Avaya Canada UMTS1900COMP UMTS Compact iBTS User Manual 411 8111 905 03 09

Avaya Canada Corporation UMTS Compact iBTS 411 8111 905 03 09

Exhibit 8 User Manual

UMT/DCL/DD/0002411–8111–905Wireless Service Provider SolutionsUMTSProduct FundamentalsAbout the Univity iBTSUMT/DCL/DD/0002 03.09/EN Preliminary October 2003411–8111–905
Wireless Service Provider SolutionsUMTSProduct FundamentalsAbout the Univity iBTSDocument number: UMT/DCL/DD/0002411–8111–905Document issue: 03.09/ENDocument status: PreliminaryProduct release: UMTS03Date: October 2003Copyright © 2000-2003 Nortel Networks , All Rights ReservedPrinted in FranceNORTEL NETWORKS CONFIDENTIALThe information contained herein is the property of Nortel Networks and is strictly confidential. Except asexpressly authorized in writing by Nortel Networks, the holder shall keep all information contained hereinconfidential, shall disclose the information only to its employees with a need to know, and shall protect theinformation, in whole or in part, from disclosure and dissemination to third parties with the same degree ofcare it uses to protect its own confidential information, but with no less than reasonable care. Except asexpressly authorized in writing by Nortel Networks, the holder is granted no rights to use the informationcontained herein.Information is subject to change without notice. Nortel Networks reserves the right to make changes in design or components asprogress in engineering and manufacturing may warrant.Nortel Networks, the Nortel Networks logo, the Globemark, Univity iBTS, Univity RNC, Passport, and Unified Networks aretrademarks of Nortel Networks. Bussmann is a trademark of Bussmann. All other brand and product names are trademarks orregistered trademarks of their respective holders.
PUBLICATION HISTORYSYSTEM RELEASE UMTS03October 2003Issue 03.09/EN PreliminaryUpdate after internal reviewSeptember 2003Issue 03.08/EN DraftUpdate for OAM V3.1/RAN V3.1 Customer ReadinessIntroduction of UMTS 1900 Univity iBTSs Mono and Indoor CompactAugust 2003Issue 03.07/EN PreliminaryUpdate after internal reviewJuly 2003Issue 03.06/EN DraftUpdate for OAM V3.1/RAN V3.1 Customer ReadinessIntroduction of UMTS 1900 iBTSs Indoor 2 and OutdoorJuly 2003Issue 03.05/EN PreliminaryUpdate after FCC Regulatory information validationJune 2003Issue 03.04/EN DraftFCC Regulatory Information enhancement: addition of North-American rulesMay 2003Issue 03.03/EN PreliminaryUpdate after Internal ReviewApril 2003Issue 03.02/EN DraftUpdate for OAM V3.1/RAN V3.1April 2003Issue 03.01/EN StandardMinor updateNortel Networks Confidential Publication history iCopyright © 2000-2003 Nortel Networks About the Univity iBTS
Document version change (UTRAN V2.1 belong to UMTS V3.0b system release)SYSTEM RELEASE UMTS02January 2003Issue 02.08/EN StandardEditorial Update to introduce the iBTS Indoor 2November 2002Issue 02.07/EN StandardUpdate for UMTS V2.1 UTRANSeptember 2002Issue 02.06/EN PreliminaryUpdate for UMTS V2.0d UTRANJuly 2002Issue 02.05/EN PreliminaryMinor updateJuly 2002Issue 02.04/EN PreliminaryUpdate after internal reviewJune 2002Issue 02.03/EN DraftUpdate for UMTS V2.0c UTRANMay 2002Issue 02.02/EN PreliminaryUpdate after internal reviewMarch 2002Issue 02.01/EN Draft• introduction of the STSR2 configuration• introduction of the new iBTS Street• drop and insert feature descriptionSYSTEM RELEASE UMTS01February 2002Issue 01.08/EN PreliminaryUpdate after reviewNortel Networks Confidential Publication history iiUMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
January 2002Issue 01.07/EN DraftUpdate according the product release change.October 2001Issue 01.06/EN PreliminaryUpdate after reviewSeptember 2001Issue 01.05/EN DraftThe following changes were made throughout the document:• modify modules organization throughout the document• update the iBTS features according to the system release change• update the configuration rules• add the TMA description• update the PFM description• update the ac plinth description• update the batteries description• modify software sectionJuly 2001Issue 01.04/EN PreliminaryUpdate after reviewJune 2001Issue 01.03/EN DraftThe following changes were made throughout the document:• update the iBTS description and configuration according to the system release• update the hardware description• add information about physical interfaces, cabling, functional architecture, andsoftware• add and update the ancillary modules• add the configuration description• delete the dimensioning sectionJanuary 2001Issue 01.02/EN PreliminaryUpdate after reviewDecember 2000Nortel Networks Confidential Publication history iiiCopyright © 2000-2003 Nortel Networks About the Univity iBTS
Issue 01.01/EN DraftCreationNortel Networks Confidential Publication history ivUMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
About this publication 1What is in new about the Univity iBTS 3Univity iBTS regulatory information 5UTRAN introduction of the UMTS03 solution 10Univity iBTS basic characteristics 14Univity iBTS introduction 15Univity iBTS key features 24Univity iBTS characteristics 26Univity iBTS architecture and configuration 32Univity iBTS architecture 33Univity iBTS RF configuration 37Univity iBTS interfaces 54Uu interface physical description 55Iub interface physical description 56Univity iBTS hardware 57Univity iBTS hardware presentation 58Univity iBTS digital shelf 80Univity iBTS digital shelf description 81CEM (Channel Element Module) 88iCEM (internet Channel Element Module) 95CCM (Core Control Module) 100iCCM (internet Core Control Module) 104TRM (Transceiver Receiver Module) 109iTRM (internet Transceiver Receiver Module) 118GPSAM/cGPSAM (GPS and Alarm Module) 122Univity iBTS RF block 126Nortel Networks Confidential Table of contents vCopyright © 2000-2003 Nortel Networks About the Univity iBTS
