Audio Technica T220D Handheld Wireless Microphone User Manual USERS MANUAL
Audio-Technica Corporation Handheld Wireless Microphone USERS MANUAL
USERS MANUAL
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 489087 |
| Application ID | cynPlkj5u/srP0yIWlFSTQ== |
| Document Description | USERS MANUAL |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 57.85kB (723069 bits) |
| Date Submitted | 2004-11-17 00:00:00 |
| Date Available | 2004-11-15 00:00:00 |
| Creation Date | 2004-10-29 10:38:36 |
| Producing Software | Adobe Acrobat 6.0.2 Paper Capture |
| Document Lastmod | 2004-10-29 10:50:11 |
| Document Title | USERS MANUAL |
| Document Creator | HP PrecisionScan Pro 3.0 |
2000 Series Professional
UHF Wireless Systems
ATW-2110 UniPak’” Transmitter System
ATW-2120 Handheld Dynamic Microphone System
Installation and Operation
Qaudio-technicaw
Professional UHF Wireless Systems
Installation and Operation
This device complies with part 15 of the FCC Rules.
Operation is subject to the condition that this device does
not cause harmful interference.
This device complies with INDUSTRY CANADA FLSS. 210,
en conformite avec IC: RSS-ZlO/CNRZiO. Operation
is subject to the following conditions: 1) This device may
not cause harmful Interference and 2) this devrce must
accept any interference received, including interference
which may cause undesired operation.
CAUTION! Electrical shock can result from removal of the
receiver cover. Refer servicing to qualified service personnel.
N0 user»serviceable parts inside. Do not expose to rain or
moisture.
The circuits inside the receiver and transmitter have been
precisely adjusted for optimum performance and compli-
ance with federal regulations. Do not attempt to open the
receiver or transmitter. To do so will void the warranty,
and may cause improper operation.
Notice to individuals ua'tthnlanxeiaazdimnmmakezs
attenuates.
Any source of RF (radio frequency) energy may interfere with
normal functioning of the implanted device. All wireless
microphones have Iowpower transmitters (less than 005
watts output) which are unlikely to cause difficulty, especial-
ly if they are at least a few inches away. However, since a
"body—pack" mil: transmitter typically is placed against the
body, we suggest attaching it at the belt, rather than in a shirt
pocket where it may be immediately adjacent to the medical
device. Note also that any medical-device disruption will
cease when the RF transmitting source is turned off. Please
contact your physician or medical-device provider if you have
any questions, or experience any problems with the use of
this or any other HF equipment.
Introduct on
Thank you for choosing an Audio-Technica professional wireless
system. You have joined thousands of other satisfied customers
who have chosen our products because of their quality,
performance and reliability. This Audio-Technica wireless
microphone system is the successful result of years of design
and manufacturing experience,
Each 2000 Series Wireless system provides a choice of 10 PLL<
synthesized UHF frequencies in the 656-678 MHz band (TV
channels 45—48). Each wireless system includes a receiver
and either a body»pack or handheld transmitter. Individual
components are also available separately.
The ATW-RZiOO receiver features true diversity reception Two
antennas feed two completely independent RF sections on
the same frequency; automatic logic circuitry continuously
compares and selects the superior received signal, providing
better sound quality and reducing the possibility of interference
and dropouts. Soft-touch controls provide convenient access
to selection of operating frequency and automatic scanning,
while an LCD information display provides constant mOHJlOTng
of system operation, The receiver is halfvwidth for a standard
1U 19' rack mount; rack~mount adapters are included. Two
receivers can be mounted side by side, usrng an optional
AT8630 ioiningplate kit.
The versatile ATWJzio UniPakTM body—pack transmitter has
both Icw— and highaimpedance inputs plus a bias connection,
for use with dynamic and electret condenser microphones,
as well as Hi-Z instrument pickups.
The ATWVT220 handheld dynamic microphone/transmitter
features the same element used in the PRO 41 dynamic
handheld microphone created for professional live-sound
venues.
