Automotive Distance Control Systems ARS100-2 Vehicle Radar System User Manual 54702195 eps
Automotive Distance Control Systems GmbH Vehicle Radar System 54702195 eps
Mercedes Benz Users Manual
Überblick über Displayanzeigen im Kombiinstrument. Die Beschreibung des Systems folgt auf der nächsten Seite. part2_01.fm Seite 133 Montag, 7. Mai 2001 7:06 07 Distronic (DTR) 1 Distronic is deactivated. The actual distance (5) and the should-be distance (6) to the vehicle ahead (4) are displayed. 2 Activating Distronic. The display with the selected speed is shown for approximately 5 seconds. 3 Distronic is activated. The message “DTR OFF” appears for approximately 5 seconds when Distronic is being deactivated. 4 Vehicle ahead. Only appears if a vehicle is detected ahead. 5 Actual distance to vehicle ahead. 6 Should-be distance to vehicle ahead (as calculated by Distronic). 7 Own vehicle. 8 Distance warning function is activated, see page 271. Press the è or ÿ button repeatedly until the required system is displayed. Distronic (DTR) see page 260. Pressing the è or ÿ button displays the next or previous system. Multifunction steering wheel, multifunction display Instruments and controls Operation Driving 133 Instrument cluster display Practical hints Car care Technical data Index part3_01.fm Seite 260 Montag, 7. Mai 2001 7:05 07 Instruments and controls Operation Driving Instrument cluster display Driving systems Distronic (DTR) (optional) When activated the Distronic system increases driving convenience, for example over long distances, as it automatically maintains a speed set by the driver by actively regulating the throttle setting. It also maintains within certain limitations a preset distance to a vehicle ahead. With Distronic switched off, the multifunction display continues to show the distance to the vehicle ahead, if so selected, see page 274. The distance warning function can be activated separately, see page 271. In Distronic mode, if the distance sensor detects a slower moving vehicle directly ahead, your vehicle speed will be reduced to the extent permitted by reduced throttle and up to 20% of vehicle braking power, so that you follow that vehicle at a preset distance, see page 272. Maximum range of detection is approximately 500 ft. (150 m). Practical hints Car care Technical data 260 Any given speed between 25 mph (Canada: 30 km/h) and 110 mph (Canada: 180 km/h) can be maintained with the Distronic by operating the control lever on the steering column. Warning! Distronic is a convenience system, its speed adjustment reduction capability is intended to make cruise control more effective and usable when traffic speeds vary. It is not, however, intended to nor does it replace the need for extreme care. The responsibility for the vehicle speed and the distance to the vehicle ahead, including most importantly brake operation to assure safe stopping distance, rests always with the driver. Warning! Distronic requires familiarity with its operational characteristics. We strongly recommend that you review the following information carefully before operating the system. Index part3_01.fm Seite 261 Montag, 7. Mai 2001 7:05 07 Note: Warning! For operation in the USA only: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: Only use Distronic if the traffic and weather conditions make it advisable to travel at a steady speed. (1) This device may not cause harmful interference, and Use of Distronic can be dangerous on winding roads or in heavy traffic because conditions do not allow safe driving at a steady speed. (2) this device must accept any interference received, including interference that may cause undesired operation. Use of Distronic can be dangerous on slippery roads. Rapid changes in tire adhesion can result in wheel spin and loss of control. Any unauthorized modification to this device could void the user’s authority to operate the equipment. Distronic does not act upon adverse sight distance conditions. Do not use Distronic during conditions of fog and heavy rain, snow or sleet. The “Resume” function should only be operated if the driver is fully aware of the previously set speed and wishes to resume this particular preset speed. Distronic does not recognize accordingly and will not react to stationary objects. It is designed and intended only to maintain a set speed and keep a set distance from moving objects in front of it. Driving systems Instruments and controls 261 Operation Driving Instrument cluster display Practical hints Car care Technical data Index part3_01.fm Seite 262 Montag, 7. Mai 2001 7:05 07 Instruments and controls Operation Driving Instrument cluster display Driving systems Practical hints Car care Technical data 262 3 Canceling To cancel Distronic, briefly push lever to position 3. The last set speed remains stored in memory. 