Avaya S8700 Installing And Configuring The Server User Manual To 06201bea 1be4 442b 9a20 C45c830d144a

User Manual: Avaya S8700 to the manual

Open the PDF directly: View PDF .
Page Count: 104

Download
Open PDF In Browser	View PDF

Installing and Configuring the
Avaya S8700-Series Server
Release 5.0

03-300145
Release 5.0
January 2008
Issue 7

© 2008 Avaya Inc.
All Rights Reserved.
Notice
While reasonable efforts were made to ensure that the information in this
document was complete and accurate at the time of printing, Avaya Inc. can
assume no liability for any errors. Changes and corrections to the information
in this document may be incorporated in future releases.
For full legal page information, please see the documents,
Avaya Support Notices for Software Documentation, 03-600758, and
Avaya Support Notices for Hardware Documentation, 03-600759.
These documents can be accessed on the documentation CD and on the Web
site, http://www.avaya.com/support. On the Web site, search for the document
number in the Search box.
Documentation disclaimer
Avaya Inc. is not responsible for any modifications, additions, or deletions to
the original published version of this documentation unless such modifications,
additions, or deletions were performed by Avaya. Customer and/or End User
agree to indemnify and hold harmless Avaya, Avaya's agents, servants and
employees against all claims, lawsuits, demands and judgments arising out of,
or in connection with, subsequent modifications, additions or deletions to this
documentation to the extent made by the Customer or End User.
Link disclaimer
Avaya Inc. is not responsible for the contents or reliability of any linked Web
sites referenced elsewhere within this documentation, and Avaya does not
necessarily endorse the products, services, or information described or offered
within them. We cannot guarantee that these links will work all of the time and
we have no control over the availability of the linked pages.
Warranty
Avaya Inc. provides a limited warranty on this product. Refer to your sales
agreement to establish the terms of the limited warranty. In addition, Avaya’s
standard warranty language, as well as information regarding support for this
product, while under warranty, is available through the following Web site:
http://www.avaya.com/support.
Copyright
Except where expressly stated otherwise, the Product is protected by copyright
and other laws respecting proprietary rights. Unauthorized reproduction,
transfer, and or use can be a criminal, as well as a civil, offense under the
applicable law.
Avaya support
Avaya provides a telephone number for you to use to report problems or to ask
questions about your product. The support telephone number
is 1-800-242-2121 in the United States. For additional support telephone
numbers, see the Avaya Web site: http://www.avaya.com/support.

Contents

Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .

Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

How to use Avaya installation documents

. . . . . . . . . . . . . . . . . . . . .

Pre-installation requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PNC license settings for S8700-series Servers . . . . . . . . . . . . . . . . .

9
9

Preinstallation tasks to complete at the customer site . .
Verifying that all the required equipment is on site . .
Ensuring that the preinstallation tasks are complete .
Equipment specifications . . . . . . . . . . . . . . . .

.
.
.
.

9
9
10
10

About S8730 Server configurations . . . . . . . . . . . . . . . . . . . . . . . . .

About RAID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

About server port connections . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S8700-series port connections . . . . . . . . . . . . . . . . . . . . . . . . . .

13
14

About modem connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Modem options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19
20

About media gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

About Processor Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

About software duplication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

About SSH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 2: SNMP configuration . . . . . . . . . . . . . . . . . . . . . .

Configuring the SNMP modules in the UPS . . . . . . .
Default UPS IP addresses for S8700-series Servers
Prerequisites for configuring the SNMP module . .
Administering the SNMP modules . . . . . . . . . .
Setting selected traps (alarming) . . . . . . . . . .

.
.
.
.
.

.
.
.
.

.
.
.
.
.

.
.
.
.

.
.
.
.
.

.
.
.
.

.
.
.
.
.

.
.
.
.

.
.
.
.
.

.
.
.
.

.
.
.
.
.

.
.
.
.

.
.
.
.
.

.
.
.
.

.
.
.
.
.

23
24
25
26
26

Configuring the SNMP subagent in the Avaya Ethernet switch (if used)
Default IP addresses for the Ethernet switch . . . . . . . . . . . . .
Preparing to configure the Ethernet switch . . . . . . . . . . . . . .
Configuring the Ethernet switch . . . . . . . . . . . . . . . . . . . .

.
.
.
.

27
27
28
29

Chapter 3: Communication Manager installation . . . . . . . . . . . . .

Clearing the ARP cache on the laptop . . . . . . . . . . . . . . . . . . . . . . . .

Applying power to the server

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Accessing the server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuring Telnet for Windows 2000 and Windows XP . . . . . . . . . . . . . .

Installing Avaya Communication Manager . . . . . . . . . . . . . . . . . . . . .

Installing and Configuring the Avaya S8700-Series Server

.
.
.
.
.

.
.
.
.

January 2008

Contents

Chapter 4: Server configuration . . . . . . . . . . . . . . . . . . . . . .

Opening the Maintenance Web Interface. . . . . . . . . . . . . . . . . . . . . . .

Copying files to the server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Creating a super-user login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Methods of Configuring a server . . . . . . . . . . . . .
Configuring the server manually . . . . . . . . . . .
Setting the date, time, and time zone. . . . . . .
Maintenance Web Pages configuration screens.
Ethernet interface assignments. . . . . . . . . .
Performing the manual configuration . . . . . . . .
Avaya Installation Wizard . . . . . . . . . . . . . . .
About the Avaya Installation Wizard . . . . . . .
Running the Avaya Installation Wizard. . . . . .

.
.
.
.
.
.
.
.
.

37
37
37
38
40
40
41
41
42

Verifying the server connection to the customer LAN (if provided) . . . . . . . .

Configuring the modem

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuring memory for an S8720 Server . . . . . . . . . . . . . . . . . . . . . .

Ensuring ESS and LSP compatibility. . . . . . . . . . . . . . . . . . . . . . . . .

Enabling firewall settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Enabling network time servers . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuring the NIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Release the server

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Configuring a second server . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Interchanging servers . . . . . . . . . . . . . . . . . . .
Accessing the standby server . . . . . . . . . . . .
Interchanging servers . . . . . . . . . . . . . . . . .
Performing an integrity check on the active server .

.
.
.
.

48
48
49
49

. . . . . . . . . . . . . . . . . . .

Inputting initial system translations . . . . . . . . . . . . . . . . . . . . . . . . .

Adding media gateways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Enabling the IPSI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Adding the IPSI to the system . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Enabling IPSI duplication (duplicated control network only) . . . . . . . . . . .

Setting the alarm activation level . . . . . . . . . . . . . . . . . . . . . . . . . .

Saving translations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 6: IP interface configuration . . . . . . . . . . . . . . . . . . .

Connecting to the IPSIs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 5: IP interface translations

Installing and Configuring the Avaya S8700-Series Server

.
.
.
.
.
.
.
.
.

.
.
.
.

.
.
.
.
.
.
.
.
.

.
.
.
.

.
.
.
.
.
.
.
.
.

.
.
.
.

.
.
.
.
.
.
.
.
.

.
.
.
.

.
.
.
.
.
.
.
.
.

.
.
.
.

.
.
.
.
.
.
.
.
.

.
.
.
.

.
.
.
.
.
.
.
.
.

.
.
.
.

.
.
.
.
.
.
.
.
.

.
.
.
.

.
.
.
.
.
.
.
.
.

.
.
.
.

.
.
.
.
.
.
.
.
.

.
.
.
.

.
.
.
.
.
.
.
.
.

.
.
.
.

.
.
.
.
.
.
.
.
.

.
.
.
.

.
.
.
.
.
.
.
.
.

.
.
.
.

January 2008

Contents

IPSI address configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming the IPSI for static addressing
. . . . . . . . . . . . . . . . .

57
58

Setting the VLAN and diffserv parameters . . . . . . . . . . . . . . . . . . . . .
Programming the IPSI for DHCP addressing . . . . . . . . . . . . . . . . . .

61
62

Verifying connectivity to the server . . . . . . . . . . . . . . . . . . . . . . . . .

Verifying that the IPSIs are translated . . . . . . . . . . . . . . . . . . . . . . . .

Upgrading the IPSI firmware version (if necessary) . . . . . . . . . . . . . . . .

Enabling control of the IPSIs . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Verifying the license status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 7: Postinstallation administration . . . . . . . . . . . . . . . .

Verifying translations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Setting rules for daylight savings time . . . . . . . . . . . . . . . . . . . . . . .

Setting locations (if necessary) . . . . . . . . . . . . . . . . . . . . . . . . . . .

Verifying the date and the time (main server only) . . . . . . . . . . . . . . . . .

Clearing and resolving alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Enabling and disabling the Ethernet switch ports . . . . . . . . . . . . . . . . .

Enabling alarms to INADS by way of a modem . . . . . . . . . . . . . . . . . . .

Enabling alarms to INADS by way of the SNMP module . . . . . . . . . . . . . .

Backing up files to the compact flash media . . . . . . . . . . . . . . . . . . . .

Before leaving the site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Chapter 8: Installation verification . . . . . . . . . . . . . . . . . . . . .

Testing the IPSI circuit pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Testing the license file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

S8730 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

S8710 and S8720 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Additional server LED information . . . . . . . . . . . . . . . . . . . . . . . . . .

Avaya C360 Ethernet switch LEDs . . . . . . . . . . . . . . . . . . . . . . . . . .

UPS LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TN2312BP IPSI LEDs

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Appendix A: Server access . . . . . . . . . . . . . . . . . . . . . . . . .

Accessing the command line interface of the server with SSH . . . . . . . . . .

Connecting to the server directly . . . . . . . . . . . . . . . . . . . . . . . . . .

Connecting to the server remotely over the network . . . . . . . . . . . . . . . .

Connecting to the server remotely over a modem . . . . . . . . . . . . . . . . .

Installing and Configuring the Avaya S8700-Series Server

January 2008

Contents

Finding the IP address of the active server . . . . . . . . . . . . . . . . . . .

Accessing the Maintenance Web Interface . . . . . . . . . . . . . . . . . . . . .

Using the SAT command line prompt . . . . . . . . . . . . . . . . . . . . . . . .

Logins for Avaya technicians and BusinessPartners

. . . . . . . . . . . . . . .

Configuring the network for Windows 2000 and XP . . . . . . . . . . . . . . . .

Setting the browser options for Internet Explorer 6.0 . . . . . . . . . . . . . . .

Appendix B: Installation troubleshooting . . . . . . . . . . . . . . . . .

Troubleshooting the installation of the server hardware . . . . . . . . . . . . . .

Troubleshooting the configuration of the server hardware . . . . . . . . . . . .

Troubleshooting the installation of the license file and
the Avaya authentication file . . . . . . . . . . . . . . . . . . . . . . . . . . . .

100

Index

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installing and Configuring the Avaya S8700-Series Server

101

January 2008

Chapter 1: Introduction
Use these procedures to install Avaya Communication Manager and configure a new Avaya
S8700-series Server and the associated components in a fiber-connected (fiber-PNC) or an
IP-connected (IP-PNC) port network configuration.
To configure the server, use the Avaya Installation Wizard. To configure gateways and other
hardware components, use the following two administration interfaces:
●
●

The Maintenance Web Interface
The command line interface, either directly or through Secure Shell (SSH), Telnet, or a
terminal emulation program such as Avaya Native Configuration Manager.

This installation document includes the following information:
●

Pre-installation requirements on page 9

●

Configuring the SNMP modules in the UPS on page 23

●

Server configuration on page 35

●

IP interface translations on page 51

●

IP interface configuration on page 57

●

Postinstallation administration on page 67

●

Installation verification on page 75

●

Server access on page 87

●

Installation troubleshooting on page 97

Audience
This documentation is for the following people who install and configure the server components:
●

Trained field installation and maintenance personnel

●

Technical support personnel

●

Authorized business partners

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 1: Introduction

How to use Avaya installation documents
Use this document as a guide to install and configure Avaya servers. For information about a
particular task, use the index or the table of contents to locate the page on which the information
is described. You also need information from other Avaya documents. This section lists those
documents and tells you when to use them.
To complete this installation:
●

In this document, see:
- Pre-installation requirements on page 9 first. This section describes the tasks that your
must complete at the site before you start the installation.
- Equipment specifications on page 10 for the technical specifications for the hardware.

●

For how to install and connect the hardware, see Quick Start for Hardware Installation:
Avaya S8700-Series Server (555-245-701).
Return to this document and see the remaining sections in the following sequence to
install the components of the server. If you are not to install certain components, skip the
procedures for those components.
- Configuring the SNMP modules in the UPS on page 23
- Server configuration on page 35
- IP interface translations on page 51

●

See the appropriate sections in the following documents to install the port networks and
the media gateways:
-

Installing the Avaya G650 Media Gateway (03-300144)
Installation and Configuration for the Avaya G150 Media Gateway (03-300395)
Quick Start for Hardware Installation: Avaya G250 Media Gateway (03-300433)
Quick Start for Hardware Installation: Avaya G350 Media Gateway (03-300148)
Quick Start for Hardware Installation: Avaya G450 Media Gateway (03-602053)
Installing and Upgrading the Avaya G250 Media Gateway (03-300434)
Installing and Upgrading the Avaya G350 Media Gateway (03-300394)
Installing and Upgrading the Avaya G450 Media Gateway (03-602054)
Quick Start for Hardware Installation: Avaya S8300 Server and Avaya G700 Media
Gateway (555-233-150)
- Installation and Upgrade for the Avaya G700 Media Gateway and Avaya S8300 Server
(555-234-100)
- Avaya IA 770 INTUITY AUDIX Messaging Application Administering the S8300 and
S8400 Servers to work with IA 770
●

Return to this document and see:
- IP interface configuration on page 57 to program the IP interface.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Pre-installation requirements

- Postinstallation administration on page 67
- Installation verification on page 75
- Server access on page 87
- Installation troubleshooting on page 97 if problems occur during the installation.

Pre-installation requirements
This section describes the tasks that you must complete before you start the installation. You
complete certain tasks before you go on site and other tasks at the site.

PNC license settings for S8700-series Servers
For Communication Manager Release 4.0 and later releases, the two major types of port
network connectivity, IP-PNC and fiber-PNC (also called multiconnect), are both automatically
enabled in all licenses for S8700-series Server. As a result, unlike the license settings in
previous releases, platform 8 for IP-PNC and the Internet Protocol (IP) PNC feature attribute
are no longer needed and are not available as license options. For Release 4.0 and later
releases, you always select platform 6, multiconnect, in a license for an S8700-series Server.

Preinstallation tasks to complete at the customer site
Before you start the installation, you must:
●

Verify that all the required equipment is on site

●

Ensure that the preinstallation team completed the preinstallation tasks

●

Install the DAL2 card, if used

Verifying that all the required equipment is on site
Compare the list of items that were ordered to the contents of the boxes to verify that you have
all the equipment. Your project manager can give you an inventory list. Do not rely on the
packing slips inside the boxes for the correct information.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 1: Introduction

Ensuring that the preinstallation tasks are complete
The preinstallation team completes the following tasks. If these tasks are not complete, do not
continue with the installation.
●

●
●

●

●
●

Verify that the required number of open, customer-supplied, EIA-310D (or equivalent)
standard 19-in. (48-cm) 4-post equipment rack(s) is(are) properly installed and solidly
secured. Ensure that the screws that come with the racks are present. If you use a rack
cabinet, ensure that the cabinet has adequate ventilation.
Verify that the rail kit to support the server is available to install.
Verify that the rail kit that is required to support the UPS is installed on the rack or available
to install. For how to install the rails, see the documentation that comes with the rail kit.
Verify that the equipment racks are grounded per local code. See Job Aid: Approved
Grounds (555-245-772).
Verify that the customer-provided AC power to the rack is from a nonswitched outlet.
Verify that cables for theTN2312BP (IPSI) circuit packs are labeled and run from the
control hardware rack to the port networks or that appropriate connectivity is provided.