Transmitters in the 2000 Series use two 1.5V AA batteries for
economical operation and wide availability. Both transmitters
have battery condition indicators.
2000 Series receivers feature a sophisticated Tone Lock‘M
tone squelch system that opens the receiver’s audio output
only when a 2000 Series transmitter is detected, reducing the
possibility of interference. As a result, 2000 Series transmitters
and receivers must be used together and should not be used
with components from other Audro-Technica wireless systems,
or With those of other manufacturers.
Please note that in multiple-system applications there must be
a transmitterreceiver combination set to a separate channel
(frequency) for each input desired (only one transmitter for
each receiver).
Because the Wireless frequencies are within UHl= TV frequency
bands, only certain channels (operating frequencies) may he
useable in a particular geographic area, The 10 channels
(operating frequencies) that are used in the 2000 Series have
been selected for multl—channel compatibility. Subject to
frequency availability in a particular geographic area, any of
these 10 channels may be used together.
The operating frequencies that correspond to each of the 10
channels are listed on page ii.
Rece' er Installation
Location
For best operation the receiver should be at least 3 ft. (1 m)
above the ground and at least 3 ft. away from a wall or metal
surface to minimize reflections. The transmitter should be at
least 3 ft. from the receiver, as shown in Figure A, Keep
antennas away from noise sources such as digital equipment,
motors, automobiles and neon lights, as well as away from
large metal objects.
Output. Connections
There are two audio outputs on the back panel: balanced
(12.5 my) and unbalanced (25 mVi, Use shielded audio cable
for the connection between the receiver and the mixer. if the
input of the mixer is a V.“ jack, connect a cable lrorn the ‘l.’
unbalanced audio output on the back at the receiver housing
to the mixer. If the input of the mixer is an XLR-type input,
connect a cable from the balanced XLR»type audio output on
the back panel to the mixer. The two isolated audio outputs
permit simultaneous feeds to both unbalanced and balanced
inputs. For example, both a guitar amp and a mixer can be
driven by the receiver.
Figure A
Antennas
Attach the included pair of UHF antennas to the antenna input
lacks. The antennas are normally positioned in the shape of a
"V” (both 45“ from vertical) for best reception.
Accessory antennas can be remotely located from the receiver.
However, due to Signal loss in cables at UHF frequencies, use
the lowest-loss HF cables practical for any cable runs over 25
feet RGB-type is a good choice. Use only copper-shielded
cable, not CATV-type roil»shielded wire. Audio»Technica offers
quality RF cables in four lengths, as well as remote antennas;
see the Optional System Accessories section on page 10.
Power Connections
Connect the included AC adapter to the DC power input on the
back of the receiver. Loop the small cord from the DC plug over
the cord hook above the jack, to keep the plug from being
detached by an accidental tug on the cord. Then plug the
adapter into a standard 120 Volt 60 Hz AC power outlet
Operation of the receiver is controlled by the front—panel Power
switch.
(Note: Units supplied to countries with 230V mains should
include an inaline AC adapter appropriate for that countw.
Use the included adapter only with 120V 60 Hz AC
power sources.)
Rec
Figure B-Front Panel Controls and Functions
@ i 2583 »& mm
or, m fig}
1. POWER SWITCH: Press the Power swuch in to turn the
receiver on The LCD Window will light, and the operating
channel number will be displayed in the window. To turn
the receiver off, press the Power switch again.
2. LCD WINDOW: Liquid Crystal Display indicates Channel
setting and operational readings. See Fig. C for examples.
3. UP/DOWN BUTTONS: Press Up or Down arrow buttons to
arrive at desired channel. The selected number will flash on
and 0". Press and hold Set/Scan button to set the channel
(operating frequencylr
4. SET/SCAN BUTTON: Two distinct operations are associated
with this button:
Touch:A momentary press of the Set/Scan button.
Hold: A press and hold (about two seconds) of the
Set/Scan button.