Univity iBTS Radio Frequency (RF) Description 127MCPA (Multi Carrier Power Amplifier) 131Tx Splitter 136DDM (Dual Duplexer Module) 139Univity iBTS cabinet other modules 145MCA (Manufacturing, Commissioning, and Alarm) module 146Mono Control Board 151Single Power Control Module (SPCM) 153TMA (Tower Masterhead Amplifier) 155Interconnection module of the Univity iBTS 162Alarm protection module 167PCM protection module (iBTS Outdoor) 171PCM protection module (iBTS Indoor 2) 173PFM (Power Filter Module) (Univity iBTS Indoor 2100) 176User ICO of the iBTS Outdoor 177User ICO of the Univity iBTS Street 2100 178Univity iBTS cooling system 179Cooling system of the Univity iBTS Outdoor 180Fan tray of the Univity iBTS Indoor 2100 183Cooling system of the Univity iBTS Street 2100 185Cooling system of the Univity iBTS Indoor 2 188Cooling system of the Univity iBTS Indoor 1900 Compact 191Univity iBTS power system 195Power supply of the Univity iBTS Outdoor 196Power supply of the Univity iBTS Indoor 2100 202ac plinth (Univity iBTS Indoor 700 2100) 205Nortel Networks Confidential Table of contents viUMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
Power supply of the Univity iBTS Street 2100 209dc power system shelf of the Univity iBTS 211dc distribution module of the Univity iBTS Outdoor 214dc distribution module of the Univity iBTS Street 2100 216dc distribution system of the Univity iBTS Indoor 2 218dc distribution system of the Univity iBTS Mono 221dc distribution system of the Univity iBTS Indoor 1900 Compact 224Rectifier of the Univity iBTS 227Single Power Control Module (SPCM) 229Batteries of the Univity iBTS Outdoor 231Batteries of the Univity iBTS Indoor 700 232External battery cabinet 233+24 V dc/dc converter kit option 236Univity iBTS software 237Univity iBTS software overview 238CEM software 242TRM software 244CCM software 246Univity iBTS services and features 249Introduction of the Univity iBTS services and features 250Multi CEM management 253Resource allocation management 254Pool management 257Multi PCM management 258Multi PCM features 259Multi PCM feature interactions 262Nortel Networks Confidential Table of contents viiCopyright © 2000-2003 Nortel Networks About the Univity iBTS
Impact of the multi PCM feature on the network 263Nortel Networks Confidential Table of contents viiiUMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
Figure 1 - UTRAN architecture example of the UMTS03 solution (1900 MHzSONET) 11Figure 2 - UTRAN architecture example of the UMTS03 solution (2100 MHz SDH) 12Figure 3 - UTRAN architecture example of the UMTS03 solution (2100 MHz PCM) 13Figure 4 - Univity iBTS Outdoor outside view 18Figure 5 - Univity iBTS Indoor 2100 outside view 19Figure 6 - Univity iBTS Street 2100 outside view 20Figure 7 - Univity iBTS Indoor 2 outside view 21Figure 8 - Univity iBTS Mono outside view 22Figure 9 - Univity iBTS Indoor 1900 Compact outside view 23Figure 10 - Univity iBTS functional architecture 34Figure 11 - Univity iBTS hardware architecture 35Figure 12 - Univity iBTS Mono configuration 40Figure 13 - Univity iBTS Indoor 1900 Compact with OTOR1 configuration (functionaldiagram) 43Figure 14 - Univity iBTS Indoor 1900 Compact with OTOR2 configuration (functionaldiagram) 44Figure 15 - Univity iBTS Indoor 1900 Compact with BTBR1 configuration (functionaldiagram) 45Figure 16 - Univity iBTS Indoor 1900 Compact with BTBR2 configuration (functionaldiagram) 46Figure 17 - Univity iBTS Outdoor 2100, Univity iBTS Indoor 600, Univity iBTS Indoor 700,or Univity iBTS Indoor 2 2100 with OTSR1 configuration (functional diagram) 47Figure 18 - Univity iBTS Street 2100 with OTSR1 configuration (functional diagram) 48Figure 19 - iBTS Outdoor, iBTS Indoor 600, iBTS Indoor 700, or iBTS Indoor 2 withSTSR1 configuration without TRM/iTRM redundancy (functional diagram) 49Figure 20 - Univity iBTS Street 2100 with STSR1 configuration (functional diagram) 50Figure 21 - Univity iBTS Indoor 1900 Compact with STSR1 configuration (functionaldiagram) 51Figure 22 - Univity iBTS Outdoor, Univity iBTS Indoor 600, Univity iBTS Indoor 700,Univity iBTS Indoor 2, or Univity iBTS Indoor 1900 compact with STSR2 (functionaldiagram)52Figure 23 - Inside view (Univity iBTS Outdoor 2100) 59Figure 24 - Inside view (Univity iBTS Indoor 600) 61Figure 25 - Inside view (Univity iBTS Indoor 700) 62Figure 26 - Bulkhead top view (Univity iBTS Indoor 600) 63Figure 27 - Bulkhead top view (Univity iBTS Indoor 700) 64Figure 28 - Inside view (Univity iBTS Street 2100) 66Figure 29 - Cabinet layout (Univity iBTS Street 2100) 67Figure 30 - Internal cabling top view (Univity iBTS Street 2100) 68Figure 31 - Inside view (Univity iBTS Indoor 2) 69Figure 32 - Cabinet Layout (Univity iBTS Indoor 2) 70Figure 33 - Bulkhead top view (Univity iBTS Indoor 2) 71Figure 34 - Inside view (Univity iBTS Mono 2100) 73Figure 35 - Cabinet layout (Univity iBTS Mono 2100) 74Figure 36 - Bulkhead below view (Univity iBTS Mono 2100) 75Nortel Networks Confidential List of figures ixCopyright © 2000-2003 Nortel Networks About the Univity iBTS
Figure 37 - Inside view (Univity iBTS Indoor 1900 Compact 77Figure 38 - Cabinet layout (Univity iBTS Indoor 1900 Compact) 78Figure 39 - Bulkhead top view (Univity iBTS Indoor 1900 Compact) 79Figure 40 - Digital shelf description 82Figure 41 - Front view of the digital shelf (Univity iBTS Outdoor and Univity iBTS Indoor700) 83Figure 42 - Front view of the digital shelf (Univity iBTS Indoor 600) 84Figure 43 - Front view of digital shelf (Univity iBTS Street 2100) 84Figure 44 - Front view of digital shelf (Univity iBTS Indoor 2) 85Figure 45 - Front view of digital shelf (Univity iBTS Mono) 86Figure 46 - Front view of digital shelf (Univity iBTS Indoor 1900 Compact) 86Figure 47 - Overview of the CEM physical architecture 89Figure 48 - Detailed view of the CEM hardware 91Figure 49 - Interconnection of the mini backplane 92Figure 50 - Front view of the CEM 93Figure 51 - iCEM 64 functional architecture 95Figure 52 - Front view of the iCEM 64 97Figure 53 - Front view of the iCEM 128 98Figure 54 - Front view of the CCM 101Figure 55 - Interfaces of the CCM 103Figure 56 - iCCM functional architecture 105Figure 57 - Front view of the iCCM 107Figure 58 - Functional block diagram of the TRM 110Figure 59 - Block diagram of the dTRM 111Figure 60 - Block diagram of the rTRM transmitted part 112Figure 61 - Block diagram of the rTRM received part 113Figure 62 - Front view of the TRM 114Figure 63 - iTRM radio architecture (Direct Modulation) 118Figure 64 - iTRM radio architecture (Direct Demodulation) 119Figure 65 - Front view of the iTRM 120Figure 66 - GPSAM alarm and inventory diagram 123Figure 67 - Front view of the GPSAM 124Figure 68 - RF block general description 128Figure 69 - Front view of the MCPA (Univity iBTS Outdoor, Univity iBTS Indoor 2100, andUnivity iBTS Indoor 2) 129Figure 70 - Front view of the MCPA (Univity iBTS Street 2100) 129Figure 71 - Functional description of an MCPA 132Figure 72 - MCPA functional block diagram 133Figure 73 - Front view of the MCPA module 134Figure 74 - Tx Splitter functional block 137Figure 75 - Tx Splitter hardware description 138Figure 76 - DDM block diagram 140Nortel Networks Confidential List of figures xUMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
