Attenti US WMTD3318 ANKLE WORN GPS TRACKING DEVICE User Manual WMTD Users Manual
3M Electronic Monitoring ANKLE WORN GPS TRACKING DEVICE WMTD Users Manual
Users Manual
1
SMART® ACTIVE TRACKING
System Overview
Pro Tech’s Wearable Miniature Tracking Device (WMTD) utilizes GPS satellites to establish an
offender’s location by utilizing the cellular network to transmit the data.
Alert Button
Bracket
Serial Number
Charging Port
WMTD Communication and GPS Point Storage
• The standard WMTD call-in interval is once every hour while in compliance
• The WMTD will call Pro Tech as soon as a violation occurs, if a Contact is selected
• If the WMTD is not able to make a call because of poor cellular coverage, it will
continue trying to call in until it is successful
• The WMTD collects a GPS point every minute. If a Geographic Rule is in violation,
the WMTD will collect a GPS point every 15 seconds.
2
WMTD Indicator LEDs
There are three LEDs on the top of the WMTD, identified as Power, GPS, and Zone. The three
LEDs work separately and provide the offender with information. It is possible for any LED to
be flashing Green or Red and it is acceptable for the LEDs to be off. The WMTD will vibrate to
provide an indication that the offender must look at the LEDs. The LEDs function as follows:
PWR Zone
GPS
PWR LED
• This LED indicates the condition of the WMTD battery.
o LED off and WMTD deactivated: Acts as a battery indicator during the activation
process when the Alert Button is pressed
o LED off and WMTD activated: The WMTD is in power save mode
o LED blinking Green: The WMTD is either activated or in the process of being
activated. The battery does not need to be charged
o LED blinking Red: The WMTD is activated and the battery requires charging
• When the WMTD is connected to the charger, this LED will be solid (not flashing) Green
or Red.
o LED Red: The WMTD is not fully charged and should not be disconnected from
the charger
o LED Green: The WMTD battery has been completely charged and the charger
may be disconnected
GPS LED
• LED off: In normal condition
• LED flashing Green: It will flash in unison with the flashing “ZONE” LED during
activation
• LED flashing Red: Indicates a Motion No GPS warning or violation
ZONE LED
• LED off: In normal conditions
• LED flashing Green: It will flash in unison with the flashing“GPS” LED during
activation
• LED flashing Red: Indicates an Inclusion or an Exclusion Zone warning or violation
3
Rule Definitions
Hardware Rules
WMTD Battery
• The battery is getting low and the device needs to be charged. The device must be
charged for a minimum of two hours daily (the hours do not have to be consecutive).
When the battery needs to be charged, the device will vibrate three times
consecutively and then once every ten minutes until connected to the charger. During
this time, the Power LED will blink Red.
Motion No GPS
• Occurs when the WMTD has accumulated 10 minutes of motion in a 60 minute
period without receiving a signal from the GPS satellites. The device will vibrate
three times consecutively and once every ten minutes until the violation has cleared
by acquiring GPS. During this time, the GPS LED will blink Red.
WMTD Strap
• The strap has been compromised or removed from the WMTD. There will not be any
notifications to the offender that this has occurred, unless the officer selects the
Notify Offender with Vibrate option on this rule.
WMTD Alert Button Pressed
• When pressed, this button sends an alert to the contact. If the offender presses and
holds the button for one second, a single vibration will occur. This will also send out
a notification to the contact(s) specified on the rule.
WMTD Unable to Connect
• It has been over 2 ½ hours since the WMTD has contacted Pro Tech. This is normally
due to poor cellular coverage in the area. The offender is not notified of the Unable to
Connect. Once the WMTD is able to use the cellular network to call in, it will report
the violation and download all tracking data.
WMTD Tamper
• The WMTD has been compromised in some form. There will not be any notification
to the offender that this has occurred, unless the officer selects the Notify Offender
with Vibrate option on this rule.
4
Rule Definitions Cont.
Geographic Rules
Zone Rules- The offender has violated a Zone set up by the user. The device will vibrate
three times consecutively and once every ten minutes while still in violation, if the Notify
With Vibrate feature is checked. The Zone LED will blink in Red.
• Inclusion Zone
o Geographic areas like home, work, or school where the offender is confined
during an officer defined schedule
• Exclusion Zone
o Geographic areas used to define off-limits areas to the offender
5
Activating the WMTD Equipment
1. Press and hold the Alert Button on the front of the WMTD
for 3 seconds. If the “PWR” LED is Green then proceed
with activation. If the “PWR” LED is Red or does not light
up at all, then the WMTD will need to be charged prior to
activating.
2. Push tamper plugs into the back of the brackets of the
WMTD. Be sure to insert the left side first.
3. Place the pin tray on a flat surface, such as a desk, and push
one end of the strap into the pin tray until it is level with the
“lip” of the pin tray. Make sure that there is no gap
between the end of the strap and the edge of the pin
tray.
4. Insert strap with attached pin tray into one side of the
WMTD until it snaps in place.
5. Place the WMTD on the offender’s leg, just below the ankle
bone.
6. Wrap the strap around the offender’s leg and measure to the
line shown at right so that it allows approximately ¼ inch of
space between the offender’s leg and the strap to ensure
comfort.
6
Activating the WMTD Equipment Cont.
7. Using the strap cutters, cut the strap according to the
measurement taken in step six. Wipe off any fiber optic
cable residue left on the strap after cutting has been
completed.
