Audio Technica T310BI BELTPACK WIRELESS MICROPHONE User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1231941
Application ID	+i2+wPwQOhYQJ+InzUzt+g==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	158.78kB (1984762 bits)
Date Submitted	2010-01-22 00:00:00
Date Available	2010-01-25 00:00:00
Creation Date	2009-12-17 10:58:16
Producing Software	Adobe PDF Library 9.0
Document Lastmod	2009-12-17 10:58:32
Document Title	Users Manual
Document Creator	Adobe InDesign CS4 (6.0.4)

3000 Series
Frequency-agile True Diversity UHF Wireless System
-TUNER-
ON
OFF
POWER
ALERT
MODE/SET
UHF SYNTHESIZED DIVERSITY RECEIVER ATW-R3100b
Installation and Operation
3000 Series
Frequency-agile True Diversity UHF Wireless System
French
French
French
Spanish
Spanish
Spanish
Portuguese
Portuguese
Portuguese
German
German
German
Italian
Italian
Italian
Dutch
Dutch
Dutch
Traditional Chinese
Traditional Chinese
Traditional Chinese
Simplified Chinese
Simplified Chinese
Simplified Chinese
Korean
Korean
Korean
2
3000 Series Installation and Operation
(english)
This device complies with part 15 of the FCC Rules. Operation is
subject to the condition that this device does not cause harmful
interference.
This device complies with INDUSTRY CANADA R.S.S. 210, en
conformité avec IC: RSS-210/CNR210. Operation is subject to the
following conditions: 1) This device may not cause harmful interference
and 2) this device must accept any interference received, including
interference which may cause undesired operation.
CAUTION! Electrical shock can result from removal of the receiver
cover. Refer servicing to qualified service personnel. No userserviceable parts inside.
•
•
•
•
•
•
•
•
•
Do not expose batteries to excessive heat such as fire, near heating
units or in direct sunlight.
To prevent fire or shock hazard, do not expose this product to rain
or moisture.
To prevent fire, do not place any naked flame sources (such as
lighted candles) on the apparatus.
To prevent fire, do not cover the ventilation of the apparatus with
newspaper, tablecloths, curtains etc.
Do not expose this apparatus to drips or splashes.
Do not place any objects filled with liquids, such as vases, on the
apparatus.
Do not install this apparatus in a confined space such as a bookcase
or similar unit.
The apparatus should be located close enough to the AC outlet
so that you can easily grasp the AC adapter at any time. In case of
emergency, disconnect the AC adapter quickly.
Always consider environmental issues and follow your local
regulations when disposing of batteries. Do not expose batteries to
excessive heat.
The circuits inside the receiver and transmitter have been precisely
adjusted for optimum performance and compliance with federal
regulations. Do not attempt to open the receiver or transmitter. To do so
will void the warranty, and may cause improper operation.
Notice to individuals with implanted cardiac pacemakers
or AICD devices:
Any source of RF (radio frequency) energy may interfere with normal
functioning of the implanted device. All wireless microphones have
low-power transmitters (less than 0.05 watts output) which are unlikely
to cause difficulty, especially if they are at least a few inches away.
However, since a “body-pack” mic transmitter typically is placed against
the body, we suggest attaching it at the belt, rather than in a shirt
pocket where it may be immediately adjacent to the medical device.
Note also that any medical-device disruption will cease when the RF
transmitting source is turned off. Please contact your physician or
medical-device provider if you have any questions, or experience any
problems with the use of this or any other RF equipment.
RF Interference
Please note that wireless frequencies are shared with other radio
services. According to Federal Communications Commission
regulations, “Wireless microphone operations are unprotected
from interference from other licensed operations in the band. If any
interference is received by any Government or non Government
operation, the wireless microphone must cease operation...” If you
need assistance with operation or frequency selection, please contact
your dealer or Audio-Technica.
Thank you for choosing this Audio-Technica 3000 Series Frequency-agile
True Diversity UHF Wireless System.
The 3000 Series wireless system is available in six UHF frequency
bands to provide flexible performance in a wide variety of regions
worldwide:
Band C
Band D
Band E
Band F
Band G
Band I
Frequency Range
541.500 – 566.375 MHz
655.500 – 680.375 MHz
795.500 – 820.000 MHz
840.125 – 864.900 MHz
721.500 – 746.375 MHz
482.000 – 507.000 MHz
Number of frequencies
996
996
981
953
996
1001
The band letter reference at the end of 3000 Series Stock Numbers
indicates what band the system/component operates in. For simplicity,
model numbers used throughout this manual will reference only the
basic model number without the band indications.
Each wireless system includes a receiver and either a body-pack or
handheld transmitter. UniPak® body-pack transmitter systems may
include an accessory microphone for a particular application. All A-T
Wireless Essentials® microphones and cables, available separately, are
pre-terminated for use with any Audio-Technica 3000 Series wireless
system.
All 3000 Series components feature soft-touch controls for quick, easy
access to a formidable range of functions; an LCD information display
in each unit provides convenient visual indication of unit settings and
operation.
The ATW-R3100b receiver is equipped with automatic frequency
scanning for easy setup. It also features true diversity reception. Two
antennas feed two completely independent RF sections on the same
frequency; automatic logic circuitry continuously compares and selects
the superior received signal, providing better sound quality and reducing
the possibility of interference and dropouts. Soft-touch controls
provide convenient access to a variety of functions, while a backlit LCD
information display provides constant monitoring of system operation,
including indication of the transmitter’s battery status. The receiver is
half-width for a standard 1U 19" rack mount; rack-mount adapters are
included. Two receivers can be mounted side by side, using an optional
AT8630 joining-plate kit.
The versatile ATW-T310b UniPak® body-pack transmitter has both
low- and high-impedance inputs plus a bias connection, for use
with dynamic and electret condenser microphones, as well as Hi-Z
instrument pickups. In addition to its programmable functions, the
transmitter features a three-position sliding cover to limit access, if
desired, to just the Power/Mute button, or to cover all the controls,
as appropriate for the application and user. The ATW-T341b handheld
dynamic microphone/transmitter features the same element used in
the Artist Elite® AE4100 dynamic handheld microphone created for
professional livesound venues. The ATW-T371b handheld condenser
microphone/transmitter features the same element used in the Artist
Series ATM710 cardioid condenser vocal microphone.
Transmitters in the 3000 Series use two 1.5V AA batteries for
economical operation and wide availability. The receiver and both
transmitters have “fuel gauge” battery condition indicators with lowbattery warnings.
An advanced Digital Tone Lock™ tone squelch system in the
ATW-R3100b receiver opens only when a 3000 Series transmitter
3
3000 Series Installation and Operation
(english)
is detected, reducing the possibility of interference. As a result, 3000
Series transmitters and receivers must be used together and should
not be used with components from other Audio-Technica wireless
systems, or with those of other manufacturers. Exception: 3000 Series
components are compatible with Audio-Technica 1800 Series wireless
system components.
Receiver Controls and Functions
Front Panel Controls and Functions
Fig. B
Please note that in multiple-system applications there must be a
transmitter-receiver combination set to a separate frequency for each
input desired (only one transmitter for each receiver). Because the
wireless frequencies are within UHF TV frequency bands, only certain
operating frequencies may be useable in a particular geographic area.
Receiver Installation
Location
For best operation the receiver should be at least 3 ft. (1 m) above the
ground and at least 3 ft. away from a wall or metal surface to minimize
reflections. The transmitter should be at least 3 ft. from the receiver,
as shown in Figure A. Keep antennas away from noise sources such
as digital equipment, motors, automobiles and neon lights, as well as
away from large metal objects.
Fig. A
Output Connections
There are two audio outputs on the back panel: balanced and
unbalanced. Use shielded audio cable for the connection between the
receiver and the mixer. If the input of the mixer is a 1/4" jack, connect a
cable from the 1/4" unbalanced audio output on the back of the receiver
housing to the mixer. If the input of the mixer is an XLR-type input,
connect a cable from the balanced XLR-type audio output on the back
panel to the mixer. The two isolated audio outputs permit simultaneous
feeds to both unbalanced and balanced inputs. For example, both a
guitar amp and a mixer can be driven by the receiver.
Antennas
Attach the included pair of UHF antennas to the antenna input jacks.
The antennas are normally positioned in the shape of a “V” (both 45°
from vertical) for best reception.
Antennas can be remotely located from the receiver. However, due
to signal loss in cables at UHF frequencies, use the lowest-loss RF
cables practical for any cable runs over 8 m / 25 feet. RG8-type is a good
choice. Use only copper-shielded cable, not CATV-type foil-shielded
wire. Audio-Technica offers quality RF cables in four lengths, as well as
remote antennas.
Either passive or active antennas may be used. Both input jacks
offer switchable +12 V DC output on their center pins to operate
Audio-Technica powered antennas or other in-line RF devices if desired.
Up to 60 mA can be drawn from each antenna input jack.
Power Connections
Connect the included AC adapter to the DC power input on the back of
the receiver. Loop the small cord from the DC plug over the cord hook
above the jack, to keep the plug from being detached by an accidental
tug on the cord. Then plug the AC adapter into an AC power outlet.
Operation of the receiver is controlled by the front-panel Power switch.
-TUNER-
ON
ALERT
POWER
MODE/SET
OFF
UHF SYNTHESIZED DIVERSITY RECEIVER ATW-R3100b
1. POWER SWITCH: Press Power switch in and the receiver
readouts will light.
2. ALERT INDICATOR: The Alert Indicator lights:
(a) When the receiver is in the Function Edit mode,
(b) When no RF signal is received from transmitter,
(c) When only one or two RF signal-strength bars are on,
(d) When the transmitter is in the Mute mode,
(e) When audio modulation level from the transmitter is close to the
clipping point (AF +3/+6 bars),
(f) When only one bar of the Battery “fuel gauge” is on (transmitter
		 battery is weak).
3. LCD WINDOW: Backlit screen indicates control settings and 		
operational readings. See Figure D for examples.
4. TUNER OPERATION INDICATOR: Indicates which Tuner (A or B) has
the better reception and is in operation. The “B” indicator also lights
to serve as confirmation of Mode/Set button entries.
5. UP/DOWN BUTTONS: Press Up or Down arrow buttons, in
conjunction with the Mode/Set button, to step through menus,
select operating frequency and edit receiver function choices.
6. MODE/SET BUTTON: Use in conjunction with the Up/Down arrow
buttons to step through menus, choose operating frequency, initiate
automatic scanning and select receiver function options.
-TUNER-
ON
OFF
POWER
ALERT
MODE/SET
UHF SYNTHESIZED DIVERSITY RECEIVER ATW-R3100b
7. MOUNTING ADAPTERS: For mounting the receiver in any standard
19" rack. Attach adapters to the receiver with the screws supplied
and remove the four receiver feet. (Use optional AT8630 joiningplate kit to mount two ATW-R3100b receivers side-by-side.)
Rear Panel Controls and Functions
Fig. C
10
12
15
AF
LEVEL
ANT. B
ANT. A
GROUND
AF OUT
GROUND LIFT BALANCED
11
12~18V
AF OUT
UNBALANCED DC500 mA
13
14
8. ANTENNA INPUT JACK: BNC-type antenna connector for Tuner “B.”
Attach the antenna directly, or extend it with a low-loss antenna
cable.