4 Resume The speed stored in memory is displayed in the multifunction display, and one or two segments around the stored speed light up in the speedometer dial, see page 275. 1 Accelerate and set: To increase the speed by 5 mph (Canada: 10 km/h) – briefly lift lever up. 2 Decelerate and set: To reduce the speed by 5 mph (Canada: 10 km/h) – briefly depress lever. • If the lever is briefly pulled to position 4 when driving at a speed above approximately 25 mph (Canada: 30 km/h), the vehicle resumes the speed which was selected prior to the cancellation of Distronic. • For minor increases of speeds in increments of 1 mph (Canada: 1 km/h) – briefly pull lever to position 4. The last memorized speed is canceled when the electronic key in the starter switch is turned to position 1 or 0. Index part3_01.fm Seite 263 Montag, 7. Mai 2001 7:05 07 • Speed is set by briefly moving the control lever to position 1 or 2. Activation of Distronic The stored speed is displayed in the multifunction display for approximately 5 seconds (see also page 274), and one or two segments around the stored speed light up on the speedometer dial (see also page 275). • Remove foot from the accelerator. • When briefly lifting the control lever to position 1, the vehicle speed will increase in increments of 5 mph (Canada: 10 km/h). The stored speed is displayed in the multifunction display for approximately 5 seconds (see also page 274), and one or two segments around the stored speed light up on the speedometer dial (see also page 275). Any given speed above approximately 25 mph (Canada: 30 km/h) can be maintained: • Normally the vehicle is accelerated to the desired speed with the accelerator. • When briefly lowering the control lever to position 2, the vehicle speed will decrease in increments of 5 mph (Canada: 10 km/h). The stored speed is displayed in the multifunction display for approximately 5 seconds (see also page 274), and one or two segments around the stored speed light up on the speedometer dial (see also page 275). Driving systems Instruments and controls 263 Operation Driving Instrument cluster display Practical hints Car care Technical data Index part3_01.fm Seite 264 Montag, 7. Mai 2001 7:05 07 Instruments and controls Operation Driving Instrument cluster display Driving systems • For a more precise setting the speed can be increased in increments of 1 mph (Canada: 1 km/h) by briefly pulling the control lever in direction (4). Caution! If the driver’s foot is not fully removed from the accelerator pedal, the message “DISTRONIC OVERRIDE” appears in the multifunction display. The Distronic control system will be overridden and it will not regulate the preset vehicle speed and following distance. The vehicle speed and following distance will be determined only by the accelerator pedal position. Warning! Distronic brakes (up to 20% of vehicle braking power) the vehicle to restore the preset distance or to maintain the speed. The brake pedal is automatically retracted as this happens. Keep driver’s foot area clear at all times, including the area under the brake pedal. Objects stored in this area may impair pedal movement which could interfere with the braking ability of the Distronic system. Do not place your foot under the brake pedal – your foot could become caught. Practical hints Car care Technical data 264 Invalid attempts to activate The multifunction display will show “––– MPH” during invalid attempts to activate Distronic: • below a speed of approximately 25 mph (Canada: 30 km/h), • while the electronic stability program (ESP) is switched off – ESP warning lamp v in speedometer dial is illuminated, see page 112, • by moving the distronic control lever in “RESUME” direction (4) when no speed is stored in memory, • during the initialization and self-test phase after the engine is started – this can take up to 2 minutes, • while depressing the service brake pedal, • while the parking brake is set – check ; warning lamp (Canada: !) in instrument cluster, see page 112, • with the gear selector lever in position “P”, “R” or “N” – check gear range indicator display in instrument cluster, see page 112. See page 330 for malfunction and warning messages if the Distronic is malfunctioning. Index part3_01.fm Seite 265 Montag, 7. Mai 2001 7:05 07 Deactivation of Distronic • the gear selector lever is moved to position “N”, Briefly move the distronic control lever in “OFF” direction (3) – the stored speed remains in the memory until the electronic key in the starter switch is turned to position 1 or 0. • the electronic stability program (ESP) is active, • the electronic stability program (ESP) is switched off manually. Distronic is also deactivated if: Note: • the service brake pedal is depressed, A signal sounds and the message “DISTRONIC OFF” appears for 5 seconds in the multifunction display everytime Distronic is deactivated (except when moving distronic control lever in “OFF” direction). • the parking brake is activated, • the