Avaya Canada NTMQ75AA User Manual 05 08 0245 radio Installation1 02

Download:
Mirror Download [FCC.gov]
Document ID	6982
Application ID	v3fm+svy18qXLoyKDFA25w==
Document Description	Users Manual installation
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	51.16kB (639515 bits)
Date Submitted	1998-09-14 00:00:00
Date Available	1998-10-29 00:00:00
Creation Date	1998-09-03 16:30:13
Producing Software	Acrobat Distiller 3.01 for Windows
Document Lastmod	0000-00-00 00:00:00
Document Title	05-08-0245 radio Installation1.02.fm
Document Creator	FrameMaker+SGML 5.5P4f

Installation Method – 02-0245
September 3, 1998
Issue Number: 01.02
Information subject to change without notice. This is a DRAFT copy
for review and to provide advance information. Document release
subject to IM verification. Errors, omissions and corrections should be
sent to: lthomp@nortel.com
Pkgid: 0000003
PROPRIETARY INFORMATION: The information contained in this document
is the property of Nortel (Northern Telecom). Except as specifically authorized
in writing, the holder of this document shall keep all information contained
herein confidential and shall protect same in whole or in part from disclosure
and dissemination to third parties.
 Nortel 1998
All Rights Reserved
Draft
Picocell 1900 Radio Unit Installation
September 3, 1998
Method 02-0245
1.0 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 Reason for Reissue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.0 Material Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1 Required Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.2 Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3 Stock List and Mounting Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.4 Customer Supplied Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.0 Precautions and Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.2 Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.0 Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Procedure 1 – Unpacking and Inventory transciever Material . . . . . . . . . . . . . . . .
Procedure 2 – Wall Mounting and securing the Radio Mounting Bracket . . . . . . .
Procedure 3 – Ceiling Mounting and securing the Radio Mounting Bracket . . . . .
Procedure 4 – Installation of PICOCELL Transceiver onto Wall Mounting Bracket
Procedure 5 – Co-located AC power supply Installation . . . . . . . . . . . . . . . . . . .
Procedure 6 – Remote AC power supply Installation . . . . . . . . . . . . . . . . . . . . . .
4.2 Power Supply connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3 PICOCELL Transceiver Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.0 References
13
13
14
15
17
19
20
21
22
23
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
6.0 Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix A - PICOCELL 1900 transciever Cover removed Top view . . . . . . . . . . . . . .
Appendix B - Mounting Orientation and Isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix C - Picocell 1900 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
25
26
27
AC REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Picocell 1900 Power Supply Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Last Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Picocell 1900 Radio Unit Installation / 3
Draft
Table of Contents
Draft
Method 02-0245
4 / Picocell 1900 Radio Unit Installation
September 3, 1998
September 3, 1998
Method 02-0245
Figure 1 – You are here diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 2 – PICOCELL 1900 front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 3 – PICOCELL 1900 transciever Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 4 – PICOCELL 1900 Bottom view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 5 – PICOCELL 1900 Wall Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 6 – Track Ceiling support IDSClips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 7 – PICOCELL 1900 transciever Ceiling mounting . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 8 – Locking the transciever into the mounting Bracket . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 9 – PICOCELL 1900 Co-located power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 10 – Remote Power Supply Mounting (Typical) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 11 – Power supply and connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 12 – PICOCELL 1900 transciever Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 13 – PICOCELL 1900 cabling and connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Picocell 1900 Radio Unit Installation / 5
Draft
Illustrations
Method 02-0245
September 3, 1998
Draft
Tables
Tools
Stock List and Mounting Kits
Mounting Hardware
6 / Picocell 1900 Radio Unit Installation
13
14
14
September 3, 1998
Method 02-0245
1.0 General Information
Purpose: This method will describe how to unpack and install the
PICOCELL 1900 Transceiver).
Equipment: The PICOCELL 1900 Transceiver and mounting
hardware.
Application: This method will cover installation of initials, upgrades
and extensions.
Service Impact: There is no service impact at this time.
