Audio Technica SPORT4 Bluetooth Wireless Stereo Headset User Manual ATH CKS55XBT EX Instructions 1
Audio-Technica Corporation Bluetooth Wireless Stereo Headset ATH CKS55XBT EX Instructions 1
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2611888 |
| Application ID | +9OX5gK9lAnGIlxn3X9cSg== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 70.27kB (878323 bits) |
| Date Submitted | 2015-05-12 00:00:00 |
| Date Available | 2015-05-12 00:00:00 |
| Creation Date | 2015-05-01 14:58:58 |
| Producing Software | Adobe PDF library 9.90 |
| Document Lastmod | 2015-05-01 15:39:22 |
| Document Title | æ–°ATH-CKS55XBT EX_Instructions_1 |
| Document Creator | Adobe Illustrator CS5 |
ATH-SPORT4 Instruction booklet ATH-SPORT4 Wireless stereo headphones Manuel d'utilisateur ATH-SPORT4 Casque stéréo sans fil Libretto di istruzioni ATH-SPORT4 Cuffie estéreo inalámbrico English CAUTIONS Thank you for purchasing this wireless stereo headset. Please keep this manual handy, along with the warranty, so they are always available for reference. Please read these cautions before using your headphones. To ensure safety, observe all cautions while using this equipment. For customers in the USA FCC Notice Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and(2) this device must accept any interference received, including interference that may cause undesired operation. Caution You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: − Reorient or relocate the receiving antenna. − Increase the separation between the equipment and receiver. − Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. − Consult the dealer or an experienced radio/TV technician for help. For customers in Canada IC statement This device complies with INDUSTRY CANADA R.S.S. 210, en conformité avec IC: RSS-210/CNR210. Operation is subject to the following conditions: (1) This device may not cause harmful interference and(2) this device must accept any interference received, including interference which may cause undesired operation. CAN ICES-3 (B)/NMB-3(B) Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. English CAUTIONS ● Do not use the headphones near medical equipment. Radio waves may affect cardiac pacemakers and medical electronic equipment. Do not use the product inside medical facilities. ● Do not use the headphones in aircrafts. Radio waves may affect electronic equipment and cause accidents due to malfunction. ● Do not use the headphones near automatic control devices such as automatic doors and fire alarms. Radio waves may affect electronic equipment and cause accidents due to malfunction. ● Do not disassemble, modify or attempt to repair the headphones. ● Do not subject the headphones to strong impact. ● Disconnect this product from the computer if you find any malfunction like noise, smoke, smell, heat or damage on the product. In this case, contact your local Audio-Technica dealer or service center. ● To prevent fire or shock hazard, do not expose this apparatus to rain or moisture. ● Do not cover with a cloth. ● Follow applicable laws regarding mobile phone and headphone use if using headphones while driving. ● Do not use the headphones in places where the inability to hear ambient sound presents a serious risk (such as at railroad crossings, train stations, construction sites). ● Store the earpieces out of the reach of small children. ● If you begin to feel unwell while using this product, please discontinue use immediately. ● To prevent damage to your hearing, do not raise the volume too high. Listening to loud sound for an extended period may cause temporary or permanent hearing loss. ● Discontinue use if skin irritation results from direct contact with the product. ● When removing the headphones from your ears, check to make sure the earpieces are still attached to the main unit. If the earpieces become lodged in your ears and you are unable to remove them, consult a physician at once. ● The earphones are designed to plug your ear cavities. If you feel any discomfort, temporarily discontinue use. English CAUTIONS Caution for rechargeable battery ● If battery fluid gets into eyes, do not rub the eyes. Rinse thoroughly with clean water such as tap water and consult a doctor immediately. ● If battery fluid leaks, do not touch fluid with bare hands. our service center. immediately. water. If you feel uncomfortable with your skin, consult a doctor. ● Never dispose of the battery in a fire, heat, disassemble or modify the battery. Failure to observe this