Audio Technica T210AD BODYPACK WIRELESS MICROPHONE TRANSMITTER User Manual

Audio-Technica Corporation BODYPACK WIRELESS MICROPHONE TRANSMITTER Users Manual

Users Manual

2000 SeriesFrequency-agile True Diversity UHF Wireless SystemInstallation and Operation
2000 Series Installation and Operation2This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.This device complies with INDUSTRY CANADA R.S.S. 210, en conformité avec IC: RSS-210/CNR210. Operation is subject to the following conditions: 1) This device may not cause harmful interference and 2) this device must accept any interference received, including interference which may cause undesired operation.CAUTION! Electrical shock can result from removal of the receiver cover. Refer servicing to qualied service personnel. No user-serviceable parts inside. • To prevent re or shock hazard, do not expose this appliance to rain or moisture.• To prevent re, do not place any naked ame sources (such as lighted candles) on the apparatus.• To prevent re, do not cover the ventilation of the apparatus with newspaper, tablecloths, curtains etc.• Do not expose this apparatus to drips or splashes.• Do not place any objects lled with liquids, such as vases, on the apparatus.• Do not install this apparatus in a conned space such as a bookcase or similar unit.• The apparatus should be located close enough to the AC outlet so that you can easily grasp the AC adapter at any time. In case of emergency, disconnect the AC adapter quickly.• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.• Always consider environmental issues and follow your local regulations when disposing of batteries. Do not expose batteries to excessive heat.The circuits inside the receiver and transmitter have been precisely adjusted for optimum performance and compliance with federal regulations. Do not attempt to open the receiver or transmitter. To do so will void the warranty, and may cause improper operation.Notice to individuals with implanted cardiac pacemakers or AICD devices:Any source of RF (radio frequency) energy may interfere with normal functioning of the implanted device. All wireless microphones have low-power transmitters (less than 0.05 watts output) which are unlikely to cause difculty, especially if they are at least a few inches away. However, since a “body-pack” mic transmitter typically is placed against the body, we suggest attaching it at the belt, rather than in a shirt pocket where it may be immediately adjacent to the medical device. Note also that any medical-device disruption will cease when the RF transmitting source is turned off. Please contact your physician or medical-device provider if you have any questions, or experience any problems with the use of this or any other RF equipment.RF Interference Please note that wireless frequencies are shared with other radio services. According to Federal Communications Commission regulations, “Wireless microphone operations are unprotected from interference from other licensed operations in the band. If any interference is received by any Government or non Government operation, the wireless microphone must cease operation...” If you need assistance with operation or frequency selection, please contact your dealer or Audio-Technica. Extensive wireless information also is available at www.audio-technica.com. Thank you for choosing an Audio-Technica professional wireless system. You have joined thousands of other satised customers who have chosen our products because of their quality, performance and reliability. This Audio-Technica wireless microphone system is the successful result of years of design and manufacturing experience.Each 2000 Series wireless system provides a choice of 10 PLL synthesized UHF frequencies in one of ve UHF frequency ranges, available for exible performance in a wide variety of regions worldwide: Frequency Range Band D 656.125 – 678.500 MHz Band E 800.550 – 813.150 MHz Band F 854.900 – 864.900 MHz Band G 722.125 – 744.500 MHz Band I 487.125 – 506.500 MHz The band letter reference at the end of 2000 Series Stock Numbers indicates what band system/component operates in. For simplicity, model numbers used throughout this manual will reference only the basic model number without the band indications. Each wireless system includes a receiver and either a body-pack or handheld transmitter. UniPak® body-pack transmitter systems include accessory microphones for particular applications. All A-T Wireless Essentials® microphones and cables, available separately, are pre-terminated for use with any Audio-Technica 2000 Series wireless system.The ATW-R2100a receiver features true diversity reception. Two antennas feed two completely independent RF sections on the same frequency; automatic logic circuitry continuously compares and selects the superior received signal, providing better sound quality and reducing the possibility of interference and dropouts. The receiver also offers a switchable output attenuator to reduce the level of the output signal by 12 dB for exible use with a variety of system congurations. Switchable antenna power is also provided. Soft-touch controls provide convenient access to selection of operating frequency and automatic scanning, while an LCD information display provides constant monitoring of system operation. The receiver is half-width for a standard 1U 19" rack mount; rack-mount adapters are included. Two receivers can be mounted side by side, using an optional AT8630 joining-plate kit.The versatile ATW-T210a UniPak® body-pack transmitter has both low- and high-impedance inputs plus a bias connection, for use with dynamic and electret condenser microphones, as well as Hi-Z instrument pickups. The UniPak® transmitter also offers separate trim controls for instrument and microphone, plus switchable high/low RF power. The ATW-T220a handheld dynamic microphone/transmitter features the same element used in the PRO 41 dynamic handheld microphone created for professional live-sound venues. It also offers switchable high/low RF power. Both the ATW-T210a UniPak® and ATW-T220a handheld transmitters also offer charging contacts so the units can be placed in an optional recharging station for multi-transmitter charging.For economical operation and wide availability, transmitters in the 2000 Series use two 1.5V AA alkaline batteries or rechargeable two AA NiMH batteries for use with Audio-Technica’s ATW-CHG2 Recharging Station. Both transmitters have battery condition indicators. 2000 Series receivers feature a sophisticated Tone Lock™ tone squelch system that opens the receiver’s audio output only when a 2000 Series transmitter is detected, reducing the possibility of interference. As a result, 2000 Such modifications could void the user's authority to operate the equipment.