Figure 77 - Front view of DDM (iBTS Outdoor, iBTS Indoor 2100, and iBTS Indoor 2) 141Figure 78 - Front view of DDM (iBTS Street 2100 and iBTS Mono) 142Figure 79 - Front view of DDM-2 (iBTS Outdoor, iBTS Indoor 2100, and iBTS Indoor 2) 143Figure 80 - Front view of the MCA module (Univity iBTS Outdoor) 146Figure 81 - Front view of the MCA module (Univity iBTS Indoor 2100) 147Figure 82 - Front view of the MCA module (Univity iBTS Street 2100) 148Figure 83 - Front view of the MCA module (Univity iBTS Mono) 149Figure 84 - Front view of MCA module 150Figure 85 - Front view of the MCA module (Univity iBTS Indoor 2) 150Figure 86 - Front view of Control board (iBTS Mono) 152Figure 87 - Front view of the SPCM 153Figure 88 - Double TMA 2100 insertion in the system 156Figure 89 - single TMA 1900 insertion in the system 157Figure 90 - TMA 2100 block diagram 158Figure 91 - TMA 1900 block diagram 159Figure 92 - Front view of single TMA 1900 module 160Figure 93 - Front view of double TMA 2100 module 160Figure 94 - Front view of ICO module (iBTS Outdoor) 164Figure 95 - Front view of ICO module (Univity iBTS Indoor) 164Figure 96 - Front view of CICO module (Univity iBTS Street 2100/Univity iBTS Indoor1900 Compact) 165Figure 97 - Front view of ICO module (Univity iBTS Indoor 2) 166Figure 98 - Front view of ICO module (Univity iBTS Mono) 166Figure 99 - Front view of the alarm protection module (iBTS Outdoor) 167Figure 100 - Front view of the alarm protection module (iBTS Indoor) 168Figure 101 - Alarm protection cabling (iBTS Outdoor) 169Figure 102 - Alarm protection cabling (iBTS Indoor 600) 170Figure 103 - Front view of the PCM protection module (iBTS Outdoor) 171Figure 104 - PCM lightning protection cabling (iBTS Outdoor) 172Figure 105 - Front view of the LPPCM (iBTS Indoor 2) 174Figure 106 - LPPCM cabling (iBTS Indoor 2) 175Figure 107 - Front view of the PFM 176Figure 108 - Front view of User ICO module (iBTS Outdoor) 177Figure 109 - Front view of User ICO module (iBTS Street) 178Figure 110 - iDACS operation principle 181Figure 111 - iBTS Indoor cooling unit 183Figure 112 - iBTS Street air paths 186Figure 113 - ICU front view 190Figure 114 - Univity iBTS Indoor 1900 Compact airflow 192Figure 115 - CICU detailed front view 194Figure 116 - Distribution of the ac voltage within the Univity iBTS Outdoor 196Figure 117 - Front view of the single phase filtering box 197Nortel Networks Confidential List of figures xiCopyright © 2000-2003 Nortel Networks About the Univity iBTS
Figure 118 - Front view of the split-phase filtering box (US) 198Figure 119 - Front view of the split-phase filtering box 199Figure 120 - Front view of the three-phase filtering box 200Figure 121 - ac distribution module 201Figure 122 - BIP functional diagram 203Figure 123 - Front view of the BIP (Univity iBTS Indoor 2100) 204Figure 124 - Outside view of the ac plinth 205Figure 125 - Inside view of the ac plinth 206Figure 126 - ac plinth cabling (Univity iBTS Indoor 700 2100) 208Figure 127 - ac voltage distribution within the Univity iBTS Street 2100 209Figure 128 - Front view of the dc power system shelf (Univity iBTS Outdoor) 212Figure 129 - Front view of the dc power system shelf in the ac plinth (Univity iBTS Indoor2100) 212Figure 130 - Front view of the dc power system shelf (Univity iBTS Street 2100) 213Figure 131 - dc distribution rack of the Univity iBTS Outdoor 214Figure 132 - Front view of the dc distribution (Univity iBTS Outdoor) 215Figure 133 - Distribution scheme of the dc current within the Univity iBTS Street 2100 217Figure 134 - Univity iBTS Indoor 2 dc electrical distribution system 219Figure 135 - Univity iBTS Indoor 2 dc distribution scheme 220Figure 136 - electrical distribution scheme of Univity iBTS Mono (mode 1) 222Figure 137 - electrical distribution scheme of Univity iBTS Mono (mode 2) 223Figure 138 - Univity iBTS Indoor 1900 Compact distribution system 225Figure 139 - Univity iBTS Indoor 1900 dc distribution scheme 226Figure 140 - Front view of the rectifier module 228Figure 141 - Front view of the SPCM 229Figure 142 - Inside view of the external battery cabinet 234Figure 143 - +24 V dc converter kit option 236Figure 144 - iBTS protocol stacks 240Figure 145 - iBTS function mapping 241Figure 146 - Call processing on the CEM 243Figure 147 - TRM software architecture 244Figure 148 - Call processing on the TRM 245Figure 149 - OAM software architecture on the CCM 247Figure 150 - Call processing on the CCM 248Figure 151 - Data flow of the uplink path 251Figure 152 - Data flow of the downlink path 252Figure 153 - CEM physical model 254Figure 154 - iBTS external connection 259Figure 155 - Transmission between iBTS and Univity RNC by using the IMA over PCM 261Nortel Networks Confidential List of figures xiiUMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
Table 1 - Univity iBTS cabinets 17Table 2 - The digital shelf modules supported by the iBTS cabinets 82Table 3 - DDM LEDs status 143Table 4 - TMA LED Status 143Table 5 - VSWR LEDs Status (Main/Diversity) 144Nortel Networks Confidential List of tables xiiiCopyright © 2000-2003 Nortel Networks About the Univity iBTS
