Aube Technologies Ti072 Users Manual 400 072 000 C ENG
TI072 to the manual 25436852-1619-4244-b8e3-857b690f8102
2015-02-06
: Aube-Technologies Aube-Technologies-Ti072-Users-Manual-500563 aube-technologies-ti072-users-manual-500563 aube-technologies pdf
Open the PDF directly: View PDF .
Page Count: 4
Download | |
Open PDF In Browser | View PDF |
400-072-000-C ENG.fm Page 1 Thursday, May 8, 2008 2:45 PM NOTE: TI072 This switch cannot be used if there is no neutral wire (white wires joint together) inside the electrical box. User guide 7-day Solar Programmable Wall Switch n Applications 1. p Quick Start-up The TI072 programmable wall switch has been designed to control lights and motors: Load types Maximum load Lights and resistive loads (except tungsten) 1800 W (15 A @ 120 V) Tungsten lights 1440 W (12 A @ 120 V) Motors 1 hp o n o p q Examples fluorescent lights compact fluorescent lights (CFL) electronic ballasts sodium lamps block heaters incandescent lights halogen lights pool filter pumps fans • • • • • • • • • Installation 2. Set the time and date before using the timer for the first time. The TI072 will turn the lights on at sunset and turn them off at 11:00 pm by default. If these settings are appropriate for you, you only need to set the time and date (see shaded zone in the menu flowchart sheet). If the switch’s sunset time does not correspond to the actual sunset time, see sections 5.3.3 and 5.3.4. q Operation Indicates the mode of operation (see Section 5.1) The icon indicates the current program has been activated at sunset. Indicates the keypad is locked (see Section 6) The icon indicates the current program has been activated at sunrise. Indicates the load on/off state Cut power at the circuit breaker to avoid electric shock. Indicates the current program Remove the existing switch. (For a 3-way installation, identify and label the wire that is connected to the “common” screw.) Briefly press this button to turn the lights on or off. See “Temporary Override” in Section 5.1.4. Press for 3 seconds to enter the setup menus. Press this button to display today’s sunrise time. Press this button to display today’s sunset time. Install the new switch. Apply power at the circuit breaker. r black (3 sec.) blue (LOAD) white (NEUTRAL) white 120 VAC 5.1 You can use the Mode menu to select one of the three modes of operation (see sections 5.1.1 to 5.1.3). In Manual mode, the TI072 operates like a regular switch. To turn the lights on or off, briefly press the main button. The icon appears when the switch is in Manual mode. 120 VAC white blue (LOAD) black jumper white (NEUTRAL) 5.1.2 Automatic Mode black (LINE) In Automatic mode, the TI072 turns the lights on or off according to the set programs (see Section 5.4). The icon as well as the current program number are displayed. yellow (3 WAY) red black three-way switch white Connect the LOAD wire on the TI072 to the “common” wire, which you identified when removing the old switch. Connect the NEUTRAL wire to the neutral (white) wires. Connect the LINE and 3 WAY wires to the two remaining wires. At the other 3-way switch, connect the jumper wire between the “common” screw and the screw where the LINE wire of the TI072 is connected. NEW 3-WAY INSTALLATION black black (LINE) yellow (3 WAY) 5.1.3 Random Mode In Random mode, the TI072 has no specific times to turn the lights on or off. This mode is designed to give the impression the house is occupied during your absence. It is similar to the Automatic mode except there is no fixed program. The programs are automatically set to different times by the TI072 every day. The icon appears when the switch is in Random mode. The first “On” program occurs at sunset. Each “On” program lasts between 1 hour and 1 hour and 30 minutes; each “Off” program lasts between 15 and 30 minutes. The last “Off” program occurs between 10:30 pm and midnight. 