Atwood Mobile Products Hydro Flame 8935 Users Manual
8935 to the manual 196ecb4c-2e81-4831-8a6c-0d29928acf7f
2015-02-06
: Atwood-Mobile-Products Atwood-Mobile-Products-Hydro-Flame-8935-Users-Manual-500528 atwood-mobile-products-hydro-flame-8935-users-manual-500528 atwood-mobile-products pdf
Open the PDF directly: View PDF .
Page Count: 7
1
THIS INSTRUCTION MANUAL IS FOR USE BY AN AUTHORIZED SERVICE
TECHNICIAN TO INSTALL AN ATWOOD - hydro flameTM FURNACE.
INSTALLER: LEAVE THIS MANUAL WITH APPLIANCE.
CONSUMER: RETAIN THESE MANUAL FOR FURTHER
REFERENCE.
This furnace design has been certified for installation in recre-
ation vehicles as a MSP Category III furnace. Follow this installa-
tion instruction to insure safe operation of the furnace. Failure to
install furnace according to this installation instruction nullifies
the furnace warranty.
SAFETY ALERT SYMBOLS
Safety Symbols alerting you to potential personal safety hazards.
Obey all safety messages following these symbols.
WARNING CAUTION
avoid possible avoid possible
injury or death injury and/or property damage
INDEX
FURNACE SPECIFICATIONS ..............................................................1
DIMENSIONS ..................................................................1
WEIGHT ........................................................................1
MINIMUM CLEARANCE TO FLOORBOARDS, WALLS,
&SIMILAR COMBUSTIBLE BUILDING MATERIALS..................................2
SAFETY INFORMATION..................................................................1-2
FURNACE INSTALLATION ..................................................................2
VENT INSTALLATION - HORIZONTAL & VERTICAL ......................................2
WALL CUTOUT HORIZONTAL & VERTICAL ..............................................2-3
DUCTING HORIZONTAL & VERTICAL ......................................................3
Flexible Ducting......................................................................3
Hard Ducting ........................................................................3
OPTIONAL INSTALLATION - BOTTOM DISCHARGE KIT..................................3
GAS CONNECTION ........................................................................3
ELECTRICAL CONNECTIONS ..........................................................3-4
Conductor Sizing Table ............................................................3
12 volt DC Models ..................................................................3
120 volt AC Models ..............................................................3-4
Thermostat ..........................................................................4
CONVERTIBLE GAS CONTROL............................................................4
Valve Conversion ....................................................................4
Orifice Replacement ................................................................4
SYSTEM CHECK TESTS ....................................................................4
PROPANE GAS PRESSURE ..............................................................4
STATIC PRESSURE ........................................................................5
AC &DC WIRING DIAGRAMS ............................................................5
ILLUSTRATIONS ............................................................................6
REPLACEMENT PARTS LIST &DRAWING ..............................................7
SPECIFICATIONS *(W.C. = Water Column)
MODEL # 8935 8940 8935 8940
DCLP-III DCLP-III ACLC-III ACLC-III
BTU Input 35,000 40,000 35,000 40,000
Output BTU/HR 27,300 31,200 27,300 31,200
Type Gas LP LP LP/NAT LP/NAT
Duct Static Pressure - .10˝ W.C.* .10˝ W.C.* .10˝ W.C.* .10˝ W.C.*
Power Supply (VOLTS) 12-DC 12-DC 120-AC 120-AC
Watts - WITH OUT DOOR 151 151 360 360
Amperage 12.6 12.6 3 3
MINIMUM RETURN AIR 80 in280 in280 in280 in2
DIMENSIONS
WEIGHT
ALL MODELS WITH DOOR WIDTH HEIGHT DEPTH
Casing 16-1/2˝ 9-1/8˝ 23-1/2˝ - 26˝ FURNACE 38 lbs.
Vent 5˝ 5-3/8˝ SHIPPING 45 lbs.
ENGLISH, FRANCAIS (et Canada) •Installation
Effective 3/08
LITERATURE NUMBER MPD 31232
hydro flame
TM
8900-III-LD Series Furnace
MODELS 8935, 8940
Technical Installation Manual
WARNING: If the information in this manual is
not followed exactly, a fire or explosion may result
causing property damage, personal injury or loss of
life.
