Atoms Labs AWS33R 7 inch LCD Monitor for HD System User Manual JSW QSG HDNVR 7R V1 2

Atoms Labs LLC 7 inch LCD Monitor for HD System JSW QSG HDNVR 7R V1 2

Contents

Users Manual

QUICK START GUIDEPRODUCT OVERVIEWINSTALLING YOUR DEVICESA. Setting up your monitor1. Insert the memory card and/or connect HDD device to USB port.2. Twist on the antenna to the LEFT side of the console.3. Connect the Ethernet cable from the BACK of the console to your router.4. Connect the 12V power adaptor and power on the system.5. Twist on the stand to the back of the console.Antenna Power BottonInternetRouterMobile DeviceConnect system directly after the router. Do not connect system to router through a hub or switcher.Enable DHCP and UPnP on your router. TCP port #6000 and #80 should be opened.Reset Botton USB PortMemory Card SlotPower JackNote: Before using the memory card/ HDD for recording video, you MUST format the memory card/ HDD on the console.KIT CONTENT*Camera / Receiver Antenna *Camera Stand*Digital Wireless Outdoor IR CameraEthernet Cablex 1Screw Pack (For Camera ) Camera / Receiver AdaptorCamera power adapter-5V/1.5A x 1HDNVR power adapter-12V/2ADigital Wireless Receiver Consolex 1 Note: Keep distance between device minimum 1 meter.MonitorRouter1 M+ 1 M+1 M+1 M+1 M+*Quantity varied subject to congurationThumb ScrewB. Installing your camera1. Secure the camera stand to a stable surface, celling or wall mount using three pcs screws.2. Loosen the thumb screw of the camera stand and secure the camera body to the bracket. 3. Screw the antenna into rear of the camera.4. Connect the supplied power adaptor to the camera and the power source. The RED LED will light up which indicate the camera is ready for setup. (1) (2) (3)7’ LCD Monitor for HD SystemAWS33R
SYSTEM OPERATIONQuick Select MenuDisplay/Undisplay MenuEnter Main MenuQUAD Display SelectSmart-QUAD Display SelectSingle Channel Record/Stop Single Channel RecordAll Channel Record/StopAll Channel RecordVolume Control Mute/Vol1Vol2/Vol3Main MenuMain Menu Camera SetupLive View with Quad DisplayLive View with Dynamic DisplayTap again to returnTurn CH2 oTap to turn on /o the camera Turn CH2/CH3 oTap one channel Live-view full screenTap again to returnTap one channel Show it at left side Live-view full screenSETUP THE HDNVR1. Tap to extend quick select menu.2. Tap to enter main menu. Pair the camera to HDNVRIf you have additional cameras disconnected with HDNVR , follow steps below to pair:1. Tap the camera setup icon to access the camera pairing screen.2. Select the Camera channel (Camera 1/2/3/4).3. Tap the "Camera Pairing" icon.4. Within 35 seconds, press and hold the pairing button on the back of the camera for 5 seconds. The Green Link LED will light up which indicate the camera is paired successfully.Tap one quadrant to choose the current channel, and a red check will display. HDNVR will display audio from the current selected channel.1.Camera Setup: Pair camera, and video quality.2.Recorder Setup: Setup recording settings such as date, recorder type, and motion area.3.Event list: Event video playback.4.System Setup: Setup system time, powersaving mode, and restore default system settings.5.Storage Setup: Management storage.1. Connect the device to your router, and make sure DHCP and UPnP service are enabled on your router setting.2. Power up and turn on HDNVR. In the Live View mode, wait until logo turns or . This means system is now ready for internet connection. The process takes around 30 seconds.3. Download the "WDVR Cam" app and run the app on a phone or tablet.Andrio For iOS For Android
APP INTRODUCTION4. Add New Device Andriod: Tap the "NEW" icon to add new device. iOS: Tap the "+" icno to add new device.5. Tap the “scan QR code” located on the rear of the device. Also you can enter the ID manually.6. Enter the default password "123456". Give your remote access a name and tap "save" to exit.7. Change the default password: For privacy matter, follow the steps below to change the security code on both device and app.Note: If you have not installed the app to scan the QR code, we suggest to download and install the app “Barcode Scanner ” .a. Device: 1. In the main menu section, tap storage setup 2. Tap network setting 3. Click DHCP then changes the password 4. Tap “OK” once you’re nished password modication b. WDVR CAM APPFor Andriod1. Go to the device list2. Press and hold the device name, the menu will appear on the panel. Then tap “modify”.3. Tap “update” once you’re nished password modication