9. ANTENNA INPUT JACK: Input for Tuner “A.” Attach the antenna
directly, or extend it with a low-loss antenna cable.
10. AF LEVEL CONTROL: Adjusts audio output level of both AF Output
jacks; maximum output is fully clockwise.
11. GROUND LIFT SWITCH: Disconnects the ground pin of the
balanced output jack (12) from ground. Normally, the switch should
4
3000 Series Installation and Operation
(english)
be to the left (ground connected). If hum caused by a ground loop
occurs, slide switch to the right (ground lifted).
12. BALANCED AUDIO OUTPUT JACK: XLRM-type connector. A
standard 2-conductor shielded cable can be used to connect the
receiver output to a balanced microphone-level input on a mixer or
integrated amplifier.
13. UNBALANCED AUDIO OUTPUT JACK: 1/4" phone jack. Can be
connected to an unbalanced aux-level input of a mixer, guitar amp
or tape recorder.
14. POWER INPUT JACK: Connect the DC plug from the included in-line
AC adapter.
15. CORD HOOK: Loop the small DC cord around the cord hook to keep
the DC plug from pulling out accidentally.
move to “QUIT”. Press the Mode/Set button once to exit the
menu and return the receiver to normal operation. (“RF” and “AF”
will reappear in the window, indicating the return to normal receiver
operation, with the receiver’s audio output again enabled.)
Frequency Group Selection
To select a frequency scan group, press the Mode/Set button, then use
the arrow button until the desired group appears in the display. To store
the selected frequency scan group, press the Mode/Set button to enter
the desired group; then use the arrow button to start the scan. When a
flashing number is displayed, press and hold Mode/Set button to select
the frequency. See detailed instructions in System Operation.
Power On/Off
To turn the receiver on, press in the Power switch. The Alert light and
the LCD window will come on (about 1-2 seconds). The operating
frequency will be displayed in the window after the power-up sequence.
To turn the receiver off, press the Power switch again.
How to Restore Default Settings
To return all the receiver functions to their original factory default
settings, first turn the receiver off. Then hold in the Mode/Set button
while pressing and releasing the Power switch. The LCD will briefly
show “RESET”, followed by “WAIT” (release the Mode/Set button),
before commencing normal-mode operation at the default settings.
LCD Window
The LCD (Liquid Crystal Display) presents a great deal of setup and
operating information clearly and conveniently. (See Figure D for
examples.)
When the receiver is in the Menu or Edit mode, its audio output is
silenced. Once control-setting operations are completed (or Escape
is used), normal receiver operation will resume with its audio output
restored.
flashing
Fig. D
MHz
RF BATT
AF
+6
+3
-3
-6
-9
-16
-20
D1. Normal Receiver Operation
(Transmitter off)
MHz
D2. Menu Mode (Frequency)
MHz
D3. Edit Mode (Frequency)
Up/Down Arrow Buttons
In conjunction with the Mode/Set button, the arrow buttons permit
moving through the menu of functions, and they offer a choice of
settings within each function.
Mode/Set Button
The Mode/Set button shifts the receiver from normal operation into
Menu mode and, in conjunction with the Up/Down arrow buttons,
permits selection of different features and changing of their stored
values in the Edit mode.
How to Make Setting Changes
1. From the normal operating mode, press the Mode/Set button once
to enter the Function Menu mode. (Only the frequency will remain
in the LCD window, and the receiver’s audio output will be cut off.)
2. Use the Up/Down arrow buttons to reach the desired function.
The value in the LCD window is the current setting for that function.
3. Press the Mode/Set button once again to open the list of available
choices for that function. The value will flash, indicating that it can
be changed (Edit mode).
4. Use the arrow buttons to go through the available choices, stopping
on the desired new choice.
5. (a) To accept and enter the new choice, press and hold the Mode/
Set button until “STORED” appears in the LCD. This changes the
value and puts the function of the buttons back at Menu level (step
2 above). (The “B” tuner light will come on while the Mode/Set
button is depressed, to confirm its action.)
(b) To “back out” of the Edit mode without making a new choice,
simply press the Mode/Set button once. The word “ESCAPE” will
appear in the window and the function of the buttons will revert to
the Menu level (step 2 above), without making any changes.
6. Repeat this selection process for any other function changes
desired. When finished with any changes, use the arrow buttons to
While in the Edit mode, if no action is taken for approximately 30
seconds (no buttons pressed), the receiver will “back out” to the Menu
mode. Similarly, after about 30 seconds of inaction in the Menu mode,
the receiver will “back out” to normal receiver operation with audio
output restored.
High-pass Filter
Internal high-pass filter circuitry may be set to four positions: Highpass Off, or a 6 dB, 12 dB or 18 dB slope at 150 Hz. The default
setting is Off (“HP OFF”). Increasing the slope of the high-pass filter
further suppresses unwanted low frequencies, while maintaining the
frequency response in the desired audio range.
Meter Hold Setting
When activated (“MH ON”), this function permits the bar-meters in
the LCD window to capture and display the highest-level “AF” audio
modulation (a solid bar) and the lowest-level “RF” signal (a flashing bar)
received from the transmitter. This is particularly useful when setting
up the system initially, during a sound-check, or when diagnosing
operating problems. The default setting is Off (“MH OFF”).
When the Meter Hold is On, it is possible to reset it – to obtain a new
set of RF and AF readings – without turning it off-and-on using the
Menu/Edit functions. Simply press the transmitter’s Power/Mute button
once (to mute the transmitter) and wait until the receiver’s Alert light
comes on, indicating the Mute condition. Then press the transmitter’s
Power/Mute button once again, to un-mute the transmitter. After the
Alert light goes out, a new set of min/max RF/AF readings will be
indicated on the bar-meters. (Note that, depending upon the digital
updating-and-confirming sequence of the Mute condition data from
the transmitter, it may take several seconds for the Alert light condition
to change. The Meter Hold function is not reset until the Alert light
has turned on, then turned off.)
Digital Tone Lock™ Squelch
The 3000 Series employs a unique Digital Tone Lock squelch system
that provides enhanced rejection of interference. In addition to providing
highly effective control of unwanted noise, the Tone Lock signal from
the transmitter also conveys data on the transmitter’s battery condition
and mute status back to the receiver for display.
5
3000 Series Installation and Operation
(english)
The squelch level is adjustable from 15 dB (the default value) to 39 dB
in 6 dB steps. Increasing the squelch level – also called “tightening
the squelch” – can cause a reduction in useable range of the wireless
transmitter, so use the lowest value that reliably mutes the unwanted
RF signals. (If interference is a problem, first consider trying a different
frequency.)
Antenna Power
The antenna input jacks also can provide +12V DC output on their
center pins to power inline RF devices. A maximum of 60 mA can be
drawn from each of the jacks. While an accidental short-circuit will not
harm the internal 12V supply, make certain that an antenna cable shield
does not contact the center conductor. Antenna Power (“ANT.PWR”) is
selected (switched on or off) from the LCD menu.
Pre-coordinated Frequency Scan Groups 1-9
The nine scan groups provided on the 3000 Series receivers simplify
the selection of usable frequencies in a multi-channel wireless system.
If you are using multiple systems, stay within one of the nine frequency
groups for all of your systems. The available frequencies within each
group have been selected for simultaneous use, eliminating the
frustration encountered when trying to select compatible frequecies in
a multi-channel system.
Scan Groups 8 and 9 have been designed to allow for use on adjoining
stages. Use Group 8 on one stage and Group 9 on a second nearby
stage. Or use these two groups in two different rooms, with one room
using Group 8, and the second using Group 9.
Default
Setting*
Choices
(Edit)▲▼
Wraparound**
(Receiver powers-up at Frequency)
Lowest in
band†
All frequencies
in band
Yes
High-pass
Filter
HP OFF
HP OFF, HP– 6,
HP–12, HP–18
No
▲▼ Meter
MH OFF
MH OFF
MH ON
Yes
SQ 15 dB
SQ 15 dB to
SQ 39 dB in
6 dB steps
No
Antenna
Power
OFF
PWR OFF
PWR ON
Yes
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 1
No
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 2
No
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 3
No
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 4
No
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 5
No
▲▼
Frequency
▲▼
▲▼
Hold
Squelch
▲▼
Function
Menu
Default
Setting*
Choices
(Edit)▲▼
Wraparound**
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 6
No
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 7
No
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 8
No
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 9
No
QUIT
Press Mode/
Set to exit
–
▲▼ Quit
(exit Menu)
* To reset to Default values, hold in the Mode/Set button while
pressing the Power button to turn on the unit.
** Continue in the same Up/Down direction and choices “wrap around”
to the other end of the range.
† Band I: 482.000 – 507.000 MHz; Band C: 541.500 – 566.375 MHz;
Band D: 655.500 – 680.375 MHz; Band G: 721.500 – 746.375 MHz;
Band E: 795.500 – 820.000 MHz; Band F: 840.125 – 864.900 MHz
Transmitter Controls And Functions
Receiver Functions
Function
Menu
Receiver Functions (continued)
Refer to Figures E, F, G and H for an overview of transmitter features
and controls.
LCD Window
The backlit Liquid Crystal Display presents a great deal of setup and
operating information clearly and conveniently (See examples in Fig. J).
The LCD in the transmitters is designed for greatest contrast and best
viewing with the window rotated somewhat away from the viewer
(about 30 degrees), not straight-on, for a more convenient holding/
viewing position. The display is illuminated with a backlight when you
power on the device and when you press Set to access transmitter
functions. The backlight remains on during the Set process, only
turning off if no action is taken within 30 seconds or if Quit is pressed;
otherwise, it automatically turns off in ten seconds.
Power/Mute Button
The transmitters have a combination Power and Mute switch. When
used in combination with the programmed choices explained below,
the various functions available to the transmitter user may be tailored to
fit personal preferences or particular situations of use.
Power On/Off
To turn the transmitter on, press and hold the Power/Mute button until
the green power indicator and the LCD window come on (about 1-2
seconds). The operating frequency will show in the window after the
power-up sequence.
To turn the transmitter off, press and hold the Power/Mute button again,
until the green power indicator and the LCD window are extinguished
(about 1-2 seconds). The LCD window will show “PWR.OFF” before
shutdown.
Mute Off/On
When the transmitter is muted, it produces RF with no audio signal
6
3000 Series Installation and Operation
(english)
modulation. When the transmitter is un-muted, it produces both RF and
audio.
To mute the transmitter (cut off the audio, but continue the RF output),
press and release the Power/Mute button once. A small “MUTE” will
appear in the LCD window, just below the frequency (Fig. M-2) and the
power/mute LED will change from green to red.
To un-mute the transmitter (restore the audio), press and release the
Power/Mute button once again. The “MUTE” will disappear from the
LCD window and the power/mute LED will change from red to green.