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Evacuate all persons from vehicle.
• Shut off gas supply at gas container or source.
• Do not touch any electrical switch, or use any
phone or radio in vehicle.
• Do not start vehicle’s engine or electric generator.
• Contact nearest gas supplier or qualified Service
Technician for repairs.
• If you cannot reach a gas supplier or qualified
Service Technician, contact the nearest fire
department.
• Do not turn on gas supply until gas leak(s) has
been repaired.
— Installation and service must be performed by a
qualified Service Technician, Service Center or
gas supplier.
2
MINIMUM CLEARANCE TO
FLOORBOARDS, WALLS & SIMILAR COMBUSTIBLE BUILDING MATERIALS*
MUST BE PROVIDED THE FULL LENGTH AND WIDTH OF UNIT
HORIZONTAL TOP ----1/2˝ BOTTOM 3/16˝ SIDES ----1˝ REAR --1/2˝
VERTICAL TOP ----1/2˝ BOTTOM ----0˝ SIDES ----1˝ REAR --1/2˝
Spacing of 1/4˝ to ducting within 3 feet of furnace must be provided
unless UL listed wire bound vinyl ducts are used. All ducting material
should be rated for continuous use at 200˚F.
NOTE: Clearances are specifically for plywood or similar building materi-
als surrounding furnace (i.e. furnace should NOT be located under
furniture or in a closet space where clothing or other material
could be located.)
NOTE: Efficiency rating is a thermal rating determined under continuous
operating conditions, independent of any installation. Efficiency
rate is given at 77% minimum, actual efficiency rating may be
higher.
WARNING
CARBON MONOXIDE POISONING
•Furnace must be installed and vented to these instructions.
•Improper installation, adjustment, alteration, service or mainte-
nance can cause injury or property damage.
•Improper installation location may cause furnace to produce neg-
ative pressure, affecting combustion air or venting of other appli-
ances.
CRITICAL INSTALLATION WARNINGS
• DO NOT install furnace on material that restricts return air, like carpet
or any soft material such as vinyl.
• DO NOT install furnace where clearance to combustibles cannot be
maintained.
• DO NOT modify furnace in any way.
• DO NOT alter furnace for a positive grounding system.
• DO NOT HI-POT furnace unless electronic ignition system (circuit
board) has been disconnected.
• DO NOT use battery charger to supply power to DC model furnace
even when testing.
• DO NOT use 120 volt AC current with DC models.
• DO NOT use furnace cabinet area as a storage compartment.
• DO NOT vent furnace with venting system serving another appliance.
• DO NOT vent furnace to an outside enclosed porch area.
• DO NOT use for temporary heating of buildings or structures under
construction.
• Protect building materials from degrading from flue gas exhaust.
• Protect furnace electrical components from water.USA AND CANADA -
FOLLOW ALL APPLICABLE STATE AND LOCAL CODES -
IN THE ABSENCE OF LOCAL CODES OR REGULATIONS, REFER TO CURRENT STANDARDS OF:
•Recreation Vehicles ANSI A119.2/NFPA 501C.
•National Fuel Gas Code ANSI Z223.1 and/or CAN/CGA B149
Installation Codes
•Federal Mobile Home Construction & Safety Standard, Title 24 CFR,
part 3280, or when this Standard is not applicable, the Standard for
Manufactured Home Installations (Manufactured Home Sites,
Communities and Set-Ups), ANSI A255.1 and/or CAN/CSA-Z240 MH
Series, Mobile Homes.
•Ground - National Electrical Code ANSI/NFPA No. 70 and/or CSA C22.1
•Park Trailers ANSI 119.5
NOTE: The direct high voltage spark ignition generates a radio frequency
that could cause interference with other microprocessor based
equipment. Locate equipment at least five feet (5’) from furnace
location. If this distance cannot be maintained, purchase MPD
37773 (a shielded high voltage lead).
WARNING
CARBON MONOXIDE POISONING
•Properly seal vent assembly to prevent carbon monoxide from
entering coach.