5.1.4 Temporary Override When the TI072 is in Automatic or Random mode, you can press the main button at any time to override the default state for the current program. The light will turn off if they are on and vice versa. The icon (On or Off) of the new state flashes to indicate that the state is temporary. The new state is maintained until you press the main button again or till the next “On” or “Off” program. blue (LOAD) white (NEUTRAL) black Mode Menu 5.1.1 Manual Mode black white Press the main button for 3 seconds to enter the setup menus. Refer to the menu flowchart sheet on how to navigate the menus. black (LINE) black white 5. yellow (3 WAY) EXISTING 3-WAY INSTALLATION white The LED illuminates when the load state is on. Setup Menus white TI072 4. Indicates the time and day SINGLE-SWITCH INSTALLATION 120 VAC 3. 5.2 white black single-pole switch Time Menu The time display flashes on the screen when the time has not yet been set or after a 4-hour power outage. Use the Time menu to select the time format (12-hour or 24-hour) and to set the clock and date. NOTE: The date is used to determine the sunset and sunrise times. 400-072-000-C 2008-05-08 1/2 400-072-000-C ENG.fm Page 2 Thursday, May 8, 2008 2:45 PM 5.3 Configuration Menu (Conf) Use the Configuration menu to set the following parameters (see sections 5.3.1 to 5.3.4). minutes. If, later in the year, the sunset time is 4:01 pm, the program will start at 4:31 pm. NOTE: When you enter an offset, appears along with or when you display the sunset or sunrise time. To remove the offset, display the sunset or sunrise time and change the minutes until disappears. • 5.3.1 Backlight mode (SCRN) The screen is lit at high intensity for 8 seconds when you press any button. The rest of the time, depending on the backlight mode selected, the screen behaves as follows: Scrn Off: The screen is not lit. Scrn On HI: The screen is lit at high intensity. Scrn On LO: The screen is lit at low intensity (default mode). 5.3.2 Automatic Daylight Savings Time Changeover (DLS) When automatic daylight savings time changeover is on (DLS On), the TI072 changes to daylight savings time (summer time) at 2:00 am on the second Sunday of March and changes back to normal time (winter time) at 2:00 am on the first Sunday of November. This function is enabled (DLS On) by default. 5.3.3 Latitude and Longitude Coordinates (LAT and LONG) The coordinates are used to turn the lights on at sunset and off at sunrise. The latitude is set to +45 and longitude to -75 by default. These settings provide approximate sunset and sunrise times for most North American cities. To obtain your city’s coordinates (or those of a nearby city), see the coordinates table. You can also obtain this information at www.aubetech.com/timer or with a Global Positioning System (GPS) device. The accuracy of the sunset and sunrise times depends on the accuracy of the coordinates you enter for your city. NOTE: Enter a negative value for a south latitude or a west longitude. 5.3.4 Correction Factor (ADJ) If your city’s time zone is based on political or economic boundaries instead of its coordinates, your lights might switch on or off too early or too late with respect to sunrise and sunset. In this case, apply a correction factor (+1 or -1 hour; refer to addendum). Otherwise, leave it at 0 (default value). 