2000 Series Installation and Operation 3Series transmitters and receivers must be used together and should not be used with components from other Audio-Technica wireless systems, or with those of other manufacturers.Please note that in multiple-system applications there must be a transmitter-receiver combination set to a separate channel (frequency) for each input desired (only one transmitter for each receiver).Because the wireless frequencies are within UHF TV frequency bands, only certain channels (operating frequencies) may be useable in a particular geographic area. The 10 channels (operating frequencies) per band that are used in the 2000 Series have been selected for multi-channel compatibility. Subject to frequency availability in a particular geographic area, any of these 10 channels may be used together. The operating frequencies that correspond to each of the 10 channels are listed on page 10.Receiver Installation Location For best operation the receiver should be at least 3 ft. (1 m) above the ground and at least 3 ft. away from a wall or metal surface to minimize reections. The transmitter should be at least 3 ft. from the receiver, as shown in Figure A. Keep antennas away from noise sources such as digital equipment, motors, automobiles and neon lights, as well as away from large metal objects.Fig. AOutput ConnectionsThere are two audio outputs on the back panel: balanced and unbalanced. Use shielded audio cable for the connection between the receiver and the mixer. If the input of the mixer is a 1/4" jack, connect a cable from the 1/4" unbalanced audio output on the back of the receiver housing to the mixer. If the input of the mixer is an XLR-type input, connect a cable from the balanced XLR-type audio output on the back panel to the mixer. The two isolated audio outputs permit simultaneous feeds to both unbalanced and balanced inputs. For example, both a guitar amp and a mixer can be driven by the receiver.AntennasAttach the included pair of UHF antennas to the antenna input jacks. The antennas are normally positioned in the shape of a “V” (both 45° from vertical) for best reception.Accessory antennas can be remotely located from the receiver. However, due to signal loss in cables at UHF frequencies, use the lowest-loss RF cables practical for any cable runs over 25 feet. RG8-type is a good choice. Use only copper-shielded cable, not CATV-type foil-shielded wire. Audio-Technica offers quality RF cables in four lengths, as well as remote antennas; see audio-technica.com for a wide selection of wireless system accessories. Antenna Power The antenna input jacks also can provide +12V DC output on their center pins to power inline RF devices. A maximum of 60 mA can be drawn from each of the jacks. While an accidental short-circuit will not harm the internal 12V supply, make certain that an antenna cable shield does not contact the center conductor. Antenna Power is selected by a switch on the back of the ATW-R2100a Receiver. The unit is shipped with the switch in the “off” position. Note: the antennas included with the ATW-R2100a Receiver do not require power. If you have an antenna system that requires power (such as powered antennas or active combiners or splitters) switch the Antenna Power switch to the “on” position. Power Connections Connect the included AC adapter to the DC power input on the back of the receiver. Loop the small cord from the DC plug over the cord hook above the jack, to keep the plug from being detached by an accidental tug on the cord. Operation of the receiver is controlled by the front-panel Power switch.