vehicle decelerates to less than approximately 25 mph (Canada: 30 km/h), e.g. while maintaining the distance to the vehicle ahead, Warning! The Distronic switches off and releases the brakes when the vehicle decelerates below the minimum speed of 25 mph (Canada: 30 km/h) by operation of the system. At that time, the driver must apply the brakes in order to reduce vehicle speed further or bring it to a stop. Driving systems Instruments and controls 265 Operation Driving Instrument cluster display Practical hints Car care Technical data Index part3_01.fm Seite 266 Montag, 7. Mai 2001 7:05 07 Instruments and controls Operation Driving Instrument cluster display Driving systems Driving with Distronic activated Practical hints Car care Technical data 266 from the speed of the vehicle in front up to your vehicle’s selected speed. See also page 274 for notes on the multifunction displays. Warning! Distronic brakes (up to 20% of vehicle braking power) the vehicle to restore the preset distance or to maintain the speed. The brake pedal is automatically retracted as this happens. Keep driver’s foot area clear at all times, including the area under the brake pedal. Objects stored in this area may impair pedal movement which could interfere with the braking ability of the Distronic system. With the electronic key in starter switch position 2, the distance warning lamp l in the speedometer dial comes on and goes out with the engine running. If the distance sensor detects a slower vehicle moving in front, your vehicle speed will be reduced by deceleration and braking of up to 20% of the vehicle braking capacity, so that you follow the vehicle ahead at the preset distance, see page 272. Segments in the speedometer illuminate to indicate the speed range Do not place your foot under the brake pedal – your foot could become caught. Index part3_01.fm Seite 267 Montag, 7. Mai 2001 7:05 07 Warning! Caution! An intermittent warning sounds and the distance warning lamp in the speedometer dial is illuminated if the Distronic system calculates that the distance to the vehicle ahead and your vehicle’s current speed indicate that Distronic will not be capable of slowing the vehicle sufficiently to maintain the preset following distance, which creates a danger of a collision. If the driver’s foot is not fully removed from the accelerator pedal, the message “DISTRONIC OVERRIDE” appears in the multifunction display. The Distronic control system will be overridden and it will not regulate the preset vehicle speed and following distance. The vehicle speed and following distance is determined only by the accelerator pedal position. Distronic works on steep uphill and downhill gradients by downshifting gears and applying the brakes to maintain the speed selected by the driver. The transmission will upshift again once the gradient evens out. Immediately brake the vehicle to increase the distance to the vehicle in front of you. The warning sound is intended as a final caution that you have not interceded with your own braking inputs to avoid a potentially dangerous situation. Do not wait for the operation of the warning signal to intercede with your own braking as that will result in potentially dangerous emergency braking which will not always result an impact being avoided. The speed can be increased (e.g. for passing) by using the accelerator. After the accelerator is released, the previously set speed will be resumed automatically. Distronic is deactivated if a vehicle in front causes your vehicle to slow down to less than approximately 25 mph (Canada: 30 km/h). A signal sounds and the message “DISTRONIC OFF” appears for 5 seconds in the multifunction display. Tailgating increases the risk of an accident. The distance warning sound continues until the driver activates the brake pedal, or the preset distance is obtained. As soon as the preset distance is obtained, the distance warning lamp goes out. Driving systems Instruments and controls The vehicle speed displayed can briefly vary from the speed setting of the Distronic system. 267 Operation Driving Instrument cluster display Practical hints Car care Technical data Index part3_01.fm Seite 268 Montag, 7. Mai 2001 7:05 07 Instruments and controls Operation Driving Instrument cluster display Driving systems Additional driving hints Warning! Distronic works to maintain the speed selected by the driver unless a moving obstacle proceeding directly ahead of it in the same travel direction is detected (e.g. following another vehicle ahead at a distance set by Distronic). This means that: • your vehicle can pass another vehicle after you change lanes, • while in a sharp turn or if the vehicle in front is in a sharp turn, Distronic could lose sight of a vehicle traveling in front of it, then your vehicle could accelerate to the previously selected speed. Distronic regulates only the distance between your vehicle