5.4 Select a program number (see section 5.4.1) Set the day(s) of the program (see section 5.4.2) Program 5.4.1 Selecting a program number Time P01 On All 7 days sunset P02 On to P07 On None — Program Days Time P01 Off All 7 days 11:00 pm P02 Off to P07 Off None — Program Days Time P01 On All 7 days sunset P02 On to P07 On None — Program Days “P01 On” All 7 days sunrise P02 Off to P07 Off None — Example 3: The lights turn on at 8:00 pm every day and turn off at 10:00 pm every day except on Saturday night when they turn off at 1:00 am. Program P01 On P02 On P03 On P04 On P05 On P06 On P07 On Days All 7 days None None None None None None Time 8:00 pm — — — — — — Program P01 Off P02 Off P03 Off P04 Off P05 Off P06 Off P07 Off Days Sunday (Su) Monday (Mo) Tuesday (Tu) Wednesday (We) Thursday (Th) Friday (Fr) Sunday (Su) Time 10:00 pm 10:00 pm 10:00 pm 10:00 pm 10:00 pm 10:00 pm 1:00 am If you set “P01 Off” at 10:00 pm for all 7 days and set “P02 Off” to 11:00 pm for Saturday. On Saturday, the lights will turn off at 10:00 pm, not 11:00 pm since “P01 Off” is set to an earlier time than “P02 Off”. s Keypad Lock 6. “P01 Off” After selecting a program, set the day(s) of the program. You can select a specific day, all 7 days or “none”. Choose “none” for any unused program. 5.4.3 Setting the program start time After setting the day(s) of the program, set its start time. You can select either a specific time, the sunset time or the sunrise time: • To select a specific time: (1) Advance to the hour setting and select the hour. (2) Advance to the minutes setting and select the minutes. • To select sunset or sunrise time: (1) Advance to the hour setting and select the sunset time or sunrise time. (When you scroll, the sunset time and sunrise time appear between 11 pm and 12 am.) (2) To enter an offset (from -70 to +70 minutes in 10-minute increments) between the sunset or sunrise time and the program start time, advance to the minutes setting and change the minutes. • EXAMPLE: If the sunset time is 6:13 pm and you change the minutes to display 6:43 pm, you have entered a delay of 30 The ambient temperature is either below or above switch’s operating temperature. The display disappears when you toggle the other switch. Swap the LINE and 3-WAY wires. The sunset or sunrise time is inaccurate. • The date or time is wrong (see section 5.2). • The longitude or latitude is wrong (see section 5.3.3). • The correction factor is wrong (see section 5.3.4). • You have entered an offset (see section 5.4.3). v Time P01 Off 2 sec. NOTE: You must perform the whole procedure in an interval of 2 seconds. If the procedure was not properly performed, wait another 2 seconds before retrying. t Reset to default Settings To return the switch to its default settings, simultaneously press both main and left buttons and hold. The software version will appear for 5 seconds. RST will appear for the next 5 seconds. Release the buttons when all segments appear on the screen. The switch is now reset (see default settings in the menu flowchart). 7. 