Audio Technica R3100BD WIRELESS MICROPHONE RECEIVER User Manual

Audio-Technica Corporation WIRELESS MICROPHONE RECEIVER Users Manual

Users Manual

3000 SeriesFrequency-agile True Diversity UHF Wireless SystemInstallation and Operation3000 SeriesFrequency-agile True Diversity UHF Wireless SystemFrenchFrenchFrenchSpanishSpanishSpanishPortuguesePortuguesePortugueseGermanGermanGermanItalianItalianItalianDutchDutchDutchTraditional ChineseTraditional ChineseTraditional ChineseSimplified ChineseSimplified ChineseSimplified ChineseKoreanKoreanKoreanPOWERMODE/SETUHF SYNTHESIZED DIVERSITY RECEIVER ATW-R3100bALERT-TUNER-ABONOFF
3000 Series Installation and Operation (english)2This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.This device complies with INDUSTRY CANADA R.S.S. 210, en conformité avec IC: RSS-210/CNR210. Operation is subject to the following conditions: 1) This device may not cause harmful interference and 2) this device must accept any interference received, including interference which may cause undesired operation.CAUTION! Electrical shock can result from removal of the receiver cover. Refer servicing to qualied service personnel. No user-serviceable parts inside. • Do not expose batteries to excessive heat such as re, near heating units or in direct sunlight.• To prevent re or shock hazard, do not expose this product to rain or moisture.• To prevent re, do not place any naked ame sources (such as lighted candles) on the apparatus.• To prevent re, do not cover the ventilation of the apparatus with newspaper, tablecloths, curtains etc.• Do not expose this apparatus to drips or splashes.• Do not place any objects lled with liquids, such as vases, on the apparatus.• Do not install this apparatus in a conned space such as a bookcase or similar unit.• The apparatus should be located close enough to the AC outlet so that you can easily grasp the AC adapter at any time. In case of emergency, disconnect the AC adapter quickly.• Always consider environmental issues and follow your local regulations when disposing of batteries. Do not expose batteries to excessive heat.The circuits inside the receiver and transmitter have been precisely adjusted for optimum performance and compliance with federal regulations. Do not attempt to open the receiver or transmitter. To do so will void the warranty, and may cause improper operation. Notice to individuals with implanted cardiac pacemakers or AICD devices:Any source of RF (radio frequency) energy may interfere with normal functioning of the implanted device. All wireless microphones have low-power transmitters (less than 0.05 watts output) which are unlikely to cause difculty, especially if they are at least a few inches away. However, since a “body-pack” mic transmitter typically is placed against the body, we suggest attaching it at the belt, rather than in a shirt pocket where it may be immediately adjacent to the medical device. Note also that any medical-device disruption will cease when the RF transmitting source is turned off. Please contact your physician or medical-device provider if you have any questions, or experience any problems with the use of this or any other RF equipment.RF Interference Please note that wireless frequencies are shared with other radio services. According to Federal Communications Commission regulations, “Wireless microphone operations are unprotected from interference from other licensed operations in the band. If any interference is received by any Government or non Government operation, the wireless microphone must cease operation...” If you need assistance with operation or frequency selection, please contact your dealer or Audio-Technica. Thank you for choosing this Audio-Technica 3000 Series Frequency-agile True Diversity UHF Wireless System. The 3000 Series wireless system is available in six UHF frequency bands to provide exible performance in a wide variety of regions worldwide: Frequency Range Number of frequencies Band C 541.500 – 566.375 MHz 996 Band D 655.500 – 680.375 MHz 996 Band E 795.500 – 820.000 MHz 981 Band F 840.125 – 864.900 MHz 953 Band G 721.500 – 746.375 MHz 996 Band I 482.000 – 507.000 MHz 1001The band letter reference at the end of 3000 Series Stock Numbers indicates what band the system/component operates in. For simplicity, model numbers used throughout this manual will reference only the basic model number without the band indications. Each wireless system includes a receiver and either a body-pack or handheld transmitter. UniPak® body-pack transmitter systems may include an accessory microphone for a particular application. All A-T Wireless Essentials® microphones and cables, available separately, are pre-terminated for use with any Audio-Technica 3000 Series wireless system.All 3000 Series components feature soft-touch controls for quick, easy access to a formidable range of functions; an LCD information display in each unit provides convenient visual indication of unit settings and operation.The ATW-R3100b receiver is equipped with automatic frequency scanning for easy setup. It also features true diversity reception. Two antennas feed two completely independent RF sections on the same frequency; automatic logic circuitry continuously compares and selects the superior received signal, providing better sound quality and reducing the possibility of interference and dropouts. Soft-touch controls provide convenient access to a variety of functions, while a backlit LCD information display provides constant monitoring of system operation, including indication of the transmitter’s battery status. The receiver is half-width for a standard 1U 19" rack mount; rack-mount adapters are included. Two receivers can be mounted side by side, using an optional AT8630 joining-plate kit.The versatile ATW-T310b UniPak® body-pack transmitter has both low- and high-impedance inputs plus a bias connection, for use with dynamic and electret condenser microphones, as well as Hi-Z instrument pickups. In addition to its programmable functions, the transmitter features a three-position sliding cover to limit access, if desired, to just the Power/Mute button, or to cover all the controls, as appropriate for the application and user. The ATW-T341b handheld dynamic microphone/transmitter features the same element used in the Artist Elite® AE4100 dynamic handheld microphone created for professional livesound venues. The ATW-T371b handheld condenser microphone/transmitter features the same element used in the Artist Series ATM710 cardioid condenser vocal microphone.Transmitters in the 3000 Series use two 1.5V AA batteries for economical operation and wide availability. The receiver and both transmitters have “fuel gauge” battery condition indicators with low-battery warnings.An advanced Digital Tone Lock™ tone squelch system in the ATW-R3100b receiver opens only when a 3000 Series transmitter
3000 Series Installation and Operation (english)3is detected, reducing the possibility of interference. As a result, 3000 Series transmitters and receivers must be used together and should not be used with components from other Audio-Technica wireless systems, or with those of other manufacturers. Exception: 3000 Series components are compatible with Audio-Technica 1800 Series wireless system components.Please note that in multiple-system applications there must be a transmitter-receiver combination set to a separate frequency for each input desired (only one transmitter for each receiver). Because the wireless frequencies are within UHF TV frequency bands, only certain operating frequencies may be useable in a particular geographic area. Receiver Installation Location For best operation the receiver should be at least 3 ft. (1 m) above the ground and at least 3 ft. away from a wall or metal surface to minimize reections. The transmitter should be at least 3 ft. from the receiver, as shown in Figure A. Keep antennas away from noise sources such as digital equipment, motors, automobiles and neon lights, as well as away from large metal objects.Fig. AOutput ConnectionsThere are two audio outputs on the back panel: balanced and unbalanced. Use shielded audio cable for the connection between the receiver and the mixer. If the input of the mixer is a 1/4" jack, connect a cable from the 1/4" unbalanced audio output on the back of the receiver housing to the mixer. If the input of the mixer is an XLR-type input, connect a cable from the balanced XLR-type audio output on the back panel to the mixer. The two isolated audio outputs permit simultaneous feeds to both unbalanced and balanced inputs. For example, both a guitar amp and a mixer can be driven by the receiver.AntennasAttach the included pair of UHF antennas to the antenna input jacks. The antennas are normally positioned in the shape of a “V” (both 45° from vertical) for best reception.Antennas can be remotely located from the receiver. However, due to signal loss in cables at UHF frequencies, use the lowest-loss RF cables practical for any cable runs over 8 m/25 feet. RG8-type is a good choice. Use only copper-shielded cable, not CATV-type foil-shielded