2000 Series Installation and Operation4Receiver Controls and FunctionsFig. B – Front Panel Controls and Functions 1. POWER SWITCH: Press the Power switch in to turn the receiver on. The LCD window will light, and the operating channel number will be displayed in the window. To turn the receiver off, press the Power switch again. 2. LCD WINDOW: Liquid Crystal Display indicates channel setting and operational readings. See Fig. C for examples.3. UP/DOWN BUTTONS: Press Up or Down arrow buttons to arrive at desired channel. The selected number will ash on and off. Press and hold Set/Scan button to set the channel (operating frequency).4. SET/SCAN BUTTON: Two distinct operations are associated with this button: Touch: A momentary press of the Set/Scan button. Hold: A press and hold (about two seconds) of the Set/Scan button. The Set/Scan button can be used in two ways: Manual Set Mode, to permit selection of an operating channel; and Automatic Scan/Set Mode, to initiate the automatic channel scan and selection, as follows: Manual Set Mode: After using the Up or Down arrow button to arrive at desired channel, hold the Set/Scan button to set the channel. NOTE: Before the channel has been set, a touch of the Set/Scan button will revert the channel to its previous setting. Automatic Scan/Set Mode: Hold the Set/Scan button. The Automatic Scan/Set Mode will automatically scan for and set the next open channel.5. MOUNTING ADAPTERS: For mounting the receiver in any standard 19" rack. Attach adapters to the receiver with the screws supplied and remove the four receiver feet. (Use optional AT8630 joining- plate kit to mount two ATW-R2100 receivers side-by-side.)Fig. C – Receiver LCD Window Display6. RF SIGNAL LEVEL INDICATOR: Shows the strength of the RF signal received from the transmitter.7. TUNER OPERATION INDICATOR: Indicates which Tuner (A or B) has the better reception and is in operation.8. CHANNEL DISPLAY: Shows which channel is selected.9. AF LEVEL INDICATOR: Shows the audio modulation level of the received signal.1 2 3 4 56 7 98
2000 Series Installation and Operation 5Fig. D – Rear Panel Controls and Functions 10. ANTENNA INPUT JACK: BNC-type antenna connector for Tuner “B.” Attach the antenna directly, or extend it with a low-loss antenna cable. See the “Antennas” section on page 3 for more details.11. ANTENNA POWER SWITCH: Two-position switch turns on/off the 12V AC antenna power for use with powered antennas or accessories. Factory setting is off. See the “Antennas” section on page 3 for more details.12. SQUELCH CONTROL: Adjusts level of noise-muting circuit (preset at factory but can be adjusted as circumstances warrant). Factory setting is full counterclockwise (minimum).13. ANTENNA INPUT JACK: Input for Tuner “A.” Attach the supplied antenna directly, or extend it to an accessory antenna with a low- loss antenna cable.14. AF OUTPUT ATTENUATOR: Two-position switch adjusts audio output level of the balanced (XLR) audio output jack with attenuation of 0 dB or –12 dB. Factory setting is 0 dB.15. AF LEVEL CONTROL: Adjusts audio output level of both AF output jacks. Factory setting maximum output—fully clockwise.16. GROUND LIFT SWITCH: Disconnects the ground pin of the balanced output jack (15) from ground. Normally, the switch should be to the left (ground connected). If hum caused by a ground loop occurs, slide switch to the right (ground lifted). Factory setting is ground connected. 17. BALANCED AUDIO OUTPUT JACK: XLRM-type connector. A standard 2-conductor shielded cable can be used to connect the receiver output to a balanced microphone-level input on a mixer or integrated amplier.18. UNBALANCED AUDIO OUTPUT JACK: 1/4" phone jack. Can be connected to an unbalanced aux-level input of a mixer, guitar amp or tape recorder.19. POWER INPUT JACK: Connect the DC plug from the included in-line AC adapter.20. CORD HOOK: Loop the small DC cord around the cord hook to keep the DC plug from pulling out accidentally.10 11 13 1412 1716 18 1915 20