The Set/Scan button can be used in two ways: Manual Set
Mode, to permit selection of an operating channel; and
Automatic Scan/Set Mode, to initiate the automatic channel
scan and selection, as follovrs:
Manual Set Mode: After using the Up or Down arrow
button to arrive at desired channel, hold the Set/Scan
bUtton to set the channel, NOTE: Before the channel has
been set, a touch of the Set/Scan button will revert the
channel to its previous setting.
Automatic Scan/Sat Mode: Hold the Set/Scan button. The
Automatic Scan/Set Mode will automatically scan for and
set the next open channel.
5. MOUNTING ADAPTERS: For mounting the receiver in any
standard 19' rack. Attach adapters to the receiver with the
screws supplied and remove the tour receiver feet. (Use
optional AT8630 joining—plate kit to mount two ATW~H2100
receivers side-hy-side.)
Figure C-Receiver LCD Window Display
6. HF SIGNAL LEVEL INDICATOR: Shows the strength of the
RF signal received from the transmitterr
7. TUNER OPERATION INDICATOR: indicates which Tuner
(A or Bl has the better reception and is in operation.
8. CHANNEL DISPLAY: Shows which channel rs selected.
9. AF LEVEL INDICATOR: Shows the audio modulatldn level
of the received signal.
10.
11
12.
13.
14.
Figure D-Rear Panel Controls and Functions
Receiver Controls and Functions {Cant
Edi
ANTENNA INPUT JACK: ENC-type antenna connector for
Tuner “.”8 Attach the antenna directly, or extend it with a
lawless antenna cable. See the "Antennas” section on
page 3 for more details.
SOUELCH CONTROL: Adjusts level of noisemutlng circuit
(preset at factory but can be adjusted as circumstances
warrant). Factory setting is full counterclockwise
ANTENNA INPUT JACK: Input for Tuner ”A.“ Attach the
supplied antenna directly, or extend it to an accessory
antenna with a low-loss antenna cable.
AF LEVEL CONTROL: Adjusts audio output level of both AF
output lacks; maximum output is fully clockwise.
GROUND LIFT SWITCH: Disconnects the ground pin of the
balanced output jack (15) from ground. Normally, the switch
should be to the left (ground connected). [I hum caused by
Iaffuound loop occurs, slide switch to the right (ground
i ed).
15. BALANCED AUDIO OUTPUT JACK: XLRM—type connector.
A standard 2-conductor shielded cable can be used to
connect the receiver output to a balanced microphone-level
input on a mixer or integrated amplifier.
16. UNBALANCED AUDIO OUTPUT JACK: '/4' phone jack Can
be connected to an unbalanced aux-level input of a mixer,
guitar amp or tape recorder,
17. POWER INPUT JACK’ Connect the DC plug from the
included in-Irne AC adapter.
18. CORD HOOK: Loop the small DC cord around the cord
hook to keep the DC plug from pulling out accidentally.
Tran
Battery Selection
Two 1.5V AA alkaline batteries are recommended,
Uni’Pak’M Transmitter Battery installation
1. Open the transmitter door by pressing gently on the
side—cover indentations and pulling back the hinged cover
shown in Fig. E below.
2. Lift the battery-keeper arm, and carefully insert two lresh
1.5V AA alkaline batteries, observing correct polarity as
marked inside the battery compartment,
3, Close the battery-keeper arm.
4, Close the transmitter door,
Figure E-UniPak Transmitter Open
Antenna
Powumn IED
fie: Audln Input Jack
u— w lnstrumtntM‘icmphone
Level Trim Controls
Channel , *
Selector '
Swltch Q
Battery-keeper
Arm to an]:
ScrewA mm on
opposite side Transmitter
Door
irter Controls And Functions
Handheld Transmitter Battery Installation
l. While holding the upper part of the transmitter body by the
translucent ring below the ball‘screen, unscrew the lower
body cover, slide it downward, and remove it to expose the
battery compartment.