Equipment specifications
The components of the S8700-series Server control network consist of two servers, one or two
Ethernet switches, and two UPSs. The physical specifications for the control network
components are shown in Table 1.
Table 1: Control network components specifications
Dimensions
English

Dimensions
Metric

(height x width x depth
in inches)

(height x width x depth
in centimeters)

Server
S8710, S8720, or
S8730

3.4 x 17.5 x 26

Ethernet switch:
C363T
C364T
UPS:
700 VA
1500 VA

Component

Height
(u)

Weight
(lb/kg)

8.6 x 45 x 66

60/27
(loaded)

1.75 x 17 x 14.4
1.75 x 17 x 14.4

4 x 43 x 37
4 x 43 x 37

1
1

11/5
11/5

3.5 x 17 x 19
3.5 x 17 x 24

9 x 43 x 48
9 x 43 x 61

2
2

34/15
50/23

Installing and Configuring the Avaya S8700-Series Server

January 2008

Preinstallation tasks to complete at the customer site

Table 2 shows specifications for the S8710, S8720 and S8730 Servers.
.

Table 2: S8710, S8720 and S8730 Server features and specifications
Feature

Description

Microprocessor

S8710: 1 Intel Xeon
S8720: 1 AMD Opteron
S8730 1 Dual Core rev "F" AMD

Memory

S8710: 512 MB
S8720: 1 GB
S8730: 4 GB

Drives (SCSI)

Hard disk drive: 72 GB, 10,000 RPM
CD-ROM/DVD-ROM: 24x maximum
Diskette drive: 1.44 MB (3.5 in. [9 cm])

DAL2 hardware
duplication cards

Used for the hardware duplication configuration only. Not used
for the software duplication configuration.

Physical dimensions

S8710/S8720:
Height: 3.4 inches [8.6 cm], 2 U)
Depth: 26 inches (66 cm)
Width: 17.5 inches (45 cm)
Maximum weight: 60 lb (27 kg)
S8730:
Height: 3.38 inches [8.59 cm], 2 U)
Depth: 26.01 inches (66.07 cm)
Width: 17.54 inches (44.54 cm)
Maximum weight: 60 lb (27.22 kg)

Integrated functions

S8710/8720: 2 10/100/1000BaseT Ethernet connectors
S8730: 2 100/1000Gb Ethernet ports
Serial connector
iLO connector (unused)
Keyboard connector
Mouse connector
USB connectors:
S8710: 2
S8720: 3
S8730: 4
Video connector
VHDCI SCSI connector

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 1: Introduction

Environmental specifications for the S8710, S8720 and S8730 are shown in Table 3.
.

Table 3: S8710/S8720/S8730 Server environmental specifications
Parameter

Description

Air Temperature

Ambient operating: 50°F to 95°F (10°C to 35°C)
Maximum wet bulb: 82.4°F (28°C)
NOTE: All temperature ratings shown are for sea level. An altitude
derating of 1.8°F per 1000 ft to 10,000 ft (1°C per 300 meters) is
applicable. No direct sunlight is allowed.

Humidity

Operating: 10% to 90%
Nonoperating: 5% to 85% (S8730: 5% to 95%)
NOTE: The storage maximum humidity of 95% is based on a
maximum temperature of 113°F (45°C). The altitude maximum for
storage corresponds to a pressure minimum of 70 kPa.

Electrical input

Rated input voltage:
S8710/8720:100 VAC to 240 VAC
S8730:100 to 132 VAC, 200 to 240 VAC
Rated input frequency: 50 Hz to 60 Hz
Rated input current:
S8710/8720: 6 A (110 V) to 3 A (220 V)
S8730:10 A at 100 VAC, 4.9 A at 200 VAC
Rated input power:
S8710/8720: 600 W
S8730:
980 W at 100V AC input
960 W at 200V AC input
BTUs per hour: 2050

Power supply output

Rated steady-state power:
S8710/8720:400 W
S8730:
800 W at 100V AC input
850 W at 120V AC input
1000 W at 200V to 240V AC input
Maximum peak power:
S8710/8720: 400 W

Installing and Configuring the Avaya S8700-Series Server

January 2008

About S8730 Server configurations

About S8730 Server configurations
The S8730 Server comes with the option of two hard disk drives. In configurations with two hard
drives, the RAID level 1 feature is enabled, so that disk mirroring automatically creates a
complete set of data on both disks.
For different configurations of the S8730 Server:
●

If the server has only one hard drive, the drive should be in bay 1 (the leftmost bay)

●

If the server has two hard drives, the drives should be in bay 1 and bay 2.

After installation, do not attempt to move a drive from one bay to the other. If movement of
drives is necessary, the server must be reinstalled.

About RAID
One or more hard drives may be added to an S8730 Server in order to take advantage of the
RAID level 1 feature, which provides disk mirroring. In this configuration, a customer’s data is
mirrored on two disks, thus increasing the availability of the system. Each of the disks is
independent of each other and contains a complete copy of the data. No administration is
necessary to activate the RAID feature. Once an additional hard drive is installed,
Communication Manager recognizes the additional hard drive and automatically activates
RAID.

Note:

Note:
The RAID level 1 feature is only available on S8730 Servers.

About server port connections
The following section explains how to connect the Ethernet ports on the back of the server.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 1: Introduction

S8700-series port connections
The network cable connections depend on the type of server, type of memory duplication, and
the type of control network. All cables are CAT5 or better patch cables except for the fiber cable
that interconnects the DAL2 cards for hardware duplication.
●

●

For a guide to connect the cables to the servers for hardware duplication on the S8730
Server, see Figure 1: Duplication and control network cabling for hardware duplication
(S8730) on page 15.
For a guide to connect the cables to the servers for hardware duplication on the S8720 or
S8710 Server, see ,Figure 2: Duplication and control network cabling for hardware
duplication (S8720/S8710) on page 16.
For a guide to connect the cables to the servers for software duplication on the S8730
Server, see Figure 3: Duplication and control network cabling for software duplication
(S8730) on page 17.
For a guide to connect the cables to the servers for software duplication on the S8720 or
S8710 Server, see ,Figure 4: Duplication and control network cabling for software
duplication (S8720/S8710) on page 18.

Installing and Configuring the Avaya S8700-Series Server

January 2008

About server port connections

Figure 1: Duplication and control network cabling for hardware duplication (S8730)
4

DAL1
DUP
MEMORY

LINC
ACTIVE

LINC
SYNC

TRANS
MODE

RECEIVE
MODE

4
2

1
PCIe 2

PCIe 1

ILO 2

UID

DAL1
DUP
MEMORY

LINC
ACTIVE

LINC
SYNC

TRANS
MODE

RECEIVE
MODE

4
2

3
1
PCIe 2

PCIe 1

ILO 2

UID

2
3
hw8730h2 LAO 082807

Figure notes:
1.
2.
3.
4.
5.

Note:

Eth0 — CNA (also LAN for nondedicated control network)
Eth2 — Server duplication link - duplication crossover cable
Eth3 — To an Ethernet switch and/or the corporate LAN for control network B (CNB)
Eth4 — To the customer LAN if the control networks are dedicated
Fiber duplication cable

Note:
These are typical Ethernet port assignments. The customer might specify
different assignments for Eth0, Eth2, Eth3, and Eth4.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 1: Introduction

Figure 2: Duplication and control network cabling for hardware duplication (S8720/S8710)
4

DAL1
DUP
MEMORY

LINC
ACTIVE

LINC
SYNC

TRANS
MODE

RECEIVE
MODE

100 MGz

100 MGz
iLO

133 MGz

VDCI

UID

2
3

LINC
ACTIVE

DAL1
DUP
MEMORY

LINC
SYNC

TRANS
MODE

RECEIVE
MODE

100 MGz

2
100 MGz
iLO

133 MGz

VDCI

UID

3
1
h3df87h2 LAO 122206

Figure notes:
1.
2.
3.
4.
5.

Note:

Eth0 — To an Ethernet switch and/or the corporate LAN for control network A (CNA)
Eth2 — Server Duplication Link
Eth3 — To an Ethernet switch and/or the corporate LAN for control network B (CNB)
Eth4 — To the customer LAN if the control networks are dedicated
Fiber duplication cable

Note:
These are typical Ethernet port assignments. The customer might specify
different assignments for Eth0, Eth2, Eth3, and Eth4.

Installing and Configuring the Avaya S8700-Series Server

January 2008

About server port connections

Figure 3: Duplication and control network cabling for software duplication (S8730)
4

4
2

3
1
PCIe 2

PCIe 1

ILO 2

UID

1
5

4
2

3
1
PCIe 2

PCIe 1

ILO 2

UID

2
3

hw8730s2 LAO 081607

Figure notes:
1.
2.
3.
4.

Note:

Eth0 — Server Duplication Link - duplication crossover cable
Eth2 — To an Ethernet switch and/or the corporate LAN for control network A (CNA)
Eth3 — To an Ethernet switch and/or the corporate LAN for control network B (CNB)
Eth4 — To the corporate LAN if the control networks are dedicated.

Note:
These are typical Ethernet port assignments. The customer might specify
different assignments for Eth2, Eth3, and Eth4.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 1: Introduction

Figure 4: Duplication and control network cabling for software duplication (S8720/S8710)
4

3
100 MGz

100 MGz
iLO

133 MGz

VDCI

UID

1
3

3
100 MGz

2
100 MGz
iLO

133 MGz

VDCI

UID

2
3

h3df87s2 LAO 122206

Figure notes:
1.
2.
3.
4.

Note:

Eth0 — Server Duplication Link
Eth2 — To an Ethernet switch and/or the corporate LAN for control network A (CNA)
Eth3 — To an Ethernet switch and/or the corporate LAN for control network B (CNB)
Eth4 — To the corporate LAN if the control networks are dedicated.

Note:
These are typical Ethernet port assignments. The customer might specify
different assignments for Eth2, Eth3, and Eth4.

Installing and Configuring the Avaya S8700-Series Server

January 2008

About modem connections

About modem connections
Note:

Note:
You cannot connect USB modems to rotary lines. A touch tone line is required.

On S8700-series Servers, connect a USB modem to the USB port on each server.
!
CAUTION:

CAUTION:
Once you connect the modems to the servers, do not unplug the modem USB
cable on the active server. If you must replace the modem, replace the modem
when the server is in standby mode.

Connecting to collocated servers
!
Important:

Important:
Both servers share one telephone line.

To connect modems to collocated servers:
1. Install two RJ11 jack outlets wired to a single (1-Measured Business) telephone line.
2. Use the modular telephone cord that is supplied with the modem to connect one RJ11 jack
to each modem.
3. Use the USB cable that is supplied with the modem to connect one modem to server 1.
4. Use the USB cable to connect the other modem to server 2.

Connecting to separated servers
!
Important:

Important:
Each server has a dedicated telephone line.

To connect to separated servers:
1. For a server in each location, install one RJ11 jack outlet that is wired to a single
1-Measured Business telephone line.
2. Use the modular telephone cord that is supplied with the modem to connect one RJ11 jack
to each server.
3. Connect each modem, using the USB cable, to the server at each location.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 1: Introduction

Modem options
You set the modem options when you configure the server. You do not set options on the
modems themselves.

About media gateways
In a new installation, the S8700-series Servers work with only the Avaya G650 Media Gateway.
In a migration, the S8700-series Servers work with Avaya MCC1 and SCC1 Media Gateways in
a fiber-PNC configuration and G600 or CMC1 Media Gateways in an IP-PNC configuration.
The servers also work with Avaya G150, G250, G350, G450 and G700 Media Gateways. These
gateways register with the server either through the Processor Ethernet interface or through a
TN799DP C-LAN circuit pack.
Media gateways usually are installed in the same equipment room as the server rack hardware
or control network. However, you can install the media gateways in another location, including
another state or country.

About Processor Ethernet
Like a C-LAN circuit pack, Processor Ethernet provides connectivity to IP endpoints, gateways,
and adjuncts. The PE interface is a logical connection in the Communication Manager software
that uses a port on the NIC in the server. No additional hardware is needed to implement PE.
Starting with Release 3.1 of Communication Manager, the PE interface is enabled on the
S8700-Series Server to allow enhanced flexibility to connect to gateways, endpoints, and
adjuncts.
The PE interface is always enabled on an S8700-series Server pair for registration by an ESS
or an LSP. However, the PE interface is not supported on duplex servers for registration by an
H.248 gateway, H.323 endpoints, or adjuncts.

Installing and Configuring the Avaya S8700-Series Server

January 2008

About software duplication

About software duplication
Software duplication eliminates the need for the DAL2 duplication cards in duplicated S8720
and S8730 Servers. Software duplication is supported only on the S8720 and S8730 and is the
default configuration. For software duplication, all duplication messages are sent over the
server duplication TCP/IP link.
An S8720 or S8730 communications system configured with software duplication has lower call
performance than the same system configured with hardware duplication. Encrypting
duplication messages further degrades performance. For software duplication, Avaya
recommends that you use a dedicated duplication link with a bandwidth of at least 1 Gigabit per
second.
The S8720 and S8730 Server is shipped without the optional DAL2 hardware duplication card.
If purchased, the DAL2 hardware duplication cards and the dual fiber cable that links the DAL2
cards are installed in the servers at the customer site.
The duplication type, that is, hardware or software, is administered as a Configure Server step
on the Server Duplication Web page in the Maintenance Web Interface.

About SSH
Secure Shell (SSH) is both a computer program and an associated network protocol that you
use to log in to and run commands on a networked computer. SSH provides secure encrypted
communications between two untrusted hosts over an insecure network. Avaya strongly
recommends that you use SSH instead of Telnet for most interactive connections to the Avaya
servers and other devices on a customer network.
To use SSH, a third-party SSH client must be installed on your computer. PuTTY is one such
client. You can download PuTTY from http://www.putty.nl/download.html.
You can use SSH to access the following devices:
●

The S8300, S8400, S8500, and S8700-series Servers on Release 3.1 or later of
Communication Manager
Note:
With Release 4.0 or later of Communication Manager, Telnet is disabled, so you
must use SSH to access the servers after Communication Manager software
Release 4.0 or later is installed.

Note:

●

A Maintenance Processor Complex (MPC), which is used with the S8400 Server

●

A TN2312BP IPSI that is running firmware version 20 or higher

●

A TN8412AP SIPI

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 1: Introduction

●

A TN2602 IP Media Resource that is running firmware version 212 or higher

●

An Expanded Meet-Me Conferencing (EMMC) server

●

A SIP Enablement Services (SES) server

●

G250, G350, and G450 media gateways

●

C360 Ethernet switches

!
Important:

Important:
You cannot use SSH with the G700. From within the Linux command line of a
server, you can use SSH to access the G250, 350, and G450, but you must use
Telnet to access the G700.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Configuring the SNMP modules in the UPS

Chapter 2: SNMP configuration
After you install and connect the control network equipment, you must configure the SNMP
modules in each Avaya-supplied UPS to send alarms or traps to the servers. This process
requires that you also configure the SNMP subagent in the Avaya-supplied Ethernet switch.

!
Important:

Important:
Use the procedures in this section to configure Avaya-supplied equipment only.

Configuring the SNMP modules in the UPS
!
Important:

Important:
These procedures apply only to a new, Avaya-supplied uninterruptible power
supply (UPS) with a Simple Network Management Protocol (SNMP) module. Do
not use these procedures to set traps on a UPS that Avaya does not supply.