2000 Series Installation and Operation6Transmitter Controls and FunctionsBattery SelectionTwo 1.5V AA alkaline batteries or rechargeable AA NiMH batteries for use with Audio-Technica’s ATW-CHG2 Recharging Station are recommended. UniPak® Transmitter Battery Installation1. Open the transmitter door by pressing gently on the side-cover indentations and pulling back the hinged cover.2. Lift the battery-keeper arm, and carefully insert two fresh 1.5V AA alkaline batteries or rechargeable AA NiMH batteries, observing correct polarity as marked inside the battery compartment.3. Close the battery-keeper arm.4. Close the transmitter door.Fig. E – UniPak® Transmitter OpenHandheld Transmitter Battery Installation1. While holding the upper part of the transmitter body below the ball- screen, unscrew the lower body cover, slide it downward, and remove it to expose the battery compartment.2. Observe correct polarity as marked inside the battery compartment and carefully insert two fresh 1.5V AA alkaline batteries or rechargeable AA NiMH batteries. Make certain the batteries are fully seated in the battery compartment. (Fig. F )3. Slide the lower body cover back up the body, then screw the housing together. Do not overtighten. Note: Remove batteries from the handheld transmitter starting at the bottom end, where nger indents in the battery housing are provided for easy grip.Fig. F – Handheld Transmitter Battery CompartmentBattery Indicator After the battery is installed, turn on the power switch (located on the bottom of the handheld transmitter and on the top of the UniPak transmitter). The battery indicator LED (Fig. G/H) should turn red. If it does not, the batteries are installed incorrectly or they are dead.Fig. G – UniPak Transmitter Top View UniPak®Transmitter Input Connection Connect an audio input device (microphone or guitar cable) to the audio input connector on the top of the transmitter. A number of Audio-Technica professional microphones and cables are available separately, pre-terminated with a UniPak input connector.UniPak® Transmitter AntennaThe ATW-T210a UHF UniPak® body-pack transmitter includes one eld-replaceable antenna mounted on the transmitter. The antenna simply screws into the transmitter’s antenna tting. Check the installed antenna occasionally to make certain it is snugly attached (only nger-tight). If the received signal is marginal, experiment with different transmitter positions on your body or instrument or try repositioning the receiver. Do not attempt to modify the transmitting antenna. Replace it only with the same parts, available from the Audio-Technica Service Department.Charging ContactsTransmitter DoorAntennaAudio Input JackInstrument/Microphone Level Trim ControlsChannel Selector SwitchRF Power Select SwitchService Port (for factory use only)Battery-keeper Arm with Screwdriver attachedPower-on LEDScrewdriverInput ConnectorPower SwitchBattery IndicatorAntennaPower SwitchBattery IndicatorFig. H – Handheld Transmitter Bottom View
2000 Series Installation and Operation 7System OperationSwitch on the receiver. Do not switch on the transmitter yet.Receiver On…The LCD display will light up and one of the tuner operation indicator LCD segments (A or B) will light, even though the transmitter is not on. If two or more of the RF LCD segments light up at this point, there may be RF interference in the area. If this occurs, change operating channels (select another frequency).How to Make Operating Channel ChangesOperating channel changes (frequency changes) may be made in two ways: manually and automatically. To change channel manually 1. Use the Up/Down arrow buttons to reach the desired channel number.2. Hold the Set/Scan button until the channel number stops ashing to set the receiver to the channel indicated. NOTE: Before the channel has been set, a touch (momentary press) of the Set/Scan (rather than a hold) will revert the channel to its previous setting.To change channel automatically1. Hold the Set/Scan button. The Automatic Scan/Set Mode will automatically scan for and set the next open channel. LCD screen will ash “FS” four times to indicate start of scan.Transmitter On…Before turning on the transmitter, use the provided screwdriver to set the transmitter channel selector switches (Fig. E/I) to the same numbers as those displayed on the receiver. Always turn the transmitter off when changing channels (frequencies).The transmitters have a two-position, on-off power switch. When the switch is “On,” the transmitter produces both RF and audio.The transmitters have a two-position RF power select switch, offering low/high transmission modes to conserve battery life/maximize power. Factory setting is high. There is about a half-second delay after the transmitter is switched to the “On” position before the receiver’s Tone Lock squelch un-mutes the receiver.When the transmitter is switched on and in normal operation, the receiver’s RF signal level