2 Observe correct polarity as marked inside the battery
compartment and carefully insert two fresh 1.5v AA
alkaline batteries. Insert the first battery and slide it down
Then insert the second battery into the space remaining
Make cenain the batteries are fully seated in the battery
compartment. (Fig. F)
3. Slide the lower body cover back up the body, then screw
the housing together. Do not overtighten
Note: Remove batteries from the handheld transmitter starting
at the bottom end, where finger indents in the battery housing
are provided for easy grip.
Figure F-Handhald Transmitter Battery Compartment
Screwdriver
Battery Indicator
After the battery is installed, turn on the power switch (located
on the bottom of the handheld transmitter and on the top of the
Uanak transmitter), The battery indicator LED (Fig G/Hi should
turn red. If it does not, the batteries are installed incorrectly or
they are dead.
Figure G-UniPak
Transmitter Top View
Figure H-Hanrlheld
Yransmitter Bottom
View
Battery Indicator 5mm, indicator
Antenna
InputOonnlctor
Pow-r Switch Pow-r Switch
UniPak Transmitter Input Connection
Connect an audio input device (microphone or guitar cable) to
the audio input connector on the top of the transmitter. A
number of Audio»Technica professional microphones and cables
are available separately, pre-term‘inated with a UniPak input
connector (see "Optional System Accessories" on page 10],
UniPak Transmitter Antenna
The ATWvTZiO UHF transmitter includes one field-replaceable
antenna mounted on the transmitter The antenna simply
screws into the transmitter's antenna fitting. Check the installed
antenna occasionally to make certain it is snugly attached lonly
linger-tight). If the received signal is marginal, experiment with
different transmitter positions on your body or instrument or try
repositioning the receiver. Do not attempt to modify the
transmitting antenna, Replace it only with the same par-rs,
available from the Audio-Technica Servrce Department,
System Opera on
Switch on the receiver. Do notswnch on the transmitter yet,
Receiver On“.
The LCD display will light up and one ol the tuner operation
indicator LCD segments (A or B) will light, even though the
transmitter is not on, If two or more of the RF LCD segments
light up at this point, there may be RF interference in the area.
If this occurs, change operating channels (select another
frequenc'yl.
How to Make Operating Channel changes
Operating channel changes (frequency changes) may be made
in M0 ways: manually and automatically.
To change channel manually
1. Use the Up/Down arrow buttons to reach the desired
channel number.
2 Hold the Set/Scan button until the channel number stops
flashing to set the receiver to the channel indicated.
NOTE: Before the channel has been set, a touch
(momentary press) of the Set/Scan (rather than a holdi will
revert the channel to its previous setting.
To change channel automatically
1. Hold the Set/Scan button. The Automatic Scan/Set Mode
will automatically scan tor and set the next open channel.
LCD screen will flash “FS” four times to indicate start of
scan.
Transmltter On“.
Beiora turning on the transmitter, use the provided screwdriver
to set the transmitter channel selector switches (Fig. EA) to the
same numbers as those displayed on the receiver. Always turn
the transmitter oif when changing channels (frequenciesll _
The transmitters have a twoposition, on—oli power switch.
When the switch is “On," the transmitter produces both RF
and audio.
There is about a half-second delay after the transmitter is
switched to the "On" position before the receiver's Tone Lock
squelch un-rnutes the receiver.
When the transmitter is switched on and in normal operation,
the receiver's RF signal level indicators will display as dark
segments (signal strength indicatorsi from bottom to top at the
left side of the LCD display.
Setting Levels
Correct adjustment of transmitter audio input, receiver audio
output, and mixer/amplifier input arid output levels is important
for optimum system performance.
ATW-T220 Handheld Transmittal
The 2000 Series—handheld transmitter has factory ore-set audio
input levels. Factory setting is full clockwise, maximum gainl
While speaking/singing into the microphone at typically loud
levels, check the AF meter levels on the receiver. It all five AF
meter bars are consistently illuminated and distortion is heard
through the system, it may be necessary to adjust the
transmitter audio input level,
To adjust the transmitter audio input level, unscrew the lower
body cover and slide it downwards. exposing the screwdriver
and level trim control (Fig I). Remove the screwdriver and gently
turn the level trim control counterclockwise until the topmost
receiver AF level meter bar is illuminated only on audio peaks.