•DO NOT draw combustion air from living area. DO NOT vent exhaust
air into the living area or an enclosed porch.
Return air is supplied through openings in furnace casing. All return air
passages must be kept clear for furnace to function properly. Refer to
MINIMUM CLEARANCE TO FLOORBOARDS, WALLS &SIMILAR COMBUSTIBLE BUILDING
MATERIAL. The total unobstructed return air opening size(s) must NOT BE
LESS than specified in SPECIFICATIONS-MINIMUM RETURN AIR. Failure to meet
minimum return air requirements nullifies furnace warranty.
STANDARD FURNACE INSTALLATION
General Installation - LOCATION
• Install furnace through an exterior wall.
• DO NOT install furnace near tilt-out rooms, slide-outs, doors or
other projections that could obstruct furnace exhaust.
• Locate furnace near midpoint of coach for single furnace applica-
tions.
• Installation must provide accessibility if any repairs are necessary to
the furnace. Failure to meet this requirement will create additional
labor costs that will be the responsibility of the installer.
• DO NOT install vent in areas where projections or door openings
come within 6˝ of vent tube opening.
• DO NOT install furnace in an area where wires, pipes, or other
objects will interfere with the installation or operation of furnace.
• DO NOT directly install furnace on material that restricts return air,
such as directly on carpet, or soft material (like vinyl).
• If you must install furnace on carpet or soft material, install fur-
nace on cleats, or on a wood or metal panel extending the full
width and depth of furnace plus minimum clearances to com-
bustibles.
• DO NOT use petroleum or citrus type cleaners on plastic parts, as
damage may occur.
• The furnace must always be installed level (front to back, side to
side) to prevent water intrusion into the interior.
WALL CUTOUT OPTIONS
RECOMMENDED WALL THICKNESS 0˝ to 2-1/2˝
Do not oversize hole - oversizing can result in water leakage.
EXTERIOR WALL CUTOUT (FIG 1)A B C
HORIZONTAL &VERTICAL 3-1/8˝ 2-3/8˝ 3-1/2˝ DIA HOLE
VENT INSTALLATION (FIG 1)
HORIZONTAL &VERTICAL INSTALLATION
1. Locate vent hole cutout as called out in (FIG 1).
2. Drill 3-1/2˝ diameter hole through side wall of coach.
3. Remove vent and vent ring from furnace.
3
4. Insert furnace from backside of wall. Line up hole in wall and furnace.
5. Apply sealant to back of vent ring and vent cap base.
6. Install vent assembly with HOT at top for horizontal and on right
side for vertical installation (FIG 1-1A). Slip vent into combustion air
intake tube. Secure to wall with four (4) screws.
7. Vent must have a minimum 1-1/4” over lap on exhaust tube and a
minimum 1/2˝ overlap on combustion airtube.
8. Horizontal units - secure to floor with two (2) screws through legs
on back of casing. Vertical units use vertical mounting brackets and
self-tapping screws to hold furnace to floor (tabs on control box can
be used also to secure furnace).
DUCTING - HORIZONTAL &VERTICAL (FIG 3-4A)
HORIZONTAL
PROPER DUCT INSTALLATION IS CRITICAL TO THE OPERATION OF THIS FURNACE
CONTINUOUS USE MATERIALS RATING
DUCTS 9˝ IN LENGTH OR MORE 200˚F.
4˝ DUCTS LESS THAN 9˝IN LENGTH 250˚F.
METAL BOOTS LESS THAN 9˝ IN LENGTH 250˚F.
Ducting systems can include any combination of discharge openings, as
long as static pressure and minimum discharge area requirements are met.
ALL MODELS - (also see STATIC PRESSURE TEST)
REQUIRED MINIMUM DISCHARGE 48 IN2
REQUIRED MINIMUM RETURN AIR 80 IN2
• See MINIMUM CLEARANCE TO FLOORBOARDS, WALLS &SIMILAR COMBUSTIBLE
BUILDING MATERIALS.
• Each 4-inch duct opening provides 12 in2of discharge area. Provide
an extra 12 in2of non closeable duct discharge area for each
closeable register used.