8. The display is faded or irregular. Example 2: The lights turn on at sunset and off at sunrise every day. 5.4.2 Setting the day(s) of the program TI072 Days When the keypad is locked, the icon appears on the screen and the only change permitted is the changing of the state. For example, if the lights are off, they will turn on when you press the main button. However, in Automatic mode, the default state for the current program will be overridden until the next program starts. If you press the main button again before the start of the next program, the lights return to their initial state. To lock or unlock the keypad, press the buttons in the following order: Set the program start time (see section 5.4.3) You can set up to 21 “On” programs (“P01 On” to “P21 On”) and 21 “Off” programs (“P01 Off” to “P21 Off”). For example, select an “On” program to set when to turn the lights on; select an “Off” program to set when to turn the lights off. Example 1: The lights turn on at sunset and off at 11:00 pm every day (default setting). Be careful about overlapping! Program Menu (Prog) Use the Program menu to set the programs; i.e. the times you want the lights to turn On or Off when the switch is in Automatic mode. To set a program, proceed as follows: n o p 5.4.4 Examples u Troubleshooting Specifications 9. Supply: 120 VAC, 60 Hz Maximum load: 1800 watts Operating temperature range: -15 °C to 50 °C (5 °F to 122 °F) Storage temperature range: -40 °C to 60 °C (-40 °F to 140 °F) Power outage: The screen is blank. Only the time must be set if the outage lasts more than 4 hours; all other settings and programs are permanently saved. Latitude range: from -65° to +65° Solar table precision: +/- 11 min. (within ±60° latitude) Certification: UL (c UL us) ; 10. Warranty AUBE warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of three (3) years from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, AUBE shall repair or replace it (at AUBE's option). If the product is defective, (i) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it, or (ii) contact AUBE. AUBE will make the determination whether the product should be returned, or whether a replacement product can be sent to you. This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by AUBE that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer. AUBE's sole responsibility shall be to repair or replace the product within the terms stated above. AUBE SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some provinces, states or regions do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS WARRANTY. Some provinces, states or regions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary according to the province, state or region. Technical Assistance 11. 705 Montrichard Avenue Saint-Jean-sur-Richelieu, Quebec J2X 5K8 Canada Tel.: (450) 358-4600 Toll-free: 1-800-831-AUBE Fax: (450) 358-4650 Email: aube.service@honeywell.com For more information on our products, go to www.aubetech.com 400-072-000-C 2008-05-08 2/2 400-070-003-C EFS.fm Page 1 Wednesday, April 9, 2008 8:56 AM TI070 / TI071 / TI072 Menu flowchart Organigramme des menus Organigrama de los menus Legend / Legende / Leyenda Flowchart shows default settings Le diagramme contient les réglages par défaut. El diagrama contiene los ajustes por defecto. Briefly press this button to go to preceding menu or setting. Appuyer brièvement sur ce bouton pour passer au menu ou réglage précédent. Presionar brevemente este botón para ir al menú o ajuste precedente. Briefly press this button to go to next menu or setting. Appuyer brievement sur ce bouton pour passer au menu ou réglage suivant. Presionar brevemente este botón para ir al menú o ajuste siguiente. (3 sec.) Briefly press this button to accept setting and display next parameter. Appuyer brievement sur ce bouton pour accepter le réglage et afficher le prochain