Return the screwdriver to its clip and close and secure the lower
body. No further transmitter gain adjustments should
be needed, as long as the acoustic input does not change
significantly,
CAUTION! The small trimmer controls are delicate, use only '
the supplied screwdriver, Do not force the trimmers beyond
their normal 180“ range of rotation
Return the screwdriver to its storage C|Ip when not in use,
Figure I-Handheld Transmitter Interior View
Level Trim Control
Channel
salami
Switch
Screwdriver
Set 9 Levels (Continued)
ATMl-T210 Unr'PakW Transmitter
Trimmer adjustments in the UniPak‘M transmitter (Fig. E) will
enable you to use microphones or instruments with different
output levels.
1. For MIC: Set microphone level trim control fully
clockwise (maximum) and instrument level trim control
fully counterclockwise (minimum).
For INSTRUMENT: Set instrument level trim control fully
clockwise (maximum) and microphone level trim control
fully counterclockWise (minimum).
2, Set the receiver‘s AF Level control to its full clockwise
positron (maximum). See Figure D on page 5.
3, Plug the mic or instrument into the transmitter and power
up the system,
4. For MlC: Make an initial adjustment of the mixer‘s level
controls that will allow audio through the system,
For INSTRUMENT Make an initial adjustment of the
instrument amplifier input level control that will allow audio
through the system.
5. For MIC, While speaking/singing into the microphone at
typically loud levels, check the AF meter levels on the
receiver. If all five meter bars are consistently illuminated
and distortion is heard through the system, it may be
necessary to adjust the UniPak transmitter audio input level.
To adjust the transmitter audio input level. gently turn the
microphone level trim control counterclockwise until the
topmost receiver AF level meter bar is illuminated only on
audio peaks.
For INSTRUMENT: While playing the instrument at typically
loud levels, check the AF meter levels on the receiver. If all
five meter bars are consistently illuminated and distortion is
heard through the system, it may be necessary to adjust
the UniPak transmitter audio input level. To adjust the
transmitter audio input level, gently turn the instrument
level trim control counterclockwise until the topmost
receiver AF level meter bar is illuminated only on audio
pea ks.
6, For MlC: While again speaking/singing into the microphone
at typically loud levels, adjust the mixer's input trim control
so the highest sound pressure level going into the micro-
phone causes no input overload in the mixer, and yet
permits the mixer’s channel and output level controls to
operate in their “normal“ range (not set too high or too
low)
For INSTRUMENT: While again playing the instrument at
typically loud levels, adjust the receiver's AF Level control
so the highest signal level causes no input overload in the
instrument amplifier and yet permits the amplifier's input
level controls to operate in their “normal" range (not set
too high or too low),
Note: If the mixer cannot be adjusted to operate in its
normal range Without distortion, adjust the receiver's AF
Level Control (turn counterclockwise) until the mixer!
amplifier is no longer overloaded.
Figure E-UniPak Transmitter Open
Antenna
Power-on LED
Audio Input Jack
Instrument/Microphone
Level Trim Controls
Channel
Selector
Batten/skewer
Arm to 1:
Sara _ river on
opposlle slde Transmitter
Door
Receiver Squolch
The squelch control on the back panel of the receiver is preset
at the factory for best system performance (factory setting is
full counterclockwise), but can be adjusted it you must use the
system in an area with considerable RF interference, If there is
interference in the audio, and changing the channel is not an
option, adjust the squelch control so the system Will receive the
signal from your transmitter but will "squelch" or eliminate the
unwanted background RF noise. This adjustment can cause a
reduction in useable range of the wireless transmitter, so set
the control to the lowest position that reliably mutes the
unwanted RF signals.