caution could cause leakage, generation of heat or explosion. ● Do not attempt to pierce with a nail, hit with a hammer or step on the battery. Failure to observe this caution could cause generation of heat, damage or ignition. ● Do not attempt to drop or give strong impact to the battery. Failure to observe this caution could cause leakage, generation of heat or explosion. ● Do not use, leave or store the battery in the following places. ■ Place exposed to direct sunlight or high-temperature and humidity ■ Inside of a car under the blazing sun ■ Near heat sources such as heater Failure to observe this caution could cause leakage, generation of heat, explosion or performance degradation. ● Do not get the battery wet. Failure to observe this caution could cause generation of heat, explosion or ignition. ● Do not charge with a charger other than the included (specified) USB cable for charge. Failure to observe this caution could cause malfunction or fire. ● After using the device, be sure to switch off. Leakage often occurs due to battery drain as a result of failure to switch off. PRECAUTIONS ● Be sure to read the operation manual for the Bluetooth device before use. ● Audio-Technica will not be liable in any way for any loss of data in the unlikely event that such losses should occur while using this product. ● On public transport systems or in other public places, keep the volume low so as not to disturb other people. ● Please minimize the volume on your audio device before connecting the headphones in order to avoid hearing damage from sudden exposure to excessive volume. ● When using this product in a dry environment, you may feel a tingling sensation in your ears. This is caused by static electricity accumulated on your body, not by a headphone malfunction. ● Do not store the headphones under direct sunlight, near heating devices or in a hot, humid or dusty place. Do not allow the headphones to get wet. English PRECAUTIONS ● When this product is used for a long time, the headphones may become discolored due to ultraviolet light (especially direct sunlight) or wear. ● The cable may become caught or severed if product is placed in a bag or pocket without adequate protection. To carry the product,use the accessary pouch. ● To prevent wire break please don’t loop the headphone cable around another device. ● Connect/disconnect the cable by holding the plug. Pulling directly on the cable can result in a broken wire and the risk of electric shock. ● Reception on the headphones is available only through the mobile telephone network. Please note that performance of other types of phone reception (phones using other wireless applications) cannot be guaranteed. ● If you use the headphones close to an electronic device or transmitter (such as mobile phone), a noise may be caused in the headphones. In this case, keep it away from the electronic device or transmitter. ● If you use the headphones near a TV or radio antenna, noise may be caused in the television or radio. In this case, keep it away from the TV or radio antenna. ● To protect the built-in rechargeable battery, charge it at least once every half year. If you leave it too long, you will have less rechargeable battery life or the battery may not recharge at all. ● These headphones are not completely waterproof. Do not deliberately submerge them in water or use in water. If the headphones become dirty, for to the "Cleaning" instructions and clean the headphones. ● These headphones are not designed to be moisture proof. Do not use them in places where there is high humidity (such as bathrooms or saunas). Failure to observe this caution could cause malfunction. ● Do not bend the flexible ear hangers more than necessary. Failure to observe this caution could result in damage. ● If you do not intend to use these headphones for a prolonged period, store in a well-ventilated location away from high temperatures and humidity. ● Do not leave inside a car parked in direct sunlight. Failure to observe this caution could cause malfunction. Simultaneous use with other devices Failure, such as the interruption of sound, may be caused by radio wave interference from devices that use the same frequency band (2.4GHz) as the headphones, including Bluetooth-enabled devices, devices using wireless LAN, digital cordless phones and microwaves. Similarly, because radio waves of the headphones may affect these devices, take the following precautions: - Install the devices using the same frequency