You must configure the SNMP module in the UPS to report alarms to the server when hardware
problems occur. The module reports an alarm if commercial power is lost or battery resources
are depleted.
For the SNMP module to properly report alarms, you must configure a unique IP address for the
UPS on both the SNMP module and the server. This IP address can be a customer-provided
address or the Avaya-provided default address. At a minimum, you must configure the following
items:
●

The IP address

●

The subnet mask

●

The gateway IP address

●

The trap receiver IP address

●

The community string (get, set, trap)

A third party manufactures the SNMP module. The brand, the model, or the firmware load of the
module that Avaya supplies can change without notice. For this reason, this document does not
provide specific instructions on how to connect to and configure the SNMP module. For more
information, see the documentation that comes with the SNMP module. For the default
password and the configuration commands, see the local configuration section of that user
guide.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 2: SNMP configuration

Default UPS IP addresses for S8700-series Servers
For how to administer the SNMP module in the UPS, see . Perform the same steps for each
UPS. Table 4: Default UPS IP addresses for a dedicated control network shows the default
values for UPS1 and UPS2 for a dedicated control network. For non-dedicated control
networks, the customer provides IP addresses.

!
Important:

Important:
Do not use the IP address of the active server.

Table 4: Default UPS IP addresses for a dedicated control network
Parameter

UPS

Single control
network (CNA)

Duplicated control
network (CNB)

IP address
Subnet mask

UPS 1

198.152.254.239
255.255.255.0

198.152.255.239
255.255.255.0

Gateway address

UPS 1

198.152.254.201

198.152.255.201

IP address for the
trap receiver (server 1)

UPS 1

198.152.254.201

198.152.255.201

IP address
Subnet mask

UPS 2

198.152.254.238
255.255.255.0

198.152.255.238
255.255.255.0

Gateway address

UPS 2

198.152.254.201

198.152.255.201

IP address for the
trap receiver (server 2)

UPS 2

198.152.254.202

198.152.255.202

!
Important:

Important:
Each UPS must report SNMP traps to the server that the UPS powers.

If the UPS detects that commercial power is lost or battery resources are depleted, the UPS
sends a trap that allows the server to lower its state of health and to cause an interchange. If the
UPS sends the trap to the wrong server trap receiver address, that server interchanges to the
server that is plugged into the failing UPS. Thus, server 1 must be plugged into UPS1, and
UPS1 must be configured to report SNMP traps to the actual IP address, and not the active
server address, of server 1. The same requirements apply to server 2 and UPS2.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Configuring the SNMP modules in the UPS

Prerequisites for configuring the SNMP module
Before you configure the SNMP module, you must complete the following prerequisites:
●

●
●

Your Services laptop computer is plugged into the correct administration port on the SNMP
module on the UPS.
The UPS is plugged into a nonswitched electrical outlet.
The communication protocol on your computer has the following port settings so that you
can use your terminal emulation program:
- 9600 baud
- No parity
- 8 data bits
- 1 stop bit
- No flow control
Note:
Avaya Terminal Emulation and HyperTerminal are supported terminal emulation
applications.

Note:

●

If a Network Management System (NMS) is used to monitor the UPS, you must
coordinated the assignment of community names with the network administrator. If an
NMS is not used, you can set the community names to any unique string values.
!

SECURITY ALERT:

SECURITY ALERT:
The Get and Set community name strings are initially configured with the default
values of Public and Private, respectively. These community name strings
function as passwords for their respective SNMP operation. Avaya recommends
that you change these community name strings to something other than the
default values. If you leave the defaults in place, a serious security issue can
result.

For information about which traps to set, see Setting selected traps (alarming) on page 26.
●

If the control network is nondedicated, ensure that the 162/udp port for input to server is
enabled and the default is disabled. If you do not enable the 162/udp port and disable the
default, the server cannot receive the traps from either UPS. See Enabling firewall
settings on page 46.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 2: SNMP configuration

Administering the SNMP modules
Note:
Use the default IP addresses.

Note:

1. Connect the RS-232 serial port of your Services laptop computer to the DB-9 connector on
the back of the SNMP module for UPS1 using the DB-9 to DB-9 serial cable that is
supplied with the SNMP module.
2. Open a VT-100 terminal emulation session on your computer.
3. Set the IP address for the UPS.
4. Set the subnet mask for the UPS.
5. Set the gateway address for the UPS.
6. Set the IP address of the trap receiver for the UPS.
7. Set the SNMP community name string for Get, Set, and Trap. For information on which
traps to set, see Setting selected traps (alarming) on page 26.
8. When finished, disconnect your computer from the UPS.
9. Connect one end of a CAT5 straight-through cable to the RJ45 connector on the UPS1
SNMP module and the other end of the cable to the next available port on the Ethernet
switch for Control Network A (CNA).
For a connectivity guide, see the Quick Start for Hardware Installation: Avaya S8700
Series Server (555-245-703).
10. Repeat Steps 1 through 8 for the SNMP module in UPS2.
11. For UPS2, connect one end of a CAT5 straight-through cable to the RJ45 connector on the
UPS2 SNMP module. Connect the other end of the cable to the next available port on the
Ethernet switch for Control Network B (CNB).
For a connectivity guide, see the Quick Start for Hardware Installation: Avaya S8700
Series Server (555-245-703).
After you configure the SNMP module in the UPS, you must configure the SNMP subagent on
the Avaya Ethernet switch.

Setting selected traps (alarming)
The default is to set all traps, which can result in large log entries. To avoid this problem, Avaya
recommends that you set only the following traps:
●

UPS on Battery—Indicates an AC power failure. Based on the level of battery reserve, a
shutdown is pending.

●

UPS in Bypass—The UPS failed or is overloaded.

●

Replace battery—The battery failed the 28-day battery test and must be replaced.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Configuring the SNMP subagent in the Avaya Ethernet switch (if used)

For the menus and commands to set these traps, see the user guide that comes with the SNMP
module.

Configuring the SNMP subagent in the Avaya Ethernet
switch (if used)
!
Important:

You must administer the Simple Network Management Protocol (SNMP) subagent in the Avaya
Ethernet switch to report alarms to the server when problems occur.
For the SNMP module to properly report alarms, you must configure a unique IP address for the
UPS on both the SNMP module and the server. This IP address can be a customer-provided
address or the Avaya-provided default address. At a minimum, you must configure the following
items:
●

The IP address

●

The subnet mask

●

The gateway IP address

●

The trap receiver IP address

●

The community string (get, set, trap)

The brand, the model, or the firmware load of the Ethernet switch that Avaya supplies can
change without notice. For this reason, this document does not provide specific instructions on
how to connect to and configure the SNMP subagent. For more information, see the
documentation that comes with the Ethernet switch. Also see the Basic Configuration section of
the Quick Start Guide and the documentation CD-ROM that comes with the Ethernet switch for
the default user ID, password, and configuration commands.

Note:

Note:
For the Ethernet switch to report alarms properly, you must also configure the IP
addresses for the Ethernet switches in the servers.

Default IP addresses for the Ethernet switch
For how to administer the SNMP subagent in the Ethernet switches see Configuring the
Ethernet switch on page 29. If the control network is duplicated, perform the same steps for
both Ethernet switches.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 2: SNMP configuration

Table 5: Default values for a dedicated control network shows the default values for Ethernet
switch 1 and Ethernet switch 2 for a dedicated control network.
For non-dedicated control networks, the customer will provide IP addresses

!
Important:

Important:
Do not use the IP address of the active server.

Table 5: Default values for a dedicated control network
Parameter

Ethernet
switch

Single control
network (CNA)

Duplicated control
network (CNB)

IP address
Subnet mask

198.152.254.240
255.255.255.0

198.152.255.240
255.255.255.0

IP address for the
trap receiver (server 1)

198.152.254.201

198.152.255.201

IP address
Subnet mask

198.152.254.241
255.255.255.0

198.152.255.241
255.255.255.0

IP address for the
trap receiver (server 2)

198.152.254.202

198.152.255.202

Preparing to configure the Ethernet switch
Before you configure the Ethernet switch, you must complete the following prerequisites:
●

The Ethernet switch power cord is connected to the back of the switch and to the back of a
UPS.
- For a single control network, connect the Ethernet switch 1 for Control Network A
(CNA) into UPS 1.
- For a duplicated control network, connect the Ethernet switch 1 for CNA into UPS 1
and connect the Ethernet switch 2 for Control Network B (CNB) into UPS 2.

●

The communication protocol on your computer has the following port settings so that you
can use your terminal emulation program:
- 9600 baud
- No parity
- 8 data bits
- 1 stop bit
- No flow control

Installing and Configuring the Avaya S8700-Series Server

January 2008

Configuring the SNMP subagent in the Avaya Ethernet switch (if used)

Note:
Avaya Terminal Emulation and HyperTerminal are supported terminal emulation
applications.

Note:

●

If a Network Management System (NMS) is to monitor the Ethernet switch, you
coordinated the assignment of community names with the network administrator. If an
NMS is not used, you set the community names to unique string values.
!

SECURITY ALERT:

●

If the control network is not dedicated, ensure that the 162/udp port for input to server is
enabled and the default is disabled. If you do not enable the 162/udp port and disable the
default, the server cannot receive the traps from either UPS. See Enabling firewall
settings on page 46.

Configuring the Ethernet switch
Note:

Note:
Use the default addresses.
1. Connect the RS-232 serial port of your Services laptop computer to the port labeled
Console on the front of Ethernet switch 1 (CNA). Use the flat cable supplied with the Avaya
Ethernet switch.
2. Open a VT-100 terminal emulation session on your computer.
3. Set the IP address for the Ethernet switch.
4. Set the subnet mask for the Ethernet switch.
5. Set the gateway IP address for the Ethernet switch.
6. Set the IP address of the trap receiver for the Ethernet switch.
7. Set the SNMP community name string for Get, Set, and Trap. For information about setting
these values, see the section on SNMP commands on the documentation CD-ROM that
comes with the Avaya Ethernet switch.
8. Use the command set spantree enabled to verify that spanning tree is enabled. Note
that enabled is the default setting.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 2: SNMP configuration

9. Use the command set spantree version rapid-spanning-tree to set the
spanning tree version to rapid-spanning-tree. Do not use the default.

Note:

Note:
This command is available on Avaya Ethernet switches with firmware version 4.0
or later. To use this command, you must update the firmware to this version, if
necessary.
For more information on the spanning tree CLI commands, see Installation and
Configuration Guide, Avaya C360 and Reference Guide, Avaya C360. These documents
are available at the Avaya Support Web site http://www.avaya tha.com/support.
10. If the port networks are IP-PNC, ensure that all appropriate ports on the Ethernet switch
are locked to 100 speed and full duplex.
11. When you finish, disconnect your computer from the Ethernet switch.
12. If two Ethernet switches are present for CNA, repeat Steps 1 through 10 for the second
switch.
13. If the control network is duplicated, repeat Steps 1 through 11 for each Ethernet switch that
remains.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Clearing the ARP cache on the laptop

Chapter 3: Communication Manager
installation
A new server comes with a blank hard disk drive. Use the bootable software distribution
CD-ROM to install the Linux operating system and Avaya Communication Manager. On a
duplicated system, install the software from the CD onto the hard drive of each server.
This chapter covers the following tasks:
●

Clearing the ARP cache on the laptop on page 31

●

Applying power to the server on page 32

●

Accessing the server on page 32

●

Configuring Telnet for Windows 2000 and Windows XP on page 32

●

Installing Avaya Communication Manager on page 33

Clearing the ARP cache on the laptop
Depending on the operating system of your Services laptop computer, you might need to clear
the Address Resolution Protocol (ARP) cache before you enter a new IP address. If you enter
an IP address and your computer cannot connect, perform the following procedure to clear the
cache.
1. On your computer, click Start > Run to open the Run dialog box.
2. Type command and press Enter to open an MS-DOS command line window.
3. Type arp -d 192.11.13.6 and press Enter to clear the ARP cache in the laptop.
If the ARP cache does not contain the specified IP address, the message The specified
entry was not found appears. You can ignore this message.
4. Type exit and press Enter to close the command line window.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 3: Communication Manager installation

Applying power to the server
Note:

Note:
In this procedure, the software CD-ROM must be placed into the CD-ROM drive
on the server prior to or immediately after you turn on the power to the server.
1. Connect the AC power cord to server 1 and to UPS 1.
2. Press the Power button on the front of the server. Immediately place the Avaya
Communication Manager CD-ROM into the CD-ROM drive on the server.

Accessing the server
1. Use a cross-over cable to connect your laptop computer to the Services port on the back
of the server. The Services port is labeled "2" and is configured as Eth1.
2. Wait at least 3 minutes after you turn on the server before you start a Telnet session to
access the information on the CD-ROM.

Configuring Telnet for Windows 2000 and Windows XP
The Microsoft Telnet application might be set to send a carriage return (CR) and a line feed (LF)
whenever you press Enter. The Communication Manager installation program sees this as two
separate key presses. If you are running Windows 2000 or Windows XP, you must correct this
setting before you copy the Remaster Program to the hard disk drive.
1. Click Start > Run to open the Run dialog box.
2. Type telnet and press Enter to open a Microsoft Telnet session.
3. Type unset crlf and press Enter.
4. Type display and press Enter to verify that you see the message Line feed mode Causes return key to send CR.
5. Type q and press Enter to exit the telnet session.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Installing Avaya Communication Manager

Installing Avaya Communication Manager
Use a Telnet session to access the information on the CD-ROM.
1. On your Services laptop computer, click Start > Run to open the Run dialog box.
2. Type telnet 192.11.13.6 and press Enter to view the first screen.

Note:

Note:
To navigate on these screens, use the arrow keys to move to an option, and then
press the spacebar to select the option. Press Enter to submit the information on
the screen.
3. Select Install, ensure that is highlighted, and press Enter.
4. On the Select Release Version screen, ensure that the Build line and are
highlighted.
5. Press Enter to partition the hard disk drive and format the partitions.
Once the drive is properly configured, the program starts the installation process and
reports the progress.
These processes can take up to 20 minutes to complete.
6. You must remove the CD-ROM from the drive at this time. When the server is ready to
reboot, the drawer of the CD-ROM drive opens.
The reboot can take up to 3 minutes. The Telnet session drops automatically when the
reboot starts.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 3: Communication Manager installation

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 4: Server configuration
After you install the Communication Manager software, you must use the Avaya Installation
Wizard to configure the server.
This section covers the following tasks:
●

Copying files to the server on page 36

●

Creating a super-user login on page 36

●

Note:

Configuring the server manually on page 37

●

Running the Avaya Installation Wizard on page 42

●

Verifying the server connection to the customer LAN (if provided) on page 42

●

Configuring the modem on page 43

●

Configuring memory for an S8720 Server on page 44

●

Enabling firewall settings on page 46

●

Enabling network time servers on page 46

●

Release the server on page 48

●

Configuring a second server on page 48
Note:
Ensure that you have the completed Electronic Preinstallation Worksheet (EPW)
before you start this process.
Note:
Ensure that your networking and Web browser settings are correct. For more
information, see Configuring the network for Windows 2000 and XP on page 95.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 4: Server configuration

Opening the Maintenance Web Interface
You can use the Maintenance Web Interface to copy license files and authentication files,
service packs, and update files from the Services laptop to the server. For how to open the
Maintenance Web Interface, see Finding the IP address of the active server on page 93.

Copying files to the server
1. From the Maintenance Web Interface, under Miscellaneous, click Download Files.
2. Select File(s) to download from the machine I’m using to connect to the server.
3. Click Browse next to the top field to open the Choose File window on your computer. Find
the files that you need to copy to the server.
4. Click Download to copy the files to the server.
The files are automatically copied to the default file location /var/home/ftp/pub.

Creating a super-user login
Note:

Note:
A craft level login can create the super-user login in Release 4.0 or later.

