Avaya Serial Adapter Module Supplement Users Manual Jan 99,

: Avaya Avaya-Serial-Adapter-Module-Supplement-Users-Manual-734619 avaya-serial-adapter-module-supplement-users-manual-734619 avaya pdf

Open the PDF directly: View PDF .
Page Count: 10

Part No. 303124-A Rev 01

November 1998

*303124-A Rev 01*

Serial Adapter Module

Supplement

ii 303124-A Rev 01

4401 Great America Parkway 8 Federal Street

Santa Clara, CA 95054 Billerica, MA 01821

Copyright © 1998 Bay Networks, Inc.

All rights reserved. Printed in the USA. November 1998.

The information in this document is subject to change without notice. The statements, configurations, technical data,

and recommendations in this document are believed to be accurate and reliable, but are presented without express or

implied warranty. Users must take full responsibility for their applications of any products specified in this document.

The information in this document is proprietary to Bay Networks, Inc.

Trademarks

AN, Optivity, Quick2Config and Bay Networks are registered trademarks and Advanced Remote Node, ANH, ARN,

BayRS, BayStack, BCC, and the Bay Networks logo are trademarks of Bay Networks, Inc.

All other trademarks and registered trademarks are the property of their respective owners.

Statement of Conditions

In the interest of improving internal design, operational function, and/or reliability, Bay Networks, Inc. reserves the

right to make changes to the products described in this document without notice.

Bay Networks, Inc. does not assume any liability that may occur due to the use or application of the product(s) or

circuit layout(s) described herein.

USA Requirements Only

Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio

frequency energy. If it is not installed and used in accordance with the instruction manual, it may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference, in which case users will be required to take whatever measures may be necessary to correct the

interference at their own expense.

European Requirements Only

EN 55 022 Statement

This is to certify that the Bay Networks <product or system name> is shielded against the generation of radio

interference in accordance with the application of Council Directive 89/336/EEC, Article 4a. Conformity is declared

by the application of EN 55 022 Class A (CISPR 22).

Warning: This is a Class A product. In a domestic environment, this product may cause radio interference, in which

case, the user may be required to take appropriate measures.

EC Declaration of Conformity

This product conforms (or these products conform) to the provisions of Council Directive 89/336/EEC and

73/23/EEC. The Declaration of Conformity is available on the Bay Networks World Wide Web site at

www.baynetworks.com.

303124-A Rev 01 iii

Japan/Nippon Requirements Only

Voluntary Control Council for Interference (VCCI) Statement

Voluntary Control Council for Interference (VCCI) Statement

This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information

Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise.

When such trouble occurs, the user may be required to take corrective actions.

Canada Requirements Only

Canadian Department of Communications Radio Interference Regulations

This digital apparatus (<product or system name>) does not exceed the Class A limits for radio-noise emissions from

digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications.

Règlement sur le brouillage radioélectrique du ministère des Communications

Cet appareil numérique (<product or system name>) respecte les limites de bruits radioélectriques visant les appareils

numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du ministère des

Communications du Canada.

Canada CS-03 Rules and Regulations

Notice: The Industry Canada label identifies certified equipment. This certification means that the equipment meets

telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal

Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to

the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local

telecommunications company. The equipment must also be installed using an acceptable method of connection. The

customer should be aware that compliance with the above conditions may not prevent the degradation of service in

some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or

alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications

company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines

and internal metallic water pipe system, if present, are connected together. This precaution may be particularly

important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric

inspection authority, or electrician, as appropriate.

iv 303124-A Rev 01

Notice: For equipment using loopstart lines, please note that the Ringer Equivalence Number (REN) assigned to each

terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone

interface. The termination on an interface may consist of any combination of devices subject only to the requirement

that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. The REN is located on the “FCC

Rules Part 68” label located on the bracket of the module, or on the back of the unit.

Canada CS-03 -- Règles et règlements

Avis: L'étiquette d'Industrie Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est

conforme aux normes de protection, d'exploitation et de sécurité des réseaux de télécommunications, comme le

prescrivent les documents concernant les exigences techniques relatives au matériel terminal. Le Ministère n'assure

toutefois pas que le matériel fonctionnera à la satisfaction de l'utilisateur.

Avant d'installer ce matériel, l'utilisateur doit s'assurer qu'il est permis de le raccorder aux installations de l'entreprise

locale de télécommunication. Le matériel doit également être installé en suivant une méthode acceptée de

raccordement. L'abonné ne doit pas oublier qu'il est possible que la conformité aux conditions énoncées ci-dessus

n'empêche pas la dégradation du service dans certaines situations.