1.2 Sequence
1.
This method is to be performed after the building cabling has been
installed and is ready to recieve the PICOCELL 1900 Transceivers.
2.
PICOCELL 1900 Planning Method 04-0242 has been reviewed.
1.3 Reason for Reissue
Changes from Project Team Review Sept 1, 1998:
• Updated section 4.2 Power supply
• Revised figures 5, 8, 9
• Section 5 removed reference
• Global change MBS1900 to Picocell 1900
• Cleared Table 3 contents until mounting hardware is finalized
Picocell 1900 Radio Unit Installation / 7
Draft
1.1 Description
Method 02-0245
September 3, 1998
Figure 1 – You are here diagram
Draft
IM 04-0242
PICOCELL 1900
General Information
and Plannng
Educate Yourself
IM 04-0241
CSI Installation and
Planning
Mount the back board
and plan lay out s
IM 04-0243
CSI Handling and
securing
IM 04-0243
CSI Handling and
securing
IM 04-0244
PICOCELL 1900
Cabling and Cross
Connect
IM 04-0246
PICOCELL 1900
Radio and CSI Power
up
Check the site and plan
the Job
IM02-0242
PICOCELL 1900
General Information
and Plannng
Install the CSI bracket
and mount the CSI and
PICOCELL 1900 power
supplies
Install PICOCELL 1900
mounting bracket(s),
Hybrids and Antennas
IM02-0245, 12-0152
PICOCELL 1900 Unit
and Antenna
Installation
Mount the CSI crossconnect blocks
Make PICOCELL 1900
Connections and lock
into bracket
IM02-0245
PICOCELL 1900 Unit
Installation
Jumper PICOCELL
1900 to CSI and power
supply on cross-connect
blocks
IM 04-0244
PICOCELL 1900
Cabling and Cross
Connect
Power up PICOCELL
1900 Radios and
perform commissioning
test
IM 04-0246
PICOCELL 1900
Radio and CSI Power
up
Cable the CSI to the
cross-connect blocks
Power up CSI
Commission PICOCELL
1900 transcievers
IM28-0248
Radio Commisioning with
the IFR
Load CSI and Radio
software and run
diagnostics
IM28-0247
CSI Equipment Loading
and Diagnostics
Test Integrated System
8 / Picocell 1900 Radio Unit Installation
IM02-0249
Microcell System
Test
September 3, 1998
Method 02-0245
2.0 Material Requirements
Installation Safety Manual (ISM/IM0) - can be requested from the
Regional Tool Facility.
2.2 Tools
The tools listed in Figure 2 are required to perform this method.
Table 1 – Tools
U.S. Tool
Canadian
Tool
Tool Kit
Tool Kit
Description
Installers Tool Kit
2.3 Stock List and Mounting Kits
Table 2 – Stock List and Mounting Kits
Quantity
CPC/PEC
Product Description
P0880222
NTMQ7025
PICOCELL Point of Use Power Supply
NTMQ40AA
Picocell Basestation, 1900MHz A Band
NTMQ50AA
Picocell Basestation, 1900MHz B Band
NTMQ60AA
Picocell Basestation, 1900MHz C Band
NTMQ70AA
Picocell Basestation, 1900MHz 60MHz Band
NTMQ75AA
Picocell Basestation, 1900MHz 60MHz Band
PICOCELL 1900 Mounting bracket
Table 3 – Mounting Hardware
Quantity
CPC/PEC
Product Description
Picocell 1900 Radio Unit Installation / 9
Draft
2.1 Required Documents
Method 02-0245
September 3, 1998
Draft
Figure 2 – PICOCELL 1900 front view
2.4 Customer Supplied Equipment
1.
Building wiring must be installed between each PICOCELL 1900
transceiver location and the equipment location where the CSI is
located. The mounting of each PICOCELL 1900 transceiver is
independent of CSI and MDF which may be installed later.
2.
Floor plans indicating PICOCELL 1900 mounting locations and
locations for CSI and MDF
3.
