Automatic Technology WL100V2 WIRELESS WLOCK-03 TRANSCEIVER User Manual
Automatic Technology (Australia) Pty. Ltd. WIRELESS WLOCK-03 TRANSCEIVER
User Manual
Auto-Lock Kit Garage Door Lock Installation Instructions Standard Installation Limited Sideroom Installation GARAGE DOOR LOCK - ORDER NO. MC-0002 ITEM DESCRIPTION GARAGE DOOR LOCK - ORDER NO. MC-0002 QTY ITEM DESCRIPTION QTY GARAGE DOOR LOCK GARAGE DOOR LOCK BATTERY C-LR14 MOUNTING PLATE BRACKET STRIKER GDL100 WIRELESS WBS-1V1 AY BATTERY C-LR14 WBS HARNESS 90MM AY WBS HARNESS 400MM AY WIRELESS WBS-1V1 AY TAPTITE SCREW “P” WBS HARNESS 90MM AY VELCRO 20 X 50 WBS HARNESS 400MM AY TAPTITE SCREW “P” VELCRO 20 X 50 WIRELESS WBS-1V1 KIT 1 ORDER 14827 MOUNTING SCREW PACK GDL100 ORDER 61411 14 BUTTON HEAD SCREW ZN M6 X 14 WIRELESS WBS-1V1 KIT 1 ORDER 14827 MOUNTING SCREW PACK GDL100 ORDER 61411 QR Code To view step by step installation guide video, download a QR Code Reader App from your App Store and scan this code. 10 BOLT 1/4” - 20TPI - UNCX1/2” SQ NECK 11 NUT SER FLNG 1/4” X 20-TP1 UNC ZN 12 SCREW TEK 14G-20X25 FLNG HD CL4 13 CROSS RECESSED SCREW M6X12 This device will slide a bolt into the guide track automatically when the door is closed. Not suitable for garages that have only one exit. For emergency release press the emergency unlock button on the lock. This will disengage the lock from the guide track and allow you to disengage the opener and open the door. The lock will re-engage after the next complete cycle. It is our strong recommendation that your opener be fitted with SAFETY BEAMS. Safety Beams detect any obstructions in the door/gate’s path and override automatic operation if one presents. NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Doc # 160070_01 Part # 79171 Released 30/06/17 ata 2 Auto-Lock Installation Instructions Important Safety Instructions WARNING! • • • DO NOT attempt to disassemble, repair or modify the product. This will invalidate the warranty. Do not allow children to play with the Auto-Lock. Not suitable for garages that have only one exit. CAUTION: Fall from ladder Burns • • • • • Ensure ladder is the correct type for job. Ensure ladder is on flat ground. Ensure user has 3 points of contact while on ladder. DO NOT handle damaged or leaking batteries The Auto-Lock Kit contains sealed lead-acid batteries that must be disposed of properly at the end of their useful life. Preparation Fail Safe - When the battery within the Auto-Lock is running low the operator will flash three times at each cycle and it will keep the lock in the open position until the batteries are replaced. This will ensure that the Auto-Lock will not remain locked when the batteries run out. Fail Secure - When a power failure occurs the Auto-Lock will remain in the state it is in when the power failure occurs. Therefore the power interuption does not interfere with the status of the Auto-Lock. If battery backup is installed the Auto-Lock will operate as per normal. IMPORTANT WARNING: • DO NOT attempt to disassemble, repair or modify the product. This will invalidate the warranty. • DO NOT allow children to play with the Auto-Lock. • Not suitable for garages that have only one exit. • DO NOT cover, paint or lubricate the product. Preparation - pull tab a. Prior to installation of the Auto-lock, pull to remove the battery isolation tab. b. Once removed the battery will engage and the lock is operational. Examine the garage and proceed to either Standard or Limited Sideroom Installation. ata Auto-Lock Installation Instructions Standard Installation Preparation - mounting on track a. Close the door. b. Using a marker pen, mark the position of the top of the second door wheel from the floor on the track. c. Open the door and transfer this mark to the inside of the track. d. Remove the drilling template label. e. Place the Datum line on the template on top of the line marked inside the track. f. Drill holes in the track using 15/64 in (6mm) and 15/32 in (12mm) drill bits. g. Affix garage door lock 1 using two (2) M6 x 14 button head screws 14 . h. Close the door and check the position of the lock to the wheel. Proceed to Connecting Wireless Basestation to operator. 14 Limited Sideroom Installation Preparation - mounting on door stile a. Close the door. b. Fit the mounting plate 2 to the garage door lock 1 using two (2) M6 x 12 cross recessed screws 13 . c. Determine mounting position of: i. the bracket striker 3 , ensuring it aligns with slots in the track (as shown). ii. the garage door lock 1 with mounting plate, on the top of the bottom panel of the door stile, iii. mark both positions and make sure the lock bolt engages fully into the bracket striker 3 . d. Open door and affix the striker bracket 3 to the track, where marked, with 3 x Bolts 10 and nuts 11 . e. Close the door. f. Place the lock with mounting plate onto position previously marked. g. Align the lock 1 with the bracket striker 3 and make sure the lock bolt engages fully into the bracket striker. h. Affix the lock mounting plate to the door with four (4) Tek screws 12 . 13 12 10 11 ata Connect Wireless Basestation to Opener AM-808 and AM-888 Preparation of Opener a. Disconnect the power supply to the opener. b. Remove the back cover via screw at top. c. To connect the harness remove the side flap from the side of cover. Slide the WBS harness 3 1/2 inches 6 through the slot in the cover. Connect the harness to the 4 pin connector on the control board as shown on the control board. d. Refit the covers. Mount and connect Transceiver a. Plug the other end of the harness into the wireless basestation 5 . b. Connect the wireless basestation to opener by sliding the aerial from the wireless basestation 5 through the slot in the cover as shown so that aerial hangs out of cover. Affix wireless basestation to opener with 1 x Taptite screw 8 . 4 Pin Connector Back cover screw Not available with AM-800 WARNING! DO NOT drill into the chassis or covers. A predrilled hole exists to secure the wireless basestation. Test the Opener a. Reconnect power to the opener and test operation. b. Upon completion of a full cycle the lock will engage into the track. Aerial slot Affix with screw here This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. ata Automatic Technology America VIneyard Centre II, 1452 Hughes Road, Grapevine, Texas 76051, United States of America P: +1 817 873 5076 W: www.automatictechnology.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : No Producer : CutePDF Editor (editor.CutePDF.com) Subject : Create Date : 2017:07:02 19:45:58-04:00 Author : Modify Date : 2017:07:02 19:45:58-04:00 Creator : Adobe InDesign CC 2017 (Windows) Title : Creator Version : 13 Container Version : 11 For : Nikolai Klepikov, Bounding Box : 0 0 630 810 Page Count : 4 Image Height : 810 Image Width : 630 Image Size : 630x810 Megapixels : 0.510EXIF Metadata provided by EXIF.tools