Les réparations de matériel homologué doivent être coordonnées par un représentant désigné par le fournisseur.

L'entreprise de télécommunications peut demander à l'utilisateur de débrancher un appareil à la suite de réparations ou

de modifications effectuées par l'utilisateur ou à cause de mauvais fonctionnement.

Pour sa propre protection, l'utilisateur doit s'assurer que tous les fils de mise à la terre de la source d'énergie électrique,

des lignes téléphoniques et des canalisations d'eau métalliques, s'il y en a, sont raccordés ensemble. Cette précaution

est particulièrement importante dans les régions rurales.

Avertissement: L'utilisateur ne doit pas tenter de faire ces raccordements lui-même; il doit avoir recours à un service

d'inspection des installations électriques, ou à un électricien, selon le cas.

Avis: Veuillez prendre note que pour tout appareillage supportant des lignes de type “loopstart,” l'indice d'équivalence

de la sonnerie (IES) assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être

raccordés à une interface. La terminaison d'une interface téléphonique peut consister en une combinaison de quelques

dispositifs, à la seule condition que la somme d'indices d'équivalence de la sonnerie de tous les dispositifs n'excède pas

5. Le REN figure sur l’étiquette “FCC Rules Part 68” située sur le support du module ou à l’arrière de l’unité.

FCC Part 68 Compliance Statement

This equipment complies with Part 68 of FCC Rules. All direct connections to telephone network lines must be made

using standard plugs and jacks compliant with FCC Part 68. Please note the following:

1. You are required to request service from the telephone company before you connect the unit to a network. When

you request service, you must provide the telephone company with the following data:

• When you request T1 Service, you must provide the telephone company with

-- The Facility Interface Code

Provide the telephone company with all the codes below:

- 04DU9-BN (1.544 MB, D4 framing format)

- 04DU9-DN (1.544 MB, D4 framing format with B8ZF coding)

- 04DU9-1KN (1.544 MB, ESF framing format)

- 04DU9-1SN (1.544 MB, ESF framing format with B8ZF coding)

- 04DU9-1ZN (1.544 MB, ANSI ESF and ZBTSI without line power)

The telephone company will select the code it has available.

-- The Service Order Code(s) (SOC): 6.0F

-- The required Universal Service Order Code (USOC) jack: RJ48C

303124-A Rev 01 v

• When you request 56K/64K Service, you must provide the telephone company with

-- The Facility Interface Code: 04DU5-56/64

-- The Service Order Code(s) (SOC): 6.0F

-- The required Universal Service Order Code (USOC) jack: RJ48S

• When you request V.34 Service, you must provide the telephone company with

-- The required Universal Service Order Code (USOC) jack: RJ11C

-- The make, model number, Ringer Equivalence Number (REN), and FCC Registration number of the

unit

The REN helps you determine the number of devices you can connect to your telephone line and still have

all of those devices ring when your number is called. In most, but not all, areas, the sum of the RENs of all

devices should not exceed 5.0. To be certain of the number of devices you can connect to your line, you

should call your local telephone company to determine the maximum REN for your calling area.

This equipment must not be used on party lines or coin lines.

• When you request ISDN “U” Interface Service, you must provide the telephone company with

-- The Facility Interface Code: 02IS5

-- The Service Order Code(s) (SOC): 6.0F

-- The required Universal Service Order Code (USOC) jack: RJ49C

• When you request ISDN “S/T” Interface Service, you must provide the telephone company with

-- The Service Order Code(s) (SOC): 6.0N

-- The make, model number, and FCC Registration number of the NT1

Note: ISDN S/T cannot be directly connected to the network.

• When you request Primary Rate ISDN Service, you must provide the telephone company with

-- The Facility Interface Code: 04DU9-1SN (1.544 MB, ESF framing format with B8ZF coding)

-- The Service Order Code(s) (SOC): 6.0F

-- The required Universal Service Order Code (USOC) jack: RJ48C

2. Your telephone company may make changes to its facilities, equipment, operations, or procedures that could

affect the proper functioning of your equipment. The telephone company will notify you in advance of such

changes to give you an opportunity to maintain uninterrupted telephone service.

3. If the unit causes harm to the telephone network, the telephone company may temporarily discontinue your

service. If possible, they will notify you in advance, but if advance notice is not practical, you will be notified as

soon as possible and will be informed of your right to file a complaint with the FCC.