Cabling and pair assignment matching PICOCELL 1900 transceivers to
cable pair numbers.
4.
Building access authorization, security clearance if required and keys
for access to restricted CSI and PICOCELL 1900 equipment locations.
10 / Picocell 1900 Radio Unit Installation
September 3, 1998
Method 02-0245
3.0 Precautions and Preparations
Observe the general safety precautions against personal injury and
equipment damage outlined in the ISM/IM0 at all times.
Picocell transcievers may be handled without static protection. Use of
a grounded wrist strap is mandatory when handling all other exposed
circuit packs or modules.
This method is for indoor installations only.
Picocell 1900 transcievers and antennae are for indoor installations only
and mounting of some or all; transcievers, antennas, hybrids and cabling
in an outside environment may create a potential fire hazard from
lightning. Custom design is required to address outdoor requirements.
Avoid thermal trapped air cavities. In particular, the Picocell cannot be
mounted above the ceiling as this is deemed a plenum installation, and
different, tighter safety specifications are enforced.
CAUTION
Maintain minimum or greater distances from interference
sources and from equipment and apparatus which may be
affected by RF energy.
3.2 Preparations
Prior to starting the operations presented in this method, arrange all
materials, tools, and test equipment at the work location so as to
minimize fatigue and inconvenience.
1.
Has an Installation Planning Checklist per IM-0242 been completed?
2.
Are System design and site floor plans available with equipment
locations ?
3.
Is building wiring installed and accessible?
4.
Is all the test equipment necessary to complete the job on site?
5.
Is all the PICOCELL transceiver and antenna equipment on site and
inventoried?
6.
Is the customer supplied equipment (back boards, MDF blocks) on site
and installed?
7.
Has the loadbuild sent all required switch load tapes to the MTX site?
Picocell 1900 Radio Unit Installation / 11
Draft
3.1 Precautions
Method 02-0245
September 3, 1998
8.
Are System T1s facilities ordered (if required) and what is the
availability date?
9.
Is the antenna system design cabling Interconnect Schematic available?
Draft
Figure 3 – Transciever Assembly
P0880222
Antenna
Element
P0880211
LED indicators
Cover P0880217
Interface Cover P0880218
12 / Picocell 1900 Radio Unit Installation
September 3, 1998
Method 02-0245
4.0 Procedure
4.1 Overview
Procedure 1 - Unpacking and Inventory transciever Material
Procedure 2 - Wall Mounting and securing the Radio Mounting Bracket
Procedure 3 - Ceiling Mounting and securing the Radio Mounting
Bracket
Procedure 4 - Installation of PICOCELL Transceiver onto Wall
Mounting Bracket
Procedure 5 - Co-located AC power supply Installation
Procedure 6 - Remote AC power supply Installation
Picocell 1900 Radio Unit Installation / 13
Draft
Below is a list of procedures required to install the PICOCELL 1900:
Method 02-0245
September 3, 1998
Procedure 1 – Unpacking and Inventory transciever Material
Draft
Step
Action
Inspect the cartons for any damage.
Refer to Section 2.3 Product Stock List
and Mounting Kits, for a list of parts to
be included in the cartons
Remove all equipment from their cartons
and verify the equipment received is not
damaged. After all of the parts are
removed from the cartons and inspected,
inventory them making sure that all the
parts listed in Section 2.3 are on site.
Refer to the PICOCELL 1900 Installation Planning Method 02-0242 and the
System Design Specification to determine how many CSI and PICOCELL
1900 (PICOCELL 1900 Base Station)
transcievertranscievers are required and
to determine where and how to position
the units.
Also take into consideration the desired
location of the Hybrid. Due to the length
of the antenna cables, the transceiver(s)
and Hybrid(s) will have to reside close
together. Refer to the PICOCELL 1900
Installation Planning Method 04-0242
and Antenna installation 12-0152 for
spacing requirements and cable length
considerations.