• Use of 2˝ ducts does not count toward achieving min. discharge req.
Ducting in dead air space with no return air, such as holding tank
areas, does not count toward achieving min. discharge requirements.
• Adjust ducting installation to obtain air rise of 100˚F - 130˚F.
Flexible Ducting System
When designing Flexible Duct Systems:
• avoid sharp bends or crushed ducts
• stretch all ducts and run them directly to outlets, keeping quanti-
ty and angles of bends to a minimum
1. Remove knockout plates from desired outlets.
2. Attach duct adapter to each opening, by inserting flange over casing,
locking tab into casing slot and turning adapter 90˚.
3. Attach and secure FOUR-INCH flexible ducts to adapters.
4. Run ducts to desired location within RV, secure to registers.
5. Additional ducting may be needed to maintain static pressure.
Hard Ducting Floor System
When designing Hard Duct Systems:
• undersize ducting will cause high temperature limiting
• oversize ducting will cause inadequate air flow from registers
• when hard ducting is 1-1/2˝ in depth, an additional flex duct may
be needed to maintain installation static requirements
• DO NOT install floor registers within 2 feet of return air openings.
OPTIONAL INSTALLATION - BOTTOM DISCHARGE (FIG 4-4)
1. Remove bottom discharge cover plate. This ducting option must
be connected to a ducting system. FIG 3 (parts breakdown) #40 -
GASKET AND PLENUM PLATE KIT is available when attaching furnace.
2. If cutout is required: FLOOR CUTOUT
BOTTOM DISCHARGE ABCD
HORIZONTAL-WITHOUT DOOR (FIG 4) 18-20 1/2˝ 5-1/2˝ 10-1/2˝ 3/4˝
3. Fasten plenum plate (4-E) over floor cutout. If a gasket and
plenum plate are not used, seal furnace to hard duct system mak-
ing sure seal is air-tight, continue with STEP 5.
4. Position gasket (4-F) on plenum plate.
5. Set furnace on gasket, gasket must remains in position.
Use additional ducting to maintain correct static pressure.
VERTICAL
The only ducting option, when using vertical installation, are the top
two ducts and tw ducts off the back of the casing. This is the only
configuration allowed with vertical installation (FIG 3A).
GAS CONNECTION
1. Connect gas line to fitting on top rear of furnace. Be sure all male
pipe threads, other than flare fittings, are treated with a sealing com-
pound resistant to the action of propane (LP) gas. DO NOT put sealing
compound on flare fittings.
2. A 3/8˝ flared fitting connection is provided for supply connection to
furnace. The gas supply line of the furnace must be of adequate size
to provide 11˝ W.C. gas pressure. This pressure must be maintained
under maximum flow conditions with all gas appliances in operation.
3. Use two wrenches to hold fitting and flare nut when tightening gas
line to fitting. (FIG. 2)
ELECTRICAL CONNECTION (FIG 5)
WARNING
INJURY OR PROPERTY DAMAGE
• Label all wires before disconnecting for service. Wiring errors can
cause improper and dangerous operation.
Verify proper operation after servicing.
• Disconnect electrical power before servicing.
Conductor Sizing Table - MAX. 10% VOLTAGE DROP - (12 VDC)
CURRENT DRAW (AMPS)
8 9 10 15 20
GAGE MAX. LENGTH OF SAE CONDUCTOR (IN FEET) FROM SOURCE TO DEVICE
18 21 19 17 11 9
16 33 29 26 17 13
14 52 46 41 28 21
CAUTION
PROPERTY DAMAGE
•This connection is for low-voltage battery or direct current only. Do
not connect to 120- or 240- volts AC.
This unit is designed for negative ground 12 volt DC ONLY. Polarity
must be observed so furnace motor will run in proper rotation. DO NOT
attempt to alter to a positive ground system.