band (2.4GHz) as the headphones away from the headphones. - Do not use the product in hospitals, trains and aircrafts. Instructions for Use Any device which is connected to the headphones needs to meet the Bluetooth standards established by Bluetooth SIG and be certified. Even if the device meets the Bluetooth standards, it may not connect to the headphones or the operation method and behavior may differ depending on its characteristics and specification. English Part names Right Bush Left Flexible ear hanger Microphone Indicator Micro USB jack The left earpiece has a protruding part. USB cap Housing Back Volume button Control button Remote controller L/R Earpiece Cable slider Waterproof Function These headphones are designed to prevent perspiration from exercising or water from simple washing from getting inside the headphones. (IPX5 equivalent) Never purposely use in water or allow liquids other than water or perspiration (such as soapy water) to come into contact with the headphones as doing so will cause a malfunction. Also, be sure to check that the USB cap is fully closed to ensure the headphones are water resistant. * Water may get inside the headphones if the USB cap is not fully closed. English How to Charge When the rechargeable battery power runs low, you will hear a short beep and the indicator will It takes about 3 hours to charge the battery fully. (It varies depending on service conditions.) * The headphones cannot be used during charging because Bluetooth is disconnected. Connect the included USB cable (the Micro USB terminal side) to the headphone Micro USB jack. * Only use with the provided USB cable for charging. * Do not forcefully insert the cable as doing so may cause damage. Micro USB jack USB port Micro USB terminal Computer TypeA USB charging cable (included) Connect the USB cable (the Type A side) to the computer and start charging. Lit red :Charging Lit blue :Charging complete * Check that the indicator is lit to make sure charging has started. Briefly press the Control button if charging has not started. * The provided USB cable for charging and inside of the USB cap are not water resistant. Make sure they do not get wet. Be sure to close the USB cap. How to Connect About Pairing To connect the headphones to a Bluetooth device, the headphones needs to pair (register) with the device. Once it is paired, you don't need to pair it again. However, you will need to pair again in the following cases: ・If the headphones is deleted from the Bluetooth device connection history, ・If the headphones is sent out for repair, ・If the headphones is paired with 9 devices or more. (The headphones can be paired with up to 8 devices. When you pair with a new device after pairing with8 devices, pairing information for the device with the oldest connection date will be overwritten by information for the new device.) English How to Connect How to Perform Pairing * Read the user manual for the Bluetooth device. * Place the Bluetooth device within 1 meter of the headphones to perform pairing correctly. * Wear the headphones to confirm pairing by listening for sound. Starting with the headphones turned off, press and hold the Oontrol button on the Bluetooth transmitter/receiver for about 5 seconds. Long press Beep (Pi-PoPPo) ♪ sound Pairing process will begin and the Bluetooth device will search for the headphones. * For more information on how to use the Bluetooth device, read the operation manual for the device. When the headphones is searched for, "ATH-SPORT4" will display on the Bluetooth device. Select "ATH-SPORT4" and register the device to be connected. Some devices may ask for pass key*. In this case, enter "0000". ON Device ATH-SPORT4 Select * The pass key is also called pass code, PIN code, PIN number or password. When the headphones rings, the pairing has performed normally and been successfully completed. Beep (Pu-Pu-) ♪ sound English About Indicator Display The indicator of the headphones indicates the following operating status by flashing or turning on. Indicator display patterns Operating status Pairing Connect Red Blue ＊ Searching for device Waiting to be connected Flashing Connecting Remaining Remaining battery battery level level low Charging Lit Full charge Led off Charge *The lamp flashes red rapidly if you pair a device when the remaining battery level is low. How to Use The headphones is capable of making Bluetooth connections, playing music and receiving incoming calls. Please use the headphones in