14 / Picocell 1900 Radio Unit Installation
Observation
Table 2, “Stock List and Mounting Kits,” on
page 9
September 3, 1998
Method 02-0245
..
Procedure 2 – Wall Mounting and securing the Radio Mounting Bracket
Action
Observation
Locate the wall mounting bracket and
the screws provided. Determine the
required direction transcieverf the wall
mount bracket orientation from the System Design floor plan. Refer also to
Appendix B - Orientation
Locate the 4 mounting screws with the Figure 4
mounting bracket . If external antennas
are used, the transcievers and Hybrid(s)
will have to reside close together. Reference Method 04-0152 for antenna system installation.
Square the bracket with the wall and/or
ceiling and fasten the bracket with the
first screw.
After one top corner has been fastened
to the wall, check to make sure the wall
mounting bracket is still level before
installing the additional wood screws
Install the remaining wood screws into
the wall mounting bracket.
Position the transciever into the bracket
and ensure that the locking retainer is
locked and correctly positioned .
Draft
Step
Appendix B
Figure 4
Picocell 1900 Radio Unit Installation / 15
Method 02-0245
September 3, 1998
Draft
Figure 4 – PICOCELL Transceiver Bottom view
Figure 5 – PICOCELL Wall Mount
Wall Studs
Wall Stud
Wall Mount
Mounting Bracket
P0880222
Latch Locking
16 / Picocell 1900 Radio Unit Installation
Mounting Bracket
P0880222
Backboard
Wall Mount
September 3, 1998
Method 02-0245
Procedure 3 – Ceiling Mounting and securing the Radio Mounting Bracket
Action
Observation
Draft
Step
Locate the wall mounting bracket and
the screws provided. Determine the
desired direction of the wall mount
bracket orientation. Refer to the system
layout document to determine readio
orienation.
Figure 6
Locate the ceiling main support track
closest to the desired mounting location
and attach the IDS clips as shown in Figure 6 . If the ceiling track is poorly supported use drop wire from each IDS clip
to a secure point above the mouning
location in main ceiling. Replace the
ceiling panel
Attach the mounting bracket to the ceiling as shown in Figure 7 using spacers
between the bracket and the IDS clips.
Appendix B
Note that the nuts on the IDS clips must be flusch
to permit the transciever to lock into the mounting bracket to
Drill an access hole near the front of the
transciever for the facility cable pairs.
Lock the transciever into the bracket and
complete the wired connections.
Picocell 1900 Radio Unit Installation / 17
Method 02-0245
September 3, 1998
Figure 6 – Track Ceiling support IDSClips
Draft
Drop wire
Ceiling Panel
Ceiling support
Track
Spacer
Ceiling Panel
Mouinting
Bracket
Mouinting
Bracket
Figure 7 – PICOCELL Transciever Ceiling mount
Cross Track
IDS Clip
X3
Mounting
Bracket
Main Ceiling
Track
Spacer
x3
Washer
x3
Nut
x3
18 / Picocell 1900 Radio Unit Installation
September 3, 1998
Method 02-0245
Procedure 4 – Installation of PICOCELL Transceiver onto Wall Mounting Bracket
Action
Observation
Remove the connector access cover and
position the transciever onto the mounting bracket and slide the unit so that the
radio locks onto the bracket and the
retainer catch engages with the latch
hole.
At this point PICOCELL 1900 wiring
connections can be completed by opening the interface panel cover and making
connections per Figure 12.
PICOCELL 1900 cabling and commissioning can be completed, proceed with
Method 12-0152 and 04-0244.
See Figure 4 and Figure 8
Figure 8 – Locking the transciever into the mounting Bracket
P08800222
Mounting Bracket
Radio unit
Locking
Retainer
Picocell 1900 Radio Unit Installation / 19
Draft
Step
Method 02-0245
September 3, 1998
Procedure 5 – Co-located AC power supply Installation
Draft
Step
Action
Observation
Note that an AC outlet must be provided by a
qualified electrician.
Locate the AC-DC power supplies and mount as
shown in Figure 9. Coil excess cord and tie back
excess cable with tie wraps.
