Authinx KR34A SLIM FIRE REMOTE MODULE User Manual KR34A IS pmd

Authinx Inc. SLIM FIRE REMOTE MODULE KR34A IS pmd

USERS MANUAL

.X10 Wireless Technology, Inc. LIMITED 1-YEAR WARRANTYX10.com, a division of X10 Wireless Technology, Inc. (X10) warrants X10 products to befree from defective material and workmanship for a period of one (1) year from the originaldate of purchase at retail. X10 agrees to repair or replace, at it’s sole discretion, a defectiveX10 product if returned to X10 within the warranty period and with proof of purchase.If service is required under this warranty:1. Call 1-800-675-3044 or visit www.x10.com, or e-mail sales@x10.com to obtain aReturn Merchandise Authorization (RMA) number.2. Return the defective unit postage prepaid to X10 (see address on back).3. Enclose a check for $4.00 to cover postage and handling.4. Enclose a dated proof of purchase.5. X10 is not responsible for shipping damage. Units to be returned should be packedcarefully.Please visit www.x10.com/warrantyto complete your on-line warranty registration. Thank you.For help or more information on setup, please visit: www.x10.com/supportKR34A SlimFire™ Remote installation and operating instructionsThe KR34A works with the RR501 (part of the RC5000) and the TM751 (part of the RC6500). It letsyou turn on and off two individually coded X-10 Modules and brighten and dim lights connected to LampModules and Wall Switch Modules. In the default state (after first fitting the battery) the KR34A is setto Housecode A. The first (top) two ON-OFF buttons control modules set to Unit Code 1. The second(middle) two buttons control A2.1. Plug in an X-10 Transceiver (RR501 or TM751, sold separately).2. To turn on or off X-10 Modules set to Unit Code 1 (on Housecode A) press the first (top) ONor OFF button. To turn on or off X-10 Modules set to Unit Code 2 (on Housecode A) press thesecond (bottom) ON or OFF button. To brighten or dim Lamp Modules or Wall Switch Modulespress the number button first, the press Bright or Dim button. If you want to control Modules 1and 2 on Housecode A, that's it. You don't need to read any further.To change the Housecode•Press and hold the first (top) ON button. The red LED blinks once. 3 seconds later, the LEDblinks the current setting: 1 blink for Housecode A, 2 blinks for B..... 16 blinks for P.•Release the first (top) ON button.•Press and release the first (top) ON button the appropriate number of times for the Housecodeyou want to set. Once for A, twice for B, etc. The LED blinks for each press. IMPORTANT:Hold the button on your last press. 3 seconds later, the red LED blinks back the new setting, e.g.3 blinks for Housecode C. If you do not follow this programming sequence, the LED will stayon for 1 second and your existing setting will not be changed.To change the Unit Code for the first (top) two buttons (the second pair of buttons are always one# higher than the first pair, i.e. if you set the first button to 6, the second button controls 7, etc.).•Press and hold the top OFF button. The red LED blinks once. 3 seconds later, the LED blinksthe current setting: 1 blink for Unit Code 1, 2 blinks for 2, 16 blinks for 16.•Release the top OFF button.•Press and release the top OFF button the appropriate number of times for the Unit Code youwant. IMPORTANT: Hold the button on your last press. 3 seconds later new code blinks back.If you do not follow this programming sequence, the LED will stay on for 1 second and yourexisting setting will not be changed.To change the battery: Pry the unit apart and fit a CR2025 Lithium 3V battery. Observe polarity.F.C.C. CAUTION - THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATIONIS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSEHARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCERECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TO THE UNITS. ANY CHANGESMADE TO THE UNITS WILL VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. KR34A-12/05Press to turnA1 ON.After pressing anumber, press andhold to Brighten.After pressing anumber, press andhold to Dim.Press to turnA2 ON.Press to turnA1 OFF.Press to turnA2 OFF.

Navigation menu