and those directly ahead, but does not register stationary objects in the roadway, e.g.: Practical hints Car care Technical data 268 The driver must always be on the alert and observe all traffic and intercede with steering and braking inputs as necessary. Important! When starting the engine, Distronic goes through an initialization and self-test phase – this can take up to 2 minutes. The most likely cause for a malfunctioning system is caused by a dirty sensor (located behind the hood grille), especially at times of snow and ice or heavy rain. In such a case, Distronic will switch off, and the message “DISTRONIC – CLEAN SENSOR!” appears in the multifunction display. Warning! Distronic should not be used in snowy or icy road conditions. • a stopped vehicle in a traffic jam, • a disabled vehicle, • an oncoming vehicle. For cleaning and care of the Distronic sensor, see page 385. Restart the engine after cleaning the sensor. The following are some sample situations which may influence the functions of Distronic. Index part3_01.fm Seite 269 Montag, 7. Mai 2001 7:05 07 The Distronic system’s detection zone is relatively narrow at the start and becomes broader as it senses further from the vehicle. Thus, Distronic may not recognize another vehicle coming into your path close to the front of your vehicle. You must be prepared to intercede with braking or steering as necessary. A vehicle not traveling directly in front of you could cause detection problems, the actual distance to that vehicle really being much shorter. Traveling through turns or bends in the roadway may result in Distronic detecting a moving vehicle traveling in front but not in your lane of travel, causing your vehicle to brake late or unexpectedly. You must be prepared to intercede with accelerator or brake application as necessary. Driving systems Instruments and controls 269 Operation Driving Instrument cluster display Practical hints Car care Technical data Index part3_01.fm Seite 270 Montag, 7. Mai 2001 7:05 07 Instruments and controls Operation Driving Instrument cluster display Driving systems Practical hints Car care Technical data 270 P54.70-2164-26 A vehicle changing lanes at close range is only recognized when entering the area scanned by Distronic. You must apply the service brakes to gain sufficient distance to the vehicle ahead. A narrow vehicle (e.g. a motorcycle) is only recognized when entering the area scanned by Distronic. You must apply the service brakes to gain sufficient distance to the vehicle ahead. Index part3_01.fm Seite 271 Montag, 7. Mai 2001 7:05 07 Distance warning function Important! Even if Distronic is deactivated, the distance to the vehicle ahead continues to be measured, see page 274 for multifunction display. With the Distronic switched off, only the distance warning function operates, meaning the vehicle does not slow down. The Distronic lamp in the speedometer dial illuminates to advise the driver of a situation which under normal braking conditions and dry surfaces should have been addressed by the driver. Distronic does not register oncoming vehicles. Therefore there is no distance warning. The distance warning function can be activated separately, see page 271. It operates when driving at speeds above approximately 25 mph (Canada: 30 km/h). If the distance warning lamp in the speedometer dial lights up while driving and an intermittent warning sounds, immediate attention on the part of the driver is required. When recognizing a stationary obstacle or a slower vehicle moving in the vehicle’s path and the danger of a collision exists, the distance warning lamp in the speedometer dial lights up and simultaneously an intermittent warning sounds. As required by the traffic situation, apply the service brakes and navigate around a possible obstacle. However, do not drive by relying on the distance warning function as that will result in an emergency braking application which, especially depending on road surface conditions and driver reaction, will not always be able to avoid a collision. Warning! When pressing the brake pedal, the warning sound stops. The warning sound also stops, when the distance to the vehicle ahead is sufficient again without applying the brake pedal. In this case the distance warning lamp also extinguishes Driving systems Instruments and controls Important! Complex driving situations are not always fully recognized by Distronic, which could result in wrong or missing distance warnings. See page 268 for additional driving hints. 