About this publicationThis publication deals with the Nortel Network Univity Internet Base Transceiver Station (iBTS) whichis part of the UMTS network.ApplicabilityThis publication is applicable to the UMTS03 system release.AudienceThis publication is for operations and maintenance personnel, and other users who want moreknowledge of the iBTS.PrerequisitesIt is recommended that readers also become familiar with the following documents:•About the UMTS Network (UMT/DCL/DD/0001 or 411-8111-101)•Univity iBTS Fault Analysis (UMT/DCL/DD/0006 or 411-8111-506)•Univity iBTS Hardware Maintenance Guide (UMT/DCL/DD/0005 or 411-8111-505)•About the Univity RNC (UMT/DCL/DD/0003 or 411-8111-906)How this document is organizedIn a continuous effort to improve our documentation, we are preparing its delivery through the web.This leads to a new global organization of the Nortel Networks technical publications.The information will be broken down into modules, with each module containing elementaryinformation such as the procedure to replace a particular equipment, or the description of a particularcomponent.The modules are designed in order to deliver just enough information to provide the user with thesolution required to perform his current task.These modules will usually be delivered on CD-ROMs or through the web. The user will access thisinformation by browsing, navigating from one module to another, or by using a search engine.In its current version, this NTP has been written as a series of modules. The modules are arrangedone after the other in logical order. The table of contents helps you to access the right module. Becareful, while screening the table of contents, since all the modules will be displayed with the samelevel of importance.This publication consists of the following sets of modules:• The first part describes what is new in the About the Univity iBTS publication.• The second part provides the Univity iBTS regulatory information.• The third part gives the UTRAN overview of the UMTS03 solution.• The fourth part describes the Univity iBTS configuration and architecture.• The fifth part describes the Univity iBTS interfaces• The sixth part describes the Univity iBTS hardware• the seventh part describes the Univity iBTS softwareNortel Networks Confidential 1UMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
• the last part describes the Univity iBTS services and featuresVocabulary conventionsLists of terms used in the publication are in: Terminology (UMT/DCL/DD/0004 or 411-8111-804)Safety regulationIn order to guarantee the safety of personnel and equipment it must be taken into account of thefollowing aspects general personnel safety instructions and equipment safety instructions.Caution message indicate the risk of impact on equipment.CAUTIONImpact on equipmentNortel Networks Confidential 2UMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
What is in new about the Univity iBTSThis following list details the main changes in this publication between system release UMTS03 andUMTS02 releases:Univity iBTS modulesThe new modules are the following:• DDM-2• iCEM 64 (19006)• iCEM 128 (22752)• iCCM (19845)• iCCM Redundancy (20681)• iTRM (20615)• TMA 2100 module• TMA 1900 module (22691)• NAM (19849) from the system point of view.• DDM/DDM2 1900• MCPA 1900 module• TRM/iTRM 1900 moduleUnivity iBTS cabinetsThe new Univity iBTS cabinets are the following:• Univty iBTS Mono 2100 (20600)• Univity iBTS Indoor 2 2100• Univity iBTS Outdoor 1900 (24861)• Univity iBTS Indoor 2 1900(20914)• Univity iBTS Mono 1900• Univity iBTS Indoor 1900 CompactUnivity iBTS functionalitiesThe new Univity iBTS functionalities are the following:• iModules mixity• Univity iBTS 1900 transmission (IMA+D&I) (22458)• +24 Vdc option for Univity iBTS indoor 2 1900 (21654)• +24 Vdc option for Univity iBTS indoor 1900 Compact• OTOR configuration• BTBR configuration• OTBR configuration (only for UMTS 2100)Nortel Networks Confidential 3Copyright © 2000-2003 Nortel Networks About the Univity iBTS
Nortel Networks Confidential 4UMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
Univity iBTS regulatory informationThis part which provides the regulatory information concerning the Univity iBTS is split into thefollowing items:• European regulatory requirement compliance• North American regulatory requirement compliance• Compliances for other regions/countries• Operation conditions• Cable specifications• Product labellingEuropean regulatory requirement complianceAs a radio product, the Nortel Networks UMTS iBTS falls under the requirement of the RTTE (Radioand Telecom Terminal Equipment) European directive 1999/5/EEC. The RTTE directive coversessential requirements in the field of:• protection of the Health and Safety of the user and any other person, including the objectives withrespect to safety requirements contained in the Low Voltage directive (73/23/EEC)• the protection requirements with respect to EMC contained in Directive 89/336/EEC.The equipment generates, uses, and can radiate radio frequency energy. If not installed andused in accordance with the instruction manual, the equipment may cause harmful interference toradio communications. However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio or televisionreception, which can be determined by turning the equipment off and on, the user is encouragedto try to correct the interference.The EMC requirements have been selected to ensure an adequate level of compatibility forapparatus at residential, commercial, and light industrial environments. The levels however, donot cover extreme cases which may occur in any location but with a low probability of occurrence.In particular, it may not cover those cases where a potential source of interference which isproducing individually repeated transient phenomena, or continuous phenomena, is permanentlypresent, for example a radar or broadcast site in the near vicinity. In such a case it may benecessary to either limit the source of interference, or use special protection applied, to theinterfered part, or both.Note: For operation or maintenance inside Nortel Networks systems, the antistatic wrist shallalways be used to maintain the integrity of the product.• effective use of the Radio spectrum allocated to terrestrial/space radio communication and orbitalresources so as to avoid harmful interference. The routes and standards used to demonstratecompliance with there essential requirements are outlined in the following paragraphs.—iBTS EMCCompliance with the essential requirements of EMC has been demonstrated usingEN301489-1 & -23 standard—iBTS radio complianceCompliance with the essential requirements of effective use of the radio spectrum has beendemonstrated using EN301908-1 & -3 standard.Nortel Networks Confidential 5Copyright © 2000-2003 Nortel Networks About the Univity iBTS