xxxxxxxxxxxxxxxxxxxxxxx123Main Menu Camera Setup1233-14Note: HDNVR allows max 3 remote viewers to access the system at a time. The 4th connection will be rejected.When a local user is operating setup menu. The remote user will be temporarily rejected to access HDNVR until the local user leaves the setup menu.HDNVR requires 1.5Mbps connection bandwidth per connection to receive best viewing quality/streaming. It is suggested to set camera resolution and quality to "Low" in order to receive streaming remote view if the bandwidth is below 1.5Mbps.8. Tap the device from the list, then tap "play" to connect. It will take a few seconds to access the remote video, depending on the network environment.For iOS1. Tap the ”+” icon to enter device list 2. Tap [Edit] button 3. Change default password123Add new deviceAdd new device/Device ListRemote SettingPush NoticationPlaybackSnapshotRecord ON/OFFDevice List Live ViewConnect/Disconnect DeviceAndriod iOS* Tap to connect HDNVR, then tap the “more” icon that setting menu will show up.
Products with CE Marking comply with EMC Directive (2014/30/EU); Low Voltage Directive (2014/35/EU); RED (2014/53/EU); ROHS Directive (2011/65/EU) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms:EMC: EN 301 489LVD: EN 60950Radio: EN 300 328If the camera system no longer functions or can no longer be repaired, it must be disposed of according to the valid statutory regulations. Disposal of spent batteries/accumulators:You are required by law (Battery Ordinance) to return all spent batteries and accumulators. Disposing of spent batteries/accumulators with common household waste is prohibited! Batteries/accumulators that contain hazardous substances are marked with the symbols on the side. These symbols indicate that it is prohibited to dispose of these batteries/accumulators in the household waste. The abbreviations for the respective heavy metals are: Cd=cadmium, Hg=mercury, Pb=lead. You can return spent batteries and accumulators that can no longer be charged to the designated collection points in your community, outlets or wherever batteries or accumulators are sold. Following these instructions will allow you to fulll the legal requirements and contribute to the protection of our environment!Push Noticationa. Enable/disable the push notication:For Andriod1. Go to more section to tap Push Notication. 2. Click/unclick to enable/disable the push notication.3. Enter user name.4. Tap ”OK” when you done.For iOS1. Tap icon.2. Enable/disable the push notication.3. Enter user name.4. Tap ”Save” when you done.12341234For Andriod1. Tap push notication setting2. Setup interval time of the pushFor iOS1. Tap push setting2. Setup interval time of the pushc. Time period:This function allows you to setup "Do Not Disturb" time. You can setup when Push is to start and end. Only during the time, you will receive the push.d. List:From list section, you can see which smart devices currently receive push from the system. WDVR app allows max 8 devices to receive the push. You may remove all devices from the push list by resetting the language. FACTORY DEFAULT SETTING1. Go to the system setting.2. Reset the language. 3. The system will restore to factory default. Note: Please change default security code and apply push service from smart devices after you reset the language and system parameter to default.b. interval Go to the push notication setting to setup interval time of the push. There are four options you can select how long you’ll receive the push. Note: Your smart phone will receive the push immediately after rst triggered. After that the camera will send the push according to interval time you setup. This function allows you to receive less push of one serial event happened continuously in time.Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority tooperate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCCRules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is no guarantee that interference willnot occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one ormore of the following measures:-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-- Consult the dealer or an experienced radio/TV technician for helpThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may notcause harmful interference, and (2) this device must accept any interference received, including interference that may causeundesired operationThis product is used and operated with a minimum distance of 20cm between the radiator and user body.

Navigation menu