Make sure you have a login name and password that the customer would like for the superuser
login. If you are a business partner, you can also repeat this procedure to add the dadmin login.
Use the Integrated Management Maintenance Web Pages to create a super-user login.

To create a login:
Note:

Note:
Make sure the customer can change this login, its password, or its permissions
later.
1. In the Integrated Management Maintenance Web Pages, under Security, select
Administrator Accounts.
2. Select Add Login.
3. Select Privileged Administrator and click Submit.
The Administrator Accounts -- Add Login: Privileged Administrator screen appears.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Methods of Configuring a server

4. In the Login name field: Type a login name for the account.
5. In the Primary group field: susers appears.
6. In the Additional groups (profile) field: prof18 appears (prof18 is the code for the
customer superuser).
7. In the Linux shell field: /bin/bash appears
8. In the Home directory field: /var/home/login name appears (login name is the name you
choose in step 4.
9. Skip the Lock this account and Date on which account is disabled-blank to ignore
fields.
10. In the Select type of authentication section: Choose Password.
Note:
Do not lock the account or set the password to be disabled.

Note:

11. In the Enter key or password field and the Re-enter key or password field: Enter the
password.
12. In the Force password/key change on next login section: Leave the default to no.
13. Click Submit.

Methods of Configuring a server
The server can be configured using one of the following methods:
1. Configuring the server manually on page 37 using Integrated Management Maintenance
Web Pages
2. The Avaya Installation Wizard with the Electronic Pre-installation Worksheet (EPW)
3. The Avaya Installation Wizard interactively

Configuring the server manually
Setting the date, time, and time zone
!
Important:

Important:
Be sure to set the date, time, and time zone before manually configuring the
server. Failure to do so may cause network problems.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 4: Server configuration

To set the date, time, and time zone:
1. From the Main Menu, under Server, click Server Date/Time.
2. In the Server Date/Time window, verify the date and time are correct. If the date and time
are incorrect:
a. Enter the date
b. Enter the time
c. Enter the time zone
d. Click Submit
!
WARNING:

WARNING:
If you set time zone, you must reboot the server.

e. Reboot the server:
1. Click Shutdown Server under the Server heading.
2. Select Delayed Shutdown and Restart server after shutdown.
3. Click Shutdown.
You will be logged off the server when it reboots. You can use ping to verify when the
server is accessible again.

Maintenance Web Pages configuration screens
The following table shows the web pages you may need to complete for manual server
configuration. For each server configuration (for example, main, LSP, or ESS), the table shows
whether that screen must be completed or not.
Table 6: S8700-Series Server configuration web pages

Page

S8700-series Main

S8700-series ESS

Set Identities

Configure Interfaces

Configure ESS

Configure Memory (S8720
only)

Configure Switches

Installing and Configuring the Avaya S8700-Series Server

January 2008

Methods of Configuring a server

Table 6: S8700-Series Server configuration web pages
Page

S8700-series Main

S8700-series ESS

Set DNS/DHCP

Set Static Routes

Configure Time Server

Set Modem Interface

The following describes each of the configuration pages:
●

●

Set Identities — Use this page to assign Avaya server host names and to assign server
functions to a physical Ethernet interface. The options are pre populated with defaults, but
should be changed as needed for the customer’s configuration. See Ethernet interface
assignments on page 40 for a guide to assigning functions to Ethernet interfaces.
Configure Interfaces — Use this page to enter the IP address, subnet mask, gateway,
and speed for the management LAN and control network.
Configure ESS/LSP — Use this page to configure the server as either a primary controller
for the system or as an Enterprise Survivable Server (ESS) or a Local Survivable
Processor (LSP).
Configure Memory — For the S8720 main or ESS server, S8710 ESS server, use this
page to configure the server as either standard or extra large. A server that is configured
as extra large provides higher capacities.
Configure Switches — Use this page to specify an IP address and optional SNMP
community strings for any Ethernet adjuncts that the Avaya server controls, that are
connected to the server over a private LAN.
Set DNS/DHCP — Use this page to enable the different devices (endpoints) in your Avaya
call-processing system to communicate over the corporate LAN. Most corporate networks
have one or more domain name service (DNS) servers that associate an IP address with
the name of a device. When you administer the DNS with the Avaya server names, you
can access the servers by name and by IP address over the corporate network.
Set Static Routes — Use this page only if the network administrator instructs you. If the
administrator does not specify a particular route for the server to send information over the
network, leave the options blank and click Continue.
Configure Time Server — Use this page to specify the time source that the Avaya server
uses to set the time of day.
Set Modem Interface — Use this page to enable Avaya services or another
trouble-tracking service to monitor the Avaya server for alarms. Technical-support
representatives can dial in to this interface to fix problems as they occur.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 4: Server configuration

Ethernet interface assignments
Use the following table as a guide for assigning server functions to physical Ethernet interfaces.
Table 7: S8700-series Server Ethernet assignments
S8710/S8720/
S8730 hardware
duplication and
dedicated control
network

S8720/S8730
software
duplication with
dedicated control
network

S8710/S8720/
S8730 hardware
duplication with
non-dedicated
control network

S8720/S8730
software
duplication with
non-dedicated
control network

Control network A

eth0

eth2

eth0

eth2

Control network B

eth3 (if used)

LAN

eth4

eth0

eth2

Duplication Link

eth2

eth0

eth2

eth0

Performing the manual configuration
To configure the server using the manual method:
1. Log into the server and bring up the Integrated Management Maintenance Web Pages.
2. From the Main Menu, under Server Configuration and Upgrades click Configure Server.
3. Click through the Review Notices to get to the Select Method for Configuring Server page.
4. Select "Configure all services using the wizard" and click continue to get to the Set Server
Identities page.
5. Fill in the fields on the Set Identities page and subsequent pages:

●

Configure Interfaces

●

Configure ESS

●

Configure Memory (S8720 only)

●

Configure Switches

●

Set DNS/DHCP

●

Set Static Routes

●

Configure Time Server

●

Set Modem Interface

Installing and Configuring the Avaya S8700-Series Server

January 2008

Methods of Configuring a server

●

Update System

Use your pre-installation planning forms to enter information on these pages. For more
information on these pages, see Configuring the server manually on page 37 or click on
the Help button at the bottom of each page.
6. When you complete all the fields, click Continue on the Update System page. The Update
System page displays each configuration task as it completes it. The last line says,
"System modifications completed."

Avaya Installation Wizard
About the Avaya Installation Wizard
Use the Avaya Installation Wizard to:
●

Set the date, the time, and the time zone

●

Configure the server

●

Install the RFA license file
Note:
To install the license file the server does not have to be connected to the
reference IPSI. However, you have only 30 minutes before the system checks the
serial number on the IPSI. To add another 30 minutes, type reset system 1
and press Enter in a SAT session to restart the Communication Manager
software.

Note:

●

Install the Avaya authentication files

●

Install software updates

●

Set the product ID

●

Set the alarming

The Avaya Installation Wizard cannot be used to configure:
●

Note:
To configure XL or Standard Memory, use the Configure Server in the Integrated
Management Maintenance Web Pages. For more information see, Configuring
memory for an S8720 Server on page 44.

Note:

●

Note:

Extra Large (XL) or Standard Memory Configuration (S8720 only)

Encryption setting for Software Duplication (S8720 or S8730 with Software Duplication)
Note:
To configure Software Duplication, use the Configure Server in the Integrated
Management Maintenance Web Pages.

To use the Installation Wizard, you can either:

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 4: Server configuration

●

Import the data from the completed Electronic Preinstallation Worksheet (EPW). When the
Installation Wizard prompts you to import the Preinstallation Worksheet, click Import EPW
and browse to the location of the EPW file on your Services laptop computer. The
Installation Wizard opens the EPW and uploads the configuration data.
Type the information manually with the completed EPW as a guide. The Installation Wizard
prompts you to enter the configuration data for each step in the Configure Server section.

Running the Avaya Installation Wizard
1. With the Web browser open, type 192.11.13.6 and press Enter in the browser address
window to display the login page.
2. Log in as craft and use the initial craft password.
3. Click Launch Avaya Installation Wizard.
4. Follow the prompts. For more information use Help on each page.
!

CAUTION:
The license settings for the platform and the port network connectivity (PNC)
attributes for the S8700-series Server can be complex. For more information, see
PNC license settings for S8700-series Servers on page 9.

WARNING:
If the time zone is set in the AIW, you must reboot the server after AIW
completes.

CAUTION:

WARNING:

5. Reboot the server:
a. Click Shutdown Server under the Server heading.
b. Select Delayed Shutdown and Restart server after shutdown.
c. Click Shutdown.
You will be logged off the server when it reboots. You can use ping to verify when the
server is accessible again.

Verifying the server connection to the customer LAN (if
provided)
1. From the Maintenance Web Interface, under Diagnostics, click Ping.
2. Select Host Name Or IP Address and type the IP address of a computer on the network.
3. Click Execute Ping.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Configuring the modem

4. Verify that the ping was successful and indicates that the server is connected to the
customer network.
5. If DNS is administered, type the host name of a computer on the network.
6. Click Execute Ping.
7. Verify that the ping was successful and indicates that DNS is working.
If possible, have a customer representative perform the following test from a computer on the
network:
1. Click Start > Run to open the Run dialog box.
2. Type command and click OK to open an MS-DOS command window.
3. Type ping serveripaddress and press Enter, where serveripaddress is the IP
address of the server.
4. Verify that the ping was successful.
5. If DNS is administered, type ping servername and press Enter, where servername is
the host name of the server.
6. Verify that the ping was successful.

Configuring the modem
1. From the Maintenance Web Interface, under Server Configuration click Configure Server.
2. Click Continue until you get to the Specify how you want to use this wizard page.
3. Select Configure individual services and click Continue.
4. On the menu on the left, click Set Modem Interface.
5. Select Change Modem Setting and click Continue.
6. In the Extra Modem Initialization Commands window, type the initialization commands that
are appropriate for your modem and the country of operation. Click Help for help on what
to enter.
For example, to change the country code to Japan, type AT%T19,0,10.
7. Click Change.
The system displays a message that indicates that a modem route was added
successfully.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 4: Server configuration

Configuring memory for an S8720 Server
For an S8720 Server, you must select the memory configuration to be used: either Standard or
Extra Large. If Hardware Duplication is turned on, administration for the S8720 in an XL
configuration is allowed only if the servers are equipped with DAL2 duplication memory cards.

Note:

Note:
If the customer chooses to increase the number of VAL circuit packs or the
number of Logged-In Agents, the customer will need to get a new License File
with increased capacities.
Note:
If the main servers are S8720 configured as Extra Large (XL), ESSs and LSPs
must be configured as XL. See Ensuring ESS and LSP compatibility on page 45.
1. Before configuring the memory, stop Communication Manager by running the bash
command stop -acf.
2. From the Maintenance Web Interface, under Server Configuration, click Configure
Server.
3. Click Continue until you get to the Specify how you want to use this wizard page.

4. Select Configure individual services and click Continue.
5. On the main menu under Configure Individual IP Services, click
●

Configure Memory (if a main server)

Installing and Configuring the Avaya S8700-Series Server

January 2008

Ensuring ESS and LSP compatibility

●

Configure ESS (if an ESS server)

6. Select either Standard or Extra Large.
7. Click Change to change values.
8. Click Close Window.
9. Start Communication Manager by running the bash command start -ac.
10. Run the bash command swversion.

Ensuring ESS and LSP compatibility
If the main servers are S8730, or if the main servers are S8720 configured as XL, ESSs and
LSPs must be configured as XL. S8300B LSPs cannot be configured as XL, and are not
compatible with S8730 Servers or with S8720 Servers configured as XL. S8710 ESSs cannot
be configured as XL, and are not compatible with S8730 Servers or with S8720 Servers
configured as XL.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 4: Server configuration

Enabling firewall settings
For the server to receive SNMP traps from the UPS and the Avaya Ethernet switch, you must
enable the snmptrap,162/udp port. The default is disabled.
1. From the Maintenance Web Interface, under Security, click Firewall.
2. Scroll down to the snmptrap 162/udp row and select (check) the Input to Server box.
The Output to Server box can be left as is, either checked or clear.
3. Click Submit.

Enabling network time servers
!
Important:

Important:
Avaya strongly recommends that you enable Network Time Protocol (NTP) and
configure at least one network time server. If a network time server is not used the
Date/Time settings on the server must be reset regularly, at least monthly, using
the Maintenance Web Interface. The network time strategy is determined by the
network administrator.

With NTP, you can specify one, two, or three network time servers to provide the accurate time
of day data to the clocks on the servers. The network time servers, in turn, get their source
timing from one of several highly accurate time services that are available on the Internet.
To use a network time server, the NTP service must be enabled. The Avaya Installation Wizard
prompts you to enable the NTP service. If you do not use the Installation Wizard, use the
Configure Server function on the Maintenance Web Interface to configure the network time
servers.
1. From the Maintenance Web Interface, under Server Configuration, click Configure
Server.
2. Click Continue on the Review Notices page and the Backup Up Data page.
3. On the "Specify how you want to use this wizard" page, select Configure individual
services and then click Continue.
4. In the menu on the left side of the Configure Server page, click Configure Timer Server.
5. Enter the NTS information on the Configure Time Server screen and click Change.
6. On the main menu, under Security, click Firewall.
7. In the "Output from Server" column, select ntp 123/udp.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Configuring the NIC

Note:

Note:
It is not necessary to enable the "Input to Server" ntp service. If this service is
already enabled, you do not need to disable it.

When the Avaya Installation Wizard prompts you for information about the network time
servers, enter the DNS name or the IP address for the primary network time server and the
secondary and the tertiary time servers if any. If you enter a DNS name instead of an IP address
for the network time server, you must specify the IP address of the DNS server on the DNS/
DHCP web page. For more information, see About the Avaya Installation Wizard on page 41.
For more information about NTP, see RFC 958.

Configuring the NIC
1. From the Maintenance Web Interface, under Server Configuration, click Configure
Server.
2. Click Continue until you get to the "Specify how you want to use this Wizard" page.

3. Select Configure Individual Services and click Continue.
4. On the menu on the left, click Set Identities
5. Use the drop-down menus to assign the Ethernet port functions. Click Continue.
6. Complete the following information for Ethernet 2:
●

IP address

●

Gateway

●

Subnet mask

●

Speed

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 4: Server configuration

7. Verify with the network administrator that the LAN hardware supports 802.1q priority
tagging. If supported, select VLAN 802.1q priority tagging.
8. Click Change. The system displays the status of the configuration update.
When the update is complete, the system displays the following message:
Successfully configured ethernet interfaces.

Release the server
Unplug the cross-over cable from the Services port on the back of the server.

Configuring a second server
Use the same procedures that you used to configure the first server. Repeat Clearing the ARP
cache on the laptop on page 31 through Release the server on page 48 for the second server.

Interchanging servers
Perform an interchange between the two servers to verify that an interchange will work
correctly.

Accessing the standby server
To access the standby server:
1. Clear the ARP cache on the laptop if necessary. For more information, see Clearing the
ARP cache on the laptop on page 31 and return here.
2. Connect the laptop to the Services port (2) on the back of the server with a cross-connect
CAT5 cable.
3. Open a browser and connect to the active server.
4. If you are not already logged in to the Maintenance Web Interface, log in. For more
information, see Accessing the Maintenance Web Interface on page 93.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Interchanging servers

Interchanging servers
To interchange the servers to check capability of the standby server to become the active
server:
1. Under Server, click Interchange Servers.
2. Verify the settings in the following fields:
●

Standby Busied: no

●

Standby Refreshed: yes

●

Standby Shadowing: on

●

Duplication Link: up

●

Control Network health: X/X/X for both servers, where X is the number of
administered IPSI port networks. For more information, see Chapter 5: IP interface
translations on page 51.