—iBTS safetyCompliance with the essential requirements of Safety has been demonstrated using EN60950 Standard.—iBTS health protectionCompliance with the essential requirement of health requirement has been demonstratedusing EN50385.North American regulatory requirements complianceThe Nortel Networks UMTS iBTS has been qualified according to North American marketrequirements for the Outdoor, Indoor 2, Mono, and Indoor 1900 compact versions.This equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:• reorient or relocate the receiving antenna• increase the separation between the equipment and receiver• connect the equipment into an outlet on a circuit different from that to which the receiver isconnected• consult the dealer or an experienced radio/TV technician for helpiBTS safetyNortel Network iBTS complies with UL60950 and CAN/CSA C22.2 No. 60950-00 SafetyStandards. The CSA mark is applied on the iBTS and demonstrates compliance with both USand Canadian Standards.iBTS EMC and radio complianceNortel Network iBTS complies with 47CFR Part 15 class B and 47 CFR Part 24 for EMC andradio emission limits according to US regulatory requirements as indicated on the regulatory labeliBTS interconnection complianceThe UMTS Univity iBTS complies with 47 CFR Part 68 of the FCC rules and the requirementsadopted by the ACTA.On the top right of this equipment is a label that contains, among other information, a productidentifier in the following format:•US : AB6XDNANUMTSIND for the Univity iBTS Indoor 2•US : AB6XDNANUMTSOUT for the Univity iBTS Outdoor•US : AB6XDNANUMTSMONO for the Univity iBTS Mono•US: AB6XDNANUMTSCOMP for the Univity iBTS Indoor CompactNortel Networks Confidential 6UMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
If requested, the following information must be provided to the telephone company:• FCC Registered Number: AB6• Facility Interface Code (FIC): 04DU9.BN, 04DU9.DN, 04DU9.1KN, and 04DU9.1SN• Service Order Code (SOC): 6.0FA FCC part 68 and ACTA compliant cable is provided with the Univity iBTS equipment, with noconnector at network interface side. The Univity iBTS equipment operates with a 1.544 Mbpsdigital channel. See Installation Instructions for details.If the Univity UMTS iBTS equipment causes harm to the phone network, the telephone companywill notify you in advance that temporary discontinuance of service may be required. But ifadvance notice is not practical, the telephone company will notify the customer as soon aspossible. Also, you will be advised of your right to file a complaint with the FCC if you believe it isnecessaryThe telephone company may make changes to its facilities, equipment, operations or proceduresthat could affect the operation of the equipment. If this happens the telephone company willprovide advance notice so you can make the necessary modifications to maintain uninterruptedservices.If trouble is experienced with Univity UMTS iBTS equipment, for repair or warranty information,please contact Toy-Brent LoranceNortel NetworksPhone: 972-685-2270Fax: 972-684-7601NortelNetworks 1334 Enterprise Drive, West Chester PA, 19380.If the equipment is causing harm to the telephone network, the telephone company may requestthat you disconnect the equipment until the problem is resolved.All repairs should be handled by authorized Nortel Networks Service Personnel.Univity iBTS data equipmentThe following table shows which jacks are associated with which modes of operation.Operation Mode USOC JackProgrammable & Test RJ45SUnivity iBTS systemsFacility Interface Codes (FIC), Services Order Codes (SOC), USOC Jack Codes, and RingerEquivalence Number (REN) are shown in the table below for each port where applicable.Port FIC SOC USOC Jack RENCCM T1 board 04DU9.BN 6.0F N/A N/ACCM T1 board 04DU9.DN 6.0F N/A N/ACCM T1 board 04DU9.1KN 6.0F N/A N/ACCM T1 board 04DU9.1SN 6.0F N/A N/AiCCM T1 board 04DU9.BN 6.0F N/A N/AiCCM T1 board 04DU9.DN 6.0F N/A N/AiCCM T1 board 04DU9.1KN 6.0F N/A N/AiCCM T1 board 04DU9.1SN 6.0F N/A N/ANortel Networks Confidential 7Copyright © 2000-2003 Nortel Networks About the Univity iBTS
iBTS RF health protectionCompliance with the North American requirements is demonstrated through calculation accordingto FCC OET bulletin 65.Compliances for other regions/countriesFor countries outside Europe and the Americas, the requirements of European countries usuallyapply.It is not possible to list all the applicable approvals / compliances as they will be dependent on themarkets and products considered.Note: Please contact your local Nortel Networks representative for more information.Operational conditionsThe aforementioned standards compliance of the products are based on the following operatingconditions (called normal operation):• doors shall be closed and/or covers shall be in place• external cables shall be of the same type as specified by Nortel Networks• no modification of any mechanical or electrical characteristics of the product shall be madeAny change or modification made to the product without written approval from Nortel Networksreleases Nortel Networks from subsequent responsibility regarding the standards compliance.Cable specificationsThe compliance to the aforementioned standards has been verified using cables as specified byNortel Networks. The continuing compliance of the product relies upon use of the correct cablingscheme as well as use of identical type cables as specified by Nortel Networks. Refer to theinstallation guides for details on cable specifications.Product labelingThe label may be located inside or outside the product, provided that the operation and/ormaintenance personnel have the information when working on the product.iBTS labeling for American CountriesTo indicate compliance with the CSA and UL Safety requirements, the Nortel Networks UMTSiBTS bears the following mark in a conspicuous location.On the regulatory label, compliance to 47 CFR Part 15, 24 and 68 is stated along with:Nortel Networks Confidential 8UMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