Fig. E
Sliding
Control Cover
(3-position)
Up/Down
Arrows
Backlit
LCD Window
Power/Mute
Button
Band C: Blue
Band D: Green
Band E: Black
Band F: Gray
Band G: Red
Band I: Orange
Antenna
Power-on LED
ATW-T310b UHF TRANSMITTER
Audio Input Jack
Battery
Door
Fig. F
Power/Mute
Button
Set Button
Mounting Clip
Power-on LED
Frequency Group Selection
To select a frequency scan group, press the Set button, then use the up
or down arrow until the desired group appears in the display. To store
the selected frequency scan group, press the Set button to enter the
desired group; then use the arrow button to find desired frequency.
Press and hold Set button to select the frequency. See detailed
instructions in System Operation.
Fig. G
Fig. H
Setting
Description
NO.LOC
The normal Power and Mute functions are fully
operational.
ALL.LOC
Both the Power and Mute functions are locked
into their status as of the time “ALL.LOC” is
applied. (Power On, and Mute either On or Off.)
Note: ALL.LOC must be re-accessed and the
setting changed to turn the transmitter off.
MUT.LOC
In this mode, the audio cannot be muted.
The Power functioning is unaffected. (If MUT.LOC is
applied while the transmitter is muted, pressing
the Power/Mute button once will return to
un-muted operation; thereafter the Mute function
is disabled until the setting is changed again.)
PWR.LOC
Power is locked On as of the time “PWR.LOC”
is applied. The Mute functioning is unaffected.
Note: When in the PWR.LOC mode, the
transmitter may be turned off by: (1) Re-accessing
the .LOC Menu and changing the setting, or
(2) Removing and re-installing the batteries. When
the transmitter is turned on again, it will power-up
in the NO.LOC mode. (Only the PWR. LOC
function will change when batteries are removed;
all other settings remain stored in memory.)
If an attempt is made to take an action that currently is locked
out, the LCD will display “LOCKED” briefly, then return to its
previously-displayed contents.
Audio Input Selector
The UniPak® body-pack transmitter provides input connections for
both low-impedance (Lo-Z) microphones and high-impedance (Hi-Z)
instruments. A wide range of Audio-Technica Wireless Essentials®
microphones and cables is available pre-terminated with the appropriate
professional latching connector. Selection of the desired input –
microphone or instrument – is made through the function menu.
Depending upon the input selected, a small “MIC” or “INST” will
show in the LCD window, just below the frequency. (In the handheld
transmitter, only “MIC” will show in the LCD window.)
Antenna Housing
Backlit
LCD Window
Power/Mute Locks
Programmable Power/Mute Locks limit the functioning of the Power/
Mute button as desired for particular users and/or applications. Power
can be locked On; Mute can be locked Off. Selection of the desired
locks, if any, is made through the function menu:
Backlit
LCD Window
Up/Down
Arrows
SET
Power-on LED
Set Button
Restore Default Settings
A “PRESET” selection in the menu permits resetting of all transmitter
functions to their factory-default values.
1. Press the Set button once to move to Menu mode.
2. Press the Up arrow twice to move to “PRESET” in the LCD window.
3. Press the Set button once and “LOAD” will appear in the LCD.
4. Press and hold the Set button until “DEF” appears in the LCD.
5. Press and hold the Set button until “LOADED” appears briefly in the
LCD. The window will then revert to “PRESET”.
6. Press the Down arrow once to move to “QUIT”.
7. Press the Set button once to exit the Menu mode and return to
normal operation, with all factory-default settings restored.
7
3000 Series Installation and Operation
(english)
UniPak® Transmitter Functions
Function
Menu
Default
Setting*
Handheld Transmitter Functions
Choices
(Edit)▲▼
Wrap-around
(Transmitter powers-up at Frequency)
Function
Menu
Default
Setting*
Choices
(Edit)▲▼
Wraparound**
(Transmitter powers-up at Frequency)
▲▼ Frequency
Lowest in
band†
All frequencies
in band
Yes
▲▼
Frequency
Lowest in
band†
All frequencies
in band
Yes
▲▼ RF
RF LOW
RF LOW, RF HI
Yes
▲▼
RF Power
+6 dB
–6 dB, 0 dB,
+6 dB, +12 dB
No
▲▼
NO.LOC
NO.LOC, ALL.LOC,
MUT.LOC,
PWR.LOC
Yes
Power
▲▼ Audio
Input
Level
▲▼ Power/Mute
Locks
▲▼ Input
MIC
MIC, INST
Yes
▲▼ Group
Select
Lowest in
frequency
group
All frequencies
in Group 1
Yes
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 2
Yes
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 3
Yes
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 4
Yes
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 5
Yes
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 6
Yes
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 7
Yes
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 8
Yes
▲▼ Group
Lowest in
frequency
group
All frequencies
in Group 9
Yes
▲▼ Reset
to
PRESET
LOAD (b) hold
until: DEF (c)
hold until:
LOADED
–
Press Set to
exit
–
Defaults
▲▼ Quit
(exit Menu)
QUIT
RF LOW
RF LOW, RF HI
Yes
Audio Input
Level
Dynamic
+6 dB
No
Condenser**
+6 dB
-6 dB, 0 dB,
+6 dB, +12 dB,
0 dB, +6 dB,
+12 dB
Power/
Mute Locks
NO.LOC
NO.LOC, ALL.LOC,
MUT.LOC,
PWR.LOC
Yes
▲▼
No
▲▼
Group 1
Lowest in
frequency
group
All frequencies
in Group 1
Yes
▲▼
Group 2
Lowest in
frequency
group
All frequencies
in Group 2
Yes
▲▼
Group 3
Lowest in
frequency
group
All frequencies
in Group 3
Yes
▲▼
Group 4
Lowest in
frequency
group
All frequencies
in Group 4
Yes
▲▼
Group 5
Lowest in
frequency
group
All frequencies
in Group 5
Yes
▲▼
Group 6
Lowest in
frequency
group
All frequencies
in Group 6
Yes
▲▼
Group 7
Lowest in
frequency
group
All frequencies
in Group 7
Yes
▲▼
Group 8
Lowest in
frequency
group
All frequencies
in Group 8
Yes
▲▼
Group 9
Lowest in
frequency
group
All frequencies
in Group 9
Yes
▲▼
Reset to
Defaults
PRESET
LOAD (b) hold
until: DEF (c)
hold until:
LOADED
--
Quit
(exit Menu)
QUIT
Press Set to
exit
–
▲▼
* Continue in the same Up/Down direction and choices “wrap around”
to the other end of the range.
** Additional 6 dB pad switch on capsule.
† Band I: 482.000 – 507.000 MHz; Band C: 541.500 – 566.375 MHz;
Band D: 655.500 – 680.375 MHz; Band G: 721.500 – 746.375 MHz;
Band E: 795.500 – 820.000 MHz; Band F: 840.125 – 864.900 MHz
8
3000 Series Installation and Operation
(english)
Transmitter Setup
Battery Selection and Installation
Each transmitter uses two 1.5V AA batteries, not included. Alkaline
type is recommended; other types of 1.5V AA batteries (including
rechargeable) may be used, however performance may vary. Always
replace both batteries. Make certain the transmitter power is Off before
replacing batteries.
UniPak ® Transmitter Battery Installation
1. Open the battery compartment door as follows:
Slide door lock down to the unlocked position. Pinch the release
arrows together to open the compartment. (Fig. J)
2. Observe correct polarity as marked on the metal contacts on the
door and carefully insert two fresh 1.5V AA alkaline batteries (Fig. K).
3. Close the door, making certain the latch clicks securely in place.
4. Slide the door lock up to the locked position.
Fig. J						
Fig. K
Release
Arrows
Door Lock
Fig. L
Serial Number
Start from this end
to remove batteries
Handheld Transmitter Battery Installation
1. While holding the lower body cover (near the LCD window), grasp
the upper part of the transmitter body just below the grille and
unscrew it at least four complete turns (Fig. G); then slide the
lower body cover down until it stops (Fig. H). Once the cover
has been lowered, turn the transmitter over to reveal the battery
compartment on the side opposite the LCD window.
2. Observe correct polarity as marked inside the battery compartment
and carefully insert two fresh 1.5V AA batteries (Fig. L). Insert the
first battery and slide it down. Then insert the second battery,
bottom first, into the space remaining. Make certain the batteries
are fully seated in the battery compartment.
3. Slide the lower body cover back up the body, then screw the
housing together. Do not overtighten.
Note: Remove batteries from the handheld transmitter starting at
the bottom (– end) of the top battery (Fig. L). The top (+ end) of the
top battery is captured in a recess and will not come straight out.
Battery Condition Indicator
After the batteries are installed, turn the power on by pressing and
holding the Power/Mute button. The small power-on LED (Fig. E/F)
should light green and the LCD window should come on. If this does
not happen, the batteries are installed incorrectly or they are dead.
The transmitter’s “fuel gauge” battery indicator displays a maximum of
four bar segments. When it flashes “LOW.BAT”, the batteries should
be replaced immediately to ensure continued operation. (The receiver
also displays transmitter battery condition in the LCD window with
bar segments; the Alert indicator comes on to warn of a low-battery
condition.)
UniPak® Transmitter Input Connection
Connect an audio input device (microphone or guitar cable) to the audio
input jack on the transmitter. A number of Audio-Technica professional
microphones and cables are available separately, pre-terminated with
a UniPak input connector. The cable connector latches automatically
when inserted into the transmitter jack. To unlatch and remove the
connector, simply pull up on the connector’s knurled metal collar.
UniPak® Transmitter Antenna
The UniPak transmitter includes a field-replaceable flexible antenna.
For best results, allow the antenna to extend to its full length from the
transmitter. If the received signal is marginal, experiment with different
transmitter positions on your body or instrument; or try repositioning
the receiver or using remote receiver antennas. Since the transmitter
antenna simply screws in, check it occasionally to make certain it
is snugly attached (finger-tight). Do not change the length of the
transmitting antenna.
Handheld Transmitter Antenna
The antenna for the handheld mic/transmitter is in the black,
non-metallic section at the bottom of the unit (Fig. F). For best results,
hold the mic/transmitter naturally, around its painted metal case;
holding or otherwise covering the antenna housing may reduce the
operating range.
UniPak® Transmitter Mounting Clip
The UniPak transmitter’s mounting clip may be installed with the case
positioned either “up” or “down,” depending upon which is preferred
for the application. To turn the clip around, pull the ends of the clip
out of the two holes on the sides of the transmitter case (Fig. E) and
reinstall it facing in the opposite direction.
9
3000 Series Installation and Operation
(english)
System Operation
Turn the receiver on by pressing in the Power switch. Do not switch on
the transmitter yet.
The Alert indicator and the LCD window will light up; the normaloperation LCD display will appear after 1-2 seconds (Fig. D-1). If
any of the bars show in the “RF” bar-graph meter, there may be RF
interference in the area. If this occurs, select another frequency as
explained below. (If the Meter Hold function has been selected, one of
the RF bars will be flashing, indicating the lowest RF level received.)
Selecting/Setting Frequency
Selection of the desired operating frequency is made through the
function menus. It’s usually best to start by setting the receiver’s
frequency, to determine there is no local interference on that frequency.
Then, always make certain to set the transmitter to the receiver’s exact
frequency. The receiver’s unique Digital Tone Lock system squelches
the audio only, permitting any RF energy on the frequency to show on
the “RF” bar-meter.