HF Interference
Please note that wireless frequencies are shared with other
radio servrces. According to Federal Communications
Commission regulations, “VWreless microphone operations are
unprotected from interference from other licensed operations in
the band, If any interference is received by any Government or
non Government operation, the wireless microphone must
cease operation...“ If you need assistance with operation or
frequency selection, please contact your dealer or
Audio-Technica. Extensive wireless information also is available
on the Audio-Technica Web site at www.aud|o~technica,com,
Spec «3 ns'
OVERALL svsmvr
Operating Frequency
Number 07 Channels
Frequency Stability
UHF band, 556 us to 678.500 MHz
to total
£0 005%. Phase Lock Loop ltsqusricy
control
UNIPAK’ TRANSMITIEH
RF Power Output
Spurious Emlsslans
input Connections
Batterias inot included]
12 rnw
Under iudaral regulations
High impedance, low impedance, bias
Two i av AA alkaline
M°d"'a‘"’" Mods FM Currant Consumption iso mA wpical
NO'm' Devlafi‘m x5 k“! Battery Life Approximately 9 hours (depending on
Operating Range 300' tytnoai pottery type and use pattern;
41" F 15° C110 113° F145” Cl Dimensions 2 60“ 1553 mm) W x 3,53' (52 3 mm] H
Operating Tempemture Hangs
Frequency Response
RECEIVER
Receiving System
image Rejection
Signal-to—rioise Ratiu
Total Harmonic Distortion
Sensilimy
intermediate Frequency
100 Hziu lfikHz
Dual independant raceryers, autumallc~
switching dlversity
55 dB nominal, 50 dB minimum
>100 dB at 40 kHz deviation
(Aweigmedl, maximum modulation
40 kHz
<1% (x10 kHz deviation at | Hill
20 dBuV (SM 30 dB at 5 kHz deviation,
lECweightedl
55 75 MH1,1U,7 MHz
Audio Output (AF Level set at "o”l
Unbalanced:
Balanced:
Output Connectors
25 mV (at l kHz, x5 kHz deviation,
100k ohm loadi
|’1.5 mV lat l kHz, as kHz daytanun,
wot grim load)
Unbalanced“ w pttona jack
Balanced: XLRM-tvps
Power SupnN 120V Ac 60 Hz, or 12-isv DC, 350 mA,
wrtn external supply
Dimensions 8 27' (m 0 mm] w x i 73' (44 0 mm) H
Weight
Ancsssuries included
x 5,39“ “62.2 mm) D
2.2 lbs (1.0 kgs)
Two flexible UHF antennas, rackmoum
adapters, AC adapter
N91Wsighl (without batteries)
x 0 89' [21.5 mm) D
2 82 oz (80 gl
MNDHELD TRANS/vin'rERs
RF POM/er OulDul
Spurious Emissions
Microphone Element
Batteries (not included)
Current Consumption
Battery Life
Dimensions
Nat Weight lw‘itnout batteriesl
Accessory Included
12 mW
Under ioderal regulations
Dynamic, unidirectional
Two LEV AA alkaline
i so mA typical
Approxrrnataiy 9 hours (depending
on battmy type and use pattern)
9 02‘ (2290 mm) long x 2 ll' (53 5 mml
maximum diameter
78102122l5gi
ATSASSa Quiet-Flex" stand clamp
t in thoblmelssioi tut-duds denioorn-nt ATU s anats iuii details on its list mornodt to
one
my pflflessionals on request
specifications m star-st to charm without nouns
10
Optional System Accessor s
WIRELESS EssENTlALs' MICROPHONES AND CABLES
ATBZSCW Miniature cardlold condenser Iaval'ler microphone
Includes clothi CI and Windscreen.
MTSSDcW Minlature omn ire nal condenser Isvalier
microphone Includes clothing clip and windscreen.
MTESDcW-TH "Theater" model, same as MTSSOCW except beige cclcr
mic and cable for concealment.
AT83|cW Miniature cardloid condenser Invaller microphone
Includes clothing clip and windscreen.
AT389cW Hesdworn noise-canceling condenser microphone
Includes Windscreen and cable clip,
ATBQBcW Submlniature cardloid condenser Iaveliel microphone.
Includes clorhlng cl‘lp base, viper clip base, magner cllp
baselines single mic holders, two double mic holders and
two windscreens
ATBWCW Subminiature omnidirectional condenser Iaval'ler microphone.