Connect the power supply to the transciever and
terminate power wires as shown on Figure 12
Plug the power supply into the AC outlet and
verify the supply output power.
Verify the transciever operation in IM 04-0246
Figure 9 – PICOCELL Co-located power supply
20 / Picocell 1900 Radio Unit Installation
- 48VDC
transciever powers up with activity on LEDs
September 3, 1998
Method 02-0245
Procedure 6 – Remote AC power supply Installation
Action
Observation
Note that AC outlets must be provided by a
qualified electrician.
Locate the AC-DC power supplies and mount as
shown in Figure 10. Coil excess cord and tie
back excess cable with tie wraps.
Connect the power supply jumpers to the MDF
blocks see IM-04-0244 for jumpers and cabling.
transciever and terminate power wires as shown
on Figure 10
Plug the power supply into the AC outlet and
verify the supply output power.
Verify the transciever operation in IM 04-0246
See IM 18-0244 fro cabling and jumpering of DC
power.
AC outlet placement per IM 04-0241 and Figure 10.
- 48VDC
Figure 10 – Remote Power Supply Mounting (Typical)
CSI
Jumper Rings
-48V
110VAC
Jumper Routing
AC-DC
1 .0 "
-48VDC
AC-DC
-48VDC
AC-DC
45"
-48VDC
3 7 .0 "
AC-DC
-48VDC
AC-DC
9 .2 "
-48VDC
3.0"
AC-DC
AC-DC
-48VDC
-48VDC
AC-DC
AC-DC
-48VDC
-48VDC
AC-DC
AC-DC
-48VDC
-48VDC
AC-DC
AC-DC
-48VDC
-48VDC
AC-DC
AC-DC
-48VDC
-48VDC
AC Power Bars
Picocell 1900 Radio Unit Installation / 21
Draft
Step
Method 02-0245
September 3, 1998
The PICOCELL 1900 transciever is powered by an AC to -48VDC
supply which is mounted either at the CSI location or near the
PICOCELL transceiver mounting position. If it is mounted near the
transciever (co-located), an AC outlet must also be within close
proximity. When the supply is co-located near the transceiver, the
power wiring may or may not be accommodated in the station wiring
conduit and may need to be dressed neatly on the wall or ceiling surface.
See Figure 9.
See IM 02-0241 for placement, mounting and connection of the power
supply at the remote CSI location.
Figure 11 – Power supply and connections
48V
6.5"
0.7"
Grd
3 terminal IEC 320 Jack
120VAC
1.0"
Draft
4.2 Power Supply connections
4.0"
22 / Picocell 1900 Radio Unit Installation
September 3, 1998
Method 02-0245
4.3 PICOCELL Transceiver Connections
Draft
Connections to the PICOCELL 1900 transciever consist of bare wire
terminations on the PICOCELL 1900 terminal strip which provides
terminals for the following:
Figure 12 – PICOCELL transciever Connections
Terminal port Radio 1
TX/RX 2
TX/RX 1
-48V
+Grd
Terminal Port Radio 2
TCM 1 TCM 2
T R
T R
- +
- +
Figure 13 – PICOCELL 1900 cabling and connections
From
Frame
Block Pos
Pair
Description
TCM 1 T (-)
MDF
1T
TCM 1 R (+)
MDF
1R
Power - 48V
MDF
2T
Power - 48V
MDF
2R
TCM 2 T (-)
MDF
3T
TCM 2 R (+)
MDF
3R
Power + Grd
MDF
4T
power+ Grd
MDF
4R
Picocell 1900 Radio Unit Installation / 23
Method 02-0245
September 3, 1998
5.0 References
Draft
Document
Number
Title
IM
04-0241
PICOCELL 1900 CSI Installation and Planning
IM
04-0242
PICOCELL 1900 General Information and Plannng
IM
08-0243
PICOCELL 1900 CSI Equipment Handling and Securing
IM
04-0244
PICOCELL 1900 System Cabling and Cross Connect
IM
12-0152
PICOCELL 1900 Antenna System Installation
IM
02-0245