paramètre. Presionar brevemente este botón para aceptar el ajuste y visualizar el parámetro siguiente. Mode menu Menu de mode Menú de modo Press this button for 3 seconds to enter or exit the setup menus. Appuyer sur ce bouton pendant 3 secondes pour entrer ou sortir des menus. (3 sec.) Presionar este botón durante 3 segundos para entrar o para salir los menús. Auto/Manual/Random Auto/Manuel/Aléatoire Auto/Manual/Aleatorio (sec. 5.1) Minimum settings for quick start-up Réglages minimaux pour démarrage rapide Ajustes mínimos para el encendido rápido Clock starts. L’horloge commence à compter. El reloj comienza a contar. Time menu Menu de l’heure Menú de la hora 24H / 12H Hour Heure Hora Year Année Año Minutes Minutes Minutos Month Mois Mes Day Jour Día Configuration menu Menu de configuration Menú de configuración Backlight Rétroéclairage Retroiluminación (sec. 5.3.1) Automatic Daylight Savings Time Passage automatique à l’heure avancée Cambio automático a la hora de verano (sec. 5.3.2) Longitude * Longitude Longitud (sec. 5.3.3) Correction factor Facteur de correction Factor de corrección (sec. 5.3.4) None selected Nul (None) sélectionné Ninguno (None) seleccionado Program menu Menu de programme Menú de programa Day(s) selected Jour(s) sélectionnés Días seleccionados Program number No. du programme Nº del programa (sec. 5.4.1) Program day(s) Jour(s) du programme Días del programa (sec. 5.4.2) * Enter a negative value for a south latitude or a west longitude. Inscrire une valeur négative pour une valeur de latitude sud ou une valeur de longitude ouest. Ingresar un valor negativo para un valor de latitud Sur o un valor de longitud Oeste. TI070 / TI071 / TI072 Latitude * Latitude Latitud (sec. 5.3.3) Hour setting Réglage de l’heure Ajuste de la hora or/ou Sunset or sunrise selection Sélection du coucher/lever du soleil Selección de la puesta o salida del sol Minutes setting Réglages des minutes Ajuste de los minutos or/ou Offset setting Réglage de l’écart Ajuste de la desviación Program start time Heure du début du programme Hora de comienzo del programa (sec. 5.4.3) 400-070-003-C 2008-04-09 1/2 400-070-003-C EFS.fm Page 2 Wednesday, April 9, 2008 8:56 AM Longitude/Latitude/Correction factor Longitude/Latitude/Facteur de correction Longitud/Latitud/Factor de corrección If your city is not listed below, use a nearby city or refer to the website “www.aubetech.com/timer”. Si votre ville n’est pas dans la liste, utiliser une ville avoisinante ou consulter le site web «www.aubetech.com/minuterie». Si su ciudad no figura en la lista, buscar una ciudad vecina o consultar el sitio web “www.aubetech.com/timer”. USA CANADA USA USA City Lat. Long. Adj. City Lat. Long. Adj. City Lat. Long. Adj. ABILENE 32 -99 1 LANSING 42 -84 1 SPRINGFIELD (MO) 37 -93 0 ALBUQUERQUE 35 -106 0 LAREDO 27 -99 1 ST. LOUIS 38 -90 0 ALLENTOWN 40 -75 0 LAS VEGAS 36 -115 0 SYRACUSE 43 -76 0 -101 1 LEXINGTON 38 -84 1 TALLAHASSEE 30 -84 1 -149 1 LINCOLN 40 -96 0 TAMPA 27 -82 0 -84 1 LITTLE ROCK 34 -92 0 TOLEDO 41 -83 1 30 -97 0 LONG BEACH 33 -118 0 TOPEKA 39 -95 0 35 -119 0 LOS ANGELES 34 -118 0 TUCSON 32 -110 0 36 -95 0 City / Ville Lat. Long. Adj. ABBOTSFORD 49 -122 0 BANFF 51 -115 1 BARRIE 44 -80 0 AMARILLO 35 BURNABY 49 -122 0 ANCHORAGE 61 CALGARY 51 -114 1 ATLANTA 33 AUSTIN CAPE BRETON 46 -60 0 BAKERSFIELD CHICOUTIMI 48 -71 0 BALTIMORE 39 -76 0 LOUISVILLE 38 -85 1 TULSA DAWSON 64 -139 1 BATON ROUGE 30 -91 0 LUBBOCK 33 -101 1 VIRGINIA BEACH 36 -75 0 BEAUMONT 30 -94 0 MACON 32 -83 1 WACO 31 -97 0 BILLINGS 45 -108 0 