wire. Audio-Technica offers quality RF cables in four lengths, as well as remote antennas.Either passive or active antennas may be used. Both input jacks offer switchable +12 V DC output on their center pins to operate Audio-Technica powered antennas or other in-line RF devices if desired. Up to 60 mA can be drawn from each antenna input jack.Power Connections Connect the included AC adapter to the DC power input on the back of the receiver. Loop the small cord from the DC plug over the cord hook above the jack, to keep the plug from being detached by an accidental tug on the cord. Then plug the AC adapter into an AC power outlet. Operation of the receiver is controlled by the front-panel Power switch.Receiver Controls and FunctionsFront Panel Controls and Functions Fig. B1. POWER SWITCH: Press Power switch in and the receiver readouts will light.2. ALERT INDICATOR: The Alert Indicator lights: (a) When the receiver is in the Function Edit mode, (b) When no RF signal is received from transmitter, (c) When only one or two RF signal-strength bars are on, (d) When the transmitter is in the Mute mode, (e) When audio modulation level from the transmitter is close to the clipping point (AF +3/+6 bars), (f) When only one bar of the Battery “fuel gauge” is on (transmitter battery is weak).3. LCD WINDOW: Backlit screen indicates control settings and operational readings. See Figure D for examples.4. TUNER OPERATION INDICATOR: Indicates which Tuner (A or B) has the better reception and is in operation. The “B” indicator also lights to serve as conrmation of Mode/Set button entries.5. UP/DOWN BUTTONS: Press Up or Down arrow buttons, in conjunction with the Mode/Set button, to step through menus, select operating frequency and edit receiver function choices.6. MODE/SET BUTTON: Use in conjunction with the Up/Down arrow buttons to step through menus, choose operating frequency, initiate automatic scanning and select receiver function options. 7. MOUNTING ADAPTERS: For mounting the receiver in any standard 19" rack. Attach adapters to the receiver with the screws supplied and remove the four receiver feet. (Use optional AT8630 joining- plate kit to mount two ATW-R3100b receivers side-by-side.)Rear Panel Controls and Functions Fig. C8. ANTENNA INPUT JACK: BNC-type antenna connector for Tuner “B.” Attach the antenna directly, or extend it with a low-loss antenna cable.9. ANTENNA INPUT JACK: Input for Tuner “A.” Attach the antenna directly, or extend it with a low-loss antenna cable. 10. AF LEVEL CONTROL: Adjusts audio output level of both AF Output jacks; maximum output is fully clockwise.11. GROUND LIFT SWITCH: Disconnects the ground pin of the balanced output jack (12) from ground. Normally, the switch should POWERMODE/SETUHF SYNTHESIZED DIVERSITY RECEIVER ATW-R3100bALERT-TUNER-ABONOFFAF OUT UNBALANCEDAF OUT BALANCEDANT. AANT. BAF LEVELGROUND LIFT12~18V DC500 mAGROUNDPOWERMODE/SETUHF SYNTHESIZED DIVERSITY RECEIVER ATW-R3100bALERT-TUNER-ABONOFF1 2 3 4 5 68 9 1011 13 1415127
3000 Series Installation and Operation (english)4 be to the left (ground connected). If hum caused by a ground loop occurs, slide switch to the right (ground lifted).12. BALANCED AUDIO OUTPUT JACK: XLRM-type connector. A standard 2-conductor shielded cable can be used to connect the receiver output to a balanced microphone-level input on a mixer or integrated amplier.13. UNBALANCED AUDIO OUTPUT JACK: 1/4" phone jack. Can be connected to an unbalanced aux-level input of a mixer, guitar amp or tape recorder.14. POWER INPUT JACK: Connect the DC plug from the included in-line AC adapter.15. CORD HOOK: Loop the small DC cord around the cord hook to keep the DC plug from pulling out accidentally.Power On/Off To turn the receiver on, press in the Power switch. The Alert light and the LCD window will come on (about 1-2 seconds). The operating frequency will be displayed in the window after the power-up sequence. To turn the receiver off, press the Power switch again. LCD Window The LCD (Liquid Crystal Display) presents a great deal of setup and operating information clearly and conveniently. (See Figure D for examples.)Fig. DUp/Down Arrow Buttons In conjunction with the Mode/Set button, the arrow buttons permit moving through the menu of functions, and they offer a choice of settings within each function.Mode/Set Button The Mode/Set button shifts the receiver from normal operation into Menu mode and, in conjunction with the Up/Down arrow buttons, permits selection of different features and changing of their stored values in the Edit mode.How to Make Setting Changes1. From the normal operating mode, press the Mode/Set button once to enter the Function Menu mode. (Only the frequency will remain in the LCD window, and the receiver’s audio output will be cut off.)2. Use the Up/Down arrow buttons to reach the desired function. The value in the LCD window is the current setting for that function.3. Press the Mode/Set button once again to open the list of available choices for that function. The value will ash, indicating that it can be changed (Edit mode).4. Use the arrow buttons to go through the available choices, stopping on the desired new choice.5. (a) To accept and enter the new choice, press and hold the Mode/ Set button until “STORED” appears in the LCD. This changes the value and puts the function of the buttons back at Menu level (step 2 above). (The “B” tuner light will come on while the Mode/Set button is depressed, to conrm its action.) (b) To “back out” of the Edit mode without making a new choice, simply press the Mode/Set button once. The word “ESCAPE” will appear in the window and the function of the buttons will revert to the Menu level (step 2 above), without making any changes.6. Repeat this selection process for any other function changes desired. When nished with any changes, use the arrow buttons to move to “QUIT”. Press the Mode/Set button once to exit the menu and return the receiver to normal operation. (“RF” and “AF” will reappear in the window, indicating the return to normal receiver operation, with the receiver’s audio output again enabled.)Frequency Group SelectionTo select a frequency scan group, press the Mode/Set button, then use the arrow button until the desired group appears in the display. To store the selected frequency scan group, press the Mode/Set button to enter the desired group; then use the arrow button to start the scan. When a ashing number is displayed, press and hold Mode/Set button to select the frequency. See detailed instructions in System Operation.How to Restore Default SettingsTo return all the receiver functions to their original factory default settings, rst turn the receiver off. Then hold in the Mode/Set button while pressing and releasing the Power switch. The LCD will briey show “RESET”, followed by “WAIT” (release the Mode/Set button), before commencing normal-mode operation at the default settings.When the receiver is in the Menu or Edit mode, its audio output is silenced. Once control-setting operations are completed (or Escape is used), normal receiver operation will resume with its audio output restored. While in the Edit mode, if no action is taken for approximately 30 seconds (no buttons pressed), the receiver will “back out” to the Menu mode. Similarly, after about 30 seconds of inaction in the Menu mode, the receiver will “back out” to normal receiver operation with audio output restored. High-pass Filter Internal high-pass lter circuitry may be set to four positions: High-pass Off, or a 6 dB, 12 dB or 18 dB slope at 150 Hz. The default setting is Off (“HP OFF”). Increasing the slope of the high-pass lter further suppresses unwanted low frequencies, while maintaining the frequency response in the desired audio range.Meter Hold Setting When activated (“MH ON”), this function permits the bar-meters in the LCD window to capture and display the highest-level “AF” audio modulation (a solid bar) and the lowest-level “RF” signal (a ashing bar) received from the transmitter. This is particularly useful when setting up the system initially, during a sound-check, or when diagnosing operating problems. The default setting is Off (“MH OFF”).When the Meter Hold is On, it is possible to reset it – to obtain a new set of RF and AF readings – without turning it off-and-on using the Menu/Edit functions. Simply press the transmitter’s Power/Mute button once (to mute the transmitter) and wait until the receiver’s Alert light comes on, indicating the Mute condition. Then press the transmitter’s Power/Mute button once again, to un-mute the transmitter. After the Alert light goes out, a new set of min/max RF/AF readings will be indicated on the bar-meters. (Note that, depending upon the digital updating-and-conrming sequence of the Mute condition data from the transmitter, it may take several seconds for the Alert light condition to change. The Meter Hold function is not reset until the Alert light has turned on, then turned off.)Digital Tone Lock™ Squelch The 3000 Series employs a unique Digital Tone Lock squelch system that provides enhanced rejection of interference. In addition to providing highly effective control of unwanted noise, the Tone Lock signal from the transmitter also conveys data on the transmitter’s battery condition and mute status back to the receiver for display.BATTRF AFMHz87654321+6+30-3-6-9-16-20MHz MHzD1. Normal Receiver Operation (Transmitter off)D2. Menu Mode (Frequency) D3. Edit Mode (Frequency)ashing