accordance with applications. Please note that we cannot guarantee the operation of applications of the Bluetooth device. Power supply ON : Press and hold the Control button (for about 3 seconds) to turn on the power. Beep (PipoPa-) ♪ sound (Indicator: blue) Long press *If these headphones are switched to pairing mode by mistake, turn the power off and on again. OFF : When the power is on, press and hold the Cotrol button (for about 3 seconds) to shut off the power. Beep (Pu-Pi-) ♪ sound (Indicator: red) English How to Use How to Wear Pass the cable around the back of your neck. As shown in the figure on the right, check the L/R symbols with the bush facing upwards and fit the headphones onto your ears. Adjust the flexible ear hangers to fit around the back of your ears after fitting the headphones for a stable, comfortable fit. *Do not bend the flexible ear hangers more than necessary at this time. Failure to observe this caution could cause malfunction. Bush Headphones ■ Cable slider Pass the cable around the back of your neck, and slide the cable slider to the bottom of your neck to loosely hold the cable in place. ■ 2 Types of Earpiece Cable slider Two types of earpiece are provided with these headphones. Check the features of each type and use according to the conditions where you are using the headphones. Fine fit earpiece Active fit earpiece Standard earpieces that seal tightly and prevent sound leak. Earpieces designed with an uneven surface to allow external sounds to be heard easily. * * These earpieces are designed so that external sounds are easier to hear, but please be careful of the surrounding environment when using outdoors. * For details on how to replace earpieces, see "About the earpieces" -> "Replacing the earpieces". Listening to Music To connect for the first time, refer to ”How to Connect”and pair the headphones with a Bluetooth device and connect. Once pairing has been performed, turn on the headphones and turn on the Bluetooth connection of the Bluetooth device. Play and enjoy music according to the operation manual of the Bluetooth device connected. The following operations are available on the headphones: Control button Short press Play/Pause Plays or pauses music and video. + button Volume button + button - button 10 Short press Volume Up The volume turns up by one level. ** Long press* Forward Forwards to the next track. Short press Volume Down The volume turns down by one level. ** Long press* Rewind Returns to the previous track. * 1 Press and hold for approximately 1 second, then release when - button you hear the sound of a short beep. ** You will hear a short "beep" when the volume reaches its maximum/minimum. English How to Use Taking a Call If telephone function is incorporated in the Bluetooth device, you can make a call using the headphones. When the Bluetooth device receives a call, you will hear the headphones ring. When you get a call while listening to music, the music will stop. When you end the call, the music will resume. Control button * There are some Bluetooth devices on which audio playback cannot be restarted. Taking a call Ending a call Changing call volume During the call, you can turn the volume up or down by pressing the Volume button (+/−). Switching a Call between the headphones and Mobile Phone Every time you press the Control button holding the Volume button(+）during a call, you will toggle between accessing the call via the mobile phone and accessing it via the headphones. Blocking communications During an incoming call, briefly press Control button while holding down the volume button (+) to reject the incoming call. 11 English About the earpieces Sizes and position It may be difficult to hear the bass sounds if the earpieces do not fit snugly into your ears. These headphones come with fine fit earpieces in foursizes (XS, S, M and L) and active fit earpieces in three sizes (S, M and L). At the time of purchase, the M size fine fit earpieces are attached to the headphones. To enjoy the best sound quality and comfort, you should experiment with the size of the earpieces to find the best fit for you. If the headphones are not properly fitted to your ears, audio quality may be diminished. Cleaning the earpieces Remove earpieces from the headphones and clean them with a diluted detergent. After cleaning, dry before use. Replacing the earpieces Remove each old earpiece, and mount the new earpiece over the stem up to the base of the stem. Note: ・Periodically remove and clean