indicators will display as dark segments (signal strength indicators) from bottom to top at the left side of the LCD display.Setting LevelsCorrect adjustment of transmitter audio input, receiver audio output, and mixer/amplier input and output levels is important for optimum system performance.ATW-T220a Handheld TransmitterThe 2000 Series handheld transmitter has factory pre-set audio input levels. Factory setting is full clockwise, maximum gain. 1. While speaking/singing into the microphone at typically loud levels, check the AF meter levels on the receiver. If all ve AF meter bars are consistently illuminated and distortion is heard through the system, it may be necessary to adjust the transmitter audio input level.2. To adjust the transmitter audio input level, unscrew the lower body cover and slide it downwards, exposing the screwdriver and level trim control (Fig. I ). Remove the screwdriver and gently turn the level trim control counterclockwise until the topmost receiver AF level meter bar is illuminated only on audio peaks. 3. Return the screwdriver to its clip and close and secure the lower body. No further transmitter gain adjustments should be needed, as long as the acoustic input does not change signicantly.CAUTION! The small trimmer controls are delicate; use only the supplied screwdriver. Do not force the trimmers beyond their normal 180° range of rotation. Return the screwdriver to its storage clip when not in use.Fig. I – Handheld Transmitter Interior ViewCharging ContactsRF Power Select SwitchService Port (for factory use only)Channel Selector SwitchLevel Trim ControlScrewdriver
2000 Series Installation and Operation8Setting Levels (Continued)ATW-T210a UniPak® TransmitterTrimmer adjustments in the UniPak® transmitter (Fig. E) will enable you to use microphones or instruments with different output levels.1. For MIC: Set microphone level trim control fully clockwise (maximum) and instrument level trim control fully counterclockwise (minimum). Factory setting is fully clockwise (maximum). For INSTRUMENT: Set instrument level trim control fully clockwise (maximum) and microphone level trim control fully counterclockwise (minimum). Factory setting is fully clockwise (maximum).2. Set the receiver’s AF Level control to its full clockwise position (maximum). See Figure D on page 5.3. Plug the mic or instrument into the transmitter and power up the system.4. For MIC: Make an initial adjustment of the mixer’s level controls that will allow audio through the system. For INSTRUMENT: Make an initial adjustment of the instrument amplier input level control that will allow audio through the system.5. For MIC: While speaking/singing into the microphone at typically loud levels, check the AF meter levels on the receiver. If all ve meter bars are consistently illuminated and distortion is heard through the system, it may be necessary to adjust the UniPak transmitter audio input level. To adjust the transmitter audio input level, gently turn the microphone level trim control counterclockwise until the topmost receiver AF level meter bar is illuminated only on audio peaks. For INSTRUMENT: While playing the instrument at typically loud levels, check the AF meter levels on the receiver. If all ve meter bars are consistently illuminated and distortion is heard through the system, it may be necessary to adjust the UniPak transmitter audio input level. To adjust the transmitter audio input level, gently turn the instrument level trim control counterclockwise until the topmost receiver AF level meter bar is illuminated only on audio peaks.6. For MIC: While again speaking/singing into the microphone at typically loud levels, adjust the mixer’s input trim control so the highest sound pressure level going into the microphone causes no input overload in the mixer, and yet permits the mixer’s channel and output level controls to operate in their “normal” range (not set too high or too low). For INSTRUMENT: While again playing the instrument at typically loud levels, adjust the receiver’s AF Level control so the highest signal level causes no input overload in the instrument amplier and yet permits the amplier’s input level controls to operate in their “normal” range (not set too high or too low). Note: If the mixer cannot be adjusted to operate in its normal range without distortion, adjust the receiver’s AF Level Control (turn counterclockwise) until the mixer/ amplier is no longer overloaded.Fig. E – UniPak® Transmitter