• FCC ID, FCC Registration Number• Manufacturers name• Equipment designation• Nominal voltage operating range and maximum rated current.iBTS labelling for European CountriesTo indicate compliance with the European RTTE Directive, the Nortel Networks UMTS iBTSbears the following information in a conspicuous location:• Manufacturers name• Equipment designation• Nominal voltage operating range and maximum rated currentLabeling for other regions / countriesLabeling for other regions and countries is performed as appropriate and required by the localregulatory framework.Nortel Networks Confidential 9Copyright © 2000-2003 Nortel Networks About the Univity iBTS
UTRAN introduction of the UMTS03 solutionThe Nortel Networks UTRAN is based on:• the Univity RNC• the Univity iBTS• the NAM, optionally for transmission purposeUnivity RNCThe Univity RNC is the Nortel Networks Univity UMTS RNC. It is the 3GPP-compliant UMTS RNCdeveloped by Nortel Networks.The Univity RNC allows mobility between UMTS and GSM networks.The main functions of the Univity RNC are to control and manage the following:• the Radio Access Network (RAN)• the signaling between the different Core Network (CN) components and the Radio NetworkSystem (RNS)• the Node Bs and their corresponding radio resourcesThe Univity RNC is connected to:• Univity iBTSs through the Iub interface• another Univity RNC through the Iur interface.In fact an RNC can be connected to several other RNCs via Iur.• the Core Network through the Iu interfaceMost of the Univity RNC interfaces provide the ability to build multi-vendor solutions. The main part ofthe Univity RNC is built upon the Passport technology.The Univity RNC supports the UMTS 1900 MHz and the UMTS 2100 MHz frequencies.Univity RNC configurations for UMTS 1900The RNC supports UMTS 1900 MHz configurations to provide the SONET/OC-3 transmissioninterfaces. The SONET/OC-3 mode is supported for the Iu, Iub, Iur interfaces.Univity RNC configurations for UMTS 2100The RNC supports UMTS 2100 MHz configurations to provide the SDH/STM-1 transmissioninterfaces. The SDH/STM-1 mode is supported for the Iu, Iub, Iur interfaces.Univity iBTSThe Univity iBTS is the 3GPP-compliant UMTS Node B developed by Nortel Networks. The genericterm iBTS is used to designate the Univity UMTS Internet Base Transceiver Station.The Univity iBTS supports the following functions:• network interface management— Iub towards the Univity RNC— Uu towards the UENortel Networks Confidential 10UMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
• radio access and modem (modulation/demodulation, frequency up/down-conversion,amplification)• call processing (channel setup and management for both common and dedicated channels, cellmanagement, power control, handover and measurement)• configuration and supervision• synchronization• performance monitoringNAMThe NAM improves the switching/routing capabilities of the Univity iBTS.It provides the following features:• HubThe NAM can implement a hubbing function for the Node Bs. It allows to minimize the number ofT1/E1 links, between Node Bs and a RNC.• Cell aggregationIt concentrates the traffic of different Node Bs before transmission on the Iub interface.• Fractional E1/T1 to achieve Drop&Insert UMTS-UMTS and GSM-UMTS.The NAM is built on the Passport 7420 equipment.UTRAN architecture examples of the UMTS03 solutionUTRAN architecture examples of the UMTS03 solution are shown in the following figures. They aresplit into:• UMTS 1900: for a SONET configuration• UMTS 2100: for a SDH and a PCM configurationFigure 1 UTRAN architecture example of the UMTS03 solution (1900 MHz—SONET)Nortel Networks Confidential 11Copyright © 2000-2003 Nortel Networks About the Univity iBTS
Figure 2 UTRAN architecture example of the UMTS03 solution (2100 MHz —SDH)Nortel Networks Confidential 12UMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
Figure 3 UTRAN architecture example of the UMTS03 solution (2100 MHz —PCM)Nortel Networks Confidential 13Copyright © 2000-2003 Nortel Networks About the Univity iBTS
Univity iBTS basic characteristicsThis part describing the basic characteristics of the Univity iBTS is split into the following:• Univity iBTS introduction• Univity iBTS key featuresNortel Networks Confidential 14UMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
Univity iBTS introductionA NodeB supports Frequency Division Duplex (FDD) mode, Time Division Duplex (TDD) mode ordual-mode operation.The 3GPP-compliant UMTS base station developed by Nortel Networks is named Univity iBTS. TheUnivity iBTS supports only the FDD mode and it provides Outdoor and indoor deployment to coverdifferent customer requirements.This section provides an overview of Nortel Network Univity iBTS.The Univity iBTS is responsible for radio transmission/reception in one or more cells to/from the UE(User Equipment).The iBTS provides:• the means of communication between a User Equipment (UE) and a network via TransportChannels• physical layer channels which are necessary to synchronize the downlink and also to perform cellselection/reselection and hand over preparation• measurement information to the Univity RNC for radio resource management (hand over, powercontrol)The Univity iBTS provides up to eight E1/T1 with IMA (Inversion Multiplexing ATM) or to Drop andInsert a fractional E1/T1.Univity iBTS interfacesThe iBTS provides the following interfaces:• Uu interface (UMTS User interface): this interface is used between the iBTS (internet BaseTransceiver Station) and the UE (User Equipment). It is dependent on the technology used onthe radio (for example, it can be W-CDMA or TD/CDMA)• Iub interface (Interface UMTS iBTS): this interface lies between the Univity RNC and the iBTS. Itallows to connect Univity RNCs (internet Radio Network Controller).Univity iBTS cabinetsNortel Networks provides the following iBTS cabinet types:• Univity iBTS Outdoor 2100The iBTS Outdoor 2100 is a single cabinet closed by two doors.The iBTS Outdoor 2100 is designed to optimize deployment in rural area, suburban area, urbanarea, highway, and rooftop.• Univity iBTS Outdoor 1900The iBTS Outdoor 1900 is a single cabinet closed by two doors.The iBTS Outdoor 1900 is only the 1900 MHz version of the Univity iBTS Outdoor 2100, whichmakes it compatible with the North-American standard.• Univity iBTSs Indoor 2100The Univity iBTS Indoor is a single 600mm-wide cabinet (Univity iBTS Indoor 600) or a single700mm-wide cabinet (Univity iBTS Indoor 700) closed by two doors. It is installed inside if an airNortel Networks Confidential 15Copyright © 2000-2003 Nortel Networks About the Univity iBTS