3. Click Interchange.
The system displays a confirmation message that the interchange has taken place.
This server is now the active server.
To perform another interchange so that the originally active server returns to being the active
server:
1. Access the server that is now the standby server. See.
2. Repeat the three steps for Interchanging servers.

Performing an integrity check on the active server
To perform an integrity check on the active server:
1. On the Maintenance Web Interface, under Diagnostics, click Server > Status Summary.
2. Verify the following:
Mode: Active
Server Hardware: okay
Processes: okay
3. Select Server > Process Status.
4. Under Frequency, click Display Once.
5. Click View.
6. Verify all operations are UP.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 4: Server configuration

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 5: IP interface translations
To administer IPSI circuit packs, use a terminal emulation program to issue Communication
Manager SAT commands.
For Communication Manager terminal emulation, use a program such as Avaya Native
Configuration Manager, Avaya Terminal Emulation, or HyperTerminal.
You also can use Avaya Site Administration to issue SAT commands. To administer some of the
features in the latest release of Avaya Communication Manager, you must use the latest
version of Avaya Site Administration.
Perform these tasks to administer IPSI circuit packs:
●

Inputting initial system translations on page 51

●

Adding media gateways on page 52

●

Enabling the IPSI on page 53

●

Adding the IPSI to the system on page 54

●

Enabling IPSI duplication (duplicated control network only) on page 55

●

Setting the alarm activation level on page 55

●

Saving translations on page 55

Inputting initial system translations
1. Open a SAT session. See Using the SAT command line prompt on page 94.
2. Enter translations:
If the system translations were prepared offsite, enter the translations and reset the server.
If the translations are not available, enter minimal translations to verify connectivity to the
port networks.
3. After you enter the translations, type save translation and press Enter to save the
translations to the hard disk drive.
4. Type reset system 4 and press Enter to have the software read the copied
translations.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 5: IP interface translations

Adding media gateways
Note:

Note:
If system translations have been loaded on the server, media gateways do not
need to be added to administer the IPSI.
1. Type add cabinet n and press Enter, where n is the cabinet number, for each stack of
media gateways that is controlled by one TN2312BP IPSI circuit pack.
A cabinet is defined as a group of up to five G650 Media Gateways that are mounted in a
rack and TDM-connected.
2. Fill in the carrier location letter and the carrier type for each media gateway in the cabinet.
add cabinet 1

Page

1 of

CABINET
CABINET DESCRIPTION
Cabinet:
Cabinet Layout:
Cabinet Type:
Number of Portnetworks:
Survivable Remote EPN?
Location:
Cabinet Holdover:
Room:

1
G650-rack-mount-stack
expansion-portnetwork
1
n
1
IP Network Region:1
A-carrier-only
Floor:

CARRIER DESCRIPTION
Carrier
Carrier Type
E
D
C
B
A

not-used
not-used
not-used
G650-port
G650-port

Building:

Number
PN
PN
PN
PN
PN

09
09
09
09
09

Installing and Configuring the Avaya S8700-Series Server

January 2008

Enabling the IPSI

Enabling the IPSI
1. Type change system-parameters ipserver-interface and press Enter.
2. On a duplicated server, the system displays the following screen. Verify that the primary
control and the secondary control subnetwork addresses are correct.
change system-parameters ipserver-interface

Page

1 of

IP SERVER INTERFACE (IPSI) SYSTEM PARAMETERS
SERVER INFORMATION
IPSI Host Name Prefix: birch
Primary Control Subnet Address: 198.152.254.
Secondary Control Subnet Address: 198.152.255.

0 *
0 *

OPTIONS
Switch Identifier: A
IPSI Control of Port Networks: enabled

The control subnetwork addresses typically match the most significant three octets of the
IP addresses of the server for the media gateway. The most significant three octets are the
first three groups of digits in the IP address. Select the configure server command on
the Maintenance Web Interface to see the IP address of the server.
An asterisk (*) to the right of the Control Subnet Address field means that
Communication Manager does not have the subnetwork information and the subnetwork
address displayed is incorrect.
3. If the information in the Primary Control Subnet Address field, the Secondary Control
Subnet Address field, or both fields is incorrect, use the Maintenance Web Interface to
change the server configuration to match the Server IP address in configure server.
Under Server Configuration and Upgrades, click Configure Server to change the server
configuration. Then return to this procedure.
4. Set the Switch Identifier field to the switch ID letter. Acceptable switch ID letters are A
through J. A is the default setting.
5. Set the IPSI Control of Port Networks field to enabled.
6. Press Enter to save the changes.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 5: IP interface translations

Adding the IPSI to the system
Use the IP Server Interface Administration - Port Network SAT screen to add an IPSI. The
information on this screen differs, depending on whether the IP addresses of the IPSI are static
or assigned automatically through DHCP.
1. Type add ipserver-interface PNnumber and press Enter.
2. For the Host field and the DHCP ID fields for the primary IPSI and secondary IPSI, if any:
●

●

For dynamic addressing, the DHCP server sets the Host field and the DHCP ID field.
Verify that the fields are populated with default data.
For static addressing, in the Host field, enter the IP address for the IPSI that is listed in
the Location field.

add ipserver-interface 4
Page
IP SERVER INTERFACE (IPSI) ADMINISTRATION - PORT NETWORK 4

1 of

IP Control? y
Socket Encryption? n
Ignore Connectivity in Server Arbitration? n
Enable QoS? n
Administer secondary ip server interface board? y
Primary IPSI
-----------Location: 9A01
Host: ipsi-A09a
DHCP ID: ipsi-A09a

Secondary IPSI
-------------Location: 9B01
Host: ipsi-A09b
DHCP ID: ipsi-A09b

add ipserver-interface 8
IP SERVER INTERFACE (IPSI) ADMINISTRATION - PORT NETWORK 8
IP Control? y
Ignore Connectivity in Server Arbitration? n
Primary IPSI
-----------Location: 1A01
Host: 172.22.22.174
DHCP ID: ipsi-A01a

Socket Encryption? n
Enable QoS? n
QoS Parameters
-------------Call Control 802.1p: 6
Call Control DiffServ: 46

3. Set the IP Control field to y.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Enabling IPSI duplication (duplicated control network only)

4. Verify that all the other fields are populated and submit the form to save the changes.
5. Repeat this procedure for each port network.

Enabling IPSI duplication (duplicated control network
only)
Port networks with duplicated IPSIs have both primary (CNA) and secondary (CNB) IPSI circuit
packs. If you disable IPSI duplication, all primary IPSI circuit packs must be active.
Use the System-Parameters Duplication SAT screen to enable IPSI duplication.
1. Enter change system-parameters duplication.
2. Enter y in the Enable Operation of IPSI Duplication field.
3. Submit the screen to save the changes.

Setting the alarm activation level
1. At the SAT, type change system-parameters maintenance and press Enter.
2. In the CPE Alarm Activation Level field, enter none, warning, minor, or major,
according to the customer request.
3. Submit the screen to save the changes.
4. Repeat this procedure for each IPSI.

Saving translations
To save the translations to the hard disk drive, at the SAT, type save translation and press
Enter.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 5: IP interface translations

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 6: IP interface configuration
This chapter covers the following tasks:
●

Connecting to the IPSIs on page 57

●

IPSI address configuration on page 57

●

Programming the IPSI for static addressing on page 58

●

Setting the VLAN and diffserv parameters on page 61

●

Programming the IPSI for DHCP addressing on page 62

●

Verifying connectivity to the server on page 65

●

Verifying that the IPSIs are translated on page 65

●

Upgrading the IPSI firmware version (if necessary) on page 65

●

Enabling control of the IPSIs on page 65

●

Verifying the license status on page 66

At a minimum, you must program and connect to the reference TN2312BP IP Server Interface
(IPSI) so that the system does not enter No License Mode. Once you connect the IPSIs to the
control network, the IPSIs might generate an alarm if the firmware is not the most current. The
alarm stops automatically once you upgrade the IPSI firmware.

Connecting to the IPSIs
Connect CAT5 cables from the IPSI circuit packs to the dedicated control network or to the
customer LAN.

IPSI address configuration
The IPSI circuit pack receives an IP address:
●

●

Statically with static IP addressing, if the control network is nondedicated (public) through
the customer network.
Dynamically with dynamic host configuration protocol (DHCP), if the control network is
dedicated (private).

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 6: IP interface configuration

Note:
To program DHCP addressing, you must complete certain sequences within a
predetermined time-out interval. Avaya recommends that you read the following
procedure completely before you start so that you are familiar with these
sequences in advance.

Note:

Perform one of the following tasks depending on whether you use static or dynamic addressing:
●

Programming the IPSI for static addressing on page 58

●

Programming the IPSI for DHCP addressing on page 62

Programming the IPSI for static addressing
!
Important:

Important:
If an IPSI is in a port network that is backed up with the Enterprise Survivable
Server (ESS) option you must use static addressing for the ESS to provide
service to the port network.

You administer the static IP address for the circuit pack directly through the Ethernet port
connection on the faceplate (top port). See Figure 5.

Installing and Configuring the Avaya S8700-Series Server

January 2008

IPSI address configuration

Figure 5: Connecting the laptop directly to the IPSI

CLK

S
E
R
V
I
C
E
N
E
T
W
O
R
K

2
3

cadlipsi KLC 031502

Figure notes:
1. Services laptop computer
2. PCMCIA Network Interface Card (NIC)

Note:

3. NIC adapter cable (if necessary)
4. CAT5 crossover cable to IPSI

Note:
Ensure that you have the password before proceeding.

Depending on the operating system on the Services laptop computer, you might need to clear
the Address Resolution Protocol (ARP) cache before entering a new IP address. If you enter an
IP address and your computer cannot connect, try clearing the cache.
1. On your laptop computer, click Start > Run to open the Run dialog box.
2. Type command and click OK to open a MS-DOS Command Line window.
3. Clear the Address Resolution Protocol (ARP) cache in the laptop.
4. To log into the IPSI, use SSH and the IP address 192.11.13.6.
For information on how to use SSH, see Accessing the command line interface of the
server with SSH on page 87.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 6: IP interface configuration

Note:

Note:
While connected to the IPSI, type help or ? to obtain online help. Most
commands have two or three letter abbreviations.
5. Type ipsilogin and press Enter.

Note:

Note:
The craft login used on the IPSI has a different password from the craft login used
on the servers.
6. Log in as craft.
Prompt = [IPADMIN]:
7. Type show control interface and press Enter and then type show port 1 and
press Enter to see the current control interface settings.
8. To set the control interface, type set control interface ipaddr netmask and
press Enter, where ipaddr is the customer-provided IP address and netmask is the
customer provided subnet mask.

9. Type quit and press Enter to save the changes and exit the IPSI session.
10. Log back in to the IPSI using SSH.
11. Type show control interface and press Enter.
The system displays IP address, subnet mask, and default gateway information.
Verify that the proper information was entered.
12. If a default gateway is used, enter the gateway IP address with
set control gateway gatewayaddr, where gatewayaddr is the customer-provided
IP address for their gateway.
13. Type quit and press Enter to save the changes and exit the IPSI session.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Setting the VLAN and diffserv parameters

14. Log back in to the IPSI using SSH.
15. Use show control interface to verify the administration.
16. Type exit and press Enter.

Setting the VLAN and diffserv parameters
1. Connect to the IPSIand log in as craft.
2. To display the quality of service values, type show qos and press Enter.
3. Use the set commands in the list below to set the VLAN, diffserv, and port parameters. If
the customer does not specify different values, use these recommended values.

Note:

Note:
Use Help to obtain syntax guidelines for these commands.

!
Important:

Important:
The settings for these parameters on the IPSIs must be consistent with the
settings on the servers and other network devices such as Ethernet switches.

●

set vlan priority 6

●

set diffserv 46

●

set vlan tag on

●

set port negotiation 1 disable

●

set port duplex 1 full

●

set port speed 1 100

4. Type show qos and press Enter to check the administered values.
5. Type reset and press Enter to capture the updated parameter values.
The reset terminates the administration session and automatically logs you out.
6. Log in again and use the show qos command to ensure that the parameter settings are
correct.
7. Disconnect the laptop from the IPSIfaceplate.
8. Check the LED on the IPSIfaceplate. Verify that the display shows the letters I and P and a
filled-in V at the bottom. (See Figure 6).

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 6: IP interface configuration

Figure 6: IPSI LED display for static address

CLK

S
E
R
V
I
C
E

ledlip1 KLC 030502

N
E
T
W
O
R
K

Figure notes:
1. IPSI has a static IP address

Note:

2. IPSI has connectivity and an IP address

Note:
Clear the ARP cache on the laptop before connecting to another IPSI. If you do
not clear the cache, the laptop appears to stop and does not connect to the next
IPSI.
9. Repeat this procedure for each IPSI circuit pack.

Programming the IPSI for DHCP addressing
!
Important:

Important:
If an IPSI is in a port network that is backed up with the Enterprise Survivable
Server (ESS) option you must use static addressing for the ESS to provide
service to the port network.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Setting the VLAN and diffserv parameters

For the TN2312BP IPSI circuit packs to receive IP addresses dynamically, you first must assign
the switch ID and cabinet number to each IPSI circuit pack.The switch ID is a single letter, A
through J. The cabinet number is a 2-digit number, 01 through 64. For G650 Media Gateways, a
cabinet is defined as one or more media gateways connected by a TDM cable. This cabinet
configuration is called a G650-rack-mount-stack.

Note:

Note:
In the following procedure, you must start step 2 within 5 seconds after inserting
the circuit pack.
1. Fully insert the TN2312BP IPSI circuit pack. If necessary, reseat the circuit pack to start
the programming sequence.

Note:

Note:
For the following step, do not use a graphite pencil.
2. Insert a pen, golf tee, or similar object into the recessed push button switch.

S
E
R
V

Note:

fpdlled3 LJK 022502

CLK

Note:
If you pass the letter or number that you want, you have two options. You can
cycle through all the letters or numbers to get to the one you want. Or, you can
reinsert, or reseat, the circuit pack and start again.
Note:
If you have only one system, the default switch ID is A. The second system is B
and so on. The switch ID is not the media gateway or carrier letter.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 6: IP interface configuration

3. While the display characters are flashing, press the button until the switch ID, A through J,
shows on the top character of the LED display. When the correct letter shows, stop. The
letter flashes a few times, or 5 seconds, then stops. The next character down starts to
flash. This is the first digit of the cabinet number.

Note:

Note:
The number to program is the cabinet number, not the port network number. If
you have more than one IPSI in a cabinet, they all have the same cabinet
number.
4. While the first digit of the number is flashing, press the button until the correct tens digit, 0
through 6, for the cabinet number shows on the display. When the correct digit appears,
stop. The digit flashes for about 5 seconds, then stops. Then the second digit starts
flashing.
5. While the second digit is flashing, press the button until the correct units digit, 0 through 9,
for the cabinet number shows on the display. When the correct digit shows, stop. The digit
flashes for about 5 seconds, then stops.
6. All segments of the display go dark for one second. Then, the Switch ID and media
gateway stack number shows in the top three characters of the LED display. A "V" is
shown in the fourth or bottom character. When the DHCP server assigns an address to the
IPSI, the center of the "V" fills in. The filled in "V" looks like the bottom half of a diamond.

S
E
R
V

fpdlled2 LJK 022502

CLK

For a duplicated control network, repeat these steps for the second IPSI in the cabinet.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Verifying connectivity to the server

Verifying connectivity to the server
1. Open the Maintenance Web Interface and log in as craft.
2. Under Diagnostics, click Ping and select Other server(s), All IPSIs, UPS(s), Ethernet
switches to verify connectivity to these units.
3. Click Execute Ping.
4. Verify that all endpoints respond correctly.