Includes ATESGAK accessory kit,
ATE99cW-TH “Theater” model. same as ATBWCW except beige color rrllc
and cable concealment Includes ATBQSAK-TH accessomklt,
ATM35cW Cardio'ld condenser instrument microphone
Includes ATBME climn instrument mount.
ATM73cW Headwcm cardicid condenser microphone
Includes windscreen
ATM75cw Heedwnm cerdloid condenser microphone.
Includes windscreen.
PROBHECW Headworn hypercardioid dynamic microphone.
Includes windscreen and cable clip
PRO 35ch Cardioid condenser instrument microphone.
Includes ATEAIS cl‘lp—on Instrument mount
AT-GCW Hi-Z instrument/guitar cable with 'l<' phone plug.
XLRW Connecting cable for UniPak transmitter wlth an XLRF-type
input connector, for Lo»Z microphones with XLRM-type
output terminations
REfiIVEH ACCESSORIES
AEW-DA660D UHF (855—580 MHzl active unltv—galn antenna distrjbullon
ATssao
ATWaAzo
ATW~A49
ATW-RAI
flF Cables
system provides two ~i-in, 4—cut" RF channels, connects a
pair of antennas to as many as rour diversity receivers:
cascade ourpui provlded as a dlracnonal coupler. AC
oassrhrough allows daisy-chain AC hookup Deleatable
antenna power. Maral receiver chassis with reinicrcad
mounting aars and rear rack rnounr caoaollny Includes
detachable IEC power cable. IEC pass-through capla, (an RF
cables, Iront—muunt antenna cables and connaarors, four DC
power cables to power up to iour 2000 Series recelvers
Mounts in a single 19- lack space.
Joining-plats kn allows rackamouming rwo Arwahzioo
receivers side-oyslde in a gle nur I9' rack space
Pair or UHF groundalana antennas wrin 7:47 thread ror
mountlng ro microphone srands, are. For use with
ATWaRZlOO receivers Takes RF cables Wlth snc
conneciors. not lncludcd; see RF Cablas below
Pair of UHF wide-band directional LPDA llog perlodlc dlpcle
array) aniannas provide enhanced signal plckup ror UHF
wireless systems rhrougnour a wide band range
(440900 MHz) Each anrenna paddle is matched to 50 ohms
impedance with lntergldl hlgh-quality low-loss snc connectol.
5 dB gain. For permanent or temporary rnsirrllanon; mounra
m 6r. 7 ihreads.
Rack-mount anrenna kit brings anienna inputs to the ironr of
receiver for ease oi saiup, or when receiver is anolosad In a
moral mck Includes a pair or extendible anrannas NOTE.
Two adapter krrs are required when mountlng two receivers
sldscy-side in a sirgle I9" rack space.
Low~|nss design, 50 ohm impedance, wrih BNCAto-BNC
connaorors:
AC12
A625
Acsu
AC1OD
HGEB-tvpe cable (lz'l
RGB-typs cable lz '
FIGS-type cable (50')
RGBivpe cable [I DO'l
TRANSMWER AOCESSDRIES
ATB114
ATBMI
Foam Windscreen for handheld transmitter
Water-resistant pouch for Un'lPak transmltter,
ATEASSa
Quiet-FlaxM stand clamp for handheld iransrnlner, 7.527
threads.
2000 Serles Freguencv Channel Plan
Channel Fruqu-ncz- MHz wen-mm __
1 656.125 45
2 659.375
3 see 000
4 662125 AS
, ifiL , W, . .
6 559,750 47
u 7 __ ,,M _ _ , _ __ ' v,
a 577,000 43
9 678125
to 673 500
Note' All frequencies selected to evord standard analog TV
carrier interierencer
Ten Tips to Obtain the Best Results
Use only fresh alkaline batteries. Do not use "general
purpose" (carbon-zincl batteries
Position the receiver so that it has the fewest possible
obstructions between it and the normal location of the
transmitter Line—ot—srght is best,
The transmitter arid the receiver should be as close
together as conveniently possible, but no closer than
three feet [1 ml.
