Audiovox Vx7010 Installation Manual
Jensen-Vx-7010-Installation-Guide-775671 jensen-vx-7010-installation-guide-775671
VX-7010 - Installation Guide VX7010_IM_EN Free User Guide for Jensen GPS, Manual
2015-05-27
: Audiovox Audiovox-Vx7010-Installation-Manual-725218 audiovox-vx7010-installation-manual-725218 audiovox pdf
Open the PDF directly: View PDF .
Page Count: 6
Download | |
Open PDF In Browser | View PDF |
VX7010 DVD / NAV / SiriusXM-Ready®/ Built-in Bluetooth / Pandora Link Compatible with iPhone /Compatible with iPod / USB / Aux In INSTALLATION GUIDE What’s in the Box The following items are supplied with the VX7010: • • • • • • • • • VX7010 Head Unit Trim Ring Hardware Bag Power/Speaker Output Harness Remote Control External Microphone GPS Antenna Owners Manual & Warranty Card Installation Guide Tools and Supplies The following tools and supplies are needed to install the VX7020: • Torx type, flat-head and Philips screwdrivers • Wire cutters and strippers • Tools to remove existing radio (screw driver, socket wrench set or other tools) • Electrical tape • Crimping tool • Volt meter/test light • Crimp connections • 18 gauge wire for power connections • 16 – 18 gauge speaker wire WARNING! Never install this unit where operation and viewing could interfere with safe driving conditions. 128-9290 VX7010 Installation Guide 03-25-14.indd 1 3/25/2014 11:36:58 AM 128-9290 VX7010 Installation Guide 03-25-14.indd 2 3/25/2014 11:36:58 AM Optional Equipment • Steering Wheel Control (SWC)- The VX7010 is SWC ready for vehicles equipped with the option. See wiring diagram for installation details. For SWC programming details, please see the operation manual. • Rear Camera- The VX7010 is Rear Camera ready for vehicles equipped with the option. See wiring diagram for installation details. Disconnect the Battery • T o prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation. NOTE: If the VX7010 is to be installed in a car equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution during installation to avoid causing a short circuit. Replacing the Fuse • When replacing the vehicles Radio fuse always use the proper rated replacement fuse. Using a fuse with an improper rating could damage the unit and cause a fire. ISO-DIN Installation The VX7010 is designed to fit into a 1.0 DIN dashboard opening. The unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please consult with your local car stereo specialty shop for assistance on this type of installation. 1. Remove the existing factory radio from the dashboard or center console mounting. Save all hardware and brackets as Dash Board they will be used to mount the new radio. 2. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio. CAUTION! Do not exceed M5 X 6MM screw size. Longer screws may damage components inside the chassis. Rubber Sheath 3. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully and make certain all connections are secure and insulated with wire nuts or electrical tape. After completing the wiring connections, plug the ISO connectors into the mating sockets on the rear of the chassis. Turn the unit on to confirm operation (vehicle ignition switch must be “ON”). If the unit does not operate, re-check all wiring until the problem is corrected. 4. Mount the new radio assembly to the dashboard or center console using the reverse procedure in step 1 above. CAUTION! Be careful not to damage the car wiring. Mounting The rear of the unit Trim plate NOTE: It is the end-users responsibility to install and operate this unit in a manner in accordance with local, state and federal laws. The PARKING BRAKE wire MUST BE CONNECTED as directed in the manual. Using the Cosmetic Trim Ring A cosmetic trim ring is supplied with the head unit for installation flexibility. This unit will fit into most import dashes with little or no modification to the dash board/cavity. Some US domestic vehicle dashes will accept a Double-DIN chassis, but there is usually a small gap between the radio and dash piece after installation is complete. In this case, use the trim ring to conceal any gaps that may be present. NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 30° of horizontal. Make sure the unit is mounted within this limitation. 1 128-9290 VX7010 Installation Guide 03-25-14.indd 3 3/25/2014 11:36:59 AM Wiring Diagram CAUTION! IMPORTANT: Incorrect wiring connections can damage the unit. Follow the wiring instructions carefully, or have the installation handled by an experienced technician. Need Help? For technical assistance, call the Jensen customer support line at 1-800-323-4815. BLACK BLACK RADIO ANT SWC A White/Purple White/Purple SWC B White/Brown White/Brown SWC GND Brown/Black Brown/Black MIC BACKUP CAMERA BT ANTENNA BLACK MONITOR BACKUP CAMERA YELLOW PARK SWC Adapter Cable BRAKE INDICATION Black/SiriusXM BATTERY GND PARKING BRAKE SWITCH AUX2 R AUX2 L AUX2 VIDEO IN YELLOW POWER ANT & AMP.CONT REVERSE BLUE/WHITE GREEN/WHITE MOBILE POWER AMP The VX7010 has a built-in SWC Interface compatible with most resistive type OE steering wheel controls. In most installations, only two of the three wires will be needed to interface the OE steering wheel controls to the VX7010. SWC A - Primary SWC Wire SWC B - Secondary SWC Wire SWC Ground - Chassis ground Initial wiring of the SWC interface should include the SWC A and SWC Ground wire. If this combination of wiring does not support your vehicle functions, then try the SWC B and SWC Ground wire combination. Do not use only SWC A and SWC B. The SWC Ground must be connected. Some vehicles may not support all SWC functions. Professional Installation is recommended. VIDEO OUT BATTERY GND BATTERY(+) GND(-) IGNITION SWITCH ACC+ GND SIGNAL LIGHT REVERSE DRIVING GEAR Dimmer TFT ORANGE 2 128-9290 VX7010 Installation Guide 03-25-14.indd 4 3/25/2014 11:37:03 AM NOTES: 3 128-9290 VX7010 Installation Guide 03-25-14.indd 5 3/25/2014 11:37:03 AM Installation Guide Voxx Electronics Corporation Hauppauge, NY 11788 Technical Assistance: 1-800-323-4815 www.jensenmobile.com © 2014 Printed in China 128-9290 128-9290 VX7010 Installation Guide 03-25-14.indd 6 3/25/2014 11:37:04 AM
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27 Create Date : 2014:03:25 11:36:53-04:00 Metadata Date : 2014:03:25 11:37:05-04:00 Modify Date : 2014:03:25 11:37:05-04:00 Creator Tool : Adobe InDesign CS6 (Windows) Instance ID : uuid:7f0479e3-e105-4c47-9f72-b23e80586eda Original Document ID : xmp.did:5D8294035461E1118EFDFB8E6A14ED6A Document ID : xmp.id:3535C10533B4E311A261A6B8C5719074 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:B7E5F04C30B4E311A261A6B8C5719074 Derived From Document ID : xmp.did:B7E5F04C30B4E311A261A6B8C5719074 Derived From Original Document ID: xmp.did:5D8294035461E1118EFDFB8E6A14ED6A Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2014:03:25 11:36:53-04:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False Page Count : 6 Creator : Adobe InDesign CS6 (Windows)EXIF Metadata provided by EXIF.tools