the earpieces as they become dirty easily. Using with dirty earpieces may cause the headphones to become dirty through the earpieces, resulting in deteriorated sound quality. ・Earpieces are consumable parts which degrade through storage and use. lf the fit has become loose or if the earpieces appear to have degraded, purchase replacements. ・When reattaching earpieces to the headphones, be sure to check that they are securely attached. Injury or illness may occur if the earpieces are left inside the ear. 12 English Cleaning Please clean these headphones regularly to ensure long lasting use. Do not use solvents such as alcohol or thinner when cleaning these headphones. About These Headphones If these headphones become dirty with perspiration or dust, etc., wash in fresh water at a normal temperature (10 - 35℃) or rinse under a gentle tap water stream. Do not allow water to come directly into contact with the "parts where sound is output" (non-waterproof area). * Before washing, be sure to check that the micro USB jack cap is tightly closed. * Wash by hand. Do not use a brush or sponge. * Rinse from the housing side. These headphones are treated with IPX5 equivalent waterproofing, but the parts where sound is output are non-waterproof areas. Sound may not be output or may be difficult to hear if water gets inside the headphones. Water flow direction Parts where sound is output" (non-waterproof area) Housing ● Microphone section Wipe using the following procedure after washing. 12 Thoroughly wipe away any surface water using a soft, clean and dry cloth. Hold the headphones firmly and shake approximately 20 times to shake off any water droplets. Sound may not be output if moisture still remains in the "parts where sound is output" and "microphone section". In this case, place the headphones on a dry cloth as shown in the figure on the right, and shake each side approximately 20 times with the "parts where sound is output" and "microphone section" facing downwards. Press a soft, clean and dry cloth onto the gaps such as the "parts where sound is output" and "microphone section" to soak up any remaining water. Dry in a well ventilated place in the shade. * Do not directly apply hot air such as from a hair dryer to the headphones. * Do not use cotton buds, etc. to directly wipe water that remains in gaps. ■ About the Remote Controller/Cables Dry immediately after use if they become soiled with perspiration, etc. Wipe with a damp cloth if they are particularly dirty. Using with a dirty cable may cause the cable to deteriorate, resulting in malfunction. English Other functions Auto Power Off function The headphones will automatically turn off after 5 minutes if it has not been connected to a device with the power turned on. Reset function If these headphones stop working or if a malfunction occurs, they can be reset by charging the batteries. * Even if the headphones is reset, volume and other functions won't be initialized. Troubleshooting Power is not supplied Charge the headphones. Unable to pair Pairing is available on version 2.1+EDR or later of the communication system of the Bluetooth device. Bring the headphones and the Bluetooth device closer together – within the range of 1 meter. Set profiles for the Bluetooth device. For procedures on how to set, refer to the operation manual for the Bluetooth device. No sound comes out / a faint sound Turn on the power of the headphones and the Bluetooth device. Turn up the volume of the headphones and the Bluetooth device. Switch the output of the Bluetooth device to the Bluetooth connection. 13 English Troubleshooting Sound is stuttered / noise is caused / sound is interrupted Turn down the volume of the headphones and the Bluetooth device. Keep the microwave and other devices such as wireless LAN away from the headphones. Keep TV, radio and devices with built-in tuners away from the headphones. It can affect these devices. Turn off the equalizer settings of the Bluetooth device. The antenna is installed in the position shown in the figure on the right. Make sure there are no obstructions (such as metallic objects or walls) between the product antenna and the Bluetooth device. Internal Antenna Location Left Cannot hear the person on the other end / voice of the person on the other end sounds too quiet Turn on the power of the headphones and the Bluetooth device. Turn up the volume of the headphones and the Bluetooth device. For the A2DP connection, switch to the HFP/HSP connection. Switch the voice output of the Bluetooth device to the Bluetooth connection. The headphones cannot be charged Securely connect the USB charging cable and charge. Briefly press the Control button when the USB charging cable is connected. The built-in rechargeable battery may have reached the end of its service life if the usage time becomes shorter even though the battery is fully charged or if charging is still not complete after more than 3 hours of continuous charging. In this case, please contact our service center. *For operation of the Bluetooth device, refer to the operation manual for the Bluetooth device, since operation varies with devices. 