271 Operation Driving Instrument cluster display Practical hints Car care Technical data Index part3_01.fm Seite 272 Montag, 7. Mai 2001 7:05 07 Instruments and controls Operation Driving Instrument cluster display Driving systems Distronic settings Practical hints Car care Technical data 272 • Decrease distance – turn thumbwheel (2) towards ®. Warning! It is up to the driver to exercise discretion to select the appropriate setting given road conditions, traffic, driver’s preferred driving style and applicable laws and driving recommendations for safe following distance. To switch the distance warning function on or off: To switch on – press upper half of switch (1). The indicator lamp in the switch lights up. If the Distronic menu is active in the multifunction display, a loudspeaker symbol appears. 1 Switch – for distance warning function 2 Thumbwheel – for setting distance Distronic provides a safe following distance range to the vehicle in front. The medium setting is noticeable by a detent in the center position of the thumbwheel (2). If you want to: • Increase distance – turn thumbwheel (2) towards ¯. To switch off – press lower half of the switch (1). The indicator lamp in the switch goes out. If the Distronic menu is active in the multifunction display, the loudspeaker symbol disappears. See page 271 for distance warning function and page 274 for multifunction displays. Index part3_01.fm Seite 273 Montag, 7. Mai 2001 7:05 07 Notes: With the distance warning function activated, you will still be advised by an intermittent audible warning if a potential emergency braking circumstance has been detected, even if Distronic has been deactivated. The last selected warning function mode (on/off) will be stored in memory, even when removing the electronic key from the starter switch. Driving systems Instruments and controls 273 Operation Driving Instrument cluster display Practical hints Car care Technical data Index part3_01.fm Seite 274 Montag, 7. Mai 2001 7:05 07 Instruments and controls Operation Driving systems Multifunction displays Driving Instrument cluster display Practical hints Car care Technical data 274 1 Distronic is deactivated. The actual distance (5) and the should-be distance (6) to the vehicle ahead (4) are displayed. 2 Activating Distronic. The display with the selected speed is shown for approximately 5 seconds. 3 Distronic is activated. The message “DISTRONIC OFF” appears for approximately 5 seconds when Distronic is being deactivated. 4 Vehicle ahead. Only appears if a vehicle is detected ahead. 5 Actual distance to vehicle ahead. 6 Should-be distance to vehicle ahead (as calculated by Distronic). 7 Own vehicle. 8 Distance warning function is activated, see page 271. To call up Distronic display: Press button è or ÿ on the multifunction steering wheel repeatedly until the display (1 or 3) appears. Index part3_01.fm Seite 275 Montag, 7. Mai 2001 7:05 07 Displays in the speedometer dial When Distronic system is activated, one or two segments around the speed stored in memory light up in the speedometer dial. If a vehicle is detected ahead, those segments in the speedometer dial light up that indicate the speed range from the speed of the vehicle in front up to the Distronic stored speed. When the vehicle in front can no longer be detected, only the segments around the stored speed light up. The vehicle is accelerated to the stored speed. Driving systems Instruments and controls 275 Operation Driving Instrument cluster display Practical hints Car care Technical data Index part6_01.fm Seite 385 Montag, 7. Mai 2001 7:05 07 Instruments and controls Operation Driving Instrument cluster display Cleaning and care of the vehicle Practical hints Car care Technical data 385 Cleaning the parktronic system sensors Cleaning the Distronic system sensor P54.25-2003-26 Use a mild car wash detergent, such as Mercedes-Benz approved Car Shampoo, with plenty of water to clean the sensor (1). To prevent scratches, never apply strong force and only use a soft non-scratchy cloth when cleaning the sensors. Do not attempt to wipe dirty sensors with a dry cloth or sponge. Note: Restart the engine after cleaning the sensor (1). Use a mild car wash detergent, such as Mercedes-Benz approved Car Shampoo, with plenty of water. When using a steam cleaner or power washer, aim nozzle only briefly from a minimum distance of 4 in. (10 cm) at sensors (1). To prevent scratches, never apply strong force and use only a soft, non-scratchy cloth when cleaning the sensors. Do not attempt to wipe dirty sensors with a dry cloth or sponge. Index DaimlerChrysler VSE/IA Prüfung/Freigabe Projekt : Operator's Manual USA MY2002 Thema/Umfang : Distronic (DTR) Ersteller : M. Kinzel (mühlbauer+partner) Prüfer : G Korrektur Hr. Lauer (07031-90-77279) Prüfstatus: G in Ordnung ______________________ Datum/Unterschrift Prüfer
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Encryption : Standard V1.2 (40-bit) User Access : Print, Copy, Annotate, Fill forms, Extract, Assemble, Print high-res Create Date : 2001:05:07 07:07:38 Producer : Acrobat Distiller 4.0 for Windows Author : W H Creator : Adobe Illustrator(TM) 7.0 Title : 54702195.eps Modify Date : 2001:05:07 07:14:58+02:00 Page Count : 19 Has XFA : NoEXIF Metadata provided by EXIF.tools