exchanger is provided.The Univity iBTS Indoor 2100 is also designed to optimize deployment in rural area, sub-urbanarea, urban area, highway, and rooftop.• Univity iBTS Street 2100The Univity iBTS Street 2100 is a single cabinet closed by two doors.The Univity iBTS Street 2100 is designed to optimize deployment in city, urban, and sub-urbanareas: city street corner, public sidewalks, parking areas, and motorways.• Univity iBTS Indoor 2 2100The Univity iBTS Indoor 2 2100 is a single cabinet closed by one door. It is designed for ease ofmanufacture, transportation, installation, system assembly, repair and testing.The iBTS Indoor 2 2100 is installed inside if an air exchanger is provided.The iBTS Indoor 2 2100 is an evolution of iBTS Indoor 600 to improve mechanical, acousticperformances on the equipment.• Univity iBTS Indoor 2 1900The Univity iBTS Indoor 2 1900 is a single cabinet closed by one door. It is designed for ease ofmanufacture, transportation, installation, system assembly, repair and testing.The iBTS Indoor 2 1900 is installed inside if an air exchanger is provided.The Univity iBTS Indoor 2 1900 is a new version of the Univity iBTS Indoor 2 2100, which makesit compatible with the North-American standard. There is no specific evolution, excepted thesupport of the module needed for the 1900 MHz frequency.• Univity iBTS Mono 2100the Univity iBTS Mono 2100 is a single cabinet closed by one door.The Univity iBTS Mono 2100 is designed to be installed on walls or poles. It is also designed toprovide minimum visual impact while maintaining the highest Radio Frequency (RF) performancefor a mono carrier UMTS product. Its compact dimensions allow easy and flexible installation inoutdoor areas.• Univity iBTS Mono 1900The Univity iBTS Mono 1900 is a new version of the Univity iBTS Mono 2100, which makes itcompatible with the North-American standard. There is no specific evolution, excepted thesupport of the module needed for the 1900 MHz frequency.• Univity iBTS Indoor 1900 Compactthe Univity iBTS Indoor 1900 Compact is a single cabinet closed by one door.The Univity iBTS Compact provides the an attractive solution for restricted site space, particularlyin urban and sub-urban environments. It can fit in standard racks or even on tabletops.The Univity iBTS Indoor 1900 Compact compatible with the North-American standard.The Macro iBTS term is used to indicate the set of iBTS cabinets (Univity iBTS Outdoor, Univity iBTSIndoor 700, Univity iBTS Indoor 600, and Univity iBTS Indoor 2).The Macro iBTS is modular in design for easy network growth and flexibility, to manage diversetraffic demands. Common modules are used to grow the iBTS to increase capacity as required. TheNortel Networks Confidential 16UMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
increase in capacity is provided via the simple addition of modules, as opposed to the addition entireof cabinets.The following table lists the Univity iBTS cabinets according to the UMTS standard (UMTS 2100 andUMTS 1900).Table 1 Univity iBTS cabinetsTypes UMTS 2100 UMTS 1900Univity iBTS Outdoor X XUnivity iBTS Indoor 2100(600/700) X NAUnivity iBTS Indoor 2 X XUnivity iBTS Mono X XUnivity iBTS Street 2100 X NAUnivity iBTS Indoor 1900 Com-pact NA XThe following figure shows the iBTS types provide by Nortel Networks:Nortel Networks Confidential 17Copyright © 2000-2003 Nortel Networks About the Univity iBTS
Figure 4 Univity iBTS Outdoor outside viewNortel Networks Confidential 18UMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
Figure 5 Univity iBTS Indoor 2100 outside viewNortel Networks Confidential 19Copyright © 2000-2003 Nortel Networks About the Univity iBTS
Figure 6 Univity iBTS Street 2100 outside viewNortel Networks Confidential 20UMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
Figure 7 Univity iBTS Indoor 2 outside viewNortel Networks Confidential 21Copyright © 2000-2003 Nortel Networks About the Univity iBTS
Figure 8 Univity iBTS Mono outside viewNortel Networks Confidential 22UMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
Figure 9 Univity iBTS Indoor 1900 Compact outside viewUnivity iBTS modulesIn the first generation, Nortel Networks delivers the modules-alpha. These modules are supported byall the iBTSs (Macro iBTS, Univity iBTS Mono, Univity iBTS Indoor 1900 Compact, and Univity iBTSStreet 2100).In the second generation (UMTS03 system release), Nortel Networks delivers the iModules (calledalso modules-beta). These modules are supported by all the iBTSs (Macro iBTS, Univity iBTS Mono,Univity iBTS Indoor 1900 Compact, and Univity iBTS Street 2100) and are compatible with existingones. These new modules are transparent to you as they do not provide a capacity change (exceptfor the iCEM).Nortel Networks Confidential 23Copyright © 2000-2003 Nortel Networks About the Univity iBTS
Univity iBTS key featuresThis section describes the general features of the iBTS.iBTS featuresThe iBTS includes the following features:• outdoor operation• indoor operation• ac operation (iBTS Outdoor, iBTS Street, and iBTS Indoor 700) or dc operation (iBTS Indoor 600,iBTS Indoor 2, iBTS Mono, and iBTS Indoor 1900 Compact)• digital system support of up to three carriers• front access only• plug and play• PCM internal protection• multiple CEM• multiple PCM• no need for an extra site cabinet for user space and batteries• best-in-class in term of volume and size• easy installation and commissioning• maintenance facilities: modular design, hardware and software diagnostics for fault isolationmechanism and fast reconfiguration• most commonly shared modules between the iBTS different types• software upgrade with minimum service downtime• a flexible product: possible growth from low to high capacity without any additional cabinets• drop and insert• STSR1 configuration• BTBR1 configuration• STSR2 configuration• BTBR2 configuration• OTSR1 configuration• OTBR1 configuration• OTOR1 configuration• OTOR2 configuration• Network Access Module (NAM)• iCEM, iCCM, and iTRM modules• iCCM redundancyNortel Networks Confidential 24UMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