14 English Specifications Communication System：Bluetooth Version 3.0 Output：Bluetooth Specification Power Class 2 Maximum communication range：Line of sight - approx. 10 m Frequency band：2.402 GHz to 2.480 GHz Modulation method：FHSS Compatible Bluetooth Profiles：A2DP AVRCP HFP HSP Support Codec：SBC Supported content protection method：SCMS-T Headphones Driver：Dynamic 10 mm Transmission band：20 to 20,000 Hz (44.1kHz Sampling） Microphone Element：Electret condenser Directional characteristic：Omnidirectional Sensitivity：-44 dB (1V/Pa at 1 kHz) Effective frequency range：50 to 8,000 Hz Others Power source：DC3.7 V lithium polymer battery Charge terminal：micro USB Operating time : Approx. 4 hours* (Continuous transmission time including music playback time), Max. 60 hours* (Continuous standby time) Charging time : Approx. 3 hours* External dimensions (one side) H28xW32xD27mm (Without cord) Cord Length：Approx. 0.4ｍ Weight：Approx. 23 g(Without Earpieces) Operating temperature：5℃ to 40℃ Accessory：Fine fit earpiece (XS,S,M,L) Active fit earpiece (S,M,L) USB cable for charge (1.0 m), Pouch Optional : Sold separately earpieces Fine fit earpiece *The above figures depend on operating conditions. (For product improvement, this product is subject to modification without notice.) "SOLID BASS" is a registered trademark of Audio-Technica Ltd.. ＊The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Audio-Technica Corporation is under license. All other trademarks are property of their respective owners. 15 Audio-Technica Corp. 2-46-1 Nishi-naruse, Machida-shi, Tokyo 194-8666 2015 Audio-Technica Corp. 132312100
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Create Date : 2015:05:01 14:58:58+10:00 Creator : Adobe Illustrator CS5 Modify Date : 2015:05:01 15:39:22+09:00 XMP Toolkit : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04 Format : application/pdf Title : 新ATH-CKS55XBT EX_Instructions_1 Metadata Date : 2015:05:01 15:39:22+09:00 Creator Tool : Adobe Illustrator CS5 Thumbnail Width : 184 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 8000 bytes, use -b option to extract) Instance ID : uuid:abf188f4-4634-45e8-880f-4e8340565d02 Document ID : xmp.did:1CFD7312C7EFE411BF68CC3801306F2E Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:1BFD7312C7EFE411BF68CC3801306F2E Derived From Document ID : xmp.did:1BFD7312C7EFE411BF68CC3801306F2E Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : proof:pdf History Action : saved, saved, saved, saved History Instance ID : xmp.iid:a8033e24-48b7-449f-828b-d82a1551ef82, xmp.iid:AE2ACB02C2E7E411AE23B4657E20D382, xmp.iid:1BFD7312C7EFE411BF68CC3801306F2E, xmp.iid:1CFD7312C7EFE411BF68CC3801306F2E History When : 2015:04:03 17:21:52+09:00, 2015:04:21 13:59:35+09:00, 2015:05:01 14:58:21+09:00, 2015:05:01 14:58:52+09:00 History Software Agent : Adobe Illustrator CC 2014 (Macintosh), Adobe Illustrator CS5, Adobe Illustrator CS5, Adobe Illustrator CS5 History Changed : /, /, /, / Startup Profile : Print Has Visible Overprint : True Has Visible Transparency : True N Pages : 1 Max Page Size W : 105.000654 Max Page Size H : 148.000785 Max Page Size Unit : Millimeters Font Name : UniversLTStd-Bold, UniversLTStd, UniversLTStd-Light Font Family : Univers LT Std, Univers LT Std, Univers LT Std Font Face : 65 Bold, 55 Roman, 45 Light Font Type : Open Type, Open Type, Open Type Font Version : Version 2.020;PS 002.000;hotconv 1.0.50;makeotf.lib2.0.16970, Version 2.020;PS 002.000;hotconv 1.0.50;makeotf.lib2.0.16970, Version 2.020;PS 002.000;hotconv 1.0.50;makeotf.lib2.0.16970 Font Composite : False, False, False Font File Name : UniversLTStd-Bold_0.otf, UniversLTStd_0.otf, UniversLTStd-Light.otf Plate Names : Black Swatch Groups Group Name : 初期設定のスウォッチグループ Swatch Groups Group Type : 0 Producer : Adobe PDF library 9.90 Page Count : 17EXIF Metadata provided by EXIF.tools