3000 Series Installation and Operation (english)5The squelch level is adjustable from 15 dB (the default value) to 39 dB in 6 dB steps. Increasing the squelch level – also called “tightening the squelch” – can cause a reduction in useable range of the wireless transmitter, so use the lowest value that reliably mutes the unwanted RF signals. (If interference is a problem, rst consider trying a different frequency.)Antenna PowerThe antenna input jacks also can provide +12V DC output on their center pins to power inline RF devices. A maximum of 60 mA can be drawn from each of the jacks. While an accidental short-circuit will not harm the internal 12V supply, make certain that an antenna cable shield does not contact the center conductor. Antenna Power (“ANT.PWR”) is selected (switched on or off) from the LCD menu.Pre-coordinated Frequency Scan Groups 1-9The nine scan groups provided on the 3000 Series receivers simplify the selection of usable frequencies in a multi-channel wireless system. If you are using multiple systems, stay within one of the nine frequency groups for all of your systems. The available frequencies within each group have been selected for simultaneous use, eliminating the frustration encountered when trying to select compatible frequecies in a multi-channel system. Scan Groups 8 and 9 have been designed to allow for use on adjoining stages. Use Group 8 on one stage and Group 9 on a second nearby stage. Or use these two groups in two different rooms, with one room using Group 8, and the second using Group 9.Receiver FunctionsFunction Menu Default Setting* Choices (Edit)▲▼Wrap-around**(Receiver powers-up at Frequency)▲▼ Frequency Lowest in band†All frequenciesin bandYes▲▼ High-pass Filter HP OFF HP OFF, HP–6, HP–12, HP–18 No▲▼ Meter Hold MH OFF MH OFF MH ONYes▲▼ Squelch SQ 15 dB SQ 15 dB toSQ 39 dB in6 dB steps No▲▼ Antenna Power OFF PWR OFFPWR ONYes▲▼ Group 1 Lowest in frequency group All frequencies in Group 1No▲▼ Group 2 Lowest in frequency groupAll frequencies in Group 2No▲▼ Group 3 Lowest in frequency groupAll frequencies in Group 3 No▲▼ Group 4 Lowest in frequency groupAll frequencies in Group 4 No▲▼ Group 5 Lowest in frequency groupAll frequencies in Group 5 NoReceiver FunctionsFunction Menu Default Setting* Choices (Edit)▲▼Wrap-around**▲▼ Group 6 Lowest in frequency groupAll frequencies in Group 6 No▲▼ Group 7 Lowest in frequency groupAll frequencies in Group 7 No▲▼ Group 8 Lowest in frequency groupAll frequencies in Group 8 No▲▼ Group 9 Lowest in frequency groupAll frequencies in Group 9 No▲▼ Quit (exit Menu) QUIT Press Mode/Set to exit–* To reset to Default values, hold in the Mode/Set button while pressing the Power button to turn on the unit.** Continue in the same Up/Down direction and choices “wrap around” to the other end of the range.† Band I: 482.000 – 507.000 MHz; Band C: 541.500 – 566.375 MHz; Band D: 655.500 – 680.375 MHz; Band G: 721.500 – 746.375 MHz; Band E: 795.500 – 820.000 MHz; Band F: 840.125 – 864.900 MHz Transmitter Controls And FunctionsRefer to Figures E, F, G and H for an overview of transmitter features and controls.LCD WindowThe backlit Liquid Crystal Display presents a great deal of setup and operating information clearly and conveniently (See examples in Fig. J). The LCD in the transmitters is designed for greatest contrast and best viewing with the window rotated somewhat away from the viewer (about 30 degrees), not straight-on, for a more convenient holding/viewing position. The display is illuminated with a backlight when you power on the device and when you press Set to access transmitter functions. The backlight remains on during the Set process, only turning off if no action is taken within 30 seconds or if Quit is pressed; otherwise, it automatically turns off in ten seconds.Power/Mute Button The transmitters have a combination Power and Mute switch. When used in combination with the programmed choices explained below, the various functions available to the transmitter user may be tailored to t personal preferences or particular situations of use.Power On/OffTo turn the transmitter on, press and hold the Power/Mute button until the green power indicator and the LCD window come on (about 1-2 seconds). The operating frequency will show in the window after the power-up sequence.To turn the transmitter off, press and hold the Power/Mute button again, until the green power indicator and the LCD window are extinguished (about 1-2 seconds). The LCD window will show “PWR.OFF” before shutdown.Mute Off/OnWhen the transmitter is muted, it produces RF with no audio signal (continued)
3000 Series Installation and Operation (english)6modulation. When the transmitter is un-muted, it produces both RF and audio.To mute the transmitter (cut off the audio, but continue the RF output), press and release the Power/Mute button once. A small “MUTE” will appear in the LCD window, just below the frequency (Fig. M-2) and the power/mute LED will change from green to red.To un-mute the transmitter (restore the audio), press and release the Power/Mute button once again. The “MUTE” will disappear from the LCD window and the power/mute LED will change from red to green.Fig. EFig. FFig. GFig. HPower/Mute Locks Programmable Power/Mute Locks limit the functioning of the Power/Mute button as desired for particular users and/or applications. Power can be locked On; Mute can be locked Off. Selection of the desired locks, if any, is made through the function menu:Setting DescriptionNO.LOC The normal Power and Mute functions are fully operational.ALL.LOC Both the Power and Mute functions are locked into their status as of the time “ALL.LOC” is applied. (Power On, and Mute either On or Off.) Note: ALL.LOC must be re-accessed and the setting changed to turn the transmitter off.MUT.LOC In this mode, the audio cannot be muted. The Power functioning is unaffected. (If MUT.LOC is applied while the transmitter is muted, pressing the Power/Mute button once will return to un-muted operation; thereafter the Mute function is disabled until the setting is changed again.)PWR.LOC Power is locked On as of the time “PWR.LOC” is applied. The Mute functioning is unaffected. Note: When in the PWR.LOC mode, the transmitter may be turned off by: (1) Re-accessing the .LOC Menu and changing the setting, or (2) Removing and re-installing the batteries. When the transmitter is turned on again, it will power-up in the NO.LOC mode. (Only the PWR. LOC function will change when batteries are removed; all other settings remain stored in memory.)If an attempt is made to take an action that currently is lockedout, the LCD will display “LOCKED” briey, then return to itspreviously-displayed contents.Audio Input Selector The UniPak® body-pack transmitter provides input connections for both low-impedance (Lo-Z) microphones and high-impedance (Hi-Z) instruments. A wide range of Audio-Technica Wireless Essentials® microphones and cables is available pre-terminated with the appropriate professional latching connector. Selection of the desired input – microphone or instrument – is made through the function menu. Depending upon the input selected, a small “MIC” or “INST” will show in the LCD window, just below the frequency. (In the handheld transmitter, only “MIC” will show in the LCD window.)Frequency Group SelectionTo select a frequency scan group, press the Set button, then use the up or down arrow until the desired group appears in the display. To store the selected frequency scan group, press the Set button to enter the desired group; then use the arrow button to nd desired frequency. Press and hold Set button to select the frequency. See detailed instructions in System Operation.Restore Default Settings A “PRESET” selection in the menu permits resetting of all transmitter functions to their factory-default values.1. Press the Set button once to move to Menu mode.2. Press the Up arrow twice to move to “PRESET” in the LCD window.3. Press the Set button once and “LOAD” will appear in the LCD.4. Press and hold the Set button until “DEF” appears in the LCD.5. Press and hold the Set button until “LOADED” appears briey in the LCD. The window will then revert to “PRESET”.6. Press the Down arrow once to move to “QUIT”.7. Press the Set button once to exit the Menu mode and return to normal operation, with all factory-default settings restored.SETATW-T310b UHF TRANSMITTERBacklitLCD WindowAntennaPower-on LEDAudio Input JackPower/MuteButtonMounting ClipSet ButtonBatteryDoorUp/Down ArrowsSliding Control Cover (3-position) Band C: BlueBand D: GreenBand E: BlackBand F: GrayBand G: RedBand I: OrangeBacklit LCD WindowAntenna HousingPower-on LEDPower/MuteButtonBacklit LCD WindowPower-on LED Set ButtonUp/DownArrows