Note: It is often convenient to start with the factory-default frequency,
if there is no RF energy showing on the RF bar meter.
Using the Automatic Scan Function to Set Receiver Frequency
1. Press the Mode/Set button once; then the “RF” and “AF” scales will
disappear from the window and only the frequency will appear in
the LCD window. (The receiver is now in the Menu mode.) See
Figure D-2.
2. Use the Up arrow button to reach Group 1 through Group 9. Press
the Mode/Set button once to select one of these nine scan groups.
The lowest frequency in the selected scan group will appear in the
LCD window.
3. Press the Up arrow button to begin the scan. “G SCAN” will flash in
the LCD window.
4. The first available frequency will flash in the LCD window. To
activate this frequency selection, press and hold the Mode/Set
button until the word “STORED” appears in the LCD window. (If you
do not wish to complete this particular selection, just press the
Mode/Set button once. The word “ESCAPE” will appear briefly in
the window and the receiver will return to the Menu mode.)
5. After you have activated your frequency selection (step 4), the “RF”
and “AF” scales will reappear in the window, indicating the return to
normal operation.
6. If you are using multiple systems, all frequencies must be selected
from the same group (Group 1 through Group 9). After completing
the first receiver’s scan and frequency selection, set the transmitter
to the same frequency (see Setting Transmitter Frequency
instructions); leave the transmitter On, and run the next
receiver’s automatic scan function. Always set a receiver-transmitter
pair to the same frequency before using the automatic scan function
to select a frequency for the next receiver. “End” will show on
the receiver display when no further usable frequencies remain in
the selected scan plan.
NOTES ON USING THE RECEIVER SCAN FEATURE:
• Selecting low power on your transmitter can be helpful for multiple
system setup, if you are experiencing problems with radio
frequency interference.
• To prevent raised noise floors that a receiver scan might interpret as
radio frequency interference: during setup, keep all transmitters at
least three feet apart and at least 15 feet from the receivers.
Setting Receiver Frequency Manually
1. Press the Mode/Set button once; then only the frequency will
appear in the LCD window. (The receiver is now in the Menu mode.)
See Figure D-2.
2. Press the Mode/Set button again; the Alert light will come on and
the first three digits of the frequency will flash in the window.
(The receiver is now in the Edit mode, Fig. D-3.)
3. Use the Up/Down arrow buttons to change the first three digits
(MHz) to the desired frequency. Choose a frequency appropriate
for your area, avoiding frequencies with active TV channels. Press
either arrow for single steps, or hold down either arrow for rapid
cycling through the band. Frequencies “wrap around” to the other
end of the range when the top or bottom of the band is reached.
4. Press the Mode/Set button once to set the first three digits to the
desired frequency.
5. Use the Up/Down arrow buttons to change the second three digits
(kHz) to the desired frequency. Again, be certain to choose a
frequency appropriate for your area, avoiding frequencies with active
TV channels.
6. To activate this frequency selection, press and hold the Mode/Set
button until the word “STORED” appears in the receiver’s window.
(If you do not wish to complete this particular selection, just press
the Mode/Set button once. The word “ESCAPE” will appear briefly
in the window and the receiver will return to the Menu mode.)
7. When finished entering a frequency, press the Down arrow button
once to move to “QUIT”. Then press the Mode/Set button once to
exit the menu. The “RF” and “AF” scales will reappear in the
window, indicating the return to normal operation.
Transmitter On…
Turn on the transmitter by pressing and holding the Power/Mute button
(Fig. E/F) for a second or two, until the green power indicator and the
LCD window have come on.
Fig. M
BATT
BATT
MIC
M-1. Normal Operation
* ATW-T310b only: “INST”
EDIT
MENU
BATT
M-3. Menu Mode (Frequency)
MUTE MIC
M-2. Operation with Mute On
MIC
BATT
MIC
M-4. Edit Mode (Frequency)
Setting Transmitter Frequency
1. Press the Set button once and the small word “MENU” will appear
above the frequency. Press the Set button again and the small
flashing word “EDIT” will appear to the right of “MENU”. See
Figures M-3 and M-4.
2. Use the Up/Down arrow buttons to change the first three digits of
the transmitter frequency. Press either arrow for single steps, or
hold down either arrow for rapid cycling through the range.
Frequencies “wrap around” when the top or bottom of the band is
reached. Select the exact frequency displayed on the receiver.
3. Press the Set button once to set the first three digits to the desired
frequency.
10
3000 Series Installation and Operation
(english)
4. Use the Up/Down arrow buttons to change the second three digits
to the desired frequency.
5. To activate this frequency selection, press and hold the Set button
until the word “STORED” appears in the transmitter’s window. (If
you do not wish to complete this selection, just press the Set button
once: the word “ESCAPE” will appear briefly in the window and the
transmitter will return to the Menu mode.)
6. When finished entering a frequency, press the Up arrow button
once to move to “QUIT”. Then press the Set button once to exit
the menu. The word “MENU” in the transmitter window will go off,
indicating the return to normal operation.
When the transmitter is switched on and in normal operation, the
receiver’s “RF” signal-level bars will display from bottom to top,
with more bars indicating increased signal reception. For optimum
performance at least four, and preferably five or more, of the RF
indicators should be displayed.
Setting Transmitter Audio Input Levels
Correct adjustment of transmitter audio input, receiver audio output,
and mixer/amplifier input and output levels is important for optimum
system performance.
ATW-T310b and ATW-T341b Transmitters
A 4-position audio input gain setting, selected through the function
menu, serves to match the audio input level to the transmitter for best
modulation with minimum distortion. Available choices are +12 dB,
+6 dB, 0 dB and - 6 dB. The default value is +6 dB. Select the highest
setting that does not result in over-modulation with the highest audio/
instrument input levels (an AF indication on the receiver no higher than
“0”).
ATW-T371b Transmitter
A 3-position audio input gain setting, selected through the function
menu, serves to match the audio input level to the transmitter for best
modulation with minimum distortion. Available choices are +12 dB, +6
dB, and 0 dB. The default value is +6 dB. In addition, a mechanical pad
switch on the condenser capsule (inside the screw-on wire mesh grille)
can provide another 6 dB of attenuation. For best performance, adjust
the input level using the function menu choices, keeping the capsule’s
mechanical switch at 0 dB. If more audio attenuation is needed than the
menu provides, then set the capsule’s pad switch to - 6 dB.
RF Power Adjustment
RF power may be set to “RF HI” (30 mW nominal) or “RF LOW”
(10 mW nominal) through the function menu. The default setting is “RF
LOW”. While the High setting normally provides maximum operating
range, the Low setting will help extend battery life. The Low setting
may also be preferred in multichannel systems, or when operating very
close to the receiver, to reduce the possibility of interference
or overload.
RF Interference
Please note that wireless frequencies are shared with other radio
services. According to Federal Communications Commission
regulations, “Wireless microphone operations are unprotected
from interference from other licensed operations in the band. If any
interference is received by any Government or non-Government
operation, the wireless microphone must cease operation...” If you
need assistance with operation or frequency selection, please contact
your dealer or Audio-Technica.
Ten Tips to Obtain the Best Results
1. Use only fresh alkaline batteries. Do not use “general purpose”
(carbon-zinc) batteries.
2. Position the receiver so that it has the fewest possible obstructions
between it and the normal location of the transmitter. Line-of-sight
is best.
3. The transmitter and the receiver should be as close together as
conveniently possible, but no closer than three feet (1 m).
4. Avoid placing the receiver in a low or shielded location where the
transmitter and receiver antennas are not within line-of-sight. If
necessary, use remotely-located receiver antennas.
5. Avoid placing the receiver near computers or other RF generating
equipment.
6. The receiver and transmitter must be set to the same frequency.
7. A receiver cannot receive signals from two transmitters at the same time.
8. Do not obstruct the handheld transmitter’s antenna (located at the
base) or attached body-pack transmitter’s antenna with your hands.
9. You need to change frequencies 1) when a strong interference
signal is received, 2) when audio quality is poor due to weak RF, or
3) during multiple-system operation in order to select an
interference-free frequency.
10. Turn the transmitter off when not in use. Remove the batteries if the
transmitter is not to be used for a period of time.
11
3000 Series Installation and Operation
(english)
Troubleshooting Guide
Receiver is not on (LCD window does not light).
• Receiver Power switch is not pressed in.
• Small DC power cord from included in-line power supply
		 is not plugged into jack on back of receiver. (Use the cord
		 hook to secure it.)
• The in-line power supply is not plugged into AC power outlet.
• AC power is not present at the AC outlet.
Receiver is on (LCD window lights).
- No sound - Alert light is OFF:
“RF”, “AF” and “BATT” legends do not appear in LCD.
• Receiver is in the Menu mode.
“RF” and “AF” level meters both show good signals.
• AF Level control on back of receiver not turned up (clockwise).
Note: If the “AF” level meter shows a good signal on the receiver
when the transmitter is receiving audio input, and the AF Level
control is turned up, then the problem is in connections to or
control settings on the mixer, amplifier, etc.
Only “RF” level meter shows good signal; no “AF” signal.
• No sound input to mic.
• ATW-T310b body-pack only: Wrong input selected (“INST”
or “MIC”).
Receiver is on (LCD window lights).
- No sound - Alert light is ON:
“RF”, “AF” and “BATT” legends do not appear in LCD, and
LCD is flashing.
• Receiver is in the Edit mode.
“RF” and “AF” level meters both show good signals.
• The transmitter audio level is too high
(“+3”/”+6” on receiver).
• Batteries may be weak. (Check “BATT” fuel gauge.)
Only “RF” level meter shows good signal; no “AF”signal.
• Transmitter may be muted. (Note: Normally it takes several
seconds for the Alert light to turn off/on after the transmitter
mute is switched off/on.)
Neither the “RF” nor the “AF” level meter shows any signal.
• Receiver antennas not connected.
• Transmitter is turned off.
• Transmitter batteries are dead or missing.
• Transmitter is set to a different frequency.
• Transmitter and receiver not in same Band.
Receiver is on (LCD window lights).
- Distorted sound - Alert light is ON:
“RF” and/or “AF” level meters may show good signals.
• The transmitter audio level is too high (“+3”/”+6” on receiver).
• Received RF level may be too low (only one or two bars).
• Batteries may be weak; check “BATT” fuel gauge. (Sound may
or may not be distorted.)
Momentary loss of sound/noisy sound as transmitter is
moved around performing area.
• Transmitter and receiver antennas not in line-of-sight (or perhaps
		 too far apart). Adjust positions of units so they are visible to each
		 other/closer together; use remote antennas located closer to the
		 transmitter location.
•
•
Signal blockage or interference from large metal objects, other
wireless units located too close and/or on incompatible
frequencies, computer or lighting equipment.
Squelch setting may be set “tighter” than it needs to be.
(Recommended squelch setting is the minimum/default value,
15 dB.)
Tip: Use the Meter Hold function to help identify and resolve (or
at least avoid) RF problem locations.
With transmitter on, received signal is noisy or contains
extraneous sounds.
• Batteries may be weak. Check “BATT” fuel gauge and “RF”
		 meter level.
