Autonet Mobile ANMSTWRTR-01 In-Car Router User Manual

Autonet Mobile In-Car Router UConnectIstallGuide

a href="https://usermanual.wiki/Autonet-Mobile" itemprop="url"> Autonet Mobile >

Contents

Installation Guide

© 2008 Autonet Mobile Inc.In-Car RouterSerial Number
1WARNINGTo prevent injury or fire, take thefollowing precautions:• When extending the ignition, battery, orground wires, make sure to use auto-motive grade wires or other wires with adiameter of Xmm (AWG 16) or more toprevent wire deterioration and damage tothe wire coating.• To prevent a short circuit, never put orleave any metallic objects (such as coins ormetal tools) inside the unit.• If the unit starts to emit smoke orstrange smells, disconnect immediately andconsult the Autonet Mobile CustomerService Center.• Do not touch the In-Car Router duringuse because the surface of the unit be-comes hot and may cause burns if touched.• Mounting and wiring this product re-quires skills and experience. For safety’ssake, leave the mounting and wiring workto professionals.CAUTIONTo prevent damage to the In-Car Router,take the following precautions:• Be sure the In-Car Router is connectedto a 12v DC power supply with a negativeground connection.• Do not open the bottom covers of theIn-Car Router.• Do not install the In-Car Router in a spotexposed to direct sunlight or excessive heator humidity. Also avoid places with too muchdust or the possibility of water splashing.• When replacing a fuse, only use a newone with the prescribed rating. Using afuse with the wrong rating may cause yourunit to malfunction.• To prevent a short circuit when replacinga fuse, first disconnect the wiring harness.NOTE• If you experience problems during instal-lation, consult the Autonet Mobile Cus-tomer Service Center.• If the In-Car Router does not seem to beworking right, consult the Autonet MobileCustomer Service Center.Wiring• Take the power wire for the In-CarRouter directly from the ignition powersource. If it’s connected to the vehicleswiring harness, it can cause blown fuses,etc. If it is connected directly to the carsbattery it can deplete the battery.• Do not allow the wire to directly contactthe edge of the iron plate by using grom-mets.• Connect the ground wire to a metal partof the car chassis that acts as an electricalground passing electricity to the battery’snegative terminal. Do not turn the poweron if the ground wire is not connected.• Be sure to install the protective fuse inthe power cord.• For the power cord and ground, use avehicle type (fireproof) power wiring cordwith a current capacity greater then theunits fuse capacity. Use a power cord witha diameter 8mm (AWG 8) or greater.Cleaning the In-Car RouterIf the In-Car Router becomes dirty, turnoff the power and wipe the panel with adry silicone cloth or soft cloth.Do not wipe the In-Car Router with a hardcloth or a cloth dampened by volatile sol-vents such as paint thinner and alcohol.They can scratch the surface of the In-CarRouter and/or cause the sealant to peel off.To prevent the battery from drainingplease refrain from leaving the key in theACC on position. This powers the In-CarRouter up and could possibly deplete thebattery.The Autonet Mobile installation instructions must be followed to minimizepotential interference with other electronics on the vehicle.Safety Precautions
Download:
Mirror Download [FCC.gov]
Document ID1100969
Application IDNFafilJmi6tjG4YCsLFtzQ==
Document DescriptionInstallation Guide
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize17.91kB (223878 bits)
Date Submitted2009-04-23 00:00:00
Date Available2009-04-23 00:00:00
Creation Date2008-08-26 09:43:53
Producing SoftwareQuarkXPress(R) 7.31
Document Lastmod2008-10-08 10:15:48
Document TitleUConnectIstallGuide
Document CreatorQuarkXPress(R) 7.31
FCC ID Filing: VOI-ANMSTWRTR-01

Navigation menu