8. Place remaining pin tray on a flat surface and insert
measured end of the underneath side (the bottom) of the
strap into the pin tray.
9. Place the WMTD on the offender’s leg just below the
ankle bone and insert the strap with attached pin tray into
the bracket until it snaps in place.
10. Press and hold the Alert Button on the front of the WMTD for 3 seconds.
a. The WMTD will vibrate once and the “PWR” LED will begin to blink Green,
indicating the WMTD is powered on.
b. The “GPS” and “ZONE” LED’s will blink Green once every second. This
indicates that the WMTD is attempting to make a wireless call.
c. The “GPS” and “ZONE” LED’s will blink Green twice every second. This
indicates that the WMTD is attempting to acquire GPS. The WMTD will need to
be taken outside to acquire GPS.
d. Once GPS has been acquired, the WMTD will vibrate once. The “PWR” LED
will continue to blink Green and the “GPS” and “ZONE” LED’s will stop
blinking. This indicates that activation has been successfully completed.
7
DEACTIVATING SYSTEM HARDWARE
• In PCE, go to the Hardware
Tab and click the Deactivate
Hardware button. The
following screen will appear.
Check the items that you wish
to deactivate and the reason
for the deactivation. Click the
Commit button at the bottom
of the screen.
• The WMTD needs to call in to
download any stored
information and receive the
Deactivation Command
8
Removing the WMTD Equipment
1. Cut the strap by using the strap cutters and remove the WMTD
from the offender’s leg.
2. Using a Pro Tech flathead screwdriver, push on the tamper
plugs to break them.
3. Use the screwdriver to remove the tamper plugs from the
brackets.
4. Using the screwdriver, press down the latch attached to the pin
tray.
5. While keeping the latch depressed, pull the strap with the
attached pin trays out of each bracket .
6. Discard tamper plugs, pin trays and the straps.
Note: We recommend putting replacement tamper plugs into the brackets of the WMTD.
Note: Do NOT reuse the tamper plugs.
Note: Do NOT remove tamper plugs from the brackets of the WMTD unless there is a
strap with an attached pin tray inside the bracket.
9
Enrolling an Offender Quick Reference
Open PCE.
Enter Contact Information
Enter Demographic Information
Select Time Zone
Go to the Reports Tab
Select which DVSR(s) you wish to receive
SAVE
Select View and Refresh Contacts to Update the PCE server
NOTE: You only need to enter a contact one (1) time
Offender Information
Enter Demographic Information
Select Time Zone
Select Level of Supervision (Equipment)
Enter Personal information (optional)
Enter Employment information (optional)
Enter Educational information (optional)
Enter Sentencing information, enter Offense (optional)
Enter Photo (if desired)
Enter Rules
Highlight specific Rule
Do you want the offender to receive notice of the violation?
Set a Grace Period (if desired)
Enter Actions for Hardware Rules
Choose a Contact; Page, Fax, Email
Enter Inclusion Rules for specific offender
Choose a radius
Choose a Grace Period (if desired)
Choose In-Charger for Home Rule
Do you want the offender to receive notice of violation?
Map the Address (Survey Rule if necessary)
Choose a schedule
Choose a Contact; Page, Fax, Email
10
Enrolling an Offender Quick Reference Cont.
Enter Exclusion Rules for specific offender
Choose a radius
Choose a Grace Period (if desired)
Choose In-Charger for Home Rule
Do you want the offender to receive notice of violation?
Map the Address (Survey Rule if necessary)
Choose a schedule
Choose a Contact; Page, Fax, Email
SAVE
Hardware Installation, Assignment and Activation
Insert the tamper plugs into the brackets
Place strap into pin tray and insert into the bracket
Measure the strap, insert strap into pin tray and place on offender’s ankle
Assign WMTD to offender in PCE Hardware tab
SAVE
Follow Activation Procedure on page 5
Take unit outside to acquire GPS.
Allow the WMTD to call in and wait until all of the LED lights (except for power) have
stopped blinking
Display Last Position in PCE
The map and one GPS tracking point will appear.
Deactivation
Choose offender in PCE
Go to Hardware tab
Choose Deactivate Hardware and Commit
Select a reason for the deactivation of the WMTD
11
FCC Certification
The Wearable Miniature Tracking Device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1.) This device may not cause harmful interference and
2.) This device must accept any interference received, including interference that may cause
undesired operation.
FCC ID: NC3WMTD3418, NC3WMTD3318, NC3WMTD3433,
PRO TECH MONITORING IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE
USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
FCC Radio Frequency Exposure
This Ankle Worn radio device has been evaluated under FCC Bulletin OET 65C and found to be
compliant with the requirements as set forth in evaluating compliance with FCC Guidelines for
Human Exposure to Radio frequency Electromagnetic Fields. This device is to be used solely by
law enforcement agencies for tracking purposes and must be professionally installed. The
radiation output power of this Ankle Worn device falls below the FCC radio frequency exposure
limits. The User must be informed that this device emits RF Energy and has been tested in an
ankle worn configuration and found to comply with all health and welfare agencies. The
antenna(s) used for this transmitter must not be co- located or operating in conjunction with any
other antenna or transmitter. This device is approved with emissions having a source-based time-
averaging duty factor not exceeding 2.4%.
Hereby, Pro Tech Monitoring Inc., declares that this GPS based tracking device is in compliance
with the essential requirements and other relevant provisions of Directive 1999/5/EC.