The receiver antennas should be in the open and away
from any metal Ii mounted in a rack, have the unit on
top, or use an ATW-RAt kit to front—mount the antennas
The transmitter and receiver must be set to the same
channel number.
A receiver cannot receive signals irom two transmitters
at the same time,
7.
10.
It the AF Level control of the receiver is set too high, it
may overdrive the input of the mixer or clip the output of
the receiver, causing distortion. Conversely, if the receiver
output IS set too low, the overall signal-to—norse ratio of
the system may be reduced, Please see Setting Levels
sectlori, pages 7 and 8
You need to change channels when a strong interference
signal is received ta strong RF signal lS shown with the
transmitter am
In the UniPak transmitter, the microphone level trim or
instrument level trim input control not in use should be
set to minimum.
Turn the transmitter off when not in use. Remove the
battery it the transmitter is not to be used for a period oi
time.
Receiver ATW-Fl2 i 00 S/N
UniPakm Body-Pack ATW»T21 D S/N
Transmitter
Handheld Dynamic ATW-T220 S/N
Microphone Transmittal“
For future reference, please record your system information here.
Serul Nutter anp'us on we re: lab-l on m. m at me recewer
5m NWr-pp..m the we elm oaths tea a in. Iurrmtter.
smu Number my; on ma Foe haul on o- mv-nor m m. mmmllm
ii
One-Year Limited Warranty
Audlo~Technica professlonel wrreless syerems purchased in me U.S.A_ ere warremeu lorone yearlrum date 01 purchase bv AudrorTeclrmca u s., Inc,
«AIUSJ to be free or delacls rrr melerlale and workmanshrp, In eyenl ol such uelecl, product will be renar u prommly wlmuur charge or, ar our
apnon, repleoeu wnh a new praflum of equal or superior wlue ll del‘wered ro Alus. or an Aulhorlzed Service Center, prepaid, rogerher wrrh rhe
sales slip or other prool of pumhase date. Prior lppmv-llmm Alas, is required for mum, ms wnnarlly excludes delecrs auero normal wear,
abuse shlppmcl damage, or lallure to use preducl m accordance wlm me rnsuuclions, Thls werrenry is void in rhe eyenr 01 unaurhorueo repalr or
modi ullen, or removal or defacing ol rhe producl labellnu.
For mum approval and shipping Information, Contact lhe Selvlce Dem, Audlor'vschmca u.s.. ln . ml Commerce Dllve. Slaw. O‘nlo 44214
Exoepr lo (he exlsrll precluded by eppllcable srare law, Awe will haw no li-bmry fer Any com'qwmlnl, laud-ml, or spacial damages; nny
mmnry ofmmtrarrreoiliry of mm lo: pmmrm purpose up)". when rlrr's w-mrrrry expirfl.
Thls wamnw gives you specific legal rights, and you may have other nghls which vary from stale lo slate.
Oursiue lhs USA, please cmracr your local dealer lor warrenry detarlsr
Visit our Web Site!
wwmaudio-technica.com
audio-technica,
Audiofl‘echnlca USA, Inc" 1221 Commerce Drive, Stow, 0th 44224 330/686-2600 www.audlo-technica,com
Manama Pslm moor Audra-Tech": us. Inc Pnrlbsdrnlapan
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 12 XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6 About : uuid:b817334f-7e0f-4f6f-943e-30b104df0473 Producer : Adobe Acrobat 6.0.2 Paper Capture Create Date : 2004:10:29 10:38:36-04:00 Creator Tool : HP PrecisionScan Pro 3.0 Modify Date : 2004:10:29 10:50:11-04:00 Metadata Date : 2004:10:29 10:50:11-04:00 Document ID : uuid:71b70a08-3d9a-46e0-8819-5aab505a9c6c Format : application/pdf Creator : HP PrecisionScan Pro 3.0EXIF Metadata provided by EXIF.tools