Verifying that the IPSIs are translated
Note:

Note:
You must be on the active server to use SAT commands.
1. Use SSH to open a SAT session on the server.
2. Type list ipserver-interface and press Enter.
3. Verify that all ISPI circuit packs are translated.

Upgrading the IPSI firmware version (if necessary)
You might need to upgrade the firmware on some or all the IPSIs. All IPSIs must have the same
firmware load.
1. On the Maintenance Web Interface under IPSI Firmware Upgrades, click IPSI Version.
2. Select Query All and click View.
3. Verify the firmware release for each IPSI.
4. If an upgrade is required, follow the procedures in Firmware Download Procedures at the
Download Center on the Avaya Support web site.

Enabling control of the IPSIs
1. Ensure that the IPSIs have the same, current firmware.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 6: IP interface configuration

2. For duplicated IPSIs, enable IPSI duplication before you enable IPSI control. See Enabling
IPSI duplication (duplicated control network only) on page 55. On the SAT, type change
system-parameters ipserver-interface and press Enter.
3. Ensure the IPSI Control of Port Networks: field is set to enabled.
4. Submit the screen to save the changes.

Verifying the license status
On the Maintenance Web Interface, under Security, click License File and verify that the
license mode is now normal.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 7: Postinstallation administration
This section covers the following tasks:
●

Verifying translations on page 67

●

Setting rules for daylight savings time on page 68

●

Setting locations (if necessary) on page 69

●

Verifying the date and the time (main server only) on page 70

●

Clearing and resolving alarms on page 71

●

Enabling and disabling the Ethernet switch ports on page 71

●

Backing up files to the compact flash media on page 73

●

Enabling alarms to INADS by way of a modem on page 72

●

Enabling alarms to INADS by way of the SNMP module on page 73

●

Before leaving the site on page 74

Verifying translations
1. Open a SAT session on the server.
2. To view all the administered circuit packs in the system, type list configuration all
and press Enter.
3. To verify the location of the IPSI circuit packs,type list ipserver-interface and
press Enter.
For more information, see your planning documents and check the administration status on the
following items:
●

list station

●

list trunk-group

●

list hunt-group

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 7: Postinstallation administration

Setting rules for daylight savings time
You set the date, the time, and the time zone through the Maintenance Web Interface on the
server. You must use SAT commands to set the rules for daylight savings time.

Note:

Note:
The default setting of the daylight-savings-rules SAT screen reflect the US and
Canada rules effective in 2007.
1. Type change daylight-savings-rules and press Enter.
2. In the Change Day, Month, Date, Time, and Increment columns, type the appropriate
start and stop information for each rule. For example, 1:00 in the Increment field means to
move the clock forward or back by one hour at the transition point.
You can set up to 15 customized daylight savings time rules. If you have media gateways
in several different time zones, you can set up rules for these media gateways on a
per-location basis. A daylight savings time rule specifies the exact time when you want to
transition to and from daylight savings time. The rule also specifies the increment at which
to make the transitions.

Note:

Note:
The default daylight savings rule is 0, which means that no daylight savings
transition occurs. You can change any rule except rule 0. You cannot delete a
daylight savings rule if the rule is in use on either the Locations screen or the
Date and Time screens.
3. When you finish, submit the screen to save the changes.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Setting locations (if necessary)

Setting locations (if necessary)
After you set the rules for daylight savings time, you must set the locations for all port networks.
Port networks can be in different time zones. Use SAT commands to set the locations for the
port networks.
1. Type change locations and press Enter.
change locations

Page

1 of

LOCATIONS
ARS Prefix 1 Required For 10-Digit NANP Calls? y
Number
1
2
3
4
5
6
7
8
9
10
11

Name
Main
CA

Timezone
Offset
+ 00:00
- 02:00
:
:
:
:
:
:
:
:
:

Daylight-Savings
Rule
0
0

Number Plan
Area Code

2. In the ARS Prefix 1 Required for 10-Digit NANP Calls? field, type y.
3. Type the information in the various fields for each media gateway.
In the Name field for location 1, type Main.
4. Click Submit to save the changes.

Note:

Note:
The location of a port network is defined on the SAT cabinet form (change
cabinet X). The location of a network region is defined on the SAT
ip-network-region form (change ip-network-region X). The Location field
in the ip-network-region form is part of the association to the
daylight-savings-rule by which a IP phone behaves.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 7: Postinstallation administration

Verifying the date and the time (main server only)
Use SAT commands to verify the date and time.
1.Type display time and press Enter.
display time

Page

1 of

DATE AND TIME
DATE
Day of the Week: Friday
Day of the Month: 9

Month: June
Year: 2006

TIME
Hour: 14

Minute: 19

Second: 36

Type: Standard

Daylight Savings Rule: 0
WARNING: Changing the date or time may impact BCMS, CDR, SCHEDULED

2. Verify that the date and the time of day are correct.
If the date and the time of day are correct, go to 5.
If the date and time of day are not correct, proceed to step 3.
3. Verify connectivity to any administered Network Time Server:
a. Using the Maintenance Web Interface, click Network Time Sync under Diagnostics.
The Network Time Sync screen confirm synchronization to any administered Network
Time Server.
b. Resolve any connection or administration issues related to the Network Time Server. If
the Network Time Server is not administered:
1. In the Maintenance Web Interface, click Server Date/Time under the Server
heading. Set the correct date and the correct time. Verify that the time zone is
correct.

!
Important:

Important:
If you change the time zone, you must reboot the server.

4. Repeat this procedure, beginning with step 1.
5. Verify that the Daylight Savings Rule field is correct.
●
●

0 if this server is in a location that does not use daylight savings time
1-15 use an administered rule. The rule is administered using the SAT command
daylight-savings-rules. For more information on the daylight-savings-rules, see Setting
rules for daylight savings time on page 68.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Clearing and resolving alarms

Note:

Note:
The daylight savings rule setting on this form is the rule that is utilized by the
Communication Manager software. Additional daylight savings rules can be
implemented for the specific locations of hardware supported by the
Communication Manager software. For more information, see Setting locations (if
necessary) on page 69.

Clearing and resolving alarms
1. On the Maintenance Web Interface, under Alarms, click Current Alarms.
You can resolve alarms on the active server only.
2. Select the server alarms to clear and click Clear.
3. Using SAT commands or other standard troubleshooting procedures, to resolve any major
alarms.

Enabling and disabling the Ethernet switch ports
You might want to disable unused ports on the Avaya Ethernet switch, if used.
1. To select an Ethernet switch to administer, under Security, click Ethernet Switch Ports.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 7: Postinstallation administration

2. Select the switch you want to administer and click Submit.

3. Locate the ports that you want to disable and select Disable in that row.
4. Click Submit Changes.

Enabling alarms to INADS by way of a modem
Note:

Note:
Enable alarms on both servers.
1. Start an SSH session on the server.
2. Type almenable -d b and press Enter.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Enabling alarms to INADS by way of the SNMP module

3. To verify that the alarms are enabled, type almenable and press Enter.

Enabling alarms to INADS by way of the SNMP module
Note:

Note:
Perform this procedure only if the installation includes a Secure Service Gateway
(SSG).

To enable alarms on the servers:
1. Start an SSH session on the server.
2. Type almsnmpconf -d ipaddress -c communityname and press Enter, where
ipaddress is the trap receiver address for the SSG device and communityname is the
community string name that the SSG device requires.
3. Type almsnmpconf and press Enter and verify that the correct information is entered.
4. Type almenable -s y and press Enter.
5. Type almenable and press Enter and verify that alarm origination is enabled on the
SNMP module. If used, also verify that alarm origination by way of a modem is still
enabled.
6. Log off.

Backing up files to the compact flash media
Note:

Note:
Avaya requires the use of industrial grade compact flash media.
1. Connect the compact flash drive to one of the USB ports on the back of the server.
2. Insert the compact flash media into the top right slot of the drive.
3. On the Maintenance Web Interface, under Data Backup/Restore, click Backup Now.
4. Select all applicable data sets.
5. To back up the data onto the compact flash media, select Local PC Card.
To format a new media card, also select Format PC Flash.

Note:

Note:
You must format the compact flash media before the first use only.
6. Click Start Backup. The system displays a message when the format is completed, which
takes approximately 10 seconds.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 7: Postinstallation administration

Note:
If you click Start Backup without media in the compact flash drive, you cause a
system error. In this case, repeat the steps beginning with Step 1.

Note:

7. To view the status of the backup, click Backup Status.

Before leaving the site
●
●

Provide the default LAN security settings to the customer.
Ensure that the customer knows that remote access to the server is available only if the
following services are enabled on the Maintenance Web Interface Firewall screen:
- SSH must be enabled
- https must be enabled to access the Maintenance Web Interface
- def-sat must be enabled to access the SAT commands
- 162/udp must be enabled to receive SNMP traps from the UPS and the Avaya
Ethernet switch

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 8: Installation verification
This chapter provides the following information about how to verify the server installation and
configuration:
●

Testing the IPSI circuit packs

●

Testing the license file

●

Checking LED status indicators
- Servers
- Avaya Ethernet switches
- Uninterruptible power supplies (UPSs)
- Circuit packs

Testing the IPSI circuit pack
The following steps test the clock and packet interface components within the TN2312BP IPSI
circuit pack.

Note:

Note:
With duplicated servers, use the active server.
1. In a SAT command line, type test ipserver-interface UUC and press Enter,
where UUC is the cabinet and the carrier in which the circuit pack is located.
2. Verify that the Test Results screen shows PASS in the Results column.

Testing the license file
!
Important:

Note:

Important:
Wait at least 30 minutes after you install the Communication Manager license
before you run this test.

Note:
With duplicated servers, use the active server.
1. On a SAT command line, type test license and press Enter.
2. Verify that the Test Results screen shows PASS in the Results column.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 8: Installation verification

S8730 LEDs
Figure 7: LEDs on the front panel of the S8730 Server on page 76 and Figure 8: LEDs on the
back panel of the S8730 Server on page 77 show the LEDs on the S8730 Server.
Figure 7: LEDs on the front panel of the S8730 Server

POWER POWER
SUPPLY SUPPLY

DIMMS

PPM

PCI
RISER
CAGE

DIMMS

PROC PROC

INTER
LOCK

FANS

OVER
TEMP
I-PPM

UID

3
2

5
4

ms873lef LAO 082707

Figure notes:
1.
2.
3.
4.
5.

Note:

Active/standby LED
Internal health
External health
NIC 1 (Eth0) link/activity
NIC 2 (Eth1) link/activity

6. Power on/standby button/system power. Amber means
system shut down, but power still applied. Green means
system on. To turn off the power, press and hold the Power
button for several seconds.
7. Hard Drive LEDs
8. System Insight Display LEDs, which represent the system
board layout.

Note:
The Active/Standby LED, which is labeled as 1 in Figure 7, is on a push button.
When pushed, this button has no effect other than to turn off the LED
momentarily. The LED returns to the normal state within a few seconds after the
button is pushed.

Installing and Configuring the Avaya S8700-Series Server

January 2008

S8710 and S8720 LEDs

Figure 8: LEDs on the back panel of the S8730 Server
3

DAL1
DUP
MEMORY

LINC
ACTIVE

LINC
SYNC

TRANS
MODE

RECEIVE
MODE

4
2

3
1
PCIe 2

PCIe 1

ILO 2

UID

ms873leb LAO 081607

Figure notes:
1. NIC activity LED
2. NIC link LED
3. Power supply LED

4. Active/standby LED. Indicates active when on
steady or standby mode when blinking (blue).This
LED duplicates the Active/Standby LED on the front
panel.

S8710 and S8720 LEDs
Figure 7: LEDs on the front panel of the S8730 Server on page 76 and Figure 8: LEDs on the
back panel of the S8730 Server on page 77 show the LEDs on the S8710 and the S8720
Servers.
You cannot test the LEDs on the S8710 Server.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 8: Installation verification

Figure 9: LEDs on the front panel of the S8710 and the S8720 Servers

1
2
3
4

disc

1
2

Simplex

COMPACT

Duplex ch 1 ch 2

msdsled1 KLC 041304

Figure notes:
1. Internal health
2. Power supply
3. NIC 1 (Eth0) link/activity
(green)

Note:

4. NIC 2 (Eth1) link/activity (green)
5. Indicates active when on steady or standby mode when
blinking (blue)
6. Power on/standby button/system power. Amber indicates
power to the chassis is on but the server is off. Green
indicates power is on and the system is running. To turn off the
power, press and hold the Power button for several seconds.

Note:
The Active/Standby LED, which is labeled as 5 in Figure 9, is on a push button.
When pushed, this button has no effect other than to turn off the LED
momentarily. The LED returns to the normal state within a few seconds after the
button is pushed.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Additional server LED information

Figure 10: LEDs on the back panel of the S8710 and the S8720 Servers

1
3

2
3
2

4
3

LINC
ACTIVE

DAL1
DUP
MEMORY

LINC
SYNC

TRANS
MODE

RECEIVE
MODE

100 MGz

2
100 MGz
iLO

133 MGz

VDCI

UID

msds871c KLC 093004

Figure notes:
1. Not used
2. Not used
3. For hardware duplication mode on
the S8710, DAL2 fault (amber)
4. For hardware duplication mode on
the S8710, DAL2 power (green)

5. RJ45 link (green
6. RJ45 link (green)
7. Indicates active when on steady or standby mode
when blinking (blue)
This LED duplicates the Active/Standby LED on the
front panel.
8. Power supply (green)

Additional server LED information
For more information on server LEDs, see Maintenance Procedures for Avaya Communication
Manager, Media Gateways and Servers, 03-300432.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 8: Installation verification

Avaya C360 Ethernet switch LEDs
The C360 series converged, stackable, Ethernet switches include:
●

C363T: 24-port

●

C363T-PWR: 24-port power over Ethernet (PoE)

●

C364T: 48-port

●

C364T-PWR: 48-port PoE

The front panel of the C360-Series switches has:
●

One port LED that is associated with each port

●

Three system status LEDs

●

Seven port function LEDs

The C363T-PWR and the C364T-PWR switches have an additional PoE LED. The port function
LEDs are selectable with a set of two left/right buttons. The port LEDs display the status of the
selected function for each port.
For more information about the on/off and blinking states of the LEDs, see the documentation
for the Ethernet switch.
System and port function LEDs on C360 Avaya Ethernet switches
LED Name

Description

System LEDs
PWR

Power status

SYS

System status

ROUT

Routing mode

Port Function LEDs

LNK

Link status

COL

Collision status

Transmit to line

Receive from line

FDX

Full duplex mode

Hspd

High-speed mode

LAG

Link aggregation group for trunking

PoE (PWR versions only)

Power over Ethernet status

Installing and Configuring the Avaya S8700-Series Server

January 2008

UPS LEDs

UPS LEDs
The UPS LEDs flash briefly after the UPS is plugged in. The normal mode LED flashes after a
self-test to indicate that the UPS is in standby mode.
For more information, see the UPS user guide for the Powerware UPS.
Figure 11: LEDs on the Powerware 9125 UPS

ledlups KLC 030102

1
2

8
7
3

Figure notes:
1.
2.
3.
4.

Normal mode indicator
Battery mode indicator
Bypass mode indicator
Test/Alarm reset button

5.
6.
7.
8.