3000 Series Installation and Operation (english)7UniPak® Transmitter FunctionsFunction Menu Default Setting* Choices (Edit)▲▼Wrap-around(Transmitter powers-up at Frequency)▲▼ Frequency Lowest in band†All frequenciesin bandYes▲▼ RF Power RF LOW RF LOW, RF HI Yes▲▼ Audio Input Level +6 dB –6 dB, 0 dB, +6 dB, +12 dBNo▲▼ Power/Mute Locks NO.LOC NO.LOC, ALL.LOC, MUT.LOC, PWR.LOC Yes▲▼ Input Select MIC MIC, INST Yes▲▼ Group 1 Lowest in frequency groupAll frequencies in Group 1Yes▲▼ Group 2 Lowest in frequency groupAll frequencies in Group 2Yes▲▼ Group 3 Lowest in frequency groupAll frequencies in Group 3Yes▲▼ Group 4 Lowest in frequency groupAll frequencies in Group 4Yes▲▼ Group 5 Lowest in frequency groupAll frequencies in Group 5Yes▲▼ Group 6 Lowest in frequency groupAll frequencies in Group 6Yes▲▼ Group 7 Lowest in frequency groupAll frequencies in Group 7Yes▲▼ Group 8 Lowest in frequency groupAll frequencies in Group 8Yes▲▼ Group 9 Lowest in frequency groupAll frequencies in Group 9Yes▲▼ Reset to Defaults PRESET LOAD (b) hold until: DEF (c) hold until: LOADED–▲▼ Quit (exit Menu) QUIT Press Set to exit–Handheld Transmitter FunctionsFunction Menu Default Setting* Choices (Edit)▲▼Wrap-around**(Transmitter powers-up at Frequency)▲▼ Frequency Lowest in band†All frequenciesin bandYes▲▼ RF Power RF LOW RF LOW, RF HI Yes▲▼ Audio Input LevelDynamicCondenser**+6 dB+6 dB -6 dB, 0 dB, +6 dB, +12 dB,0 dB, +6 dB, +12 dB NoNo▲▼ Power/Mute Locks NO.LOC NO.LOC, ALL.LOC, MUT.LOC, PWR.LOCYes▲▼ Group 1 Lowest in frequency groupAll frequencies in Group 1Yes▲▼ Group 2 Lowest in frequency groupAll frequencies in Group 2Yes▲▼ Group 3 Lowest in frequency groupAll frequencies in Group 3Yes▲▼ Group 4 Lowest in frequency groupAll frequencies in Group 4Yes▲▼ Group 5 Lowest in frequency groupAll frequencies in Group 5Yes▲▼ Group 6 Lowest in frequency groupAll frequencies in Group 6Yes▲▼ Group 7 Lowest in frequency groupAll frequencies in Group 7 Yes▲▼ Group 8 Lowest in frequency groupAll frequencies in Group 8Yes▲▼ Group 9 Lowest in frequency groupAll frequencies in Group 9Yes▲▼ Reset to Defaults PRESET LOAD (b) hold until: DEF (c) hold until: LOADED--▲▼ Quit (exit Menu) QUIT Press Set to exit–* Continue in the same Up/Down direction and choices “wrap around” to the other end of the range.** Additional 6 dB pad switch on capsule.† Band I: 482.000 – 507.000 MHz; Band C: 541.500 – 566.375 MHz; Band D: 655.500 – 680.375 MHz; Band G: 721.500 – 746.375 MHz; Band E: 795.500 – 820.000 MHz; Band F: 840.125 – 864.900 MHz
3000 Series Installation and Operation (english)8Transmitter SetupBattery Selection and InstallationEach transmitter uses two 1.5V AA batteries, not included. Alkaline type is recommended; other types of 1.5V AA batteries (including rechargeable) may be used, however performance may vary. Always replace both batteries. Make certain the transmitter power is Off before replacing batteries.UniPak® Transmitter Battery Installation1. Open the battery compartment door as follows: Slide door lock down to the unlocked position. Pinch the release arrows together to open the compartment. (Fig. J) 2. Observe correct polarity as marked on the metal contacts on the door and carefully insert two fresh 1.5V AA alkaline batteries (Fig. K).3. Close the door, making certain the latch clicks securely in place.4. Slide the door lock up to the locked position.Fig. J Fig. KFig. LHandheld Transmitter Battery Installation 1. While holding the lower body cover (near the LCD window), grasp the upper part of the transmitter body just below the grille and unscrew it at least four complete turns (Fig. G); then slide the lower body cover down until it stops (Fig. H). Once the cover has been lowered, turn the transmitter over to reveal the battery compartment on the side opposite the LCD window.2. Observe correct polarity as marked inside the battery compartment and carefully insert two fresh 1.5V AA batteries (Fig. L). Insert the rst battery and slide it down. Then insert the second battery, bottom rst, into the space remaining. Make certain the batteries are fully seated in the battery compartment.3. Slide the lower body cover back up the body, then screw the housing together. Do not overtighten. Note: Remove batteries from the handheld transmitter starting at the bottom (– end) of the top battery (Fig. L). The top (+ end) of the top battery is captured in a recess and will not come straight out.Battery Condition IndicatorAfter the batteries are installed, turn the power on by pressing and holding the Power/Mute button. The small power-on LED (Fig. E/F) should light green and the LCD window should come on. If this does not happen, the batteries are installed incorrectly or they are dead. The transmitter’s “fuel gauge” battery indicator displays a maximum of four bar segments. When it ashes “LOW.BAT”, the batteries should be replaced immediately to ensure continued operation. (The receiver also displays transmitter battery condition in the LCD window with bar segments; the Alert indicator comes on to warn of a low-battery condition.)UniPak® Transmitter Input ConnectionConnect an audio input device (microphone or guitar cable) to the audio input jack on the transmitter. A number of Audio-Technica professional microphones and cables are available separately, pre-terminated with a UniPak input connector. The cable connector latches automatically when inserted into the transmitter jack. To unlatch and remove the connector, simply pull up on the connector’s knurled metal collar.UniPak® Transmitter AntennaThe UniPak transmitter includes a eld-replaceable exible antenna. For best results, allow the antenna to extend to its full length from the transmitter. If the received signal is marginal, experiment with different transmitter positions on your body or instrument; or try repositioning the receiver or using remote receiver antennas. Since the transmitter antenna simply screws in, check it occasionally to make certain it is snugly attached (nger-tight). Do not change the length of the transmitting antenna.Handheld Transmitter AntennaThe antenna for the handheld mic/transmitter is in the black, non-metallic section at the bottom of the unit (Fig. F). For best results, hold the mic/transmitter naturally, around its painted metal case; holding or otherwise covering the antenna housing may reduce the operating range.UniPak® Transmitter Mounting ClipThe UniPak transmitter’s mounting clip may be installed with the case positioned either “up” or “down,” depending upon which is preferred for the application. To turn the clip around, pull the ends of the clip out of the two holes on the sides of the transmitter case (Fig. E) and reinstall it facing in the opposite direction. Start from this endto remove batteriesSerial NumberReleaseArrowsDoor Lock
3000 Series Installation and Operation (english)9System OperationTurn the receiver on by pressing in the Power switch. Do not switch on the transmitter yet.The Alert indicator and the LCD window will light up; the normal-operation LCD display will appear after 1-2 seconds (Fig. D-1). If any of the bars show in the “RF” bar-graph meter, there may be RF interference in the area. If this occurs, select another frequency as explained below. (If the Meter Hold function has been selected, one of the RF bars will be ashing, indicating the lowest RF level received.)Selecting/Setting FrequencySelection of the desired operating frequency is made through the function menus. It’s usually best to start by setting the receiver’s frequency, to determine there is no local interference on that frequency. Then, always make certain to set the transmitter to the receiver’s exact frequency. The receiver’s unique Digital Tone Lock system squelches the audio only, permitting any RF energy on the frequency to show on the “RF” bar-meter.Note: It is often convenient to start with the factory-default frequency, if there is no RF energy showing on the RF bar meter. Using the Automatic Scan Function to Set Receiver Frequency1. Press the Mode/Set button once; then the “RF” and “AF” scales will disappear from the window and only the frequency will appear in the LCD window. (The receiver is now in the Menu mode.) See Figure D-2. 2. Use the Up arrow button to reach Group 1 through Group 9. Press the Mode/Set button once to select one of these nine scan groups. The lowest frequency in the selected scan group will appear in the LCD window. 3. Press the Up arrow button to begin the scan. “G SCAN” will ash in the LCD window.4. The rst available frequency will ash in the LCD window. To activate this frequency selection, press and hold the Mode/Set button until the word “STORED” appears in the LCD window. (If you do not wish to complete this particular selection, just press the Mode/Set button once. The word “ESCAPE” will appear briey in the window and the receiver will return to the Menu mode.)5. After you have activated your frequency selection (step 4), the “RF” and “AF” scales will reappear in the window, indicating the return to normal operation.6. If you are using multiple systems, all frequencies must be selected from the same group (Group 1 through Group 9). After completing the rst receiver’s scan and frequency selection, set the transmitter to the same frequency (see Setting Transmitter Frequency instructions); leave the transmitter On, and run the next receiver’s automatic scan function. Always set a receiver-transmitter pair to the same frequency before using the automatic scan function to select a frequency for the next receiver. “End” will show on the receiver display when no further usable frequencies remain in the selected scan plan.NOTES ON USING THE RECEIVER SCAN FEATURE:• Selecting low power on your transmitter can be helpful for multiple system setup, if you are experiencing problems with radio frequency interference.