• Local TV transmissions on this frequency.
• Nearby sources of RF interference, such as computers, lighting
		 equipment, etc.
• Two transmitters may be operating on the same frequency.
		 Locate and turn one off or change its frequency.
• In multiple-system use, two (or more) incompatible frequencies
		 may have been selected.
Please note: This manual is offered in other languages
at www.audio-technica.com
12
3000 Series Installation and Operation
(english)
Specifications†
Overall System
UHF Operating Frequencies
Frequency Range
Band C:
541.500 to 566.375 MHz
Band D:
655.500 to 680.375 MHz
Band E:
795.500 to 820.000 MHz
Band F:
840.125 to 864.900 MHz
Band G:
721.500 to 746.375 MHz
Band I:
482.000 to 507.000 MHz
Number of Frequencies
996
996
981
953
996
1001
Not all frequencies are available in all areas. Please check with local regulations.
Minimum Frequency Step
Modulation Mode
Maximum Deviation
Dynamic Range
Total Harmonic Distortion
Operating Range
25 kHz
FM
±35 kHz
> 110 dB (A-weighted), typical
< 1% (at 1 kHz, ±17.5 kHz deviation)
100 m (300'), typical
Open range environment with no interfering signals.
Operating Temperature Range
-5 ºC to +45 ºC
23 º F to 113 ºF
Battery and LCD performance may be reduced at very low temperatures.
Frequency Response
ATW-R3100b Receiver
Receiving System
Image Rejection
RF Sensitivity
Maximum Output Level
XLR, balanced:
¼" (6.3 mm), unbalanced:
Antenna Input
Power Requirements
Dimensions		
70 Hz to 15 kHz (+1 dB, -3 dB)
True diversity
60 dB nominal, 55 dB minimum
24 dBuV at 60 dB S/N ratio
(50 ohms termination)
+9 dBV
+7 dBV
BNC-type, 50 ohms
Bias voltage 12V DC, 60 mA, each
12-18V DC, 500 mA
210.0 mm (8.27") W x
164.4 mm (6.47") D x
44.0 mm (1.73") H
Handheld Transmitters
RF Power Output
High: 30 mW; Low: 10 mW,
(switchable), at 50 ohms
Spurious Emissions
Following federal and national
regulations
Microphone Element
ATW-T341b
Dynamic cardioid
ATW-T371b
Condenser cardioid
Batteries		
Two 1.5V AA, not included
Battery Life		
High: 6 hours (alkaline)
Low: 8 hours (alkaline)
Depending on battery type and use pattern.
Dimensions
ATW-T341b
237.0 mm (9.33") long,
48.0 mm (1.89") diameter
ATW-T371b
240.0 mm (9.45") long,
50.0 mm (1.97") diameter
Net Weight
ATW-T341b
284 g (10.0 oz), without batteries
ATW-T371b
277 g (9.8 oz), without batteries
Accessory Included
AT8456a Quiet-Flex™ stand clamp
† In the interest of standards development, A.T.U.S. offers full details on its test methods to
other industry professionals on request.
Specifications are subject to change without notice.
CAUTION: U.S. Public Safety/Security Restrictions
(Private Land Mobile Radio Services)
Avoid the frequencies/channels listed below in each of the following
U.S. metropolitan areas (as of November 2009). Refer to www.fcc.gov
for updates
Urbanized
Area
Not including BNC connectors or feet.
Net Weight 		
Accessories Included
ATW-T310b UniPak® Transmitter
RF Power Output
Spurious Emissions
Input Connection
1.1 kg (38.8 oz), without accessories
Two flexible UHF antennas;
AC adapter (country dependent);
rack-mount adapters
High: 30 mW, Low: 10 mW
(switchable), at 50 ohms
Following federal and national
regulations
Four-pin Locking Connector
Pin 1: GND, Pin 2: INST INPUT,
Pin 3: MIC INPUT, Pin 4: DC BIAS +5V
Batteries 		
Two 1.5V AA, not included
Battery Life		
High: 6 hours (alkaline)
Low: 8 hours (alkaline)
Depending on battery type and use pattern.
Dimensions		
66.0 mm (2.60") W x
24.0 mm (0.94") D x
87.0 mm (3.43") H
Net Weight		
81 g (2.9 oz), without batteries
Geographical Center
Bands (MHz)
TV Channels
North Latitude
West Longitude
Boston, MA
42°21’24.4”
71°03’23.2”
470–476,
482–488
14, 16
Chicago, IL1
41°52’28.1”
87°38’22.2”
470–476,
476–482
14, 15
Cleveland, OH 2
41°29’51.2”
81°49’49.5”
470–476,
476–482
14, 15
Dallas/Fort
Worth, TX
32°47’09.5”
96°47’38.0”
482–488
16
Detroit, MI 3
42°19’48.1”
83°02’56.7”
476–482,
482–488
15, 16
Houston, TX
29°45’26.8”
95°21’37.8”
488–494
17
Los Angeles,
CA 4
34°03’15.0”
118°14’31.3”
470–476,
482–488,
506–512
14, 16, 20
Miami, FL
25°46’38.4”
80°11’31.2”
470–476
14
New York, NY/
NE NJ
40°45’06.4”
73°59’37.5”
470–476,
476–482,
482–488
14, 15, 16
Philadelphia, PA
39°56’58.4”
75°09’19.6”
500–506,
506–512
19, 20
Pittsburgh, PA
40°26’19.2”
79°59’59.2”
470–476,
494–500
14, 18
San Francisco/
Oakland, CA
37°46’38.7”
122°24’43.9”
482–488,
488–494
16, 17
Washington,
DC/MD/VA
38°53’51.4”
77°00’31.9”
488–494,
494–500
17, 18
In the Chicago, IL, urbanized area, channel 15 frequencies may be used for paging operations 		
in addition to low power base/mobile usages, where applicable protection requirements for 		
ultrahigh frequency television stations are met.
Channels 14 and 15 are not available in Cleveland, OH, until further order from the Commission.
Channels 15 and 16 are not available in Detroit, MI, until further order from the Commission.
Channel 16 is available in Los Angeles, CA, for use by eligibles in the Public Safety Radio Po
13
3000 Series Installation and Operation
(english)
C-Band Scan Plan (541.500 – 566.375 MHz)
F-Band Scan Plan (840.125 – 864.900 MHz)*
Scan - 1
Scan - 2
Scan - 3
Scan - 4
Scan - 5
Scan - 6
Scan - 7
Scan - 8
Scan - 9
Scan - 1
Scan - 2
Scan - 3
Scan - 4
Scan - 5
Scan - 6
Scan-7
Scan - 8
Scan - 9
542.750
541.500
541.500
548.125
541.500
541.700
542.750
541.500
541.750
840.375
840.500
846.850
846.250
846.100
855.275
863.100
840.125
840.375
545.500
542.750
542.125
548.375
541.900
542.100
543.250
542.000
542.250
840.625
840.750
847.400
847.200
846.600
855.900
863.500
840.625
840.875
547.125
544.375
543.500
548.875
543.000
544.775
543.500
543.250
543.500
852.875
852.875
848.525
847.900
847.575
856.175
864.300
841.375
841.625
547.375
544.750
544.000
549.125
544.975
546.225
544.500
544.750
545.000
853.125
853.125
849.925
850.825
848.050
857.625
864.700
841.875
842.125
549.750
545.750
546.250
550.375
546.025
546.975
545.250
545.250
545.500
853.625
853.625
851.050
851.350
850.425
857.950
856.300
843.375
843.625
550.375
547.500
548.250
550.625
548.700
548.900
546.500
546.000
546.250
853.875
853.875
851.600
856.900
858.425
860.900
856.800
844.625
844.875
550.625
554.250
549.750
551.125
549.500
550.100
547.500
546.500
546.750
855.375
855.500
859.100
857.725
859.250
861.200
857.050
845.125
845.375
557.250
556.125
555.750
551.375
549.900
552.775
548.250
554.300
554.550
855.625
855.750
859.725
859.350
859.825
861.750
858.300
848.125
848.375
557.500
557.500
556.625
556.650
560.225
554.975
558.750
559.125
559.375
856.125
856.250
861.050
860.100
861.500
863.125
858.550
856.600
856.850
10
559.250
559.375
558.250
556.900
560.975
557.700
559.500
561.125
561.375
10
856.375
856.500
861.800
860.575
861.900
863.375
859.050
857.100
857.350
11
559.500
560.000
559.375
557.400
562.025
561.500
560.500
561.625
561.875
11
860.750
860.750
845.750
840.325
841.325
840.875
859.300
857.850
858.100
12
562.000
561.875
560.125
557.650
564.700
562.225
561.750
562.875
563.125
12
861.000
861.000
861.300
842.825
843.250
841.125
840.375
858.350
858.600
13
563.375
562.250
561.500
558.900
565.100
564.500
562.500
564.375
564.625
13
861.500
861.500
856.600
848.900
857.325
842.375
840.875
859.850
860.100
14
563.625
563.250
564.000
559.150
565.900
564.900
563.500
564.875
565.125
14
861.750
861.750
857.950
848.325
843.825
842.625
842.375
860.350
860.600
15
566.000
565.500
564.250
559.650
566.300
565.700
563.750
565.625
565.875
15
863.875
863.750
849.425
855.200
853.500
843.125
842.625
861.100
861.350
16
566.250
566.000
566.125
559.900
552.225
566.100
564.250
566.125
566.375
16
864.125
864.000
852.850
863.650
855.575
843.375
843.375
861.600
861.850
* When operating in the deregulated frequency range (863.000 – 864.900 MHz) in countries following the R&TTE
directive, transmitter power must be set to “LOW” (10 mW)
D-Band Scan Plan (655.500 – 680.375 MHz)
G-Band Scan Plan (721.500 – 746.375 MHz)
Scan - 1
Scan - 2
Scan - 3
Scan - 4
Scan - 5
Scan - 6
Scan - 7
Scan - 8
Scan - 9
Scan - 1
Scan - 2
Scan - 3
Scan - 4
Scan - 5
Scan - 6
Scan - 7
Scan - 8
Scan - 9
655.500
655.875
655.500
662.125
656.225
656.025
655.500
655.500
655.750
722.750
721.500
721.500
721.500
722.025
721.500
721.750
721.500
721.750
658.000
656.250
655.750
662.375
656.975
656.775
655.750
656.000
656.250
725.500
722.750
722.125
721.750
722.775
722.225
722.500
722.000
722.250
658.375
658.500
656.625
662.875
658.025
658.225
656.500
657.250
657.500
727.125
724.375
723.500
722.500
724.000
724.500
723.500
723.250
723.500
659.250
659.750
658.500
663.125
658.775
660.900
657.750
658.750
659.000
727.375
724.750
724.000
722.750
724.700
724.900
723.750
724.750
725.000
659.500
660.000
658.750
664.375
662.300
661.700
659.250
659.250
659.500
729.750
725.750
726.500
724.250
726.300
725.700
726.750
725.250
725.500
661.500
660.500
659.500
664.625
663.000
662.100
659.500
660.000
660.250
730.375
727.500
728.250
726.250
727.000
726.100
727.250
726.000
726.250
662.375
664.375
662.750
665.125
664.225
664.025
666.500
660.500
660.750
730.625
734.250
729.750
726.500
728.225
728.025
728.500
726.500
726.750
662.750
665.500
665.250
665.375
664.975
664.775
672.500
668.300
668.550
737.250
736.125
735.750
727.500
728.975
728.775
731.250
734.300
734.550
669.625
671.625
671.250
670.650
674.025
668.900
673.250
673.125
673.375
737.500
737.500
736.625
740.500
738.025
738.225
737.250
739.125
739.375
10
671.750
672.000
672.375
670.900
674.775
669.300
675.750
675.125
675.375
10
739.250
739.375
738.250
741.500
738.775
738.975
739.500
741.125
741.375
11
674.750
674.000
673.125
671.400
676.000
674.225
676.250
675.625
675.875
11
739.500
740.000