OpenReceiver SquelchThe squelch control on the back panel of the receiver is preset at the factory for best system performance (factory setting is full counterclockwise), but can be adjusted if you must use the system in an area with considerable RF interference. If there is interference in the audio, and changing the channel is not an option, adjust the squelch control so the system will receive the signal from your transmitter but will “squelch” or eliminate the unwanted background RF noise. This adjustment can cause a reduction in useable range of the wireless transmitter, so set the control to the lowest position that reliably mutes the unwanted RF signals.Transmitter DoorAntennaAudio Input JackInstrument/Microphone Level Trim ControlsChannel Selector SwitchRF Power Select SwitchService Port (for factory use only)Battery-keeper Arm with Screwdriver attachedPower-on LED
2000 Series Installation and Operation 9Specications†Overall SystemUHF Operating Frequencies Frequency Range Number of Channels Band D: 656.125 to 678.500 MHz 10 Band E: 800.550 to 813.150 MHz 10 Band F: 854.900 to 864.900 MHz 10 Band G: 722.125 to 744.500 MHz 10 Band I : 487.125 to 506.500 MHz 10 Not all frequencies are available in all areas. Please check with local regulations.Modulation Mode FM Maximum Deviation ±40 kHz Dynamic Range > 110 dB (A-weighted), typical Total Harmonic Distortion < 1% (at 1 kHz, ±20 kHz deviation) Operating Range 100 m (300'), typical Open range environment with no interfering signals. Operating Temperature Range 5º C to +45º C 41º F to 113º F Battery and LCD performance may be reduced at very low temperatures. Frequency Response 100 Hz to 15 kHz (+1 dB, -3 dB) ATW-R2100a ReceiverReceiving System True diversityImage Rejection 60 dB nominal, 55 dB minimumRF Sensitivity 20 dBuV at 60 dB S/N ratio (50 ohms termination) Maximum Output Level XLR, balanced: +9 dBV ¼" (6.3 mm), unbalanced: +4 dBVBalanced Audio Output Attenuator Two position switch: 0 / -12 dBAntenna Input BNC-type, 50 ohms Bias voltage 12V DC, 60 mA, each Power Requirements 12-18V DC, 500 mA Dimensions 210.0 mm (8.27") W x 162.2 mm (6.39") D x 44.0 mm (1.73") H Not including BNC connectors or feet. Net Weight 1.0 kg (35.3 oz), without accessories Accessories Included Two exible UHF antennas; AC adapter (country dependent); rack-mount adapters ATW-T210a UniPak® TransmitterRF Power Output (50 ohms) High: 30 mW, Low: 10 mW (switchable)Spurious Emissions Following federal and national regulations Input Connection Four-pin Locking Connector Pin 1: GND, Pin 2: INST INPUT, Pin 3: MIC INPUT, Pin 4: DC BIAS +9V Batteries Two 1.5V AA, not includedBattery Life High: 7 hours (alkaline) Low: 9 hours (alkaline) Depending on battery type and use pattern. Dimensions 66.0 mm (2.60") W x 22.5 mm (0.89") D x 92.3 mm (3.63") H Net Weight 81 g (2.9 oz), without batteries ATW-T220a Handheld TransmittersRF Power Output (50 ohms) High: 30 mW; Low: 10 mW, (switchable)Spurious Emissions Following federal and national regulations Microphone Element Dynamic cardioid Batteries Two 1.5V AA, not included Battery Life High: 7 hours (alkaline) Low: 9 hours (alkaline) Depending on battery type and use pattern. Dimensions 232.0 mm (9.13") long, 48.0 mm (1.89") diameter Net Weight 252 g (8.9 oz), without batteriesAccessory Included AT8456a Quiet-Flex™ stand clamp † In the interest of standards development, A.T.U.S. offers full details on its test methods to other industry professionals on request.Specications are subject to change without notice.
2000 Series Installation and Operation102000 Series Frequency Channel PlanBand D Channel Frequency-MHz1 656 . 125 2 659 . 375 3 660 . 0004 662 . 125 5 665 . 1256 669 . 750 7 671 . 5008 677 . 000 9 678 . 125 10 678 . 500 Band E Channel Frequency-MHz1 800 . 225 2 802 . 775 3 804 . 000 4 804 . 700 5 805 . 9006 806 . 300 7 813 . 100 8 813 . 9009 815 . 000 10 818 . 025 Band F Channel Frequency-MHz1 863 . 1002 863 . 500 3 864 . 100 4 864 . 900 5 854 . 900 6 855 . 2757 855 . 900 8 856 . 1759 858 . 200 10 861 . 750 Band G Channel Frequency-MHz1 772 . 125 2 725 . 3753 726 . 000 4 728 . 125 5 731 . 1256 735 . 750 7 737 . 5008 743 . 000 9 744 . 125 10 744 . 500Band IChannel Frequency-MHz1 487 . 125 2 487 . 625 3 488 . 875 4 491 . 7505 494 . 375 6 495 . 375 7 501 . 3758 503 . 375 9 505 . 750 10 506 . 