Automotive Distance Control Systems SRR2A SRR2-A AUTOMOTIVE SENSOR, BLIND SPOT DETECTION User Manual SRR2 A Exhibit 1 User Manual V11

Automotive Distance Control Systems GmbH SRR2-A AUTOMOTIVE SENSOR, BLIND SPOT DETECTION SRR2 A Exhibit 1 User Manual V11

Contents

Users Manual

SRR2-A / BSM Users Manual C PSAD A D F6 Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.1 Document maturity: released Department: C PSAD A D F6 page 1 of 13 Copyright  by Continental 2010 All rights reserved User Manual for 24 GHz Blind-Spot Radar Sensor SRR2-A
SRR2-A / BSM Users Manual C PSAD A D F6 Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.1 Document maturity: released Department: C PSAD A D F6 page 2 of 13 Copyright  by Continental 2010 All rights reserved AUTHORS Name Organisation Section Frank Gruson Continental, C PSAD A D F6 Frequency Management WW Issue status (Index) Document maturity (draft / valid) Date of Issue (200x-MM-DD) Document Owner Department Description 1.0 Released 2010-12-16 Frank Gruson C PSAD A D F6 1.1 Released 2011-09-29 Frank Gruson C PSAD A D F6 Add FCC labeling requirements
SRR2-A / BSM Users Manual C PSAD A D F6 Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.1 Document maturity: released Department: C PSAD A D F6 page 3 of 13 Copyright  by Continental 2010 All rights reserved 1 TABLE OF CONTENTS 1 TABLE OF CONTENTS ............................................................................................................................................... 3 2 PURPOSE ........................................................................................................................................................................ 4 3 SYSTEM OPERATIONAL DESCRIPTION ............................................................................................................... 5 4 SRR2-A SENSOR WARNING ACTIVATION ZONE ............................................................................................... 7 5 SRR2-A SENSOR COMPONENT DESCRIPTION ................................................................................................... 8 6 SRR2-A SENSOR SOFTWARE OPERATION ........................................................................................................... 9 7 SRR2-A RADIATION HAZARD ................................................................................................................................ 10 8 SRR2-A EQUIPMENT AUTHORIZATION ............................................................................................................. 11 9 SRR2-A LABELING .................................................................................................................................................... 12
SRR2-A / BSM Users Manual C PSAD A D F6 Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.1 Document maturity: released Department: C PSAD A D F6 page 4 of 13 Copyright  by Continental 2010 All rights reserved 2 Purpose In this document an operational description of Continental´s 24 GHz blind spot radar sensor SRR2-A is given. Sufficient information is provided to understand the operation principle, the set up and the tuning of the radar sensor.
SRR2-A / BSM Users Manual C PSAD A D F6 Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.1 Document maturity: released Department: C PSAD A D F6 page 5 of 13 Copyright  by Continental 2010 All rights reserved 3 System operational description
SRR2-A / BSM Users Manual C PSAD A D F6 Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.1 Document maturity: released Department: C PSAD A D F6 page 6 of 13 Copyright  by Continental 2010 All rights reserved (depending on the implementation by the customer)
SRR2-A / BSM Users Manual C PSAD A D F6 Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.1 Document maturity: released Department: C PSAD A D F6 page 7 of 13 Copyright  by Continental 2010 All rights reserved 4 SRR2-A sensor warning activation zone Figure 1: SRR2-A warning activation zone