739.375
741.250
740.000
740.900
742.750
741.625
741.875
12
675.750
674.500
674.125
671.650
676.700
674.975
678.750
676.875
677.125
12
742.000
741.875
740.125
742.250
740.700
741.300
743.500
742.875
743.125
13
676.125
675.750
674.500
672.900
678.300
677.300
679.500
678.375
678.625
13
743.375
742.250
741.500
745.125
742.300
742.100
744.500
744.375
744.625
14
678.000
676.750
675.375
673.150
679.000
678.100
679.750
678.875
679.125
14
743.625
743.250
744.000
745.375
743.000
744.025
745.250
744.875
745.125
15
678.250
678.250
678.625
673.650
680.225
678.500
663.750
679.625
679.875
15
746.000
745.500
744.250
746.125
744.225
745.500
745.750
745.625
745.875
16
679.500
680.250
679.125
673.900
668.700
680.025
675.500
680.125
680.375
16
746.250
746.000
746.125
746.375
744.975
746.225
739.250
746.125
746.375
E-Band Scan Plan (795.500 – 820.000 MHz)
I-Band Scan Plan (482.000 – 507.000 MHz)
Scan - 1
Scan - 2
Scan - 3
Scan - 4
Scan - 5
Scan - 6
Scan - 7
Scan - 8
Scan - 9
Scan - 1
Scan - 2
Scan - 3
Scan - 4
Scan - 5
Scan - 6
Scan - 7
Scan - 8
Scan - 9
798.925
798.900
795.550
798.250
795.825
796.000
796.500
795.500
795.750
482.100
482.225
482.225
488.125
482.025
482.225
482.500
482.000
482.250
800.525
799.475
796.775
799.200
796.950
796.700
796.900
796.000
796.250
482.350
482.475
482.475
488.375
482.775
482.975
483.250
482.500
482.750
801.475
801.425
797.050
799.900
797.500
797.100
797.700
796.750
797.000
483.100
483.225
483.225
488.875
484.000
484.500
483.500
483.750
484.000
803.025
802.025
797.750
802.825
798.600
797.900
800.775
797.250
797.500
483.350
483.475
483.475
489.125
484.700
485.300
484.250
485.250
485.500
803.550
803.075
806.850
803.350
802.425
806.300
806.100
798.250
798.500
484.850
484.975
484.975
490.375
486.300
485.700
486.750
485.750
486.000
804.825
803.625
807.400
808.900
809.325
807.000
806.500
798.750
799.000
486.850
486.975
486.975
490.625
487.000
486.500
487.250
486.500
486.750
805.150
806.925
811.100
809.725
810.425
810.775
810.225
799.500
799.750
487.100
487.225
487.225
491.125
488.225
488.025
489.750
487.000
487.250
811.700
809.125
811.725
811.350
811.250
812.700
810.975
800.000
800.250
488.100
488.225
494.150
491.375
488.975
488.775
495.500
494.800
495.050
812.825
811.575
813.050
812.100
811.825
813.500
812.500
809.150
809.400
501.000
500.875
497.275
502.650
498.025
498.225
497.250
499.625
499.875
10
813.125
813.300
813.800
812.575
813.500
813.900
813.700
809.650
809.900
10
502.000
501.875
497.775
502.900
498.775
500.500
499.750
501.625
501.875
11
816.625
815.425
799.400
800.900
813.900
800.975
798.100
810.400
810.650
11
502.250
502.125
498.025
503.400
500.000
500.900
500.250
502.125
502.375
12
817.175
816.525
808.650
796.100
797.900
802.775
800.025
810.900
811.150
12
504.250
504.125
499.075
503.650
500.700
501.700
504.500
503.375
503.625
13
817.425
817.100
813.300
801.725
806.600
808.225
813.300
811.900
812.150
13
505.750
505.625
499.325
504.900
504.225
502.100
505.250
504.875
505.125
14
817.975
817.925
798.875
804.575
807.575
800.225
817.500
812.400
812.650
14
506.000
505.875
499.850
505.150
504.975
504.775
505.750
505.375
505.625
15
819.050
818.225
804.825
807.200
808.050
808.975
818.225
813.150
813.400
15
506.750
506.625
506.625
505.650
506.025
506.225
506.500
506.125
506.375
16
819.600
819.025
809.475
807.900
812.950
810.025
816.975
813.650
813.900
16
507.000
506.875
506.875
505.900
506.775
506.975
499.500
506.625
506.875
14
Warranty
U.S. Two-Year Limited Warranty
This product and selected Audio-Technica brand products purchased in the U.S.A.
from an authorized Audio-Technica (A.T.U.S.) dealer are warranted for two years from
date of purchase by A.T.U.S. to be free of defects in materials and workmanship. To
identify those products, go to www.audio-technica.com/usawarranties. In event of a
defect, End-User’s exclusive remedy is at A.T.U.S.’ election, the cost of repair, refund
of the purchase price in the form of credit or cash, or replacement of the product.
The product must be delivered to A.T.U.S. or an Authorized Service Center, prepaid,
together with the sales slip or other proof of purchase date. This warranty excludes
defects due to normal wear, abuse, shipping damage, or failure to use product in
accordance with instructions. This warranty is void in the event of unauthorized repair
or modification, or removal or defacing of the product labeling.
For U.S. service return instructions and procedure please go to:
www.audio-technica.com/returninstructions.
A.T.U.S.’ warranty is to the End User only. Except for A.T.U.S.’ said express
warranty, A.T.U.S. MAKES NO WARRANTIES, EXPRESS OR IMPLIED, WITH
RESPECT TO THE PRODUCTS. A.T.U.S. SPECIFICALLY MAKES NO WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Except to the extent precluded by applicable state law, A.T.U.S. IS NOT LIABLE
FOR CONSEQUENTIAL, INCIDENTAL, DIRECT OR SPECIAL DAMAGES ARISING,
DIRECTLY OR INDIRECTLY, IN RESPECT OF SUCH PRODUCTS OR USE OR
FAILURE THEREOF, WHETHER BASED ON BREACH OF WARRANTY, NEGLIGENCE,
STRICT LIABILITY, TORT OR OTHERWISE.
This warranty gives you specific legal rights, and you may have other rights which
vary from state to state.
Outside the U.S.A., please contact your local dealer for warranty details.
Audio-Technica U.S., Inc.
1221 Commerce Drive
Stow, Ohio 44224
UK and EU/Europe
Disclaimer
Audio-Technica operates a policy of continuous development. Audio-Technica reserves
the right to make changes and improvements to any of the products described in this
document without prior notice.
Under no circumstances shall Audio-Technica be responsible for any loss of data or
income or any special, incidental, consequential or indirect damages howsoever caused.
The contents of this document are provided “as is”. Except as required by applicable
law, no warranties of any kind, either express or implied, including, but not limited to,
the
implied warranties of merchantability and fitness for a particular purpose, are made in
relation to the accuracy, reliability or contents of this document. Audio-Technica reserves
the right to revise this document or withdraw it at any time without prior notice.
The availability of particular products may vary by country. Please check with the distributor for your territory. In some countries there may be restrictions in using this equipment. Please check with your local radio frequency authorities.
Two-Years Limited Warranty
Audio-Technica microphones and accessories purchased in the UK and EU / Europe
are guaranteed for two years from date of purchase by Audio-Technica Ltd. to be free
of defects in materials and workmanship. In the event of such defect, product will be
repaired promptly without charge or, at our option, replaced with a new product of
equal or superior value, if the faulty product is delivered to Audio-Technica Ltd., prepaid,
together with the proof of purchase.
Prior approval from Audio-Technica Ltd. is required for return. This warranty excludes
defects due to normal wear, abuse, shipping damage, or failure to use product in accordance with instructions. This warranty is void in the event of unauthorized repair or
modification.
For return approval and shipping information, contact the Service Department, AudioTechnica Ltd. Tel: +44 (0)113 277 1441.
Outside the U.K, please contact your local dealer for warranty details.
15
Disposal of Old Electrical & Electronic Equipment (Applicable in European countries with
separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated as
household waste. Instead it shall be handed over to the applicable collection point for the recycling
of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product. The recycling of materials will
help to conserve natural resources. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service or the shop where you
purchased the product.
Tratamento de Equipamentos Eléctricos e Electrônicos no final da sua vida útil (Aplicável em
países Europeus com sistemas de recolha independentes)
Este símbolo no produto ou na sua embalagem indica que este não deve ser tratado como resíduo
doméstico. Ao invés, será colocado no ponto de recolha destinado à reciclagem de equipamento
eléctrico e electrônico. Assegurandose que este produto é despejado correctamente, você irá
prevenir potenciais consequências negativas para o meio ambiente bem como para a saúde humana,
que de outra forma poderiam ocorrer pela manipulação imprópria deste produto. A reciclagem dos
materiais contribuirá para a conservação dos recursos naturais. Para obter mais informação detalhada
sobre a reciclagem deste produto, por favor contacte o município acentos onde reside, os serviços
de recolha de resíduos da sua área ou a loja onde o produto foi adquirido.
Deutsch Entsorgung von gebrauchten elektrischen und elektronischen Geräten (Anzuwenden
in den europäischen Ländern mit einem separaten Sammelsystem für diese Geräte)
Das Symbol auf dem Produkt oder seiner Verpackung weist darauf hin, dass dieses Produkt
nicht als normaler Haushaltsabfall zu behandeln ist, sondern an einer Annahmestelle für das
Recycling von elektrischen und elektronischen Geräten abgegeben werden muss. Durch Ihren
Beitrag zum korrekten Entsorgen dieses Produkts schützen Sie die Umwelt und die Gesundheit
Ihrer Mitmenschen. Umwelt und Gesundheit werden durch falsches Entsorgen gefährdet.
Materialrecycling hilft den Verbrauch von Rohstoffen zu verringern. Weitere Informationen über das
Recycling dieses Produkts erhalten Sie von Ihrer Gemeinde, den kommunalen Entsorgungsbetrieben
oder dem Geschäft, in dem Sie das Produkt gekauft haben.
