Authinx SS13A RF Wall Switch User Manual SS13A ins pm6

Authinx Inc. RF Wall Switch SS13A ins pm6

manual

X10 (USA) INC. LIMITED 1-YEAR WARRANTYX10 (USA) Inc. warrants X10 products to be free from defective material and workmanshipfor a period of one (1) year from the original date of purchase at retail. X10 (USA) Inc. agreesto repair or replace, at it’s sole discretion, a defective X10 product if returned to X10 (USA)Inc. within the warranty period and with proof of purchase.If service is required under this warranty:1. Return the defective unit postage prepaid to X10 (USA) Inc. (see address on back).2. Enclose a check for $4.00 to cover postage and handling.3. Enclose a dated proof of purchase.4. X10 is not responsible for shipping damage.Units to be returned should be packed carefully.5. For additional warranty information, contact X10 (USA) Inc.Your Name ....................................................................................................................Address ..................................................................................................................................................................................................................................................................Date Purchased .................. 19....... Store where purchased ............................................Stick-A-Switch™ (Model SS13A) Installation and operating instructionsThe SS13A works with the RR501 (part of the RC5000) and the TM751 (part of the RC6500). It letsyou turn on and off three individually coded X10 Modules and brighten and dim lights connected toLamp Modules and Wall Switch Modules. In the default state (after first fitting the battery) the SS13Ais set to Housecode A. The top three ON-OFF rocker keys control modules set to Unit Codes 1, 2, 3.The bottom rocker key brightens and dims lights connected to Lamp and Wall Switch Modules.1. Plug in an X10 Transceiver (RR501 or TM751, sold separately).2. To turn on or off X10 Modules set to Unit Codes 1, 2, or 3 (on Housecode A) press the left or rightside of the first, second or third rocker key. To brighten or dim Lamp Modules or Wall SwitchModules press the number button first, then press and hold the left or right side of the bottomrocker key. Attach the SS13A to a wall using double sided tape or Velcro.™ If you want to controlModules 1, 2 and 3 on Housecode A, that's it. You don't need to read any further.To change the Housecode•Press and hold the first (top) ON rocker key. The red LED blinks once. 3 seconds later, the LEDblinks the current setting: 1 blink for Housecode A, 2 blinks for B..... 16 blinks for P.•Release the first (top) ON rocker key.•Press and release the first (top) ON rocker key the appropriate number of times for the HouseCode you want to set. Once for A, twice for B, etc. The LED blinks for each press.IMPORTANT: Hold the button on your last press. 3 seconds later, the red LED blinks back thenew setting, e.g. 3 blinks for Housecode C. If you do not follow this programming sequence,the LED will stay on for 1 second and your existing setting will not be changed.To change the Unit Code for the first (top) rocker key (the second and third rockers are alwaysone # higher than the first). i.e. if you set the first rocker key to 6, the second rocker key controls7, and the third control 8, etc..•Press and hold the top OFF rocker key . The red LED blinks once. 3 seconds later, the LEDblinks the current setting: 1 blink for Unit Code 1, 2 blinks for 2, 16 blinks for 16.•Release the top OFF rocker key.•Press and release the top OFF rocker key the appropriate number of times for the Unit Codeyou want. IMPORTANT: Hold the key on your last press. 3 seconds later the new code blinksback. If you do not follow this programming sequence, the LED will stay on for 1 second andyour existing setting will not be changed.To change battery: open battery holder and fit a CR2032 Lithium 3V battery. Observe polarity.F.C.C. CAUTION - THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATIONIS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSEHARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCERECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.NOTE: NO CHANGES OR MODIFICATIONS MAY BE MADE TO THE UNITS. ANY CHANGESMADE TO THE UNITS WILL VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT. SS13A-5/99Press left side to turn on, right sideto turn off modules set to UnitCodes 1, 2, and 3 on Housecode A(the default setting).Then press and hold left side tobrighten or right side to dim.Replace battery with CR2032, 3Vlithium type.

Navigation menu