Nortel Networks Confidential 25Copyright © 2000-2003 Nortel Networks About the Univity iBTS
Univity iBTS characteristicsThis section details the characteristics (frequency bands, physical, electrical, thermal and acoustic) ofthe iBTS cabinet types.Univity iBTS OutdoorThe characteristics of the Univity iBTS Outdoor are the following:• frequency bands 2100 MHz:— 2110-2170 MHz for downlink— 1920-1980 MHz for uplink• frequency bands 1900 MHz:— 1930-1990 MHz for downlink— 1850-1910 MHz for uplink• optimized size versus capacity ratio:— footprint: 0.95 m²— cabinet size is the following:– width (W): 1350 mm– depth (D): 700 mm– height (H): 1300 mm— Volume: 1240 l• ac Power:— Single/Split: 20 A/phase— three phase: 10 A/phase (balanced)• operation Temperature Range: -40 to +50 degree Celsius• weight:— fully equipped: 520 kg— empty: 180 kg• acoustic: about 44 dBA at 5 feetUnivity iBTS Indoor 600The characteristics of the Univity iBTS Indoor 600 are the following:• frequency bands 2100 MHz:— 2110-2170 MHz for downlink— 1920-1980 MHz for uplink• optimized size versus capacity ratio:— footprint: 0.615 m²— cabinet size is the following:Nortel Networks Confidential 26UMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
– width (W): 600 mm– depth (D): 600 mm– height (H): 1600 mm— volume: 576 L• dc Power: -48 V dc• operation Temperature Range: -5 to +50 degree Celsius• weight:— fully equipped: 560 kg— empty: 105 kgUnivity iBTS Indoor 700 without ac power plinthThe characteristics of the Univity iBTS Indoor 700 are the following:• frequency bands 2100 MHz:— 2110-2170 MHz for downlink— 1920-1980 MHz for uplink• Optimized size versus capacity ratio:— footprint: 0.7525 m²— cabinet size is the following:– width (W): 700 mm– depth (D): 600 mm– height (H): 1600 mm— volume: 672 l• dc Power: -48 V dc• operation Temperature Range:— long term: 5 to +40 degree Celsius— short term: -5 to +50 degree Celsius• weight:— fully equipped: 325.5 kg— empty: 128.5 kgUnivity iBTS Indoor 700 with ac power plinthThe characteristics of the Univity iBTS Indoor 700 with ac power plinth are the following:• frequency bands 2100 MHz:— 2110-2170 MHz for downlink— 1920-1980 MHz for uplinkNortel Networks Confidential 27Copyright © 2000-2003 Nortel Networks About the Univity iBTS
• optimized size versus capacity ratio:— footprint: 0.7525 m²— cabinet size is the following:– Width (W): 700 mm– Depth (D): 600 mm– Height (H): 2000 mm— Volume: 672 l• dc Power: -5 V dc and +24 V dc• ac Power:— Single/Split: 20 A/phase— three phase: 10 A/phase (balanced)• operation Temperature Range:— long term: 5 to +40 degree Celsius— short term: -5 to +50 degree Celsius• weight:— fully equipped: 513.5 kg— empty: 128.5 kg— ac Plinth: 170 kgUnivity iBTS Street 2100The characteristics of the Univity iBTS Street are the following:• frequency bands 2100 MHz:— 2110-2170 MHz for downlink— 1920-1980 MHz for uplink• optimized size versus capacity ratio:— footprint: 0.52 m²— cabinet size is the following:– width (W): 1480 mm– depth (D): 350 mm– height (H): 1500 mm— volume: 761.25 l• ac power is following:— Single/Split: 120/240 V ac— three phase: 120/208 V ac or 240/416 V ac• operation Temperature Range: -40 to +45 degree CelsiusNortel Networks Confidential 28UMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
• weight:— fully equipped: 321 kg— empty: 180 kg• acoustic: about 47 dBA between -20 and +40 degree CelsiusUnivity iBTS Indoor 2The characteristics of the Univity iBTS Indoor 2 are the following:• frequency bands 2100 MHz:— 2110-2170 MHz for downlink— 1920-1980 MHz for uplink• frequency bands 1900 MHz:— 1930-1990 MHz for downlink— 1850-1910 MHz for uplink• optimized size versus capacity ratio:— cabinet size is the following:– width (W): 600 mm– depth (D): 600 mm– height (H): 1650 mm— volume: 594 L• dc Power: -48 V dc (2100)• dc Power: + 24 V dc (1900) by using the +24 V dc converter kit option• operation Temperature Range:— long term: +5 to +45 degree Celsius— short term: -5 to +45 degree Celsius• weight:— empty: 140 kg— fully equipped: 305 kgUnivity iBTS MonoThe characteristics of the Univity iBTS Mono are the following:• frequency bands 2100 MHz:— 2110-2170 MHz for downlink— 1920-1980 MHz for uplink• frequency bands 1900 MHz:— 1930-1990 MHz for downlink— 1850-1910 MHz for uplinkNortel Networks Confidential 29Copyright © 2000-2003 Nortel Networks About the Univity iBTS
• optimized size versus capacity ratio:— cabinet size is the following:– width (W): 460 mm– depth (D): 570 mm– height (H): 600 mm— volume: 157,32 L• dc power: -48 V dc• single phase: 220 V ac• operation Temperature Range: -20 to +45 degree Celsius• weight < 90 kg• single configuration: 1 sector and 1 carrier• receive diversityThe iBTS Mono does not support the following:• external alarms• battery backup• CCM redundancy• Tx diversity• +24VdcThe iBTS Mono supports the following options:• Tower Masterhead Amplifiers (TMA)• Lightening protection• Fractional E1/T1 which is shared with GSM BTSUnivity iBTS Indoor 1900 CompactThe characteristics of the Univity iBTS Indoor 1900 Compact are the following:• frequency bands 1900 MHz:— 1930-1990 MHz for downlink— 1850-1910 MHz for uplink• optimized size versus capacity ratio:— cabinet size is the following:– width (W): 483 mm– depth (D): 650 mm– height (H): 900 mm— volume: 282 L• dc power: -48 V dcNortel Networks Confidential 30UMT/DCL/DD/0002 03.09/EN Preliminary October 2003 Copyright © 2000-2003 Nortel Networks411–8111–905
• single/split phase: 120/240 V ac• operation Temperature Range: -5 to +45 degree Celsius• weight < 63kg• the configurations supported are the following:— OTOR1/OTOR2 configuration— STSR1/STSR2 configuration with MCPAs 45W— BTBR1/BTBR2 configuration with MCPAs 45W• receive diversityThe Univity iBTS Indoor 1900 Compact does not support the following:• external or internal battery• O2 configuration• CCM redundancy• Tx diversityThe Univity iBTS Indoor 1900 Compact supports the following options:• Tower Masterhead Amplifiers (TMA)• Lightening protection• Fractional E1/T1 which is shared with GSM BTS• +24VdcNortel Networks Confidential 31Copyright © 2000-2003 Nortel Networks About the Univity iBTS

Navigation menu