Trattamento del dispositivo elettrico od elettronico (Applicabile in tutti I paesi dell’Unione
Europea che utilizzano un sistema di raccolta differenziata)
Questo simbolo sul prodotto o sulla confezione indica che il prodotto non deve essere riposto in
un punto di raccolta adibito a rifiuti domestici. Deve invece essere trattato nel punto di raccolta
appropriato per il riciclo di apparecchi elettrici ed elettronici. Assicurandovi che questo prodotto sia
smaltito correttamente, contribuirete a prevenire potenziali conseguenze negative per l’ambiente e
per la salute che potrebbero altrimenti essere causate dal uno smaltimento inadeguato. Il riciclaggio
dei materiali aiuta a conservare le risorse naturali. Per informazioni più dettagliate circa il riciclaggio di
questo prodotto, potete contattare il vostro ufficio comunale, il servizio locale di smaltimento rifiuti
oppure il negozio dove l’avete acquistato.
Traitement des appareils électriques et électroniques en fin de vie (Applicable dans les pays
européens disposant de systèmes de collecte sélective)
Ce symbole, apposé sur le produit ou sur son emballage, indique que ce produit ne doit pas être
traité avec les déchets ménagers. Il doit être remis à un point de collecte approprié pour le recyclage
des équipements électriques et électroniques. En s’assurant que ce produit est bien mis au rebut
de manière appropriée, vous aiderez à prévenir les conséquences négatives potentielles pour
l’environnement et la santé humaine. Le recyclage des matériaux aidera à conserver les ressources
naturelles. Pour toute information supplémentaire au sujet du recyclage de ce produit, vous pouvez
contacter votre municipalité, votre déchetterie ou le magasin où vous avez acheté le produit.
Verwijdering van oude Elektrische en Elektronische Apparaten (Toepasbaar in de Europese
landen met gescheiden ophaalsysteem)
Het symbool op het product of op de verpakking wijst erop dat dit product niet als huishoudafval
mag worden behandeld. Het moet echter naar een plaats worden gebracht waar elektrische en
elektronische apparatuur wordt gerecycled. Als u ervoor zorgt dat dit product op de correcte manier
wordt verwijderd, voorkomt u voor mens en milieu negatieve gevolgen die zich zouden kunnen
voordoen in geval van verkeerde afvalbehandeling. De recyclage van materialen draagt bij tot het
vrijwaren van natuurlijke bronnen. Voor meer details in verband met het recyclen van dit product,
neemt u het best contact op met de gemeentelijke instanties, het bedrijf of de dienst belast met de
verwijdering van huishoudafval of de winkel waar u het product hebt gekocht.
Tratamiento de los equipos eléctricos y electrónicos al final de su vida útil (Aplicable en países
europeos con sistemas de recogida selectiva de residuos)
Este símbolo en su equipo o su embalaje indica que el presente producto no puede ser tratado
como residuos domésticos normales, sino que deben entregarse en el correspondiente punto de
recogida de equipos eléctricos y electrónicos. Asegurándose de que este producto es desechado
correctamente, Usted está ayudando a prevenir las consecuencias negativas para el medio ambiente
y la salud humana que podrían derivarse de la incorrecta manipulación de este producto. El reciclaje
de materiales ayuda a conservar los recursos naturales. Para recibir información detallada sobre
el reciclaje de este producto, por favor, contacte con su ayuntamiento, su punto de recogida más
cercano o el distribuidor donde adquirió el producto.
Håndtering af udtjent elektrisk og elektronisk udstyr (Gælder for europæiske lande med
separate indsamlingssystemer)
Dette symbol på produktet eller emballagen angiver, at produktet ikke må behandles som
husholdningsaffald. Det skal i stedet indleveres på en deponeringsplads specielt indrettet til
modtagelse og genbrug af elektrisk og elektronisk udstyr. Ved at sikre, at produktet bortskaffes
korrekt, forebygges de eventuelle negative miljø- og sundhedsskadelige påvirkninger, som en
ukorrekt affaldshåndtering af produktet kan forårsage. Genbrug af materialer vil medvirke til at bevare
naturens ressourcer. Yderligere information om genbrug af dette produkt kan fås hos myndighederne,
det lokale renovationsselskab eller i butikken, hvor produktet blev købt.
Omhändertagande av gamla elektriska och elektroniska produkter (användbara i europeiska
länder med separata insamlingssystem)
Symbolen på produkten eller emballaget anger att produkten inte får hanteras som hushållsavfall.
Den skall i stället lämnas in på uppsamlingsplats för återvinning av el- och elektronikkomponenter.
Genom att säkerställa att produkten hanteras på rätt sätt bidrar du till att förebygga eventuella
negativa miljö- och hälsoeffekter som kan uppstå om produkten kasseras som vanligt avfall.
Återvinning av material hjälper till att bibehålla naturens resurser. För ytterligare upplysningar
om återvinning bör du kontakta lokala myndigheter eller sophämtningstjänst eller affären där du
köpte varan.
Pozbywanie się zużytego sprzętu (Stosowane w krajach europejskich posiadających system
selektywnej zbiórki odpadów)
Takie oznaczenie na produkcie lub jego opakowaniu wskazuje, że produkt nie może być traktowany jako
odpad komunalny lecz powinno się go dostarczyć do odpowiedniego punktu zbiórki sprzętu elektrycznego
i elektronicznego w celu recyklingu. Zapewniając prawidłową dyspozycję dotyczącą produktu, zapobiega
się jego negatywnemu działaniu na środowisko oraz zdrowie ludzi, jakie mogłoby wystąpić w przypadku
niewłaściwego postępowania. Recykling materiałów pomoże w ochronie bogactw naturalnych. W celu
uzyskania bardziej szczegółowych informacji na temat recyklingu tego produktu, należy skontaktować się
urzędem miejskim, ze służbami oczyszczania miasta lub ze sklepem, w którym ten produkt został zakupiony.
Утилизация электрического и электронного оборудования (директива применяется в странах, где
действуют система раздельного сбора отходов).
Данный знак на устройстве или его упаковке обозначает, что данное устройство нельзя утилизировать
вместе с прочими бытовыми отходами. Его следует сдать в соответствующий приемный пункт
переработки электрического и электронного оборудования. Неправильная утилизация данного изделия
может привести к потенциально негативному влиянию на окружающую среду и здоровье людей,
поэтому для предотвращения подобных последствий необходимо выполнять специальные требования
по утилизации этого изделия. Переработка данных материалов поможет сохранить природные ресурсы.
Для получения более подробной информации о переработке этого изделия обратитесь в местные органы
городского управления, службу сбора бытовых отходов или в магазин, где было приобретено изделие.
Käytöstä poistetun sähkö- ja elektroniikkalaitteen hävitys (Euroopan maiden
keräysjärjestelmät)
Symboli, joka on merkitty tuotteeseen tai sen pakkaukseen, osoittaa, että tätä tuotetta ei saa
käsitellä talousjätteenä. Tuote on sen sijaan luovutettava sopivaan sähkö-ja elektroniikkalaitteiden
kierrätyksestä huolehtivaan keräyspisteeseen. Tämän tuotteen asianmukaisen hävittämisen
varmistamisella autetaan estämään sen mahdolliset ympäristöön ja terveyteen kohdistuvat
hailtavaikutukset, joita voi aiheutua muussa tapauksessa tämän epäasianmukaisesta jätekäsittelystä.
Materiaalien kierrätys säästää luonnonvaroja. Tarkempia tietoja tämän tuotteen kierrättämisestä saa
paikallisesta kunnantoimistosta.
Audio-Technica U.S., Inc.
1221 Commerce Drive, Stow, Ohio 44224 USA +1 (330) 686-2600
Audio-Technica Limited
Old Lane, Leeds LS11 8AG England +44 (0) 113 277 1441
Audio-Technica (Greater China) Limited
Unit K, 9/F., Kaiser Est. (Ph.2) 51 Man Yue St. Kowloon, HK. +852-2356-9268
Audio-Technica (S.E.A.) Pte. Ltd.
No 1 Ubi View, #01-14 Focus One, Singapore 408555 +65-6749-5686
Audio-Technica Corporation
2206, Naruse Machida, Tokyo Japan
©2010 Audio-Technica U.S., Inc.