PICOCELL 1900 transciever Installation
IM
22-0246
PICOCELL 1900 Radio and CSI Power up
IM
24-0247
PICOCELL 1900 Equipment Loading and Diagnostics
IM
28-0248
PICOCELL 1900 Radio Commissioning with the IFR 1900
IM
28-0249
PICOCELL 1900 System Test
24 / Picocell 1900 Radio Unit Installation
September 3, 1998
Method 02-0245
6.0 Appendices
Draft
Appendix A - PICOCELL 1900 transciever Cover removed Top view
Picocell 1900 Radio Unit Installation / 25
Method 02-0245
September 3, 1998
Appendix B - Mounting Orientation and Isolation
P0880222
Mounting Bracket
P0880222
Mounting Bracket
Arrangement A
Draft
Arrangement B
P0880222
P0880222
Mounting Bracket
Mounting Bracket
Wire entrance
Wall or Ceiling outlet box
Wire entrance
Note: Ensure station wiring does not loop or coil
near the PICOCELL 1900 antenna. The unit
installation should mount as shown with
maximum spacing between the antenna and
entrance wiring to avoid interference with RF
signals.
26 / Picocell 1900 Radio Unit Installation
September 3, 1998
Method 02-0245
Appendix C - Picocell 1900 Technical Specifications
• Maxcimum length twisted pair distribution, 3000’ (TCM)
• 1900MHz Version IS 136 TDMA operation
• 100mW (+20dBm) ERP
• 2 RF channels per PICOCELL 1900 RF unit (Internal duplexer)
• Internal Omni Antenna
• Receiver Diversity
• Distributed Omni and directional Antenna Support
• 4 twisted pair per unit for power and digital link (TCM)
• 48 Volt DC power 32W nominal
• Visually pleasing, non-obtrusive design
• Individual transciever Alarms
• 15 PICOCELL 1900s per CSI (30 RF channels)
• Standard Nortel TRU maintenance interface.
• 12.8" W x 13.6" L x 3.25" D
• 14 lb unit weight
AC REQUIREMENTS
Each non-switched dedicated outlet must have the following:
• Voltage110 - 120 VAC
• Frequency47Hz to 53Hz or 57 Hz to 63 Hz
• Power (I/P max)300 VA
• Receptacles-120V 15A service NEMA IG 5-15R
• -208/240V 15A service NEMA IG 6 15R
• Warnings for AC power cord:
WARNING
The socket-outlet shall be installed near the equipment and shall be
easily accessible. Power cords are 6ft maximum.
Note: See local electrical codes for 240VAC outlet requirements
Picocell 1900 Radio Unit Installation / 27
Draft
• Maximum length remote Power (see IM 04-0242 section 4.2)
Method 02-0245
September 3, 1998
Picocell 1900 Power Supply Specifications
Draft
Input
• Voltage:
120/240 VAC Nominal
• Line Frequency
50/60 Hz Nominal
• Power rating
90W
• Protection
Internal primary current fuse, Inrush limiting
• Configuration
In Case IEC320 with Ground
•
6 ft., 5 Conductor, 18 AWG,
Output
• Voltage
-48VDC +/- .5V
• Nominal current
2.0 A Max.
• Combined Line and Load Voltage Regulation
• output current limiting
•
Short circuit protection
Mechanical
• 6.58 L x 4.0 W x 1.25 H(in)
• Case Material: Black 94V0 Polycarbonate
• Weight: 22 ounces, 625 grams (excluding cords)
Last Page
28 / Picocell 1900 Radio Unit Installation

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 28
Page Mode                       : UseOutlines
Create Date                     : 1998:09:03 16:30:13
Producer                        : Acrobat Distiller 3.01 for Windows
Title                           : 05-08-0245 radio Installation1.02.fm
Creator                         : FrameMaker+SGML 5.5P4f

EXIF Metadata provided by EXIF.tools