12 VOLT DC MODELS
Route 12 volt DC and thermostat leads to left side of control box. Use
a minimum of 18 GA wire to minimize voltage drop. The furnace must
be installed so electrical components are protected from water. To
make electrical connections: see WIRING DIAGRAM FIG 5
1. Route wiring to left side of furnace.
2. Connect red wire to positive side of power supply.
3. Connect yellow wire to grounded side of power supply.
4. Connect blue wire marked positive thermostat to + side wire of
thermostat using 22-18 GA stranded wire.
5. Connect the other blue wire to the other thermostat lead using
minimum 22-18 GA stranded wire.
See instruction with thermostat for complete wiring directions.
For best furnace performance when power supply is from a converter
equipped with a charging port, wire the converter to furnace parallel
with battery. This provides consistent voltage to furnace, increasing
component life, filtering power surges and AC spikes
120 VOLT AC MODELS
Route 120 volt AC and thermostat leads to wires located on the left
side of control box using a minimum of 18 GA wire. The furnace must
be installed so electrical components are protected from water. To
make electrical connections see WIRING DIAGRAM FIG 5.
4
1. Route wiring to left side of furnace.
2. Remove junction box cover.
3. Connect 120 white wire to furnace 120 white wire.
4. Connect 120 black wire to furnace 120 black wire.
5. Connect ground wire to furnace green ground wire.
After field hookups have been made, put wire connections into
furnace junction box and replace cover.
6. Connect thermostat leads to the two blue furnace thermostat leads.
NOTE: Furnace is equipped with a 120 volt AC motor. All other
electrical component parts are supplied with power from a trans-
former inside the furnace at 24 volts AC.
NOTE: A 120 volt model can also be supplied with a 30 inch
power cord attached from the factory supplied with a molded plug
with ground pin.
NOTE: DC units are supplied with a power switch
which when turned OFF for servicing will remove power through the
furnace wiring. Switch must be in ON position for furnace to operate.
See FIG 3-G. AC units switch is in valve circuit only.
POWER SUPPLY
Atwood Mobile Products highly recommends the use of an electronic
(solid state) converter with clean, clear power output. This will assure
the life of the electronic controls and motor life could be extended as
much as 500% beyond typical linear converter applications.
THERMOSTAT INSTALLATION
The thermostat is very sensitive. HANDLE WITH CARE AT ALL TIMES.
Locate thermostat 48˝ to 54˝ above floor on an INTERIOR wall away from
areas of abnormal heat or cold. EXTERIOR wall location must have a 3/4˝
spacer between thermostat and exterior wall.
Follow manufacturer’s installation instructions provided with thermo-
stat. When a thermostat is not supplied use a thermostat rated for 12
VDC or 24 VAC minimum lamp.
CONVERTIBLE GAS CONTROL FIG 6
LC MODEL UNITS come equipped with a convertible gas control. Each
unit is supplied with two main burner orifices. One will be in place, the
other will be attached to blower housing cover. Each orifice will be
clearly marked with a drill size as shown below.
GAS TYPE BTU/HR LINE PRESSURE VALVE REGULATOR DRILL SIZE
PROPANE (LP) 40,000 11˝ W.C. 10.5˝ W.C. 49P
NATURAL (NAT) 40,000 7˝ W.C. 3.5˝ W.C. 30N
PROPANE (LP) 35,000 11˝ W.C. 10.5˝ W.C. 51P
NATURAL (NAT) 35,000 7˝ W.C. 3.5˝ W.C. 32N
The pressure settings of the convertible valve are set for natural gas
NAT 3.5˝ W.C. or LP 10.5˝ W.C. and are not adjustable. Use Loctite
#RC609 on orifice threads when installing a new orifice. 1/8˝ NPT plug
is provided upstream of gas connections for checking gas pressure.
VALVE CONVERSION (FIG.6)
1. Check exposed section on side of adjustment plug to determine
whether it is set for natural or propane. NAT is stamped on one end
and LP is stamped on the other end of plug. The types of gas in use
will be showing right side up.
2. Unscrew plug and remove from valve tower. DO NOT remove rod from
tower or make any adjustments.
3. A. When set for LP and NAT is required:
Rotate plug and replace into valve tower.
NAT SHOULD NOW BE VISABLE FIG 6
B. When set for NAT and LP is required:
Rotate plug and replace into valve tower.
