Authinx KR32A SECURITY KEY FOB REMOTE User Manual KR32A OM pmd

Authinx Inc. SECURITY KEY FOB REMOTE KR32A OM pmd

USERS MANUAL

Initializing Keyfob RemotesPress and hold  the ARM button on the Keyfob remote for 3-4 secondsand then release it. This initializes the remote and picks a randomcode that is used when it is registered with the Console.The default PIN is 0000, you can change this later, but for now press 0000 on thekeypad (under the lid to the bottom left of the display). This clears the top line andshows * for each number entered.This takes you to the first level of the menu at step 1. This is the INSTALLATIONlevel.Now simply press any button on the Keyfob remote. The Console acknowledges thatit has been registered by beeping and displaying RMOT  1 SET.Repeat this for any other Keyfob Remotes you want to register.  The displayincrements to RMOT  2 SET, etc. as you install more remotes.Press Clear to back out of the menu. You are asked to confirm,  1. YES, 2 NO.Pressing 1 takes you back to the HOME CONTROL screen. Pressing 2 takes you upone level of menu.Registering the Keyfob Remote with the ConsolePress either of the Menu up/down buttons (under the lid to the bottom left of thedisplay). The display then shows ENTER PIN (Personal Identification Number) inthe top line.Arming the systemPressing ARM HOME on the Console arms all Door/Window Sensors instantly.Motion Detectors will not trip the system when it is armed in the ARM HOME mode.Pressing ARM AWAY arms with an exit delay and an entry delay, to give you time todisarm the system after you enter your home. These delays will be what you specifiedfor your ENTRY DELAY (30 second default) and EXIT DELAY (1 minute default).Pressing ARM on the Keyfob remote always arms in the AWAY mode. This arms allDoor/Window Sensors AND Motion Detectors, but arms instantly.Disarming the systemPressing DISARM on the Keyfob remote disarms the system instantly.To disarm from the Console: Enter your 4 digit  PIN (Personal IdentificationNumber) this will be 0000 unless you changed it.Entering the PIN clears the top line and shows * for each number entered.When you see INSTALL on the display. Press OK and the display looks like this:ENTER PIN12:00 am****12:00 am1. INSTALL1. INSTALLZONEARMED HOME12:00 am****12:00 amDISARMED12:00 amPanic Alarm: Pressing BOTH Panic buttons at the same time trips the alarm, evenif the system was not armed.If the unit is armed  it will disarm when the PIN is entered, and return to the timedisplay, with DISARMED in the top line.Then after a short delay the display reverts to HOME CONTROL mode.
Battery ReplacementProviding the batteries have not already failed, they can be replaced withfresh batteries without the need to reinstall the remote. After removing theold batteries fresh batteries must be fitted within 30 seconds to ensure thatthe security code is retained.Gently pry the 2 halves of the Keyfob remotes case apart and install twoCR2016 lithium batteries battery in the compartment (+ facing up). Press the2 halves of the cabinet back together.Once the batteries have been replaced, confirm that the remote is still loggedin by arming the system. If it does not arm, the code has been lost and youwill need to proceed as described below.If the batteries have failed completely, the security code will have been lost.You will need to reinstall the Keyfob remote following the instructions insidethis booklet.FCC StatementTHIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2)THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIREDOPERATION.NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TO THEUNITS.  ANY CHANGES MADE TO THE UNITS WILL VOID THEUSER'S AUTHORITY TO OPERATE THE EQUIPMENT.Please visit: http://www.x10.com/support for additional help and warrantyconditions.Security Keyfob RemoteModel KR32AThe X10 Supervised Security System Model DS8000 includes a Security Consolewith an automatic dialer that calls friends or relatives in the event of a break in. Abattery powered Radio Frequency (RF) Door/Window Sensors and battery poweredRF Motion Detector to trigger the alarm, and an RF Keyfob Remote Control forarming and disarming the system. All sensors and remotes incorporate random digitalsecurity coding.The system may be configured with any combination of the following items:• Up to 16* Wireless Keyfob Security Remotes with arm/disarm and panicfunctions, and buttons to control security lights in and around the home.• Up to 30* magnetic switch operated Wireless Door/Window Sensors.• Up to 30* Wireless PIR Motion Detectors.• Optional X10 Home Automation modules such as plug-in lamp and appliancemodules and wired-in replacement wall switches can be added to the system.The manual for the DS8000 system describes the full installation process for thesecurity system, and should be referred to as a supplement to this instruction booklet.*Note: Door/Window Sensors and Motion Detectors may be added in anycombination up to a total of 30, e.g. 15 Door/Window Sensors and 15 MotionDetectors, or any combination up to a total of 30 . There are also 2 hard wiredinputs, which are zones 31 and 32.X10 Wireless Technology, Inc. Kent WA 98032

Navigation menu