MADISON 43 -89 0 WASHINGTON DC 38 -77 0 BIRMINGHAM 33 -86 0 MEMPHIS 35 -90 0 WICHITA 37 -97 0 EASTMAIN 52 -78 0 EDMONTON 53 -113 1 FORT SEVERN 56 -87 1 BOISE 43 -116 1 MIAMI 25 -80 0 WINSTON-SALEM 36 -80 0 HALIFAX 44 -63 0 BOISE CITY 36 -102 1 MILWAUKEE 43 -87 0 YONKERS 40 -73 0 HAMILTON 49 -112 0 BOSTON 42 -71 0 MINNEAPOLIS 44 -93 0 YOUNGSTOWN 41 -80 0 BROWNSVILLE 25 -97 0 MOBILE 30 -88 0 IQALUIT 63 -68 0 INUKJUAK 58 -78 0 BUFFALO 42 -78 0 MODESTO 37 -120 0 CEDAR RAPIDS 41 -91 0 MONTGOMERY 32 -86 0 KELOWNA 50 -119 0 CHARLOTTE 35 -80 0 NASHVILLE 36 -86 0 KITCHENER 43 -80 0 CHATTANOOGA 35 -85 1 NEW ORLEANS 29 -90 0 LONDON 42 -81 0 CHEYENNE 41 -104 0 NEW YORK 40 -74 0 Ciudad Lat. Long. Adj. CHICAGO 41 -87 0 MISTASSINI 50 -73 0 NORFOLK 36 -76 0 TIJUANA 32 -117 0 CINCINNATI 39 -84 1 OKLAHOMA CITY 35 -97 0 NOGALES 31 -111 0 MONTREAL 45 -73 0 CLEVELAND 41 -81 0 OMAHA 41 -95 0 CIUDAD JUAREZ 31 -106 0 NIAGARA 43 -79 0 COLOMBUS 39 -82 0 ORLANDO 28 -81 0 MATAMOROS 26 -97 0 0 COLORADO SPRINGS 38 -104 0 OVERLAND PARK 38 -94 0 NUEVO LAREDO 27 -99 1 CORPUS CHRISTI 27 -97 0 OXNARD 34 -119 0 MONTERREY 25 -100 1 OSHAWA 43 -78 MÉXICO OTTAWA - GATINEAU 45 -75 0 DALLAS 32 -96 0 0 0 0 -89 -106 -71 40 28 46 PEORIA CHIHUAHUA QUEBEC DENVER 39 -104 0 PHILADELPHIA 40 -75 0 MAZATLÁN 23 -106 0 REGINA 50 -104 1 DES MOINES 41 -93 0 PHOENIX 33 -112 0 TAMPICO 22 -98 1 RICHMOND 49 -123 0 DETROIT 42 -83 1 PITTSBURG 40 -79 0 ZACATECAS 22 -102 1 ROUYN-NORANDA 48 -79 0 DULUTH 46 -92 0 PLANO 33 -96 0 LÉON 21 -101 1 EL PASO 31 -106 0 PORTLAND 45 -122 0 LA PAZ 24 -110 0 ERIE 42 -80 0 PROVIDENCE 41 -71 0 MEXICO CITY 19 -99 1 44 -123 0 RALEIGH 35 -78 0 PUEBLA 19 -98 1 1 SASKATOON 52 -106 1 SEPT-ILES 50 -66 -1 EUGENE SHERBROOKE 45 -71 0 EVANSVILLE 37 -87 0 RAPID CITY 44 -103 1 GUADALAJARA 20 -103 ST. ANTHONY 51 -55 0 FLINT 43 -83 1 RENO 39 -119 0 OAXACA 17 -96 0 ST CATHARINES 43 -79 0 FORT LAUDERDALE 26 -80 0 RICHMOND 37 -77 0 ACAPULCO 16 -100 1 FORT WAYNE 41 -85 1 0 0 0 -79 -86 -66 37 21 45 ROANOKE CANCUN SAINT JOHN (NB) FRESNO 36 -119 0 ROCHESTER 43 -77 0 MERIDA 21 -89 0 ST. JOHN'S (NFLD) 47 -52 0 GRAND RAPIDS 42 -85 1 ROCKFORD 42 -89 0 SUDBURY 46 -81 0 GREAT FALLS 47 -111 0 SACRAMENTO 38 -121 0 THUNDER BAY 48 -89 1 GREENSBORO 36 -79 0 SALT LAKE CITY 40 -111 0 HAMPTON 37 -76 0 TORONTO 43 -79 0 SAN ANTONIO 29 -98 1 HARTFORD 41 -72 0 SAN DIEGO 32 -117 0 TROIS-RIVIÈRES 46 -72 0 HONOLULU 21 -157 0 SAN FRANCISCO 37 -122 VANCOUVER 49 -123 0 HOUSTON 29 -95 0 SANTA ROSA 38 -122 VICTORIA 49 -123 0 HUNTSVILLE 34 -86 0 SAVANNAH 32 -81 0 INDIANAPOLIS 39 -86 1 SEATTLE 47 -122 0 JACKSON 32 -90 0 SHREVEPORT 32 -93 0 WHITEHORSE 60 -135 1 0 Lat. Long. Adj. 0 SAN JUAN 18 -66 0 WINDSOR 42 -83 1 JACKSONVILLE 30 -81 0 SOUTH BEND 41 -86 0 WINNIPEG 49 -97 0 KANSAS CITY 39 -94 0 SPOKANE 47 -117 0 YELLOWKNIFE 62 -114 1 KNOXVILLE 35 -83 1 SPRINGFIELD (IL) 39 -89 0 LAKEWOOD 39 -105 0 TI070 / TI071 / TI072 SPRINGFIELD (MA) 42 -72 PUERTO RICO Ciudad 0 REPÚBLICA DOMINICANA Ciudad Lat. Long. Adj. SANTO DOMINGO 18 -70 1 400-070-003-C 2008-04-09 2/2
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Copy, Annotate, Fill forms, Extract, Print high-res XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2008:07:25 15:59:30-04:00 Create Date : 2008:05:08 14:50:19-04:00 Metadata Date : 2008:07:25 15:59:30-04:00 Format : application/pdf Title : 400-072-000-C ENG.fm Creator : e283638 Document ID : uuid:426049ce-ca10-4535-845d-bf2adf3fe107 Instance ID : uuid:53b39e09-199c-4dc4-b214-3ce5d6bce4ef Page Count : 4 Author : e283638EXIF Metadata provided by EXIF.tools