Authinx GB10A Glass Break / Light Sensor User Manual GB10A inst pm6

Authinx Inc. Glass Break / Light Sensor GB10A inst pm6

manual

Installing the GB10A Sensor• Peel off the paper from the double sided tape on the backand attach the Sensor to the inside of a window.• Slide the battery compartment off and install two AAalkaline batteries, observing polarity.• Set the switch to 1 to make the unit more sensitive to thesound of breaking glass, or 2 for less sensitive (helpsprevent false alarms).Glass Break/Light Sensor, Model GB10A Set Up and Operating InstructionsX-10 (USA) Inc., 91 Ruckman Rd., Closter, NJ 07624. www.x10.comGB10A-8/99DRPress and hold the TEST button for 10 seconds. The LED flashesand then stays on. Press again, the LED blinks the currentHousecode setting (1 for A, 2 for B, etc.). Press the LED thenumber of times for the new Housecode setting. The LED thenblinks back the setting.Replacing batteriesOpen the battery compartment and replace the batteries withtwo AA alkaline batteries. After replacing the batteries, thefollowing steps are necessary to determine that the Console stillrecognizes the GB10A.• Place the Console’s slide switch to RUN2.• Press TEST on the GB10A. If the Console chimes, itrecognizes the GB10A and no further action is necessary.If the Console did not chime:Place the Console’s slide switch to INSTALL. Press TEST onthe GB10A. The Console beeps and logs in the GB10A to thenext available zone. To make sure the Console logs the GB10Aback into the same zone it was allocated to before you changedthe batteries, wait 4 hours after removing the old batteries beforereinstalling (until the zone indicator on the Console startsflashing).X-10 (USA) INC. LIMITED 1-YEAR WARRANTYX-10 (USA) Inc. warrants X-10 products to be free from defectivematerial and workmanship for a period of one (1) year from theoriginal date of purchase at retail. X-10 (USA) Inc. agrees torepair or replace, at it’s sole discretion, a defective X-10 productif returned to X-10 (USA) Inc. within the warranty period andwith proof of purchase.If service is required under this warranty:1. Return the defective unit postage prepaid to X-10 (USA)Inc. at the address below.2. Enclose a check for $4.00 to cover postage and handling.3. Enclose a dated proof of purchase.4. X-10 is not responsible for shipping damage.F.C.C. CAUTION - THIS DEVICE COMPLIES WITH PART 15 OFTHE FCC RULES. OPERATION IS SUBJECT TO THEFOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOTCAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICEMUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDINGINTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TOTHE UNITS. ANY CHANGES MADE TO THE UNITS WILL VOIDTHE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.Registering the GB10A Sensor with the SecurityConsole• Set the slide switch on the Security Console to INSTALL.• Press the TEST button on the GB10A Sensor. The consolebeeps once to confirm and the next available zone LEDlights.• Return the console slide switch to the RUN1 or RUN2position.Testing the GB10A Sensor• Set the slide switch on the Security Console to RUN2.• Press TEST on the GB10A. The console beeps to acknowl-edge and the zone LED lights.*Note: you can install a total of 16 zones in the Console. Thiscan be a combination of Door/Window Sensors, MotionDetectors, and Glass Break/Light Sensors. See your SecuritySystem Owner’s Manual for more information.OperationWhen the security system is armed, the sound of breaking glasswithin 20 feet of the GB10A will set off the alarm.Setting the Housecode for the GB10A SensorThe GB10A also turns on a light (connected to an X10 Module)when it gets dark and turns it off when it gets light. It always turnson Modules set to Unit Code 1, but you can change the Housecodethat it transmits:LightSensorGlassBreakSensorGlassBreakSensitivity1 = High, 2 = Low.

Navigation menu