SRR2-A / BSM Users Manual C PSAD A D F6 Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.1 Document maturity: released Department: C PSAD A D F6 page 8 of 13 Copyright  by Continental 2010 All rights reserved 5 SRR2-A sensor component description The SRR2-A sensor consists of the following components: • Plastic housing with sensor CAN connector and sealing • RF antenna board which is plugged into the housing • EMC shield to protect the RF board from digital noise of the ECU board • An aluminum back cover closes the sensor and serves as a mounting area for the sensor to be mounted to the car. Typical mounting angle is 20°C with respect to the driving direction. Figure 2: SRR2-A sensor drawing Housing RF Antenna EMC Shield ECU board Back Cover
SRR2-A / BSM Users Manual C PSAD A D F6 Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.1 Document maturity: released Department: C PSAD A D F6 page 9 of 13 Copyright  by Continental 2010 All rights reserved 6 SRR2-A sensor software operation Only one operational mode exists which does radar measurements with FM frequency modulation. The sensor operates in this mode during the complete lifetime in the host car. The sensor SW of the test sensors for type approval is configured in such a way that the sensor enters its operational mode once a 12 V battery supply is applied to the supply pin and 0V of the battery is applied to the GND pin. No CAN message protocol or diagnostic handshake protocol is necessary in this special mode.
SRR2-A / BSM Users Manual C PSAD A D F6 Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.1 Document maturity: released Department: C PSAD A D F6 page 10 of 13 Copyright  by Continental 2010 All rights reserved 7 SRR2-A radiation hazard This BSM (blind spot monitoring) device emits intentional electromagnetic radiation in the 24,05 to 24.25 GHz frequency range. At a distance of 20cm from the sensor, the radiated power is 0.0027mW/cm2 Data from “Test report 206-11R1” of COMPLIANCE WORLDWIDE, INC, section 6, page 18 This value is a factor of 370 below the legal human exposure protection limit of 1 mW/ cm2 (MPE) in Europe and US.
SRR2-A / BSM Users Manual C PSAD A D F6 Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.1 Document maturity: released Department: C PSAD A D F6 page 11 of 13 Copyright  by Continental 2010 All rights reserved 8 SRR2-A equipment authorization This BSM devices complies with part 15 of the FCC rules (15.249), with RSS-310 of Industry Canada, and with EN 302 858 of ETSI/CEPT on a Class1 basis. Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. 3. This device may only work when the vehicle is in operation. In Europe operation is allowed in the R & TTE countries: Country 2-digit country code according to ISO 3166 Country 2-digit country code according to ISO 3166 Belgium BE Netherlands NL Bulgaria BG Norway NO Denmark DK Austria AT Germany DE Poland PL Estonia EE Portugal PT Finnland FI Romania RO France FR Sweden SE Greece GR Switzerland CH Ireland IE Slowakia SK Island IS Slovenia SI Italy IT Spain ES Latvia LV Czech Republic CZ Liechtenstein LI Turkey TR Litauen LT Hungary HU Luxemburg LU United Kingdom GB Malta MT Cyprus CY In addition, SRR2-A complies with the radio regulations of Japan, China, Korea, Russia, Ukraine, Singapore, Australia, New Zealand, Mexico and many other countries worldwide. For countries not mentioned in this chapter and not mentioned on the car´s user manual, the SRR2-A radar device has to be deactivated.
SRR2-A / BSM Users Manual C PSAD A D F6 Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.1 Document maturity: released Department: C PSAD A D F6 page 12 of 13 Copyright  by Continental 2010 All rights reserved 9 SRR2-A labeling (on sensor) USA: FCC-ID: OAYSRR2A (warning statement will be written in user manual, as the sensor is smaller as a hand and the label is not visible to the end user) Canada: Canada 310 (cathegory 2 equipment) China CMIIT ID: 2011DJ2982 Korea + KCC-CEM-C1A-SRR2A Japan: Russia EU:
SRR2-A / BSM Users Manual C PSAD A D F6 Filename: SRR2-A Exhibit 1 - User_Manual_V11.doc Issue status: 1.1 Document maturity: released Department: C PSAD A D F6 page 13 of 13 Copyright  by Continental 2010 All rights reserved 10 SRR2-A labeling (in users manual) USA: FCC-ID: OAYSRR2A This device complies with part 15 of the FCC Rules and Industry Canada RSS- 310. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation Canada: Canada 310 (cathegory 2 equipment) China CMIIT ID: 2011DJ2982 Korea + KCC-CEM-C1A-SRR2A Japan: Russia Ukraine EU: + Declaration of Conformity to R&TTE directive 1999/05/EC

Navigation menu