4. If you experience trouble with the unit, please contact the Bay Networks Technical Solutions Center in your area

for service or repairs. Repairs should be performed only by service personnel authorized by Bay Networks, Inc.

United States 1-800-2LAN-WAN

Valbonne, France 33-4-92-96-69-68

Sydney, Australia 61-2-9927-8800

Tokyo, Japan 81-3-5402-0180

5. You are required to notify the telephone company when you disconnect the unit from the network.

303124-A Rev 01 1

Using the Serial Adapter Module

This document supplements one of the following guides:

• Installing an Adapter Module in a BayStack AN or ANH Router

•Installing and Operating BayStack ARN Routers (Chapter 4, “Installing a

WAN Adapter Module”)

Follow the hardware installation steps in the guide for your router, referring to this

document for information specific to the ARN™ Serial and AN®/ANH™ Third

Synchronous adapter module. Information in this supplement includes:

•“Verifying Router Requirements” on page 1

•“Attaching Cables” on page 2

•“Completing Software Configuration” on page 4

•“Interpreting LEDs” on page 4

Verifying Router Requirements

Table 1 shows the minimum versions of boot and diagnostic programmable

read-only memory (PROM) code required for a serial adapter module.

For information on upgrading PROM, see the BayRS™ Upgrading Routers guide.

Table 1. PROM Diagnostic and Boot Code for Serial Adapter Module

Router Type Code Type Minimum Version Directory File Name

ARN Boot 1.17 arn_proms arnboot.exe

Diagnostic 1.30 arn_proms arndiag.exe

AN/ANH Boot 8.12 an_proms anboot.exe

Diagnostic 5.31 an_proms andiag.exe

Serial Adapter Module Supplement

2303124-A Rev 01

Attaching Cables

Connect the communications cable to the 44-pin DSUB connector on the installed

adapter module.

You install the Serial adapter module in an open adapter module slot on the router,

as follows:

• ARN -- one of the two front-panel WAN adapter module slots (Figure 1).

See Installing and Operating BayStack ARN Routers.

• AN or 12-port ANH -- the back-panel adapter module slot (Figure 2).

See Installing an Adapter Module in a BayStack AN or ANH Router.

• 8-port ANH -- the back-panel COM3 slot (Figure 3).

See Installing an Adapter Module in a BayStack AN or ANH Router.

Figure 1. ARN Serial Adapter Module Connector (Slot 2)

To

RS-232,

RS-422,

RS-530,

V.28,

V.35,

or X.21

interface

COM

UD

DD

B1

B2

RLSD

ISDN BRI

withNT1

1

2

Tx

Rx

Cl

Tx

Rx

Cl

10BaseT

Ethernet 1

10BaseT

Ethernet 2

ARN0066A

ARN front panel

Using the Serial Adapter Module

303124-A Rev 01 3

Figure 2. Serial Adapter Module Connector on an AN or 12-Port ANH

Figure 3. Serial Adapter Module Connector on an 8-Port ANH

COM 1

CO M 2

CONSOLE

TX

RX

CL

UTP

100-240V

50-60 Hz

1.0-0.5A

XCVR

RLSD1

RLSD2

RST

L

U

U

L

Third synchronous

interface ANH0133A

COM 1

COM 2

COM 3/Expansion

Third synchronous

interface ANH137A

Serial Adapter Module Supplement

4303124-A Rev 01

Completing Software Configuration

Once you have successfully installed the Serial adapter module, complete the

following software configuration tasks using instructions found in your BayRS

documentation:

For the latest information, be sure to review the Release Notes and Documentation

Changes for your version of BayRS software.

Interpreting LEDs

The Serial adapter module RLSD (Received Line Signal Detection) LED lights

when the serial interface detects data transfer.

The LED will blink on and off during diagnostic testing, but does not indicate data

transfer until you have configured and enabled the software services.

Configuration Task Location of Instructions

Connect the ARN to the network. One of the following:

• Installing and Operating BayStack AN

and ANH Routers

• Installing and Operating BayStack ARN

Routers

• Configuring BayStack Remote Access

Modify the ARN configuration file to add the

Serial adapter module and enable default

software services.

Any of the following:

• Configuring and Managing Routers with

Site Manager

• Using the Bay Command Console

• Configuring Your Router Using the

Quick2Config Tool

Configure line services.

Configuring WAN Line Services

Configure WAN protocol services. Any of the BayRS WAN or System Suite

guides, including:

• Configuring IP Services

• Configuring Frame Relay Services

• Configuring X.25 Services

• Configuring PPP Services