Authentrend TECHNOLOGY ATKEYBLE1 Bluetooth Fingerprint Authenticator User Manual ATKEY BLE QSG EN CHT 20171228r1
Authentrend TECHNOLOGY INC. Bluetooth Fingerprint Authenticator ATKEY BLE QSG EN CHT 20171228r1
User Manual
FCC Label Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference
that may cause undesired operation.
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee
of this device could void the user‘s authority to operate the
equipment.
Exposure to Radio Frequency Radiation:
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. This transmitter must not be co-
located or operating in conjunction with any other antenna or
transmitter.
NCC警語:
本產品符合低功率電波射性電機管辦法 第條、第四條等條
規定
1. 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使
者均不得擅變頻率、加功率或變原設計之特性及功能。
2. 低功率射頻電機之使不得影響航安全及擾合法通信；經發現
有擾現象時，應立即停，並改善無擾時得繼續使。
前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機
須忍受合法通信或業、科學及醫療電波射性電機設備之擾。
AuthenTrend
Quick Start Guide
簡使冊
ATKey.BLE
Bluetooth Fingerprint Authenticator
牙指紋認證裝置
ATKEY.BLE is a wireless fingerprint
authenticator that adopts 2.4GHz
wireless technology of Bluetooth
Low Energy 4.0 to to prove to a PC
or mobile system that you really are
who you are via the verification of
enrolled fingerprints.
ATKEY.BLE內建先進的指紋辨識
以及低功耗牙通無線訊技術，主要
應於與綁定的個電腦或是動裝
置系統進可靠的份認證機制。
INSTALLATION:
1. Enable PIN of Windows 10 from
“Sign-In Option” of “Accounts” in
Windows Settings page.
2. Install ATKey app from Windows
Store.
安裝：
1. 透過系統設定中的”Sign-In Option”
啟並設定PIN碼。
2. 從Windows Store下載ATKey應
程式並執安裝。
1
2
GET STARTED:
1. Plug in USB cable to power up
ATKey.BLE (Blue LED appears).
2. Keep USB cable plugged to charge
ATKey.BLE (Red LED on) until it’s
fully charged (Red LED off).
啟動裝置：
1. 插上USB充電線將ATKey.BLE啟動
並開始運作（顯燈）。
2. 紅燈恆亮表ATKey.BLE正在進
充電，充電完成紅燈將會熄滅。
SYSTEM REQUIREMENTS:
-Windows 10 RS2 (Creators Update,
build 1703)
-ATKey app (download from Windows
Store: https://www.microsoft.com/store/
apps/9P7GR8W9SJD3)
系統要求：
-Windows 10 RS2 (Creators Update,
build 1703)
-ATKey 應程式 (下載徑: https://
www.microsoft.com/store/apps/
9P7GR8W9SJD3)
3
4
REGISTER DEVICE:
Run ATKey App to pair up and register
ATKey.BLE with your computer. Be
sure to touch the fingerprint sensing
area to confirm the pairing procedures
(Blue LED flashing).
綁定裝置：
1. 執ATKey應程式開始進芽配
對以及裝置註冊的程序。當
ATKey.BLE上出現閃爍燈，請觸
碰指紋感應區塊進綁定確認。
ENROLL FINGERPRINTS:
1. Following the instruction of ATKey
App and place your fingertip over
the sensing area as when flashing
Blue LED appears.
2. Repeating 8 to 10 times to
complete the fingerprint enrollment
procedures.
註冊指紋資料：
1. 遵從ATKey應程式的指進指紋
註冊的程序，當ATKey.BLE裝置上
出現閃爍燈時請將您希望註冊的
指紋碰觸感應區域。
2. 此動作需要重複八次完成註
冊的程序。
5
WINDOWS HELLO &
DYNAMIC LOCK:
1. Select to companion ATKey.BLE
with your computer to enable
Windows CDF service.
2. “Dynamic Lock” (your computer will
be automatically locked as when
the registered ATKey.BLE goes
away) can be enabled only if your
Windows 10 system is build 1703
or later version.
啟WINDOWS HELLO與動
鎖屏：
1. 請點選將ATKey.BLE設定為綁定電
腦的隨附裝置以享Windows Hello
功能。
2. 唯有當Windows 10作業系統版本等
於或於build 1703才能夠選動
鎖屏功能。