500CAUTION: U.S. Public Safety/Security Restrictions (Private Land Mobile Radio Services)Pertains to Band I Only.Avoid the frequencies/channels listed below in each of the following U.S. metropolitan areas (as of November 2009). Refer to www.fcc.gov for updates.Land Mobile AllocationMetropolitan Areas 2000 Series I Band ChannelsTV Channels* to Avoid in Indicated Metropolitan AreasBoston, MA 1, 2 14, 16Dallas, TX 1, 2 16Detroit, MI 1, 2 15, 16Houston, TX 3, 4 17Los Angeles, CA 1, 2, 10 14, 16, 20New York, NY 1, 2 14, 15, 16Philadelphia, PA 7, 8, 9, 10 19, 20Pittsburgh, PA 5, 6 14, 18San Francisco, CA 1, 2, 3, 4 16, 17Washington, DC 3, 4, 5, 6 17, 18Note: Cleveland and Chicago public safety allocations (TV Channels 14 & 15) and Miami FL public safety allocations (TV Channel 14) are outside of the 2000 Series operating bandwidth.* The 2000 Series operates in TV channels 16-20; Channels 14 and 15 are outside the 2000 Series operating bandwidth.U.S. Two-Year Limited WarrantyThis product and selected Audio-Technica brand products purchased in the U.S.A. from an authorized Audio-Technica (A.T.U.S.) dealer are warranted for two years from date of purchase by A.T.U.S. to be free of defects in materials and workmanship. To identify those products, go to www.audio-technica.com/usawarranties. In event of a defect, End-User’s exclusive remedy is at A.T.U.S.’ election, the cost of repair, refund of the purchase price in the form of credit or cash, or replacement of the product. The product must be delivered to A.T.U.S. or an Authorized Service Center, prepaid, together with the sales slip or other proof of purchase date. This warranty excludes defects due to normal wear, abuse, shipping damage, or failure to use product in accordance with instructions. This warranty is void in the event of unauthorized repair or modication, or removal or defacing of the product labeling.For U.S. service return instructions and procedure please go to: www.audio-technica.com/returninstructions.A.T.U.S.’ warranty is to the End User only. Except for A.T.U.S.’ said express warranty, A.T.U.S. MAKES NO WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE PRODUCTS. A.T.U.S. SPECIFICALLY MAKES NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.Except to the extent precluded by applicable state law, A.T.U.S. IS NOT LIABLE FOR CONSEQUENTIAL, INCIDENTAL, DIRECT OR SPECIAL DAMAGES ARISING, DIRECTLY OR INDIRECTLY, IN RESPECT OF SUCH PRODUCTS OR USE OR FAILURE THEREOF, WHETHER BASED ON BREACH OF WARRANTY, NEGLIGENCE, STRICT LIABILITY, TORT OR OTHERWISE.This warranty gives you specic legal rights, and you may have other rights which vary from state to state.Outside the U.S.A., please contact your local dealer for warranty details.Audio-Technica U.S., Inc.1221 Commerce DriveStow, Ohio 44224
11Stetement of Compliance
Audio-Technica U.S., Inc.1221 Commerce Drive, Stow, Ohio 44224 USA +1 (330) 686-2600Audio-Technica LimitedOld Lane, Leeds LS11 8AG England +44 (0) 113 277 1441Audio-Technica (Greater China) LimitedUnit K, 9/F., Kaiser Est. (Ph.2) 51 Man Yue St. Kowloon, HK. +852-2356-9268Audio-Technica (S.E.A.) Pte. Ltd.No 1 Ubi View, #01-14 Focus One, Singapore 408555 +65-6749-5686Audio-Technica Corporation2206, Naruse Machida, Tokyo Japan ©2010 Audio-Technica U.S., Inc. audio-technica.com P# 2323-04360 P52121 Printed in MalaysiaTo reduce the environmental impact of a multi-language printed document, product information is available online at www.audio-technica.com in a selection of languages.An de réduire l’impact sur l’environnement de l’impression de plusieurs, les informations concernant les produits sont disponibles sur le site www.audio-technica.com dans une large sélection de langue.Para reducir el impacto al medioambiente, y reducir la producción de documentos en varios leguajes, información de nuestros productos están disponibles en nuestra página del Internet: www.audio-technica.com.Para reduzir o impacto ecológico de um documento impresso de várias linguas, a Audio-Technica providência as informações dos seus produtos em diversas linguas na www.audio-technica.com.Per evitare l’impatto ambientale che la stampa di questo documento determinerebbe, le informazioni sui prodotti sono disponibili online in diverse lingue sul sito www.audio-technica.com.Der Umwelt zuliebe nden Sie die Produktinformationen in deutscher Sprache und weiteren Sprachen auf unserer Homepage: www.audio-technica.com.Om de gevolgen van een gedrukte meertalige handleiding op het milieu te verkleinen, is productinformatie in verschillende talen “on-line” beschikbaar op: www.audio-technica.com.

Navigation menu