Authinx FWMD Indoor/Outdoor Motion Detector User Manual FWMD OM pmd

Download:
Mirror Download [FCC.gov]
Document ID	370151
Application ID	HdNl/TTk6ylE+Q3CQQh5bA==
Document Description	Exhibit D Users Manual per 2 1033 b3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	0.59kB (7364 bits)
Date Submitted	2003-10-31 00:00:00
Date Available	2003-10-31 00:00:00
Creation Date	2003-10-20 14:19:50
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2003-10-20 14:19:50
Document Title	FWMD-OM.pmd
Document Creator	PageMaker 7.0
Document Author:	drye

Set-Up and Operating Instructions for FWMD
Indoor/Outdoor Motion Detector
The FWMD Motion Detector sends Wireless Radio Frequency (RF) signals to a Black&Decker Messenger Hub FWMH). The Hub
then passes the signals onto your house wiring to turn on lights, appliances, or Freewire wireless cameras around your home. You
plug your lights and appliances into Freewire Modules (sold separately). You can set the Motion Detector to turn the lights or
cameras off after motion stops. You can set this for a preset time of 1, 2, 4, 8 minutes etc., (see below for more details). You can set the
unit to work at all times or only at night.
Installation: Remove the screw from the bottom of the FWMD Motion Detector. Remove the battery cover and install two AAA
alkaline batteries. Observe polarity. Leave the cover off for now. Plug in a Messenger Hub (FWMH, sold separately) and set it to
Housecode A, and Unit Code 1. Plug a lamp into a Freewire Lamp Receiver (sold separately) and set it to Housecode A and Unit Code
1. Plug the module into any AC outlet.
Synchronize the Motion Detector to work with the Hub: Set the Hub to Learn. Press the Synchronize button on the Motion Detector.
The green indicator on the Hub flashes. Set the Hub back to Run.
To test the Motion Detector: Press the Synchronize button once. The Motion Detector transmits the “device ON” RF signal and its
red light flashes. Press the Synchronize button once again. The Motion Detector transmits the “device OFF” RF signal and its red
light flashes. If you set a Hub and a Lamp Receiver to A1 they will both turn on and off when you repeatedly press the Synchronize
button on the Motion Detector.
Place the Motion Detector on a shelf or mount it on a wall at least 6 feet above the ground. Let it settle for a minute and then walk past
it. The lamp connected to any Lamp Receiver set to A1, or a camera set to A1 turns on. The light or camera turns off a short time later
as long as no motion has been detected. The default time is 1 minute but you can change this (see below for more details). You can
now screw the Motion Detector to a wall and replace the battery cover.
To change the Unit Code that the Motion Detector transmits:
Turn its dial to any number (1-16).
To change the delay after motion is detected before an OFF code is transmitted:
Turn the dial on the Motion Detector to the desired setting:
0 (no off code sent), 1 minute, 2 minutes, 4 minutes, 8 minutes, 16 minutes, 32 minutes, 64 minutes, 128 minutes. 256 minutes.
To change when the Motion Detector detects motion:
Set the switch inside the battery compartment to “24Hr” if you want the Motion detector to detect motion at all times. Set the switch
to “Night” if you only want it to detect motion when its dark (be sure to place the unit in a place where it can see if its dark outside,
and don’t place it near the light that it turns on when it detects motion.
Dusk/Dawn sensing:
If you set the “off delay” to 0 AND set the Motion Detector to only work when its dark, it will not detect any motion at all, but will
instead turn on a light when it gets dark and turn it off when it gets light. The light it controls it set by the position of its Unit Code
dial (1-16) and the setting of the Housecode dial on the Hub (A-P).
NOTES:
After replacing batteries, and after a transmission, you need to wait 30 seconds before the Motion Detector will see any motion.
The default time after which an OFF code is sent is 1 minute.
When the Motion Detector turns on a camera, other cameras in a group of 3 turn off, but you might not want the Motion Detector to
turn cameras off after motions stops, best to set the off delay to 0 minutes when using the Motion Detector with cameras.
If the Hub is set to Learn, and the Motion Detector sees motion, it will synchronize itself to the Hub, i.e. you won’t need to press its
Synchronize button to Synchronize it.
FCC CAUTION: THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TO THE UNITS. ANY CHANGES MADE TO THE UNITS WILL VOID THE
USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
FWMD-10/03

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Create Date                     : 2003:10:20 14:19:50-07:00
Modify Date                     : 2003:10:20 14:19:50-07:00
Page Count                      : 1
Creation Date                   : 2003:10:20 21:19:50Z
Mod Date                        : 2003:10:20 21:19:50Z
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : drye
Metadata Date                   : 2003:10:20 21:19:50Z
Creator                         : drye
Title                           : FWMD-OM.pmd

EXIF Metadata provided by EXIF.tools