audio-technica.com
P52165

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.2-c063 53.352624, 2008/07/30-18:05:41
Create Date                     : 2009:12:17 10:58:16-05:00
Metadata Date                   : 2009:12:17 10:58:32-05:00
Modify Date                     : 2009:12:17 10:58:32-05:00
Creator Tool                    : Adobe InDesign CS4 (6.0.4)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 6724 bytes, use -b option to extract)
Instance ID                     : uuid:32358f46-8068-c24c-8f12-40e82268eab8
Document ID                     : xmp.did:793F424E222068118263F6ECCA183DB0
Original Document ID            : xmp.did:058011740720681195FE9CE16554C163
Rendition Class                 : proof:pdf
History Action                  : created, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:058011740720681195FE9CE16554C163, xmp.iid:068011740720681195FE9CE16554C163, xmp.iid:078011740720681195FE9CE16554C163, xmp.iid:088011740720681195FE9CE16554C163, xmp.iid:098011740720681195FE9CE16554C163, xmp.iid:F87F117407206811852EA6E4D054D917, xmp.iid:F97F117407206811852EA6E4D054D917, xmp.iid:FA7F117407206811852EA6E4D054D917, xmp.iid:FB7F117407206811852EA6E4D054D917, xmp.iid:FD7F117407206811852EA6E4D054D917, xmp.iid:FE7F117407206811852EA6E4D054D917, xmp.iid:FF7F117407206811852EA6E4D054D917, xmp.iid:0080117407206811852EA6E4D054D917, xmp.iid:5AB355D524206811852EA6E4D054D917, xmp.iid:5BB355D524206811852EA6E4D054D917, xmp.iid:5CB355D524206811852EA6E4D054D917, xmp.iid:5DB355D524206811852EA6E4D054D917, xmp.iid:5EB355D524206811852EA6E4D054D917, xmp.iid:F77F117407206811994CCFD1D5D7AC70, xmp.iid:F87F117407206811994CCFD1D5D7AC70, xmp.iid:F97F117407206811994CCFD1D5D7AC70, xmp.iid:FA7F117407206811994CCFD1D5D7AC70, xmp.iid:FB7F117407206811994CCFD1D5D7AC70, xmp.iid:FC7F117407206811994CCFD1D5D7AC70, xmp.iid:FD7F117407206811994CCFD1D5D7AC70, xmp.iid:FE7F117407206811994CCFD1D5D7AC70, xmp.iid:FF7F117407206811994CCFD1D5D7AC70, xmp.iid:0080117407206811994CCFD1D5D7AC70, xmp.iid:F84D101C27206811994CCFD1D5D7AC70, xmp.iid:F94D101C27206811994CCFD1D5D7AC70, xmp.iid:FA4D101C27206811994CCFD1D5D7AC70, xmp.iid:FB4D101C27206811994CCFD1D5D7AC70, xmp.iid:FC4D101C27206811994CCFD1D5D7AC70, xmp.iid:FD4D101C27206811994CCFD1D5D7AC70, xmp.iid:FE4D101C27206811994CCFD1D5D7AC70, xmp.iid:FF4D101C27206811994CCFD1D5D7AC70, xmp.iid:004E101C27206811994CCFD1D5D7AC70, xmp.iid:014E101C27206811994CCFD1D5D7AC70, xmp.iid:024E101C27206811994CCFD1D5D7AC70, xmp.iid:EEA28EAD3F206811994CCFD1D5D7AC70, xmp.iid:EFA28EAD3F206811994CCFD1D5D7AC70, xmp.iid:F77F1174072068118263F6ECCA183DB0, xmp.iid:F87F1174072068118263F6ECCA183DB0, xmp.iid:F97F1174072068118263F6ECCA183DB0, xmp.iid:FA7F1174072068118263F6ECCA183DB0, xmp.iid:FB7F1174072068118263F6ECCA183DB0, xmp.iid:FC7F1174072068118263F6ECCA183DB0, xmp.iid:FD7F1174072068118263F6ECCA183DB0, xmp.iid:FE7F1174072068118263F6ECCA183DB0, xmp.iid:00801174072068118263F6ECCA183DB0, xmp.iid:703F424E222068118263F6ECCA183DB0, xmp.iid:713F424E222068118263F6ECCA183DB0, xmp.iid:723F424E222068118263F6ECCA183DB0, xmp.iid:733F424E222068118263F6ECCA183DB0, xmp.iid:743F424E222068118263F6ECCA183DB0, xmp.iid:763F424E222068118263F6ECCA183DB0, xmp.iid:773F424E222068118263F6ECCA183DB0, xmp.iid:783F424E222068118263F6ECCA183DB0, xmp.iid:793F424E222068118263F6ECCA183DB0, xmp.iid:7A3F424E222068118263F6ECCA183DB0, xmp.iid:7CA9EC812D2068118263F6ECCA183DB0, xmp.iid:7DA9EC812D2068118263F6ECCA183DB0, xmp.iid:7EA9EC812D2068118263F6ECCA183DB0, xmp.iid:7FA9EC812D2068118263F6ECCA183DB0, xmp.iid:80A9EC812D2068118263F6ECCA183DB0, xmp.iid:81A9EC812D2068118263F6ECCA183DB0, xmp.iid:82A9EC812D2068118263F6ECCA183DB0, xmp.iid:83A9EC812D2068118263F6ECCA183DB0, xmp.iid:43E794491220681183B3D655BEECAAB6, xmp.iid:44E794491220681183B3D655BEECAAB6, xmp.iid:FE944DB24720681183B3D655BEECAAB6, xmp.iid:FF944DB24720681183B3D655BEECAAB6, xmp.iid:01801174072068119618D0E50EB9AC0A, xmp.iid:02801174072068119618D0E50EB9AC0A, xmp.iid:03801174072068119618D0E50EB9AC0A, xmp.iid:F77F1174072068119457EA3313C3F940, xmp.iid:F87F1174072068119457EA3313C3F940, xmp.iid:01801174072068118F629D266610711E, xmp.iid:02801174072068118F629D266610711E, xmp.iid:03801174072068118F629D266610711E, xmp.iid:04801174072068118F629D266610711E, xmp.iid:05801174072068118F629D266610711E, xmp.iid:0180117407206811994CDD267888B84B, xmp.iid:FD7F1174072068118DBB8D9D9BC0ABB0
History When                    : 2009:11:03 10:21:33-05:00, 2009:11:03 11:26:15-05:00, 2009:11:03 11:26:15-05:00, 2009:11:03 15:15:58-05:00, 2009:11:03 15:29:59-05:00, 2009:11:04 11:11:51-05:00, 2009:11:04 11:16:08-05:00, 2009:11:04 11:25:24-05:00, 2009:11:04 11:51:10-05:00, 2009:11:04 12:23:06-05:00, 2009:11:04 12:29:23-05:00, 2009:11:04 12:32:11-05:00, 2009:11:04 13:36:18-05:00, 2009:11:04 14:01:27-05:00, 2009:11:04 14:48:28-05:00, 2009:11:04 14:49:03-05:00, 2009:11:04 14:59:40-05:00, 2009:11:04 15:00:25-05:00, 2009:11:05 08:02:56-05:00, 2009:11:05 08:15:55-05:00, 2009:11:05 08:47:02-05:00, 2009:11:05 09:17:58-05:00, 2009:11:05 09:18:40-05:00, 2009:11:05 09:36:59-05:00, 2009:11:05 09:50:08-05:00, 2009:11:05 10:51:40-05:00, 2009:11:05 11:12:09-05:00, 2009:11:05 11:20:01-05:00, 2009:11:05 11:49:32-05:00, 2009:11:05 11:57:49-05:00, 2009:11:05 12:58:38-05:00, 2009:11:05 13:02:01-05:00, 2009:11:05 13:29:49-05:00, 2009:11:05 13:50:55-05:00, 2009:11:05 13:59:47-05:00, 2009:11:05 14:33:49-05:00, 2009:11:05 14:34:56-05:00, 2009:11:05 14:43:47-05:00, 2009:11:05 14:44:48-05:00, 2009:11:05 14:45:24-05:00, 2009:11:05 14:45:24-05:00, 2009:11:20 10:39:41-05:00, 2009:11:20 10:44:28-05:00, 2009:11:20 10:49:55-05:00, 2009:11:20 10:54:29-05:00, 2009:11:20 11:00:25-05:00, 2009:11:20 11:34:54-05:00, 2009:11:20 11:38:53-05:00, 2009:11:20 11:55:46-05:00, 2009:11:20 13:46:07-05:00, 2009:11:20 13:51:54-05:00, 2009:11:20 13:53:39-05:00, 2009:11:20 14:08:22-05:00, 2009:11:20 14:10-05:00, 2009:11:20 14:22:45-05:00, 2009:11:20 14:29:34-05:00, 2009:11:20 14:41:08-05:00, 2009:11:20 14:41:33-05:00, 2009:11:20 14:41:33-05:00, 2009:11:20 14:55:16-05:00, 2009:11:20 15:12:05-05:00, 2009:11:20 15:12:27-05:00, 2009:11:20 15:13:09-05:00, 2009:11:20 15:13:25-05:00, 2009:11:20 15:13:46-05:00, 2009:11:20 15:14:16-05:00, 2009:11:20 15:14:43-05:00, 2009:11:20 15:21:46-05:00, 2009:11:23 14:21:04-05:00, 2009:11:23 14:23:31-05:00, 2009:11:23 15:52-05:00, 2009:11:23 16:03:48-05:00, 2009:11:24 08:31:09-05:00, 2009:11:24 08:33:20-05:00, 2009:11:24 08:37:40-05:00, 2009:12:10 12:22:06-05:00, 2009:12:10 12:24:28-05:00, 2009:12:11 08:12:51-05:00, 2009:12:11 08:52:26-05:00, 2009:12:11 09:00:47-05:00, 2009:12:11 09:01:24-05:00, 2009:12:11 09:04:32-05:00, 2009:12:15 07:43:11-05:00, 2009:12:16 10:28:16-05:00
History Software Agent          : Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0, Adobe InDesign 6.0
History Changed                 : /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /metadata, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /, /
Derived From Instance ID        : xmp.iid:783F424E222068118263F6ECCA183DB0
Derived From Document ID        : xmp.did:EFA28EAD3F206811994CCFD1D5D7AC70
Derived From Original Document ID: xmp.did:058011740720681195FE9CE16554C163
Derived From Rendition Class    : default
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:9738D446161211DEA316AEE27941C01E, xmp.iid:F87F117407206811A70FA9CEE59E8137, xmp.iid:F87F117407206811A70FA9CEE59E8137, xmp.iid:F97F117407206811A70FA9CEE59E8137, xmp.iid:F87F117407206811A70FA9CEE59E8137, xmp.iid:F77F117407206811A70FA9CEE59E8137, xmp.iid:FA7F117407206811A70FA9CEE59E8137, xmp.iid:FC7F117407206811A70FA9CEE59E8137, xmp.iid:FB7F117407206811A70FA9CEE59E8137, xmp.iid:FE7F117407206811A70FA9CEE59E8137, xmp.iid:FD7F117407206811A70FA9CEE59E8137, xmp.iid:B6EE660E082068118DBB8E52C104DA15, xmp.iid:02801174072068118F62EB1F0298675B, uuid:5E7393099DC3DE11AEFFD134334E4687, uuid:9738D446161211DEA316AEE27941C01E, uuid:655D5074AD9811DD8C4ED82D1DEED891, uuid:9104A47AAD9B11DD8C4ED82D1DEED891, uuid:9104A482AD9B11DD8C4ED82D1DEED891, uuid:655D5077AD9811DD8C4ED82D1DEED891, uuid:9104A47CAD9B11DD8C4ED82D1DEED891, uuid:9104A484AD9B11DD8C4ED82D1DEED891, uuid:655D507BAD9811DD8C4ED82D1DEED891, uuid:9104A480AD9B11DD8C4ED82D1DEED891, uuid:E4099C5FADA011DD8C4ED82D1DEED891, uuid:655D5079AD9811DD8C4ED82D1DEED891, uuid:9104A47EAD9B11DD8C4ED82D1DEED891, uuid:E4099C5DADA011DD8C4ED82D1DEED891, uuid:E4099C61ADA011DD8C4ED82D1DEED891
Manifest Reference Document ID  : uuid:9738D445161211DEA316AEE27941C01E, xmp.did:F87F117407206811A70FA9CEE59E8137, xmp.did:F87F117407206811A70FA9CEE59E8137, xmp.did:F97F117407206811A70FA9CEE59E8137, xmp.did:F87F117407206811A70FA9CEE59E8137, xmp.did:F77F117407206811A70FA9CEE59E8137, xmp.did:FA7F117407206811A70FA9CEE59E8137, xmp.did:FC7F117407206811A70FA9CEE59E8137, xmp.did:FB7F117407206811A70FA9CEE59E8137, xmp.did:FE7F117407206811A70FA9CEE59E8137, xmp.did:FD7F117407206811A70FA9CEE59E8137, xmp.did:B6EE660E082068118DBB8E52C104DA15, xmp.did:01801174072068118F62EB1F0298675B, uuid:5D7393099DC3DE11AEFFD134334E4687, uuid:9738D445161211DEA316AEE27941C01E, uuid:83CB51C4AD7211DD8C4ED82D1DEED891, uuid:655D507CAD9811DD8C4ED82D1DEED891, uuid:9104A481AD9B11DD8C4ED82D1DEED891, uuid:655D5075AD9811DD8C4ED82D1DEED891, uuid:9104A47BAD9B11DD8C4ED82D1DEED891, uuid:9104A483AD9B11DD8C4ED82D1DEED891, uuid:655D507AAD9811DD8C4ED82D1DEED891, uuid:9104A47FAD9B11DD8C4ED82D1DEED891, uuid:E4099C5EADA011DD8C4ED82D1DEED891, uuid:655D5078AD9811DD8C4ED82D1DEED891, uuid:9104A47DAD9B11DD8C4ED82D1DEED891, uuid:E4099C5CADA011DD8C4ED82D1DEED891, uuid:E4099C60ADA011DD8C4ED82D1DEED891
Doc Change Count                : 6836
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.0
Trapped                         : False
Page Count                      : 16
Creator                         : Adobe InDesign CS4 (6.0.4)

EXIF Metadata provided by EXIF.tools