• To prevent raised noise oors that a receiver scan might interpret as radio frequency interference: during setup, keep all transmitters at least three feet apart and at least 15 feet from the receivers.Setting Receiver Frequency Manually 1. Press the Mode/Set button once; then only the frequency will appear in the LCD window. (The receiver is now in the Menu mode.) See Figure D-2.2. Press the Mode/Set button again; the Alert light will come on and the rst three digits of the frequency will ash in the window. (The receiver is now in the Edit mode, Fig. D-3.)3. Use the Up/Down arrow buttons to change the rst three digits (MHz) to the desired frequency. Choose a frequency appropriate for your area, avoiding frequencies with active TV channels. Press either arrow for single steps, or hold down either arrow for rapid cycling through the band. Frequencies “wrap around” to the other end of the range when the top or bottom of the band is reached. 4. Press the Mode/Set button once to set the rst three digits to the desired frequency. 5. Use the Up/Down arrow buttons to change the second three digits (kHz) to the desired frequency. Again, be certain to choose a frequency appropriate for your area, avoiding frequencies with active TV channels. 6. To activate this frequency selection, press and hold the Mode/Set button until the word “STORED” appears in the receiver’s window. (If you do not wish to complete this particular selection, just press the Mode/Set button once. The word “ESCAPE” will appear briey in the window and the receiver will return to the Menu mode.)7. When nished entering a frequency, press the Down arrow button once to move to “QUIT”. Then press the Mode/Set button once to exit the menu. The “RF” and “AF” scales will reappear in the window, indicating the return to normal operation.Transmitter On…Turn on the transmitter by pressing and holding the Power/Mute button (Fig. E/F) for a second or two, until the green power indicator and the LCD window have come on.Fig. MSetting Transmitter Frequency1. Press the Set button once and the small word “MENU” will appear above the frequency. Press the Set button again and the small ashing word “EDIT” will appear to the right of “MENU”. See Figures M-3 and M-4.2. Use the Up/Down arrow buttons to change the rst three digits of the transmitter frequency. Press either arrow for single steps, or hold down either arrow for rapid cycling through the range. Frequencies “wrap around” when the top or bottom of the band is reached. Select the exact frequency displayed on the receiver.3. Press the Set button once to set the rst three digits to the desired frequency.BATT MIC BATT MUTE MICBATT MICMENUBATT MICEDITM-1. Normal Operation * ATW-T310b only: “INST”M-3. Menu Mode (Frequency)M-2. Operation with Mute OnM-4. Edit Mode (Frequency)*
3000 Series Installation and Operation (english)104. Use the Up/Down arrow buttons to change the second three digits to the desired frequency.5. To activate this frequency selection, press and hold the Set button until the word “STORED” appears in the transmitter’s window. (If you do not wish to complete this selection, just press the Set button once: the word “ESCAPE” will appear briey in the window and the transmitter will return to the Menu mode.)6. When nished entering a frequency, press the Up arrow button once to move to “QUIT”. Then press the Set button once to exit the menu. The word “MENU” in the transmitter window will go off, indicating the return to normal operation.When the transmitter is switched on and in normal operation, the receiver’s “RF” signal-level bars will display from bottom to top, with more bars indicating increased signal reception. For optimum performance at least four, and preferably ve or more, of the RF indicators should be displayed.Setting Transmitter Audio Input LevelsCorrect adjustment of transmitter audio input, receiver audio output, and mixer/amplier input and output levels is important for optimum system performance.ATW-T310b and ATW-T341b TransmittersA 4-position audio input gain setting, selected through the function menu, serves to match the audio input level to the transmitter for best modulation with minimum distortion. Available choices are +12 dB, +6 dB, 0 dB and -6 dB. The default value is +6 dB. Select the highest setting that does not result in over-modulation with the highest audio/instrument input levels (an AF indication on the receiver no higher than “0”).ATW-T371b TransmitterA 3-position audio input gain setting, selected through the function menu, serves to match the audio input level to the transmitter for best modulation with minimum distortion. Available choices are +12 dB, +6 dB, and 0 dB. The default value is +6 dB. In addition, a mechanical pad switch on the condenser capsule (inside the screw-on wire mesh grille) can provide another 6 dB of attenuation. For best performance, adjust the input level using the function menu choices, keeping the capsule’s mechanical switch at 0 dB. If more audio attenuation is needed than the menu provides, then set the capsule’s pad switch to -6 dB.RF Power AdjustmentRF power may be set to “RF HI” (30 mW nominal) or “RF LOW” (10 mW nominal) through the function menu. The default setting is “RF LOW”. While the High setting normally provides maximum operating range, the Low setting will help extend battery life. The Low setting may also be preferred in multichannel systems, or when operating very close to the receiver, to reduce the possibility of interference or overload.RF InterferencePlease note that wireless frequencies are shared with other radio services. According to Federal Communications Commission regulations, “Wireless microphone operations are unprotected from interference from other licensed operations in the band. If any interference is received by any Government or non-Government operation, the wireless microphone must cease operation...” If you need assistance with operation or frequency selection, please contact your dealer or Audio-Technica. Ten Tips to Obtain the Best Results 1. Use only fresh alkaline batteries. Do not use “general purpose” (carbon-zinc) batteries.2. Position the receiver so that it has the fewest possible obstructions between it and the normal location of the transmitter. Line-of-sight is best.3. The transmitter and the receiver should be as close together as conveniently possible, but no closer than three feet (1 m).4. Avoid placing the receiver in a low or shielded location where the transmitter and receiver antennas are not within line-of-sight. If necessary, use remotely-located receiver antennas.5. Avoid placing the receiver near computers or other RF generating equipment.6. The receiver and transmitter must be set to the same frequency.7. A receiver cannot receive signals from two transmitters at the same time.8. Do not obstruct the handheld transmitter’s antenna (located at the base) or attached body-pack transmitter’s antenna with your hands.9. You need to change frequencies 1) when a strong interference signal is received, 2) when audio quality is poor due to weak RF, or 3) during multiple-system operation in order to select an interference-free frequency.10. Turn the transmitter off when not in use. Remove the batteries if the transmitter is not to be used for a period of time.
