1 x 3.5mm Stereo Audio Cord (1.5m) (built in) 1 x Rechargeable Cord (built in) 2 x AAA NiMH550 mAH rechargeable battery Responsible party: Audiovox Accessories Corporation 111 Congressional Blvd., Suite 350 Carmel, IM46032 0210ver2 Channel 2: 913.000MHz Channel 3: 913.600MHz 0210ver2
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 9 Producer : GPL Ghostscript 8.15 Create Date : 2009:11:26 16:11:19 Modify Date : 2009:11:26 16:11:19 Title : Microsoft Word - 900MHz headphone IM- lab version.doc Creator : PScript5.dll Version 5.2.2 Author : UserEXIF Metadata provided by EXIF.tools