Off button
On button
Bar graph indicators
Alarm indicators

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 8: Installation verification

TN2312BP IPSI LEDs
TN2312BP IP Server Interface (IPSI) circuit pack LEDs include:
●

●

Standard LEDs and connector slots (Figure 12: TN2312BP IPSI circuit pack faceplate on
page 83)
A programmable LED display, which indicates:
- The type of IPSI IP address. For a dynamic address, the display shows media
gateway the location of the media gateway. For a static address, the display shows
I P. (Figure 13: IPSI LED display for a static IP address on page 84)
- Connectivity

Installing and Configuring the Avaya S8700-Series Server

January 2008

TN2312BP IPSI LEDs

Figure 12: TN2312BP IPSI circuit pack faceplate

1
10

2
3

9
4

CLK

N
E
T
W
O
R
K

01DR06142246

700060643

TN2312AP IPSI

ckdfips2 KLC 091403

AVAYA

S
E
R
V
I
C
E

Figure notes:
1.
2.
3.
4.
5.

Red LED
Green LED
Amber LED
Yellow LED (tone clock status)
Emergency transfer LED

6.
7.
8.
9.
10.

Services RJ45 connector
Network control RJ45 connector
Four-character LED display
Pushbutton switch
Slot for the maintenance cable

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 8: Installation verification

Figure 13: IPSI LED display for a static IP address

CLK

S
E
R
V
I
C
E

ledlip1 KLC 030502

N
E
T
W
O
R
K

Figure notes:
1. The IPSI has a static IP
address.

2. The IPSI has connectivity and an IP
address.

Installing and Configuring the Avaya S8700-Series Server

January 2008

TN2312BP IPSI LEDs

Figure 14: IPSI LED display indicating connectivity status for a DHCP IP address
2

ledlipsi KLC 030502

Connectivity status

The IPSI is connected to a server.

Yes

The IPSI has an IP address.

Yes

The Services laptop computer is connected to the
IPSI services port.

Yes

Installing and Configuring the Avaya S8700-Series Server

January 2008

Chapter 8: Installation verification

Installing and Configuring the Avaya S8700-Series Server

January 2008

Appendix A: Server access
Use a personal computer or a Services laptop computer that is equipped with a network
interface card (NIC), a terminal emulation program, and a Web browser to access a server for
initial configuration, aftermarket additions, and continuing maintenance.
You can access the server:
●

Directly

●

Remotely over the customer network

●

Remotely over a modem (for Avaya maintenance access only)

Steps to access a server include:
●

Connecting to the server directly on page 89

●

Connecting to the server remotely over the network on page 92

●

Connecting to the server remotely over a modem on page 92

●

Logins for Avaya technicians and BusinessPartners on page 95

●

Configuring the network for Windows 2000 and XP on page 95

Accessing the command line interface of the server with
SSH
The procedure in this section shows how to use SSH to log on to the server from a Services
laptop computer. SSH is the recommended method for server access. To use this procedure
with a cross-over cable connection from the computer to the Services port, you must configure
the computer for the network connection.
To use SSH, a third-party SSH client must be installed on your computer. PuTTY is one such
client. You can download PuTTY from http://www.putty.nl/download.html. The following
procedure describes, as an example of SSH access, how to log on to the server command line
with PuTTY.

Note:

Note:
A version of PuTTY that is defaulted for SSH server access is available for Avaya
Services personnel only. In this version, some values shown in the procedure
below are pre-selected.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Appendix A: Server access

Note:

Note:
Many Avaya products support access with SSH. However, Avaya does not
provide support for third-party clients that are used for SSH access. Problems
with an SSH client, including PuTTY, are the responsibility of the user or the SSH
client vendor.
1. On your computer, click on the PuTTY desktop link or click Start > Programs > PuTTY >
PuTTY.
The system displays the PuTTY Configuration window with the Session dialog box open.
2. In the Host Name or IP address field, type 192.11.13.6 if you want to connect to the
Services port. For access over the LAN or WAN, type the IP address or the host name of
the server.
3. In the Port field, type 22.
4. Under Protocol, select SSH.
5. In the PuTTY menu on the left, click Connection > SSH.
6. In the Preferred SSH protocol version field, select 2.
7. In the Encryption options window, use the up and down arrows to set AES (SSH-2) as the
top option and 3DES as the second option.

Note:

Note:
You can also customize the PuTTY tool with other settings, such as for color. For
documentation on PuTTY, see http://www.putty.nl/docs.html.
8. In the Backspace key area, select Control-H.
This activates the backspace key while you are using the SAT.
9. Click Open.

Note:

Note:
If you have not connected to this particular server before, SSH prompts you to
accept the server’s host key. If you save this key when prompted, you will not be
prompted if you connect again later. If you do not save the key, PuTTY prompts
you the next time you connect to this server.
When you connect though the interface on the Services laptop computer, if you save
the host key, the host is identified as 192.11.13.6. If you later connect to a different
server through the laptop interface, this new host also shows as 192.11.13.6, but it has
a different key. You get a prompt in this case because it appears that the host key has
changed.
10. If necessary, click Yes to accept the server’s host key.
The system displays the PuTTY window.
11. Log in as craft.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Connecting to the server directly

Connecting to the server directly
To access the server directly, use a computer with the following minimum specifications:
●

A Windows 2000 or Windows XP operating system

●

32-MB of RAM

●

40-MB of available disk space

●

An RS-232 port connector

●

A network interface card (NIC) with a 10/100BaseT Ethernet interface

●

A 10/100 BaseT Ethernet, category 5 or better, cross-over cable with an RJ45 connector
on each end (MDI to MDI-X)
A CD-ROM drive

1. Plug one end of the CAT5 cable into the Services access port on the back of the server.
For more information, see Figure 15: Services laptop computer connected directly to the
S8730 Server on page 90 or Figure 15: Services laptop computer connected directly to
the S8730 Server on page 90.
2. Plug the other end of the CAT5 cross-over cable into the NIC on your computer. Use a NIC
adapter if necessary.
3. Configure your network connection
●

IP address: 192.11.13.5

●

Subnetwork mask: 255.255.255.252

For specific information, see Configuring the network for Windows 2000 and XP on
page 95.
Once you connect, use a terminal emulation program or a Web browser to administer the
server.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Appendix A: Server access

Figure 15: Services laptop computer connected directly to the S8730 Server

2
3

DAL1
DUP
MEMORY

LINC
ACTIVE

LINC
SYNC

TRANS
MODE

RECEIVE
MODE

4
2

3
1
PCIe 2

PCIe 1

ILO 2

UID

ca873srv LAO 081507

Figure notes:
1. Services laptop computer
2. Network interface card (NIC)

3. NIC adapter cable (if necessary)
4. CAT5 cross-over cable

Installing and Configuring the Avaya S8700-Series Server

January 2008

Connecting to the server directly

Figure 16: Services laptop computer connected directly to the S8710 or S8720 Server

2
3

4
3

LINC
ACTIVE

DAL1
DUP
MEMORY

LINC
SYNC

TRANS
MODE

RECEIVE
MODE

100 MGz

2
100 MGz
iLO

133 MGz

VDCI

UID

cadlsrv2 KLC 042804

Figure notes:
1. Services laptop computer
2. Network interface card (NIC)

3. NIC adapter cable (if necessary)
4. CAT5 cross-over cable

Installing and Configuring the Avaya S8700-Series Server

January 2008

Appendix A: Server access

Connecting to the server remotely over the network
You can use any computer to connect to the server through a LAN. The security settings on the
LAN must allow remote access.
1. Open a Web browser or a terminal emulation application.
2. In the address field, enter the IP address or the DNS host name that is assigned to the
server that you want to access.
Enter the address of the active (alias) server to connect to the active server.

Connecting to the server remotely over a modem
Note:

Note:
Remote access over a modem is for Avaya services support access only and not
for routine administration. Because the server uses the same modem line to
report alarms, the server cannot report new alarms while the line is in use.

You can access the server through an analog modem. The remote connection requires a
minimum data speed of 33.5 kilobits per second.
1. Launch the dial-up connection program, which varies depending on your operating
system. Generally, you can access the program through the My Computer or the Control
Panel folders. For more information, see the Help system of your computer.
2. To open the New Connection wizard, double-click Make New Connection.
3. Within the wizard, depending on your operating system, you may be asked to:
●

Assign a name to the connection.

●

Select dial-up to the network for the network connection type.

●

Select the modem you will be using for the dial-up connection.

●

Enter the appropriate telephone number to access the active server. For the
customer-supplied telephone numbers, see the completed Electronic Preinstallation
Worksheet.
Under Advanced, select PPP and log on manually. You might have to type a user
name and password, depending on whether or not the server that you are dialing into
has a non-null CHAP secret key. If you need a user name and a password, use craft
for the user name and ignore the password field.

4. Click the connection name or icon, if created. Wait for connection.
5. When prompted, enter your remote access login name and password.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Accessing the Maintenance Web Interface

6. When the system displays the Start PPP now message, click Done. When you see the
Connection Complete dialog box, your computer is connected to the server.
7. Open an SSH session using PuTTY or other client.
See Accessing the command line interface of the server with SSH on page 87 for more
information.
8. Within the SSH client, type the IP address of the active server.

Finding the IP address of the active server
To find the active server IP address on a duplicated system:
1. Go to the task bar at the bottom right of your computer screen.

2. Right-click on the Network Status icon, and select Status, Details.
3. Scroll down until you see the Server IP address. This is the IP address for the server that
you are connected to.

Accessing the Maintenance Web Interface
You can administer the server through the Maintenance Web Interface. Access the
Maintenance Web Interface when connected:
●
●

Over the customer network with MS Internet Explorer 5.5 or 6.0.
Directly to the Services port on the server. For more information, see Figure 15: Services
laptop computer connected directly to the S8730 Server on page 90 or
Figure 15: Services laptop computer connected directly to the S8730 Server on page 90.

To access the Maintenance Web Interface, you must first bypass any proxy servers.
1. In Internet Explorer, click Tools > Internet Options.
2. Click the Connection tab.
3. Click LAN Settings in the lower right, then click Advanced.
4. In the Exceptions box after the last entry, type 192.11.13.6
5. Click OK to close each of the dialog boxes.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Appendix A: Server access

6. Open the MS Internet Explorer Web browser to access the Maintenance Web Interface.
●
●

Note:

If you are connected directly, in the Address field, type 192.11.13.6.
If you are connected remotely through a modem, in the Address field, type in the IP
address or the DNS host name of the server.

Note:
The first time that you log in, you see a message that asks you to install a security
certificate. Follow the instructions for your particular browser to accept the
certificate. You can also install the certificate on your computer with the
instructions in the online Help for your browser.
7. When prompted, log in.
8. When you see a message that asks Do you want to suppress alarms?, select Yes.
9. Click Launch Maintenance Web Interface.

Using the SAT command line prompt
Use a remote Secure Shell (SSH) or terminal emulation session to access the Communication
Manager SAT command line prompt.
Type of connection

Procedure

Using SAT with SSH:

See Accessing the command line interface of the server with
SSH on page 87.

Using SAT with Terminal
Emulation

To use a command line interface in a terminal emulation window,
open your terminal emulation application. Configure the terminal
emulation program port settings as follows:
● Speed: 115200 baud or 9600 baud if you use a serial
modem connection
● No parity
● 8 data bits
● 1 stop bit
● No flow control
NOTE: Avaya Native Configuration Manager, Avaya Terminal
Emulation, and HyperTerminal are the only terminal emulation
programs that Avaya supports.
Use either the IP address or the DNS host name to establish a
network connection to the active server. Use port 5023 for this
connection. Use SAT commands on the active server only. When
prompted, log in to the server as craft.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Logins for Avaya technicians and BusinessPartners

Logins for Avaya technicians and BusinessPartners
Avaya field technicians and BusinessPartners must use a Services login such as craft or
dadmin to perform initial configuration and upgrades. An Avaya field technician can use a
unique password that is assigned to the customer system.
After the Avaya authentication file is installed, Avaya Communication Manager has a password
for the craft login that is unique to the customer system and available when you are connected
directly to the server. If the system is configured without ASG, then all security authentications
are through passwords. If ASG is turned on, then all authentication is through ASG except for
logins over the service port which require a password. The revised password is recorded by
RFA and is obtained from ASG Conversant at 1-800-248-1234 or 1-720-444-5557.
Customers can set up their own logins to access Avaya servers. You must have superuser
permission to create or change logins and passwords. NOTE: do not start login IDs with a
number. For more information, see the Avaya Communication Manager Basic Administration
Quick Reference (03-300363).

Configuring the network for Windows 2000 and XP
!
Important:

Important:
Write down the original settings for use in case you need to revert to the original
configuration.

1. On your computer desktop, right-click My Network Places and left-click Properties to
display the Network Connections window.
Windows 2000 or Windows XP should automatically detect the Ethernet card in your
system and create a LAN connection. More than one connection might appear.
2. Right-click on the correct Local Area Connection and left-click Properties to display the
Local Area Connection Properties dialog box.
3. Select Internet Protocol (TCP/IP).
4. Click Properties to display the Internet Protocol (TCP/IP) Properties dialog box.
5. On the General tab, select Use the following IP address.
6. Make a note of any IP addresses or other entries that you have to clear. You might need to
restore them later to connect to another network
Enter the following:
●

IP address: 192.11.13.5

●

Subnet mask: 255.255.255.252

Installing and Configuring the Avaya S8700-Series Server

January 2008

Appendix A: Server access

7. Select Use the following DNS server addresses. The entries for Preferred DNS server
and Alternate DNS server should both be blank.
8. Click Advanced at the bottom of the dialog box to display the Advanced TCP/IP Settings
dialog box.
9. Click the DNS tab. Ensure no DNS server is administered. The address field should be
blank.
10. Click OK, OK, and Close to close all the windows.

Setting the browser options for Internet Explorer 6.0
A connection session to a server might time out when connected through a proxy server. To
avoid having the server time out during a session, add the server host names or IP addresses to
the list of host names and IP addresses.
To set browser options for Internet Explorer 6.0:
1. In Internet Explorer 6.0, click Tools > Internet Options.
2. Select the Connection tab.
3. Click on LAN settings, then Advanced.
4. In the Do not use proxy server for addresses beginning with field, type the IP address
for each server you intend to access remotely.
If the IP addresses have the first or first and second octets the same, you can shorten the
addresses to xxx.xxx.* (example, 135.9.*).
5. Click OK to close each dialog box.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Appendix B: Installation troubleshooting
This section provides some simple strategies to help you troubleshoot an installation of a
server. This section includes:
●

Troubleshooting the installation of the server hardware on page 97

●

Troubleshooting the configuration of the server hardware on page 98

●

Troubleshooting the installation of the license file and the Avaya authentication file on
page 100

Troubleshooting the installation of the server hardware
.