3000 Series Installation and Operation (english)11Troubleshooting GuideReceiver is not on (LCD window does not light). • Receiver Power switch is not pressed in. • Small DC power cord from included in-line power supply is not plugged into jack on back of receiver. (Use the cord hook to secure it.) • The in-line power supply is not plugged into AC power outlet. • AC power is not present at the AC outlet.Receiver is on (LCD window lights).- No sound - Alert light is OFF: 3 “RF”, “AF” and “BATT” legends do not appear in LCD. • Receiver is in the Menu mode. 3 “RF” and “AF” level meters both show good signals. • AF Level control on back of receiver not turned up (clockwise). Note: If the “AF” level meter shows a good signal on the receiver when the transmitter is receiving audio input, and the AF Level control is turned up, then the problem is in connections to or control settings on the mixer, amplier, etc. 3 Only “RF” level meter shows good signal; no “AF” signal. • No sound input to mic. • ATW-T310b body-pack only: Wrong input selected (“INST” or “MIC”).Receiver is on (LCD window lights).- No sound - Alert light is ON: 3 “RF”, “AF” and “BATT” legends do not appear in LCD, and LCD is ashing. • Receiver is in the Edit mode. 3 “RF” and “AF” level meters both show good signals. • The transmitter audio level is too high (“+3”/”+6” on receiver). • Batteries may be weak. (Check “BATT” fuel gauge.) 3 Only “RF” level meter shows good signal; no “AF”signal. • Transmitter may be muted. (Note: Normally it takes several seconds for the Alert light to turn off/on after the transmitter mute is switched off/on.) 3 Neither the “RF” nor the “AF” level meter shows any signal. • Receiver antennas not connected. • Transmitter is turned off. • Transmitter batteries are dead or missing. • Transmitter is set to a different frequency. • Transmitter and receiver not in same Band.Receiver is on (LCD window lights).- Distorted sound - Alert light is ON: 3 “RF” and/or “AF” level meters may show good signals. • The transmitter audio level is too high (“+3”/”+6” on receiver). • Received RF level may be too low (only one or two bars). • Batteries may be weak; check “BATT” fuel gauge. (Sound may or may not be distorted.)Momentary loss of sound/noisy sound as transmitter ismoved around performing area. • Transmitter and receiver antennas not in line-of-sight (or perhaps too far apart). Adjust positions of units so they are visible to each other/closer together; use remote antennas located closer to the transmitter location. • Signal blockage or interference from large metal objects, other wireless units located too close and/or on incompatible frequencies, computer or lighting equipment. • Squelch setting may be set “tighter” than it needs to be. (Recommended squelch setting is the minimum/default value, 15 dB.) Tip: Use the Meter Hold function to help identify and resolve (or at least avoid) RF problem locations.With transmitter on, received signal is noisy or containsextraneous sounds. • Batteries may be weak. Check “BATT” fuel gauge and “RF” meter level. • Local TV transmissions on this frequency. • Nearby sources of RF interference, such as computers, lighting equipment, etc. • Two transmitters may be operating on the same frequency. Locate and turn one off or change its frequency. • In multiple-system use, two (or more) incompatible frequencies may have been selected.Please note: This manual is offered in other languages at www.audio-technica.com
3000 Series Installation and Operation (english)12Specications†Overall SystemUHF Operating Frequencies Frequency Range Number of Frequencies Band C: 541.500 to 566.375 MHz 996 Band D: 655.500 to 680.375 MHz 996 Band E: 795.500 to 820.000 MHz 981 Band F: 840.125 to 864.900 MHz 953 Band G: 721.500 to 746.375 MHz 996 Band I: 482.000 to 507.000 MHz 1001 Not all frequencies are available in all areas. Please check with local regulations.Minimum Frequency Step 25 kHz Modulation Mode FM Maximum Deviation ±35 kHz Dynamic Range > 110 dB (A-weighted), typical Total Harmonic Distortion < 1% (at 1 kHz, ±17.5 kHz deviation) Operating Range 100 m (300'), typical Open range environment with no interfering signals. Operating Temperature Range -5 ºC to +45 ºC 23 º F to 113 ºF Battery and LCD performance may be reduced at very low temperatures. Frequency Response 70 Hz to 15 kHz (+1 dB, -3 dB) ATW-R3100b ReceiverReceiving System True diversityImage Rejection 60 dB nominal, 55 dB minimumRF Sensitivity 24 dBuV at 60 dB S/N ratio (50 ohms termination) Maximum Output Level XLR, balanced: +9 dBV ¼" (6.3 mm), unbalanced: +7 dBV Antenna Input BNC-type, 50 ohms Bias voltage 12V DC, 60 mA, each Power Requirements 12-18V DC, 500 mA Dimensions 210.0 mm (8.27") W x 164.4 mm (6.47") D x 44.0 mm (1.73") H Not including BNC connectors or feet. Net Weight 1.1 kg (38.8 oz), without accessories Accessories Included Two exible UHF antennas; AC adapter (country dependent); rack-mount adapters ATW-T310b UniPak® TransmitterRF Power Output High: 30 mW, Low: 10 mW (switchable), at 50 ohms Spurious Emissions Following federal and national regulations Input Connection Four-pin Locking Connector Pin 1: GND, Pin 2: INST INPUT, Pin 3: MIC INPUT, Pin 4: DC BIAS +5V Batteries Two 1.5V AA, not includedBattery Life High: 6 hours (alkaline) Low: 8 hours (alkaline) Depending on battery type and use pattern. Dimensions 66.0 mm (2.60") W x 24.0 mm (0.94") D x 87.0 mm (3.43") H Net Weight 81 g (2.9 oz), without batteries Handheld TransmittersRF Power Output High: 30 mW; Low: 10 mW, (switchable), at 50 ohmsSpurious Emissions Following federal and national regulations Microphone Element ATW-T341b Dynamic cardioid ATW-T371b Condenser cardioid Batteries Two 1.5V AA, not included Battery Life High: 6 hours (alkaline) Low: 8 hours (alkaline) Depending on battery type and use pattern. Dimensions ATW-T341b 237.0 mm (9.33") long, 48.0 mm (1.89") diameter ATW-T371b 240.0 mm (9.45") long, 50.0 mm (1.97") diameter Net Weight ATW-T341b 284 g (10.0 oz), without batteries ATW-T371b 277 g (9.8 oz), without batteries Accessory Included AT8456a Quiet-Flex™ stand clamp † In the interest of standards development, A.T.U.S. offers full details on its test methods to other industry professionals on request.Specications are subject to change without notice.CAUTION: U.S. Public Safety/Security Restrictions (Private Land Mobile Radio Services)Avoid the frequencies/channels listed below in each of the following U.S. metropolitan areas (as of November 2009). Refer to www.fcc.gov for updatesUrbanized AreaGeographical Center Bands (MHz) TV ChannelsNorth Latitude West LongitudeBoston, MA 42°21’24.4” 71°03’23.2” 470–476, 482–48814, 16Chicago, IL141°52’28.1” 87°38’22.2” 470–476, 476–48214, 15Cleveland, OH 241°29’51.2” 81°49’49.5” 470–476, 476–48214, 15Dallas/Fort Worth, TX32°47’09.5” 96°47’38.0” 482–488 16Detroit, MI 342°19’48.1” 83°02’56.7” 476–482, 482–48815, 16Houston, TX 29°45’26.8” 95°21’37.8” 488–494 17Los Angeles, CA 434°03’15.0” 118°14’31.3” 470–476, 482–488, 506–51214, 16, 20Miami, FL 25°46’38.4” 80°11’31.2” 470–476 14New York, NY/NE NJ40°45’06.4” 73°59’37.5” 470–476, 476–482, 482–48814, 15, 16Philadelphia, PA 39°56’58.4” 75°09’19.6” 500–506, 506–51219, 20Pittsburgh, PA 40°26’19.2” 79°59’59.2” 470–476, 494–50014, 18San Francisco/Oakland, CA37°46’38.7” 122°24’43.9” 482–488, 488–49416, 17Washington, DC/MD/VA38°53’51.4” 77°00’31.9” 488–494, 494–50017, 181 In the Chicago, IL, urbanized area, channel 15 frequencies may be used for paging operations in addition to low power base/mobile usages, where applicable protection requirements for ultrahigh frequency television stations are met.2 Channels 14 and 15 are not available in Cleveland, OH, until further order from the Commission.3 Channels 15 and 16 are not available in Detroit, MI, until further order from the Commission.4 Channel 16 is available in Los Angeles, CA, for use by eligibles in the Public Safety Radio Po
3000 Series Installation and Operation (english)13C-Band Scan Plan (541.500 – 566.375 MHz) Scan - 1 Scan - 2 Scan - 3 Scan - 4 Scan - 5 Scan - 6 Scan - 7 Scan - 8 Scan - 91542.750 541.500 541.500 548.125 541.500 541.700 542.750 541.500 541.7502545.500 542.750 542.125 548.375 541.900 542.100 543.250 542.000 542.2503547.125 544.375 543.500 548.875 543.000 544.775 543.500 543.250 543.5004547.375 544.750 544.000 549.125 544.975 546.225 544.500 544.750 545.0005549.750 545.750 546.250 550.375 546.025 546.975 545.250 545.250 545.5006550.375 547.500 548.250 550.625 548.700 548.900 546.500 546.000 546.2507550.625 554.250 549.750 551.125 549.500 550.100 547.500 546.500 546.7508557.250 556.125 555.750 551.375 549.900 552.775 548.250 554.300 554.5509557.500 557.500 556.625 556.650 560.225 554.975 558.750 559.125 559.37510 559.250 559.375 558.250 556.900 560.975 557.700 559.500 561.125 561.37511 559.500 560.000 559.375 557.400 562.025 561.500 560.500 561.625 561.87512 562.000 561.875 560.125 557.650 564.700 562.225 561.750 562.875 563.12513 563.375 562.250 561.500 558.900 565.100 564.500 562.500 564.375 564.62514 563.625 563.250 564.000 559.150 565.900 564.900 563.500 564.875 565.12515 566.000 565.500 564.250 559.650 566.300 565.700 563.750 565.625 565.87516 566.250 566.000 566.125 559.900 552.225 566.100 564.250 566.125 566.375D-Band Scan Plan (655.500 – 680.375 MHz) Scan - 1 Scan - 2 Scan - 3 Scan - 4 Scan - 5 Scan - 6 Scan - 7 Scan - 8 Scan - 91655.500 655.875 655.500 662.125 656.225 656.025 655.500 655.500 655.7502658.000 656.250 655.750 662.375 656.975 656.775 655.750 656.000 656.2503658.375 658.500 656.625 662.875 658.025 658.225 656.500 657.250 657.5004659.250 659.750 658.500 663.125 658.775 660.900 657.750 658.750 659.0005659.500 660.000 658.750 664.375 662.300 661.700 659.250 659.250 659.5006661.500 660.500 659.500 664.625 663.000 662.100 659.500 660.000 660.2507662.375 664.375 662.750 665.125 664.225 664.025 666.500 660.500 660.7508662.750 665.500 665.250 665.375 664.975 664.775 672.500 668.300 668.5509669.625 671.625 671.250 670.650 674.025 668.900 673.250 673.125 673.37510 671.750 672.000 672.375 670.900 674.775 669.300 675.750 675.125 675.37511 674.750 674.000 673.125 671.400 676.000 674.225 676.250 675.625 675.87512 675.750 674.500 674.125 671.650 676.700 674.975 678.750 676.875 677.12513 676.125 675.750 674.500 672.900 678.300 