LP SHOULD NOW BE VISABLE FIG 6
4. Check rod for proper positioning while tightening plug into tower.
The plug, which has been factory calibrated for this valve only,
should be reinstalled finger tight. DO NOT USE PLUG ON ANY OTHER VALVE.
INSTALL ONLY THE CORRECT MAIN BURNER ORIFICE FOR TYPE OF GAS BEING USED.
ORIFICE REPLACEMENT
1. Unit will need to be removed if installed, if not start with step #2.
2. Remove burner cover and extended manifold.
3. Remove burner assembly from control box.
4. Remove two screws holding burner head in place.
5. Use a 7/16˝ socket to remove orifice and replace correct orifice cor-
responding to type of gas required, which corresponds to regulator
plug setting FIG 6.
6. Replace burner head with two screws.
7. Reinstall burner assembly. Burner assembly must seal tight against
control box.
8. Install extended manifold and apply thread sealant to threads going
into gas valve.
9. After converting furnace, IN PLAIN SIGHT, put “CONVERTED” sticker (pro-
vided in your conversion packet) on rating label.
SYSTEM CHECKS
WARNING
FIRE OR EXPLOSION
• Never check for leaks with an open flame.
DIAGNOSTIC CHART
FAULT LED INDICATION
Internal Circuit Board Failure Steady on, no flashing
Limit switch/Airflow problems 1 flash with 3-second pause
Flame Sense Fault 2 flashes with 3-second pause
Ignition Lockout Fault 3 flashes with 3-second pause
PROPANE GAS PRESSURE TEST
The furnace and any individual shut-off valve must be disconnected
from gas supply piping system during any pressure testing of system
at test pressures of more than 1/2 PSI.
Before furnace is connected, piping systems must be tested to be leak
free. The test must maintain air pressure of at least 6˝ of mercury or 3
PSI for at least 10 minutes.
The entire piping system must be maintained within a range of 10-14˝
W.C. when all appliances are in operation. Test the gas connections for
leakage with a leak test solution.
STATIC PRESSURE TEST
CASING STATIC PRESSURE TABLE
If duct static pressure cannot be set, casing static pressure should not exceed
the values listed below when taken cold.
DUCTING SYSTEM OPERATING VOLTS FLEXIBLE HARD
DC MODELS 12 0.25˝ W.C. 0.35˝ W.C.
AC MODELS 120 0.25˝ W.C. 0.35˝ W.C.
NOTE: For maximum performance and reliability refer to Installation Addendum
for manufacturer’s recommendations and specifications.
Voltage greater than indicated will cause higher static readings.
Reducing the number of duct turns and stretching ducts will increase
air flow and reduce static pressure. Adding ducts or increasing dis-
charge system (hard ducting) will also reduce static pressure.
NOTE: Special tool required to take casing static pressure. Location for
Static Pressure Tap for casing is located on back of casing (top left
corner) FIG 3.
5
8900-III AC WIRING
5
BLACK
BLUE
RED
YELLOW
HIGH TENSION
+ 12V DC
NEG
RED
YELLOW
ELECTRODE
YELLOW
VALVE RED
+THERMO
MOTOR
CIRCUIT
BREAKER
IGNITION
BOARD
BLW PWR
SAIL
SWITCH
BLUE
BLUE
LIMIT
SWITCH
WHITE
BLUE
YELLOW
RED
GROUND
THERMOSTAT
ON
OFF
ON/OFF
SWITCH
THERMO
RED
IMPORTANT: If any original wire has to be replaced, it must
be replaced with type 105 C or its equivalent.
Terminal Block on 85 Models only.