Problem
No power to the
UPS

Possible solution
●
●
●

No power to the
Ethernet switch

●
●
●

No power to the
server

●
●
●

The servers are
not shadowing
The IPSI LEDs
flash

●
●

●

●
●

Ensure that the UPS is plugged into the outlet.
Ensure that the outlet has power.
For other solutions, see the user guide for the UPS.
Ensure that the Ethernet switch is plugged into the UPS or the outlet.
Ensure that the UPS or outlet has power.
For other solutions, see the user guide for the Ethernet switch.
Ensure that the server is plugged into the UPS.
Ensure that the UPS has power.
Push the power button on the front of the server.
Make sure you are using a cross-over cable.
Make sure fiber optic cable is plugged in correctly, RX to TX and TX
to RX.
Ensure that the IPSIis in the correct slot. Use slot 1 for the G650
Media Gateway, slot 2 for the G600 Media Gateway, and the
Tone-Clock slot for all others.
Ping the IPSI from server.
Ping the server from the IPSI.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Appendix B: Installation troubleshooting

Troubleshooting the configuration of the server hardware
Troubleshooting the configuration of the server hardware
Problem
Cannot log in to the
UPS subagent

Possible solution
●
●
●

●

Cannot log in to the
Ethernet switch

●

Cannot log in to the
server

●

●
●
●

●

Cannot access the
Avaya Installation
Wizard

●
●
●
●
●

Ensure that the SNMP subagent is installed in the UPS.
Ensure that you are connected to the correct Ethernet port.
Ensure that you have the correct login ID and password. For
more information, see the user guide for the SNMP subagent.
Ensure that the network card on the laptop computer is
configured correctly.
Ensure that you are connected to the correct Ethernet port. (On
the Ethernet switch, the correct port is labeled Console)
Ensure that you have the correct login ID and password. See the
user guide for the Ethernet switch.
Ensure that the network card on the Services laptop computer is
configured correctly.
Check the link LED on the server. If the LED is off, a cable or
hardware problem exists.
Ensure that you are using SSH and not telnet.
Ensure that you are connected to the Services Ethernet port.
Ensure that you are using a cross-over cable between the
Services laptop computer and the server.
Ensure that the ARP cache is cleared on the Services laptop
computer. In an MS-DOS window, type arp -d 192.11.13.6
and press Enter.
Ensure that you have connectivity. In an MS-DOS window, type
ping 192.11.13.6 and press Enter.
Ensure that the NIC on the Services laptop computer is
configured correctly.
Ensure that you are plugged into the Services port.
Ensure that you are using SSH and not telnet.
Ensure that you are using the correct IP address, 192.11.13.6
Ensure that you are using the correct login and password.
Ensure that the NIC on the laptop is configured correctly.
1 of 2

Installing and Configuring the Avaya S8700-Series Server

January 2008

Troubleshooting the configuration of the server hardware

Troubleshooting the configuration of the server hardware (continued)
Problem
Cannot use SAT
commands

Possible solution
●

●
●
●

Cannot ping out to
the customer network
Cannot ping the
server from the
customer network
Cannot access the
server remotely

The LED display on
IPSI is flashing

●

Cannot access the
IPSI for static
addressing

No “V” shows on the
IPSI LED

●

The “V” on the IPSI
LED is not filled in
The system
generates an alarm
when first connect to
IPSI

●
●
●

Ensure that you are using the correct IP address, 192.11.13.6
and port 5023.
Ensure that you are using SSH and not telnet.
Ensure that you are using the correct login and password.
Make sure you are logged onto the active server.
Ensure that in the LAN security settings “output from server” for
icmp is enabled.
Ensure that in the LAN security settings “input to server” for icmp
is enabled.
Ensure that in the LAN security settings “input to server” is
checked for SSH (Linux commands), https (Web access), and
def-sat (SAT commands access). Change the LAN security
settings on the Web interface with a direct connection to the
server.
The IPSI LED is not programmed with the switch and the location
(DHCP)
An IP address is not assigned to the IPSI LED (static IP
addressing).
Ensure that you are plugged into the Services (top) port on the
IPSI.
Ensure that the ARP cache is cleared on the Services laptop
computer. In an MS-DOS command window, type arp -d
192.11.13.6 and press Enter.
The IPSI is not connected to the Ethernet switch or the network.
Connect a cable to the bottom port on the faceplate and to the
Ethernet switch or the customer network.
Make sure port on the Ethernet switch that is assigned to that
IPSI is enabled.
An IP address is not assigned to the IPSI.
The IPSI is not administered.
The IPSI does not have the current firmware. Upgrade the
firmware.

2 of 2

Installing and Configuring the Avaya S8700-Series Server

January 2008

Appendix B: Installation troubleshooting

Troubleshooting the installation of the license file and
the Avaya authentication file
Problem

Possible solution

Cannot get files from the RFA site

●
●

Cannot install the license file

●

The server is in no-license mode

●

Cannot use the administration
commands

ASG does not work
Cannot install the authentication
file

100

●

Provide the correct SAP number.
Provide the serial number for the reference IPSI.
Ensure that two license files do not exist on the server.
If so, delete one of the files.
The file might be corrupt. Download the file again from
the RFA site.
Use binary mode to upload the file.
The license file does not have an IP address yet. This
situation is normal when the license file is first installed
because the file cannot see the IPSI.
After 30 minutes, the license file has not located the
reference IPSI. In a SAT session, type reset
system 1 and press Enter to reset the 30-minute
clock.
The server might be in no license mode because the
30-minute timer lapsed. In a SAT session, type reset
system 1 and press Enter to reset the 30-minute
clock.

●

Re-install the Avaya authentication files.

●

Administer a super-user login on the active server.

Installing and Configuring the Avaya S8700-Series Server

January 2008

Index

Numerical
8730 Server configurations . . . . . . . . . . . . . 13

A
access server
directly . . . . . . . . . . . . . . .
remotely over modem . . . . . . . .
remotely over network . . . . . . .
accessing Maintenance Web Interface .
accessing the server . . . . . . . . . .
add
IP interface information . . . . . . .
media gateways . . . . . . . . . .
administer
IPSI circuit pack . . . . . . . . . .
AIW. See Avaya Installation Wizard
alarm activation level
setting . . . . . . . . . . . . . . .
alarms
enabling to INADS via SNMP . . . .
setting selected traps . . . . . . . .
to INADS by way of modem, enabling
viewing. . . . . . . . . . . . . . .
ARP cache, clearing . . . . . . . . . .
Avaya Installation Wizard, using . . . .

.
.
.
.
.

89
92
92
93
32

. . . . . . 54
. . . . . . 52
. . . . . . 57
. . . . . . 55
.
.
.
.
.
.

.
.
.
.
.
.

. . 73
. . 26
. . 72
. . 71
. . 31
. 37, 41

B
backing up files to compact flash . . . . . . . . . . 73

C
C363T or C364T Ethernet switch
configuring . . . . . . . . . . . . . .
LEDs . . . . . . . . . . . . . . . .
security alert . . . . . . . . . . . . .
clearing ARP cache . . . . . . . . . . .
collocated servers, connecting to . . . . .
command line interface . . . . . . . . . .
Communication Manager
installing software . . . . . . . . . . .
compact flash, backing up to . . . . . . .
configure
Avaya C363T or C364T Ethernet switch
media server 2 . . . . . . . . . . . .

.
.
.
.
.
.

27
80
27
31
19
94

. . . . . 31
. . . . . 73
. . . . . 27
. . . . . 48

modem . . . . . . . . . . .
network interface card (NIC) .
server . . . . . . . . . . .
UPS . . . . . . . . . . . .
connect to customer network . .
connection to LAN, verifying . . .
copy files to server . . . . . . .
customer network, connecting to

.
.
.
.
.
.
.
.

. . 43
. . 47
35, 51
. . 23
. . 13
. . 42
. . 36
. . 13

D
date and time, verifying . . . . . . .
daylight savings rules
location . . . . . . . . . . . . .
setting . . . . . . . . . . . . .
DHCP IP addressing
IPSI circuit pack . . . . . . . . .
using . . . . . . . . . . . . . .
diffserv parameters, setting . . . . .
direct access to server . . . . . . .
disable unused Ethernet switch ports
disconnecting from server . . . . . .
duplicated IPSIs, enabling . . . . . .

. . . . . . . . 70
. . . . . . . . 69
. . . . . . . . 68
.
.
.
.
.
.
.

.
.
.
.
.
.
.

57
62
61
89
71
48
55

E
enable Ethernet switch ports .
ESS compatibility . . . . . . .
Ethernet interface assignments
Ethernet switch
configuring . . . . . . . .
default IP addresses . . . .
disabling unused ports . . .
preparing to configure . . .
Extra Large configuration . . .

. . . . . . . . . . . 71
. . . . . . . . . . . 45
. . . . . . . . . . . 40
.
.
.
.
.

.
.
.
.
.

29
27
71
28
45

F
faceplate
TN2312BP circuit pack . . . . . . . . . . . . . 82
firewall settings . . . . . . . . . . . . . . . . . . . 46

I
INADS
enabling alarms to by way of modem . . . . . . . 72
inputting translations . . . . . . . . . . . . . . . . 51
installation

Installing and Configuring the Avaya S8700-Series Server

January 2008

101

Index
troubleshooting . . . . . . . . . .
using the Wizard . . . . . . . . .
installing
Communication Manager software .
translation file . . . . . . . . . .
interchanging servers . . . . . . . .
IP address
finding for the active server . . . .
set static . . . . . . . . . . . . .
use DHCP . . . . . . . . . . . .
IP address, set static . . . . . . . . .
IP interface
enabling control . . . . . . . . .
upgrading firmware version . . . .
verify translations . . . . . . . . .
IP interface information
adding to translations . . . . . . .
IPSI
connecting to . . . . . . . . . . .
enabling duplication . . . . . . . .
LEDs . . . . . . . . . . . . . .
program switch ID and cabinet . . .

. . . . . . . 97
. . . . . . 37, 41

modem, enabling alarms to INADS . . . . . . . . . 72

. . . . . . . 33
. . . . . . . 55
. . . . . . . 49

.
.
.
.

93
58
62
58

. . . . . . . 65
. . . . . . . 65
. . . . . . . 65
. . . . . . . 54
.
.
.
.

.
.
.
.

PNC license settings for S8700 . . . . .
post installation tasks . . . . . . . . . .
power
applying to media server . . . . . . .
pre-installation tasks at the installation site
Processor Ethernet . . . . . . . . . . .
PuTTY, SSH client . . . . . . . . . . .

. . . . . . . . . . . 79

.
.
.
.
.
.
.

S8700
active server, finding the IP address
port connections. . . . . . . . . .
S8700-series Media Server
PNC license settings . . . . . . .
S8700-series Server
LEDs . . . . . . . . . . . . . . .
S8730 Server
LEDs . . . . . . . . . . . . . . .
saving translations . . . . . . . . . .
separated servers, connecting to . . .
server
accessing . . . . . . . . . . . . .
configuring . . . . . . . . . . . .
copying files to . . . . . . . . . .
disconnecting from . . . . . . . .
LED, additional information . . . .
LEDs . . . . . . . . . . . . . . .
verify connectivity . . . . . . . . .
verifying LAN connection. . . . . .
server configuration, manual method. .
set
alarm activation level . . . . . . .
daylight savings rules . . . . . . .
selected traps (alarming) . . . . . .
static IP address . . . . . . . . .
set static IP address . . . . . . . . .

.
.
.
.
.
.
.

80
82
77
76
81
75
66

. . . . . . . . . . . 69
. . . . . . . . . . . 36
. . . . . . . . . . . 45

M
Maintenance Web Interface, accessing
manual configuration
configuration, manual method . . .
media gateways, adding . . . . . . .
media server
applying power . . . . . . . . . .
media server 2
configuring . . . . . . . . . . . .
modem
access to server . . . . . . . . .
configuring . . . . . . . . . . . .
connect to server . . . . . . . . .
modem options, setting . . . . . . . .

102

57
55
82
57

L
LED
additional information . . .
LEDs
Avaya Ethernet switches .
IPSI . . . . . . . . . . .
S8700-series Server . . .
S8730 Server. . . . . . .
UPS . . . . . . . . . . .
license file, testing . . . . . .
license, verifying status . . . .
location
setting for media gateways
login, super-user . . . . . . .
LSP compatibility . . . . . .

network interface card (NIC)
configuring . . . . . . . . . . . . . . . . . . . 47
network time server (NTP), enabling . . . . . . . . . 46

. . . . . . . 93
. . . . . . . 37
. . . . . . . 52
. . . . . . . 32
. . . . . . . 48
.
.
.
.

.
.
.
.

92
43
19
20

. . . . . . .9
. . . . . . 74
.
.
.
.

.
.
.
.

32
.9
20
87

RAID level 1 (S8730 server) . . . . . . . . . . . . . 13
remote access to server
over modem . . . . . . . . . . . . . . . . . . 92
over network . . . . . . . . . . . . . . . . . . 92

Installing and Configuring the Avaya S8700-Series Server

. . . . . . . 93
. . . . . . . 14
. . . . . . . .9
. . . . . . . 77
. . . . . . . 76
. . . . . 51, 55
. . . . . . . 19
.
.
.
.
.
.
.
.
.

.
.
.
.
.
.
.
.
.

. . 32
35, 51
. . 36
. . 48
. . 79
76, 77
. . 65
. . 42
. . 37

.
.
.
.
.

55
68
26
58
58

January 2008

Index

SNMP
preparing to configure . . . . . . . . . .
SNMP modules
administering . . . . . . . . . . . . . .
software, installing Communication Manager
spanning tree
enabling . . . . . . . . . . . . . . . .
setting version . . . . . . . . . . . . .
SSH
about . . . . . . . . . . . . . . . . .
access with. . . . . . . . . . . . . . .
static IP addressing
IPSI circuit pack . . . . . . . . . . . .
setting . . . . . . . . . . . . . . . . .
static IP addressing, setting. . . . . . . . .
super-user login . . . . . . . . . . . . . .

. . . . 25

. . . . 26
. . . . 33

verify
connectivity to servers . .
date and time . . . . . .
IP interface translated . .
license status . . . . . .
server connection to LAN
translations . . . . . . .
view alarms . . . . . . . .
VLAN parameters, setting . .

. . . . 29
. . . . 29
. . . . 21
. . . . 87
.
.
.
.

.
.
.
.

57
58
58
36

.
.
.
.
.
.
.
.

65
70
65
66
42
67
71
61

W
Wizard, installation . . . . . . . . . . . . . . . 37, 41

T
Telnet
configuring for Win2000/XP . .
terminal emulation . . . . . . . .
testing
license file . . . . . . . . . .
server installation . . . . . . .
TN2312BP . . . . . . . . . .
TN2312BP
faceplate . . . . . . . . . . .
LEDs . . . . . . . . . . . .
program switch ID and cabinet .
TN2312BP, testing . . . . . . . .
translation file
installing . . . . . . . . . . .
translations
inputting . . . . . . . . . . .
IP interface . . . . . . . . . .
saving . . . . . . . . . . . .
verifying . . . . . . . . . . .
troubleshooting, server installation

. . . . . . . . . 32
. . . . . . . . . 94
. . . . . . . . . 75
. . . . . . . . . 75
. . . . . . . . . 75
.
.
.
.

.
.
.
.

82
82
57
75

. . . . . . . . . 55
.
.
.
.
.

.
.
.
.
.

. . 51
. . 51
. 51, 55
. . 67
. . 97

U
upgrading
IP interface firmware version .
UPS
default IP addresses for S8700
LEDs . . . . . . . . . . . .
security alert . . . . . . . . .
SNMP module . . . . . . . .
UPS, configuring . . . . . . . . .
using DHCP IP address . . . . .
using this documentation . . . . .

. . . . . . . . . 65
.
.
.
.
.
.
.

.
.
.
.
.
.
.

24
81
23
23
23
62
. 8

Installing and Configuring the Avaya S8700-Series Server

January 2008

103

Index

104

Installing and Configuring the Avaya S8700-Series Server

January 2008

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-701
Copyright                       : 2008 Avaya
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : FrameMaker 7.0
Modify Date                     : 2007:12:05 11:58:27Z
Create Date                     : 2007:12:05 11:53:24Z
Format                          : application/pdf
Title                           : Installing and Configuring the Avaya S8700 Server
Creator                         : Linda M. Buckstein
Document ID                     : uuid:9a1d4325-7f46-480d-9e91-c7e39ac74497
Instance ID                     : uuid:d9f21f5b-5101-4f68-a785-cd7afb661e2a
Page Count                      : 104
Author                          : Linda M. Buckstein

EXIF Metadata provided by EXIF.tools

Avaya S8700 Installing And Configuring The Server User Manual To 06201bea 1be4 442b 9a20 C45c830d144a

Navigation menu

Versions of this User Manual:

Views

Navigation