677.300 679.500 678.375 678.62514 678.000 676.750 675.375 673.150 679.000 678.100 679.750 678.875 679.12515 678.250 678.250 678.625 673.650 680.225 678.500 663.750 679.625 679.87516 679.500 680.250 679.125 673.900 668.700 680.025 675.500 680.125 680.375E-Band Scan Plan (795.500 – 820.000 MHz) Scan - 1 Scan - 2 Scan - 3 Scan - 4 Scan - 5 Scan - 6 Scan - 7 Scan - 8 Scan - 91798.925 798.900 795.550 798.250 795.825 796.000 796.500 795.500 795.7502800.525 799.475 796.775 799.200 796.950 796.700 796.900 796.000 796.2503801.475 801.425 797.050 799.900 797.500 797.100 797.700 796.750 797.0004803.025 802.025 797.750 802.825 798.600 797.900 800.775 797.250 797.5005803.550 803.075 806.850 803.350 802.425 806.300 806.100 798.250 798.5006804.825 803.625 807.400 808.900 809.325 807.000 806.500 798.750 799.0007805.150 806.925 811.100 809.725 810.425 810.775 810.225 799.500 799.7508811.700 809.125 811.725 811.350 811.250 812.700 810.975 800.000 800.2509812.825 811.575 813.050 812.100 811.825 813.500 812.500 809.150 809.40010 813.125 813.300 813.800 812.575 813.500 813.900 813.700 809.650 809.90011 816.625 815.425 799.400 800.900 813.900 800.975 798.100 810.400 810.65012 817.175 816.525 808.650 796.100 797.900 802.775 800.025 810.900 811.15013 817.425 817.100 813.300 801.725 806.600 808.225 813.300 811.900 812.15014 817.975 817.925 798.875 804.575 807.575 800.225 817.500 812.400 812.65015 819.050 818.225 804.825 807.200 808.050 808.975 818.225 813.150 813.40016 819.600 819.025 809.475 807.900 812.950 810.025 816.975 813.650 813.900F-Band Scan Plan (840.125 – 864.900 MHz)* Scan - 1 Scan - 2 Scan - 3 Scan - 4 Scan - 5 Scan - 6 Scan-7 Scan - 8 Scan - 91840.375 840.500 846.850 846.250 846.100 855.275 863.100 840.125 840.3752840.625 840.750 847.400 847.200 846.600 855.900 863.500 840.625 840.8753852.875 852.875 848.525 847.900 847.575 856.175 864.300 841.375 841.6254853.125 853.125 849.925 850.825 848.050 857.625 864.700 841.875 842.1255853.625 853.625 851.050 851.350 850.425 857.950 856.300 843.375 843.6256853.875 853.875 851.600 856.900 858.425 860.900 856.800 844.625 844.8757855.375 855.500 859.100 857.725 859.250 861.200 857.050 845.125 845.3758855.625 855.750 859.725 859.350 859.825 861.750 858.300 848.125 848.3759856.125 856.250 861.050 860.100 861.500 863.125 858.550 856.600 856.85010 856.375 856.500 861.800 860.575 861.900 863.375 859.050 857.100 857.35011 860.750 860.750 845.750 840.325 841.325 840.875 859.300 857.850 858.10012 861.000 861.000 861.300 842.825 843.250 841.125 840.375 858.350 858.60013 861.500 861.500 856.600 848.900 857.325 842.375 840.875 859.850 860.10014 861.750 861.750 857.950 848.325 843.825 842.625 842.375 860.350 860.60015 863.875 863.750 849.425 855.200 853.500 843.125 842.625 861.100 861.35016 864.125 864.000 852.850 863.650 855.575 843.375 843.375 861.600 861.850* When operating in the deregulated frequency range (863.000 –864.900 MHz) in countries following the R&TTE directive, transmitter power must be set to “LOW” (10 mW)G-Band Scan Plan (721.500 – 746.375 MHz) Scan - 1 Scan - 2 Scan - 3 Scan - 4 Scan - 5 Scan - 6 Scan - 7 Scan - 8 Scan - 91722.750 721.500 721.500 721.500 722.025 721.500 721.750 721.500 721.7502725.500 722.750 722.125 721.750 722.775 722.225 722.500 722.000 722.2503727.125 724.375 723.500 722.500 724.000 724.500 723.500 723.250 723.5004727.375 724.750 724.000 722.750 724.700 724.900 723.750 724.750 725.0005729.750 725.750 726.500 724.250 726.300 725.700 726.750 725.250 725.5006730.375 727.500 728.250 726.250 727.000 726.100 727.250 726.000 726.2507730.625 734.250 729.750 726.500 728.225 728.025 728.500 726.500 726.7508737.250 736.125 735.750 727.500 728.975 728.775 731.250 734.300 734.5509737.500 737.500 736.625 740.500 738.025 738.225 737.250 739.125 739.37510 739.250 739.375 738.250 741.500 738.775 738.975 739.500 741.125 741.37511 739.500 740.000 739.375 741.250 740.000 740.900 742.750 741.625 741.87512 742.000 741.875 740.125 742.250 740.700 741.300 743.500 742.875 743.12513 743.375 742.250 741.500 745.125 742.300 742.100 744.500 744.375 744.62514 743.625 743.250 744.000 745.375 743.000 744.025 745.250 744.875 745.12515 746.000 745.500 744.250 746.125 744.225 745.500 745.750 745.625 745.87516 746.250 746.000 746.125 746.375 744.975 746.225 739.250 746.125 746.375I-Band Scan Plan (482.000 – 507.000 MHz) Scan - 1 Scan - 2 Scan - 3 Scan - 4 Scan - 5 Scan - 6 Scan - 7 Scan - 8 Scan - 91482.100 482.225 482.225 488.125 482.025 482.225 482.500 482.000 482.2502482.350 482.475 482.475 488.375 482.775 482.975 483.250 482.500 482.7503483.100 483.225 483.225 488.875 484.000 484.500 483.500 483.750 484.0004483.350 483.475 483.475 489.125 484.700 485.300 484.250 485.250 485.5005484.850 484.975 484.975 490.375 486.300 485.700 486.750 485.750 486.0006486.850 486.975 486.975 490.625 487.000 486.500 487.250 486.500 486.7507487.100 487.225 487.225 491.125 488.225 488.025 489.750 487.000 487.2508488.100 488.225 494.150 491.375 488.975 488.775 495.500 494.800 495.0509501.000 500.875 497.275 502.650 498.025 498.225 497.250 499.625 499.87510 502.000 501.875 497.775 502.900 498.775 500.500 499.750 501.625 501.87511 502.250 502.125 498.025 503.400 500.000 500.900 500.250 502.125 502.37512 504.250 504.125 499.075 503.650 500.700 501.700 504.500 503.375 503.62513 505.750 505.625 499.325 504.900 504.225 502.100 505.250 504.875 505.12514 506.000 505.875 499.850 505.150 504.975 504.775 505.750 505.375 505.62515 506.750 506.625 506.625 505.650 506.025 506.225 506.500 506.125 506.37516 507.000 506.875 506.875 505.900 506.775 506.975 499.500 506.625 506.875
14WarrantyU.S. Two-Year Limited WarrantyThis product and selected Audio-Technica brand products purchased in the U.S.A. from an authorized Audio-Technica (A.T.U.S.) dealer are warranted for two years from date of purchase by A.T.U.S. to be free of defects in materials and workmanship. To identify those products, go to www.audio-technica.com/usawarranties. In event of a defect, End-User’s exclusive remedy is at A.T.U.S.’ election, the cost of repair, refund of the purchase price in the form of credit or cash, or replacement of the product. The product must be delivered to A.T.U.S. or an Authorized Service Center, prepaid, together with the sales slip or other proof of purchase date. This warranty excludes defects due to normal wear, abuse, shipping damage, or failure to use product in accordance with instructions. This warranty is void in the event of unauthorized repair or modication, or removal or defacing of the product labeling.For U.S. service return instructions and procedure please go to: www.audio-technica.com/returninstructions.A.T.U.S.’ warranty is to the End User only. Except for A.T.U.S.’ said express warranty, A.T.U.S. MAKES NO WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE PRODUCTS. A.T.U.S. SPECIFICALLY MAKES NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.Except to the extent precluded by applicable state law, A.T.U.S. IS NOT LIABLE FOR CONSEQUENTIAL, INCIDENTAL, DIRECT OR SPECIAL DAMAGES ARISING, DIRECTLY OR INDIRECTLY, IN RESPECT OF SUCH PRODUCTS OR USE OR FAILURE THEREOF, WHETHER BASED ON BREACH OF WARRANTY, NEGLIGENCE, STRICT LIABILITY, TORT OR OTHERWISE.This warranty gives you specic legal rights, and you may have other rights which vary from state to state.Outside the U.S.A., please contact your local dealer for warranty details.Audio-Technica U.S., Inc.1221 Commerce DriveStow, Ohio 44224UK and EU/Europe DisclaimerAudio-Technica operates a policy of continuous development. Audio-Technica reserves the right to make changes and improvements to any of the products described in this document without prior notice.Under no circumstances shall Audio-Technica be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused.The contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or contents of this document. Audio-Technica reserves the right to revise this document or withdraw it at any time without prior notice.The availability of particular products may vary by country. Please check with the dis-tributor for your territory. In some countries there may be restrictions in using this equip-ment. Please check with your local radio frequency authorities.Two-Years Limited Warranty Audio-Technica microphones and accessories purchased in the UK and EU / Europe are guaranteed for two years from date of purchase by Audio-Technica Ltd. to be free of defects in materials and workmanship. In the event of such defect, product will be repaired promptly without charge or, at our option, replaced with a new product of equal or superior value, if the faulty product is delivered to Audio-Technica Ltd., prepaid, together with the proof of purchase.Prior approval from Audio-Technica Ltd. is required for return. This warranty excludes defects due to normal wear, abuse, shipping damage, or failure to use product in accor-dance with instructions. This warranty is void in the event of unauthorized repair or modification.For return approval and shipping information, contact the Service Department, Audio-Technica Ltd. Tel: +44 (0)113 277 1441.Outside the U.K, please contact your local dealer for warranty details.