CUSTOMER SUPPLIED WIRE
8900-III DC WIRING
5
12V DC
SUPPLY
PICTORIAL DIAGRAM SCHEMATIC DIAGRAM
Off
On
Valve
Electrode
Green
Sail
Switch
Green
Yellow
33
22
11
White
Black
Yellow
Black
Black
Yellow
Red
Blue
Blue
Limit Switch
Blue
Red
Green
Yellow
Transformer
Ignition Control
Black
Brown
Motor
120 VAC Green
120 VAC Black
120 VAC White
White
Thermo Blue
AC Capacitor Motor Run
+Thermo Blue
HIGH TENSION IMPORTANT If any original wire has to be replaced, it must bereplaced with the type 105 C or its equivilant.
t
t
White
Black 24 VAC
TF
CAP
MOT
3
2
3
SS LS IG
PS
TH
R
L1
IND
GND
HV
V1
P/S
GV
EL
DO NOT
GRIP
HERE
14
23
++
123 45 6
HV = High Voltage PS = IG Power Input
GND = Ground SS = Sail Switch
GV = Gas Valve TH = Thermostat
EL = Electrode LS = Limit Switch
IG = Egnition Control CAP = Capiacitor
MOT = Blower Motor P/S = Power Switch On/Off
IND = IG Blower Motor Output TF = Transformer
V1 = Valve Control
GND
Green
White
Black
120VAC
NOTE: DC Models only
ON/OFF Switch may be sep-
arate or combined in Circuit
Breaker.
A
Valve Assembly
(Vanne)
Valve Conversion
(Vanne de conversion)
6
E
F
A
B
C
D
3
2
4
G
OUTSIDE RV
(EXTERIEUR DU VEHICULE)
Gas Line
(Conduite de gaz)
1A
AVANT DU VEHICULE
B
A
1
C
3A
MUST USE
MUST USE
MUST USE
MUST USE
6
6
7
20
2
13
35
32
30
3
4
31
33
29
7
17
36 25
1
18
23
34
40
52
24
39
A
42
5
51
6
43
16
28
50
9
8
DRAWING #DESCRIPTION OF PARTS
2 Thermostat - specify color
3 Duct Cover Plate
4 Duct Adapter
5 Orifice — SPECIFY GAS & BTU
6 Combustion Wheel
7 Motor Gasket
8 Valve DC
9 Valve Repl Coil DC
13 Electronic Ignition Board DC Kit
16 Valve AC
17 Motor DC
18 Sail Switch
20 Circuit Breaker DC
23 Junction Box Asmbly AC
24 Motor Capacitor AC
25 Element Exhaust Wall Gasket
28 Valve Replacement Coil AC
29 Blower Wheel
30 Electrode
31 Limit Switch
32 Burner Assembly
33 Element Assembly
34 Electronic Ignition Board AC Kit
35 Transformer Assembly AC
36 Motor AC
37 High Voltage Wire
39 Vent Assembly (specify model) 35/40
40 Gasket & Plate Assembly
42 Combustion Cover
43 Extended Manifold (specify)
50 Motor Wall - Specify Model
51 Vent Ring
52 Gas Line Gasket
N˚ SUR LE SCHÉMA DESCRIPTION DES PIÈCES
2 Thermostat - spécifiez la couleur
3 Couvercle de l'ouverture de branchement du conduit
4 Adaptateur de conduit
5 Lumière — PRECISEZ LE CALIBRE
6 Ventilateur d'air de combustion
7 Joint d'étanchéité du moteur
8 Soupape CC
9 Bobine CC de rechange pour soupape
13 Module CC de plaquette d'allumage électronique
16 Soupape CA
17 Moteur CC
18 Interrupteur à abattant
20 Coupe-circuit CC
23 Boîte de dérivation CA
24 Condensateur de moteur CA
25 Joint d'étanchéité entre la paroi et le système d'é-
vacuation de l'élément de chauffage
28 Bobine CA de rechange pour soupape
29 Ventilateur
30 Électrode
31 Rupteur thermique
32 Brûleur
33 Elément
34 Module CA de plaquette d'allumage électronique
35 Transformateur CA
36 Moteur CA
37 Fil à haute tension
39 Ventilation (préciser le modèle) 35/40
40 Ensemble joint d'étanchéité et plaque
42 Panneau d'air de combustion & anneau de ventilation
43 Distributeur (préciser)
50 Mur du moteur – identifier le modèle
51 Anneau
52 Joint d’étanchéité du tuyau de gaz
hydro flameTM
8900-III-LD Series
Furnace Models 8935, 8940