15
Audio-Technica U.S., Inc.1221 Commerce Drive, Stow, Ohio 44224 USA +1 (330) 686-2600Audio-Technica LimitedOld Lane, Leeds LS11 8AG England +44 (0) 113 277 1441Audio-Technica (Greater China) LimitedUnit K, 9/F., Kaiser Est. (Ph.2) 51 Man Yue St. Kowloon, HK. +852-2356-9268Audio-Technica (S.E.A.) Pte. Ltd.No 1 Ubi View, #01-14 Focus One, Singapore 408555 +65-6749-5686Audio-Technica Corporation2206, Naruse Machida, Tokyo Japan ©2010 Audio-Technica U.S., Inc. audio-technica.com P52165Disposal of Old Electrical & Electronic Equipment (Applicable in European countries with separate collection systems)This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city ofce, your household waste disposal service or the shop where you purchased the product.Deutsch Entsorgung von gebrauchten elektrischen und elektronischen Geräten (Anzuwenden in den europäischen Ländern mit einem separaten Sammelsystem für diese Geräte)Das Symbol auf dem Produkt oder seiner Verpackung weist darauf hin, dass dieses Produkt nicht als normaler Haushaltsabfall zu behandeln ist, sondern an einer Annahmestelle für das Recycling von elektrischen und elektronischen Geräten abgegeben werden muss. Durch Ihren Beitrag zum korrekten Entsorgen dieses Produkts schützen Sie die Umwelt und die Gesundheit Ihrer Mitmenschen. Umwelt und Gesundheit werden durch falsches Entsorgen gefährdet. Materialrecycling hilft den Verbrauch von Rohstoffen zu verringern. Weitere Informationen über das Recycling dieses Produkts erhalten Sie von Ihrer Gemeinde, den kommunalen Entsorgungsbetrieben oder dem Geschäft, in dem Sie das Produkt gekauft haben.Traitement des appareils électriques et électroniques en n de vie (Applicable dans les pays européens disposant de systèmes de collecte sélective)Ce symbole, apposé sur le produit ou sur son emballage, indique que ce produit ne doit pas être traité avec les déchets ménagers. Il doit être remis à un point de collecte approprié pour le recyclage des équipements électriques et électroniques. En s’assurant que ce produit est bien mis au rebut de manière appropriée, vous aiderez à prévenir les conséquences négatives potentielles pour l’environnement et la santé humaine. Le recyclage des matériaux aidera à conserver les ressources naturelles. Pour toute information supplémentaire au sujet du recyclage de ce produit, vous pouvez contacter votre municipalité, votre déchetterie ou le magasin où vous avez acheté le produit.Tratamiento de los equipos eléctricos y electrónicos al nal de su vida útil (Aplicable en países europeos con sistemas de recogida selectiva de residuos)Este símbolo en su equipo o su embalaje indica que el presente producto no puede ser tratado como residuos domésticos normales, sino que deben entregarse en el correspondiente punto de recogida de equipos eléctricos y electrónicos. Asegurándose de que este producto es desechado correctamente, Usted está ayudando a prevenir las consecuencias negativas para el medio ambiente y la salud humana que podrían derivarse de la incorrecta manipulación de este producto. El reciclaje de materiales ayuda a conservar los recursos naturales. Para recibir información detallada sobre el reciclaje de este producto, por favor, contacte con su ayuntamiento, su punto de recogida más cercano o el distribuidor donde adquirió el producto.Tratamento de Equipamentos Eléctricos e Electrônicos no nal da sua vida útil (Aplicável em países Europeus com sistemas de recolha independentes)Este símbolo no produto ou na sua embalagem indica que este não deve ser tratado como resíduo doméstico. Ao invés, será colocado no ponto de recolha destinado à reciclagem de equipamento eléctrico e electrônico. Assegurandose que este produto é despejado correctamente, você irá prevenir potenciais consequências negativas para o meio ambiente bem como para a saúde humana, que de outra forma poderiam ocorrer pela manipulação imprópria deste produto. A reciclagem dos materiais contribuirá para a conservação dos recursos naturais. Para obter mais informação detalhada sobre a reciclagem deste produto, por favor contacte o município acentos onde reside, os serviços de recolha de resíduos da sua área ou a loja onde o produto foi adquirido.Trattamento del dispositivo elettrico od elettronico (Applicabile in tutti I paesi dell’Unione Europea che utilizzano un sistema di raccolta differenziata)Questo simbolo sul prodotto o sulla confezione indica che il prodotto non deve essere riposto in un punto di raccolta adibito a riuti domestici. Deve invece essere trattato nel punto di raccolta appropriato per il riciclo di apparecchi elettrici ed elettronici. Assicurandovi che questo prodotto sia smaltito correttamente, contribuirete a prevenire potenziali conseguenze negative per l’ambiente e per la salute che potrebbero altrimenti essere causate dal uno smaltimento inadeguato. Il riciclaggio dei materiali aiuta a conservare le risorse naturali. Per informazioni più dettagliate circa il riciclaggio di questo prodotto, potete contattare il vostro ufcio comunale, il servizio locale di smaltimento riuti oppure il negozio dove l’avete acquistato.Verwijdering van oude Elektrische en Elektronische Apparaten (Toepasbaar in de Europese landen met gescheiden ophaalsysteem)Het symbool op het product of op de verpakking wijst erop dat dit product niet als huishoudafval mag worden behandeld. Het moet echter naar een plaats worden gebracht waar elektrische en elektronische apparatuur wordt gerecycled. Als u ervoor zorgt dat dit product op de correcte manier wordt verwijderd, voorkomt u voor mens en milieu negatieve gevolgen die zich zouden kunnen voordoen in geval van verkeerde afvalbehandeling. De recyclage van materialen draagt bij tot het vrijwaren van natuurlijke bronnen. Voor meer details in verband met het recyclen van dit product, neemt u het best contact op met de gemeentelijke instanties, het bedrijf of de dienst belast met de verwijdering van huishoudafval of de winkel waar u het product hebt gekocht.Håndtering af udtjent elektrisk og elektronisk udstyr (Gælder for europæiske lande med separate indsamlingssystemer)Dette symbol på produktet eller emballagen angiver, at produktet ikke må behandles som husholdningsaffald. Det skal i stedet indleveres på en deponeringsplads specielt indrettet til modtagelse og genbrug af elektrisk og elektronisk udstyr. Ved at sikre, at produktet bortskaffes korrekt, forebygges de eventuelle negative miljø- og sundhedsskadelige påvirkninger, som en ukorrekt affaldshåndtering af produktet kan forårsage. Genbrug af materialer vil medvirke til at bevare naturens ressourcer. Yderligere information om genbrug af dette produkt kan fås hos myndighederne, det lokale renovationsselskab eller i butikken, hvor produktet blev købt.Omhändertagande av gamla elektriska och elektroniska produkter (användbara i europeiska länder med separata insamlingssystem)Symbolen på produkten eller emballaget anger att produkten inte får hanteras som hushållsavfall. Den skall i stället lämnas in på uppsamlingsplats för återvinning av el- och elektronikkomponenter. Genom att säkerställa att produkten hanteras på rätt sätt bidrar du till att förebygga eventuella negativa miljö- och hälsoeffekter som kan uppstå om produkten kasseras som vanligt avfall. Återvinning av material hjälper till att bibehålla naturens resurser. För ytterligare upplysningar om återvinning bör du kontakta lokala myndigheter eller sophämtningstjänst eller affären där du köpte varan.Pozbywanie się zużytego sprzętu (Stosowane w krajach europejskich posiadających system selektywnej zbiórki odpadów)Takie oznaczenie na produkcie lub jego opakowaniu wskazuje, że produkt nie może być traktowany jako odpad komunalny lecz powinno się go dostarczyć do odpowiedniego punktu zbiórki sprzętu elektrycznego i elektronicznego w celu recyklingu. Zapewniając prawidłową dyspozycję dotyczącą produktu, zapobiega się jego negatywnemu działaniu na środowisko oraz zdrowie ludzi, jakie mogłoby wystąpić w przypadku niewłaściwego postępowania. Recykling materiałów pomoże w ochronie bogactw naturalnych. W celu uzyskania bardziej szczegółowych informacji na temat recyklingu tego produktu, należy skontaktować się urzędem miejskim, ze służbami oczyszczania miasta lub ze sklepem, w którym ten produkt został zakupiony.Утилизация электрического и электронного оборудования (директива применяется в странах, где действуют система раздельного сбора отходов).Данный знак на устройстве или его упаковке обозначает, что данное устройство нельзя утилизировать вместе с прочими бытовыми отходами. Его следует сдать в соответствующий приемный пункт переработки электрического и электронного оборудования. Неправильная утилизация данного изделия может привести к потенциально негативному влиянию на окружающую среду и здоровье людей, поэтому для предотвращения подобных последствий необходимо выполнять специальные требования по утилизации этого изделия. Переработка данных материалов поможет сохранить природные ресурсы. Для получения более подробной информации о переработке этого изделия обратитесь в местные органы городского управления, службу сбора бытовых отходов или в магазин, где было приобретено изделие.Käytöstä poistetun sähkö- ja elektroniikkalaitteen hävitys (Euroopan maiden keräysjärjestelmät)Symboli, joka on merkitty tuotteeseen tai sen pakkaukseen, osoittaa, että tätä tuotetta ei saa käsitellä talousjätteenä. Tuote on sen sijaan luovutettava sopivaan sähkö-ja elektroniikkalaitteiden kierrätyksestä huolehtivaan keräyspisteeseen. Tämän tuotteen asianmukaisen hävittämisen varmistamisella autetaan estämään sen mahdolliset ympäristöön ja terveyteen kohdistuvat hailtavaikutukset, joita voi aiheutua muussa tapauksessa tämän epäasianmukaisesta jätekäsittelystä. Materiaalien kierrätys säästää luonnonvaroja. Tarkempia tietoja tämän tuotteen kierrättämisestä saa paikallisesta kunnantoimistosta.

Navigation menu